REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested sources of supply. Suggested source of supply, modified 3.2.2, 3.2.6, and 6.1. Editorial changes throughout. Revised sources of supply, made editorial changes, and converted references to MIL-PRF-49467. Moved solderability testing from group A to group B. Updated suggested sources of supply. Removed suggested source of supply. Added note 4 to figure 1. Added capacitor tolerance note to 3.2.9. Added suggested source of supply. Added suggested source of supply. Added CalRamic Technologies as a suggested source of supply. 11 May 88 D. Moore 18 Jan 94 D. Moore 10 April 00 Kendall A. Cottongim 16 January 01 Kendall A. Cottongim 12 September 01 5 February 02 Kendall A. Cottongim Kendall A. Cottongim 19 April 2007 Michael A. Radecki B C D E F G CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME-Y14.100 REV STATUS G G REV G G G G G OF PAGES 3 4 5 6 7 PMIC N/A PAGES 1 2 Selected item drawing PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH Original date of drawing 24 June 1987 CHECKED BY HERALDINE JOHNSON APPROVED BY DAVID E. MOORE SIZE A REV AMSC N/A TITLE CAPACITORS, CERAMIC, MULTILAYER, HIGH VOLTAGE, X7R, 10,000 V DC CODE IDENT. NO. 14933 DWG NO. G PAGE 87081 1 OF 7 5910-E391 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49467 describe the complete requirements for high voltage multilayer ceramic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87081 | | Drawing number -XX | | Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Test Methods Standard Electronics and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://www.assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein (see figure 1). 3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. 3.1.2 Case. Epoxy, conformally coated. 3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 10,000 volts dc. 3.2.2 Dielectric type. X7R. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 2 Case code A B C Sizes (max.) Width (W) 1.050 1.250 1.450 Height (H) Inches .002 .025 .030 .270 .500 .600 .720 Lead spacing Thickness (T) .500 .600 .720 .270 .270 .270 ± .030 (S) .900 1.100 1.300 mm 0.05 0.64 0.76 6.86 12.70 15.24 18.29 Inches .900 1.050 1.100 1.250 1.300 1.450 mm 22.86 26.67 27.94 31.75 33.02 36.83 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. H dimension includes meniscus. 4. S dimension shall be maintained from chip body to end of leads. FIGURE 1. Case dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 3 3.2.3 Temperature coefficient. ±15 percent. (For MIL-PRF-49467 group B voltage temperature limits use step a through step d only.) 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25°C. 3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25°C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At +125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage. 3.2.8 Aging rate. -2.0 percent maximum per decade-hour. 3.2.9 Capacitance tolerance. K = ±10 percent, M = ±20 percent. K tolerance parts may be substituted for M tolerance parts, with procuring activity approval. 3.3 Solderability of terminals. In accordance with MIL-PRF-49467. 3.4 Vibration. In accordance with MIL-PRF-49467. 3.5 Shock. In accordance with MIL-PRF-49467. 3.6 Immersion cycling. In accordance with MIL-PRF-49467. 3.7 Moisture resistance. In accordance with MIL-PRF-49467. 3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.9 Thermal shock. Method 107, MIL-STD-202, test condition B except low temperature is -55°C. 3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.11 Terminal strength. In accordance with MIL-PRF-49467. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.15 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 4 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted. 4.2.2 Certification. The procuring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). TABLE I. Electrical characteristics DSCC drawing 8708101 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 Capacitance Capacitance tolerance Case code K M K M K M K M K M K M K M K M K A A A A A A A A A A A A A A A A A 470 pF 470 pF 560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF 1200 pF 1200 pF 1500 pF 1500 pF 1800 pF 1800 pF 2200 pF DSCC drawing 8708118 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Capacitance Capacitance tolerance Case code M K M K M K M K M K M K M K M K M A A A A A B B B B C C C C C C C C 2200 pF 2700 pF 2700 pF 3300 pF 3300 pF 3900 pF 3900 pF 4700 pF 4700 pF 5600 pF 5600 pF 6800 pF 6800 pF 8200 pF 8200 pF .01 µF .01 µF 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activities within the Military Service or Defense Agency, or within the military service's system commands. