REVISIONS DESCRIPTION LTR A Added suggested sources of supply. DATE APPROVED 11 May 88 D. Moore Deleted and added suggested sources of 8 Oct 92 supply. Editorial changes throughout. Added .082 µF in case size F. Updated 21 Jul 93 manufacturers PIN. Editorial changes throughout. Changes to paragraphs 3.2.2, 3.2.6, and 6.1. Added suggested source of supply. Editorial 23 Feb 94 changes throughout. Changes in accordance with NOR 5910-R00623 May 96 96 Revised sources of supply, added alternate marking method, made editorial changes, and 5 April 99 converted references to MIL-PRF-49467. Moved solderability testing from group A to 10 April 00 group B. Updated suggested sources of supply. Removed suggested source of supply. Added note 4 to figure 1. Added capacitor tolerance 16 January 01 note to 3.2.9. Added suggested source of supply. Changed 12 September 01 Johanson Dielectrics CAGE code. Updated name and address of vendor C. 4 November 02 Added Johanson Dielectrics as a suggested 18 August 2004 source of supply. Added CalRamic Technologies as a suggested 19 April 2007 source of supply. Changed drawing type to Source Control with approved sources. Added manufacturer 21 October 2010 eligibility criteria, paragraph 3.14. Added new paragraph 6.3. Added an approved source. B C D E F G H J K L M N D. Moore D. Moore D. Moore A. Ernst J. Crum Kendall A. Cottongim Kendall A. Cottongim Kendall A. Cottongim Kendall A. Cottongim Kendall A. Cottongim Michael A. Radecki Michael A. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES PMIC N/A Source control drawing REV N N N N N N N N N PAGES 1 2 3 4 5 6 7 8 9 PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH Original date of drawing 23 June 1987 CHECKED BY HERALDINE JOHNSON APPROVED BY DAVID E. MOORE SIZE A REV AMSC N/A TITLE CAPACITORS, CERAMIC, MULTILAYER, HIGH VOLTAGE, X7R, 3,000 V DC CODE IDENT. NO. 14933 DWG NO. N PAGE 87047 1 OF 9 5910-E477 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49467 describe the requirements for high voltage multilayer ceramic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87047 | | Drawing number -XX | | Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Test Methods Standard Electronics and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or https://www.assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein (see figure 1). 3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. 3.1.2 Case. Epoxy, conformally coated. 3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 3,000 volts dc. 3.2.2 Dielectric type. X7R. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 2 Case code A B C D E F G H Width (W) .320 .370 .470 .570 .670 .770 1.25 1.45 Sizes (max.) Height Thickness (H) (T) .280 .300 .400 .500 .600 .720 .600 .720 .250 .250 .270 .270 .270 .270 .270 .270 Inches .002 .025 .030 .220 .250 .270 .275 .280 .300 .320 .370 .375 .400 .470 Lead spacing ± .030 (S) .220 .275 .375 .475 .575 .675 1.10 1.30 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. H dimension includes meniscus. 4. S dimension shall be maintained from chip body to end of leads. mm 0.05 0.64 0.76 5.59 6.35 6.86 6.99 7.11 7.62 8.13 9.40 9.53 10.16 11.94 Inches .475 .500 .570 .575 .600 .670 .675 .720 .770 1.10 1.25 1.30 1.45 mm 12.07 12.70 14.48 14.61 15.24 17.02 17.15 18.29 19.56 27.94 31.75 33.02 36.83 FIGURE 1. Case dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 3 3.2.3 Temperature coefficient. ±15 percent. (For MIL-PRF-49467 group B voltage temperature limits use, step a through step d only.) 