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CDROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 5 e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.4 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-4709 or DSN 850-4709. 6.5 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-4709 or DSN 850-4709. 1/ DSCC drawing PIN 8708101 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Vendor A similar vendor type Vendor B similar vendor type Vendor C similar vendor type Vendor D similar vendor type Vendor E similar vendor type SV10RC471KHA SV10RC471MHA SV10RC561KHA SV10RC561MHA SV10RC681KHA SV10RC681MHA SV10RC821KHA SV10RC821MHA SV10RC102KHA SV10RC102MHA SV10RC122KHA SV10RC122MHA SV10RC152KHA SV10RC152MHA SV10RC182KHA SV10RC182MHA SV10RC222KHA SV10RC222MHA SV10RC272KHA SV10RC272MHA SV10RC332KHA SV10RC332MHA SV11RC392KHA SV11RC392MHA SV11RC472KHA SV11RC472MHA SV12RC562KHA SV12RC562MHA SV12RC682KHA SV12RC682MHA SV12RC822KHA SV12RC822MHA SV12RC103KHA SV12RC103MHA 8840CX471KA103 8840CX471MA103 8840CX561KA103 8840CX561MA103 8840CX681KA103 8840CX681MA103 8840CX821KA103 8840CX821MA103 8840CX102KA103 8840CX102MA103 8840CX122KA103 8840CX122MA103 8840CX152KA103 8840CX152MA103 8840CX182KA103 8840CX182MA103 8840CX222KA103 8840CX222MA103 8840CX272KA103 8840CX272MA103 8840CX332KA103 8840CX332MA103 11050CX392KA103 11050CX392MA103 11050CX472KA103 11050CX472MA103 13060CX562KA103 13060CX562MA103 13060CX682KA103 13060CX682MA103 13060CX822KA103 13060CX822MA103 13060CX103KA103 13060CX103MA103 PCI1561-01 PCI1561-02 PCI1561-03 PCI1561-04 PCI1561-05 PCI1561-06 PCI1561-07 PCI1561-08 PCI1561-09 PCI1561-10 PCI1561-11 PCI1561-12 PCI1561-13 PCI1561-14 PCI1561-15 PCI1561-16 PCI1561-17 PCI1561-18 PCI1561-19 PCI1561-20 PCI1561-21 PCI1561-22 PCI1561-23 PCI1561-24 PCI1561-25 PCI1561-26 PCI1561-27 PCI1561-28 PCI1561-29 PCI1561-30 PCI1561-31 PCI1561-32 PCI1561-33 PCI1561-34 9040B471K103LEXH 9040B471M103LEXH 9040B561K103LEXH 9040B561M103LEXH 9040B681K103LEXH 9040B681M103LEXH 9040B821K103LEXH 9040B821M103LEXH 9040B102K103LEXH 9040B102M103LEXH 9040B122K103LEXH 9040B122M103LEXH 9040B152K103LEXH 9040B152M103LEXH 9040B182K103LEXH 9040B182M103LEXH 9040B222K103LEXH 9040B222M103LEXH 9040B272K103LEXH 9040B272M103LEXH 9040B332K103LEXH 9040B332M103LEXH 11050B392K103LEXH 11050B392M103LEXH 11050B472K103LEXH 11050B472M103LEXH 13060B562K103LEXH 13060B562M103LEXH 13060B682K103LEXH 13060B682M103LEXH 13060B822K103LEXH 13060B822M103LEXH 13060B103K103LEXH 13060B103M103LEXH HQHBR471KB HQHBR471MB HQHBR561KB HQHBR561MB HQHBR681KB HQHBR681MB HQHBR821KB HQHBR821MB HQHBR102KB HQHBR102MB HQHBR122KB HQHBR122MB HQHBR152KB HQHBR152MB HQHBR182KB HQHBR182MB HQHBR222KB HQHBR222MB HQHBR272KB HQHBR272MB HQHBR332KB HQHBR332MB HQJBR392KB HQJBR392MB HQJBR472KB HQJBR472MB HQKBR562KB HQKBR562MB HQKBR682KB HQKBR682MB HQKBR822KB HQKBR822MB HQKBR103KB HQKBR103MB Vendor F similar vendor type 100HV14B471KM 100HV14B471MM 100HV14B561KM 100HV14B561MM 100HV14B681KM 100HV14B681MM 100HV14B821KM 100HV14B821MM 100HV14B102KM 100HV14B102MM 100HV14B122KM 100HV14B122MM 100HV14B152KM 100HV14B152MM 100HV14B182KM 100HV14B182MM 100HV14B222KM 100HV14B222MM 100HV14B272KM 100HV14B272MM 100HV14B332KM 100HV14B332MM 100HV15B392KM 100HV15B392MM 100HV15B472KM 100HV15B472MM 100HV16B562KM 100HV16B562MM 100HV16B682KM 100HV16B682MM 100HV16B822KM 100HV16B822MM 100HV16B103KM 100HV16B103MM 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 6 Vendor Vendor CAGE Vendor name and address A 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 B 63980 Wright Capacitors Incorporated 2610 South Oak Street Santa Ana CA 92707-3720 C 60212 Presidio Components Incorporated 7169 Construction Court San Diego CA 92121-2615 D 65238 Novacap 25136 Anza Drive Valencia CA 91355-3415 E 0YBX7 Union Technology Corporation 718 Monterey Pass Road Monterey Park, CA 91754-3607 F 3H3G4 CalRamic Technologies LLC 5462 Louie Lane Reno, NV 89511 DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87081 REV G PAGE 7