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25°C. 3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25°C, 500 V dc: 100,000 megohms or 1,000 megohm-microfarad, whichever is less. At +125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage. 3.2.8 Aging rate. -2.0 percent maximum per decade-hour. 3.2.9 Capacitance tolerance. K = ±10 percent, M = ±20 percent. K tolerance parts may be substituted for M tolerance parts, with acquiring activity approval. 3.3 Solderability of terminals. In accordance with MIL-PRF-49467. 3.4 Vibration. In accordance with MIL-PRF-49467. 3.5 Shock. In accordance with MIL-PRF-49467. 3.6 Immersion cycling. In accordance with MIL-PRF-49467. 3.7 Moisture resistance. In accordance with MIL-PRF-49467. 3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.9 Thermal shock. Method 107, MIL-STD-202, test condition B except low temperature is -55°C. 3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.11 Terminal strength. In accordance with MIL-PRF-49467. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. Case codes A and B (at the option of the manufacturer) may be marked as indicated below with full marking on the package. Front Back Last 3 digits of drawing number---- 047 XYZ ------ Manufacturer’s trademark Dash number -------------------------- -49 850 ------ Date code FIGURE 2. Alternate marking method for A and B case codes. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-49467 Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime – VAT. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 4 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. TABLE I. Electrical characteristics DSCC drawing 8704701 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Capacitance Capacitance tolerance Case code K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 100 pF 100 pF 120 pF 120 pF 150 pF 150 pF 180 pF 180 pF 220 pF 220 pF 270 pF 270 pF 330 pF 330 pF 390 pF 390 pF 470 pF 470 pF 560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF 1200 pF 1200 pF 1500 pF 1500 pF 1800 pF 1800 pF 2200 pF 2200 pF 2700 pF 2700 pF 3300 pF 3300 pF DSCC drawing 8704739 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Capacitance Capacitance tolerance Case code 3900 pF 3900 pF 4700 pF 4700 pF 5600 pF 5600 pF 6800 pF 6800 pF 8200 pF 8200 pF .01 µF .01 µF .012 µF .012 µF .015 µF .015 µF .018 µF .018 µF .022 µF .022 µF .027 µF .027 µF .033 µF .033 µF .039 µF .039 µF .047 µF .047 µF .056 µF .056 µF .068 µF .068 µF .082 µF .082 µF .10 µF .10 µF .082 µF K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K B B B B C C C C C C C C C C C C D D D D D D D D E E F F F F G G H H H H F DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 5 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM B545 (Standard Specification for Electrodeposited Coating of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-4709 or DSN 850-4709. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 6 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 REV N DWG NO. 87047 PAGE 1/ DSCC drawing PIN 8704701 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Vendor A similar vendor type Vendor B similar vendor type Vendor C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV02HC101KHA SV02HC101MHA SV02HC121KHA SV02HC121MHA SV02HC151KHA SV02HC151MHA SV02HC181KHA SV02HC181MHA SV02HC221KHA SV02HC221MHA SV02HC271KHA SV02HC271MHA SV02HC331KHA SV02HC331MHA SV02HC391KHA SV02HC391MHA SV02HC471KHA SV02HC471MHA SV02HC561KHA SV02HC561MHA SV02HC681KHA SV02HC681MHA SV02HC821KHA SV02HC821MHA SV02HC102KHA SV02HC102MHA SV02HC122KHA SV02HC122MHA SV02HC152KHA SV02HC152MHA SV02HC182KHA SV02HC182MHA SV02HC222KHA SV02HC222MHA SV02HC272KHA SV02HC272MHA N/A N/A SV03HC392KHA SV03HC392MHA SV03HC472KHA SV03HC472MHA SV05HC562KHA SV05HC562MHA SV05HC682KHA SV05HC682MHA SV05HC822KHA SV05HC822MHA 2020CX101KA302 2020CX101MA302 2020CX121KA302 2020CX121MA302 2020CX151KA302 2020CX151MA302 2020CX181KA302 2020CX181MA302 2020CX221KA302 2020CX221MA302 2020CX271KA302 2020CX271MA302 2020CX331KA302 2020CX331MA302 2020CX391KA302 2020CX391MA302 2020CX471KA302 2020CX471MA302 2020CX561KA302 2020CX561MA302 2020CX681KA302 2020CX681MA302 2020CX821KA302 2020CX821MA302 2020CX102KA302 2020CX102MA302 2020CX122KA302 2020CX122MA302 2020CX152KA302 2020CX152MA302 2020CX182KA302 2020CX182MA302 2020CX222KA302 2020CX222MA302 2020CX272KA302 2020CX272MA302 2020CX332KA302 2020CX332MA302 2520CX392KA302 2520CX392MA302 2520CX472KA302 2520CX472MA302 3530CX562KA302 3530CX562MA302 3530CX682KA302 3530CX682MA302 3530CX822KA302 3530CX822MA302 302H46W101KQ3H 302H46W101MQ3H 302H46W121KQ3H 302H46W121MQ3H 302H46W151KQ3H 302H46W151MQ3H 302H46W181KQ3H 302H46W181MQ3H 302H46W221KQ3H 302H46W221MQ3H 302H46W271KQ3H 302H46W271MQ3H 302H46W331KQ3H 302H46W331MQ3H 302H46W391KQ3H 302H46W391MQ3H 302H46W471KQ3H 302H46W471MQ3H 302H46W561KQ3H 302H46W561MQ3H 302H46W681KQ3H 302H46W681MQ3H 302H46W821KQ3H 302H46W821MQ3H 302H46W102KQ3H 302H46W102MQ3H 302H46W122KQ3H 302H46W122MQ3H 302H46W152KQ3H 302H46W152MQ3H 302H46W182KQ3H 302H46W182MQ3H 302H46W222KQ3H 302H46W222MQ3H 302H46W272KQ3H 302H46W272MQ3H 302H46W332KQ3H 302H46W332MQ3H 302H47W392KQ3H 302H47W392MQ3H 302H47W472KQ3H 302H47W472MQ3H 302H51W562KQ3H 302H51W562MQ3H 302H51W682KQ3H 302H51W682MQ3H 302H51W822KQ3H 302H51W822MQ3H UTC4126-01 UTC4126-02 UTC4126-03 UTC4126-04 UTC4126-05 UTC4126-06 UTC4126-07 UTC4126-08 UTC4126-09 UTC4126-10 UTC4126-11 UTC4126-12 UTC4126-13 UTC4126-14 UTC4126-15 UTC4126-16 UTC4126-17 UTC4126-18 UTC4126-19 UTC4126-20 UTC4126-21 UTC4126-22 UTC4126-23 UTC4126-24 UTC4126-25 UTC4126-26 UTC4126-27 UTC4126-28 UTC4126-29 UTC4126-30 UTC4126-31 UTC4126-32 UTC4126-33 UTC4126-34 UTC4126-35 UTC4126-36 UTC4126-37 UTC4126-38 UTC4126-39 UTC4126-40 UTC4126-41 UTC4126-42 UTC4126-43 UTC4126-44 UTC4126-45 UTC4126-46 UTC4126-47 UTC4126-48 126975-01 126975-02 126975-03 126975-04 126975-05 126975-06 126975-07 126975-08 126975-09 126975-10 126975-11 126975-12 126975-13 126975-14 126975-15 126975-16 126975-17 126975-18 126975-19 126975-20 126975-21 126975-22 126975-23 126975-24 126975-25 126975-26 126975-27 126975-28 126975-29 126975-30 126975-31 126975-32 126975-33 126975-34 126975-35 126975-36 126975-37 126975-38 126975-39 126975-40 126975-41 126975-42 126975-43 126975-44 126975-45 126975-46 126975-47 126975-48 See footnote at end of table. PCI1558-01 PCI1558-02 PCI1558-03 PCI1558-04 PCI1558-05 PCI1558-06 PCI1558-07 PCI1558-08 PCI1558-09 PCI1558-10 PCI1558-11 PCI1558-12 PCI1558-13 PCI1558-14 PCI1558-15 PCI1558-16 PCI1558-17 PCI1558-18 PCI1558-19 PCI1558-20 PCI1558-21 PCI1558-22 PCI1558-23 PCI1558-24 PCI1558-25 PCI1558-26 PCI1558-27 PCI1558-28 PCI1558-29 PCI1558-30 PCI1558-31 PCI1558-32 PCI1558-33 PCI1558-34 PCI1558-35 PCI1558-36 PCI1558-37 PCI1558-38 PCI1558-39 PCI1558-40 PCI1558-41 PCI1558-42 PCI1558-43 PCI1558-44 PCI1558-45 PCI1558-46 PCI1558-47 PCI1558-48 Vendor G similar vendor type Vendor H similar vendor type 2020N101K302LEXH 2020N101M302LEXH 2020N121K302LEXH 2020N121M302LEXH 2020N151K302LEXH 2020N151M302LEXH 2020N181K302LEXH 2020N181M302LEXH 2020N221K302LEXH 2020N221M302LEXH 2020N271K302LEXH 2020N271M302LEXH 2020B331K302LEXH 2020B331M302LEXH 2020B391K302LEXH 2020B391M302LEXH 2020B471K302LEXH 2020B471M302LEXH 2020B561K302LEXH 2020B561M302LEXH 2020B681K302LEXH 2020B681M302LEXH 2020B821K302LEXH 2020B821M302LEXH 2020B102K302LEXH 2020B102M302LEXH 2020B122K302LEXH 2020B122M302LEXH 2020B152K302LEXH 2020B152M302LEXH 2020B182K302LEXH 2020B182M302LEXH 2020B222K302LEXH 2020B222M302LEXH 2020B272K302LEXH 2020B272M302LEXH 2020B332K302LEXH 2020B332M302LEXH 2520B392K302LEXH 2520B392M302LEXH 2520B472K302LEXH 2520B472M302LEXH 3530B562K302LEXH 3530B562M302LEXH 3530B682K302LEXH 3530B682M302LEXH 3530B822K302LEXH 3530B822M302LEXH 30HV02B101KM 30HV02B101MM 30HV02B121KM 30HV02B121MM 30HV02B151KM 30HV02B151MM 30HV02B181KM 30HV02B181MM 30HV02B221KM 30HV02B221MM 30HV02B271KM 30HV02B271MM 30HV02B331KM 30HV02B331MM 30HV02B391KM 30HV02B391MM 30HV02B471KM 30HV02B471MM 30HV02B561KM 30HV02B561MM 30HV02B681KM 30HV02B681MM 30HV02B821KM 30HV02B821MM 30HV02B102KM 30HV02B102MM 30HV02B122KM 30HV02B122MM 30HV02B152KM 30HV02B152MM 30HV02B182KM 30HV02B182MM 30HV02B222KM 30HV02B222MM 30HV02B272KM 30HV02B272MM 30HV02B332KM 30HV02B332MM 30HV03B392KM 30HV03B392MM 30HV03B472KM 30HV03B472MM 30HV04B562KM 30HV04B562MM 30HV04B682KM 30HV04B682MM 30HV04B822KM 30HV04B822MM 7 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A 1/ DSCC drawing PIN 8704749 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Vendor A similar vendor type Vendor B similar vendor type Vendor C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV05HC103KHA SV05HC103MHA SV05HC123KHA SV05HC123MHA N/A N/A SV07HC183KHA SV07HC183MHA SV07HC223KHA SV07HC223MHA SV07HC273KHA SV07HC273MHA N/A N/A SV08HC393KHA SV08HC393MHA SV09HC473KHA SV09HC473MHA SV09HC563KHA SV09HC563MHA SV11HC683KHA SV11HC683MHA SV12HC823KHA SV12HC823MHA SV12HC104KHA SV12HC104MHA N/A 3530CX103KA302 3530CX103MA302 3530CX123KA302 3530CX123MA302 3530CX153KA302 3530CX153MA302 4540CX183KA302 4540CX183MA302 4540CX223KA302 4540CX223MA302 4540CX273KA302 4540CX273MA302 4540CX333KA302 4540CX333MA302 5550CX393KA302 5550CX393MA302 6560CX473KA302 6560CX473MA302 6560CX563KA302 6560CX563MA302 11050CX683KA302 11050CX683MA302 13060CX823KA302 13060CX823MA302 13060CX104KA302 13060CX104MA302 6560CX823KA302 302H51W103KQ3H 302H51W103MQ3H 302H51W123KQ3H 302H51W123MQ3H 302H51W153KQ3H 302H51W153MQ3H 302H62W183KQ3H 302H62W183MQ3H 302H62W223KQ3H 302H62W223MQ3H 302H62W273KQ3H 302H62W273MQ3H 302H62W333KQ3H 302H62W333MQ3H 302H66W393KQ3H 302H66W393MQ3H 302H70W473KQ3H 302H70W473MQ3H 302H70W563KQ3H 302H70W563MQ3H 302H99W683KQ3H 302H99W683MQ3H 302H80W823KQ3H 302H80W823MQ3H 302H80W104KQ3H 302H80W104MQ3H 302H70W823KQ3H UTC4126-49 UTC4126-50 UTC4126-51 UTC4126-52 UTC4126-53 UTC4126-54 UTC4126-55 UTC4126-56 UTC4126-57 UTC4126-58 UTC4126-59 UTC4126-60 UTC4126-61 UTC4126-62 UTC4126-63 UTC4126-64 UTC4126-65 UTC4126-66 UTC4126-67 UTC4126-68 UTC4126-69 UTC4126-70 UTC4126-71 UTC4126-72 UTC4126-73 UTC4126-74 UTC4126-75 126975-49 126975-50 126975-51 126975-52 126975-53 126975-54 126975-55 126975-56 126975-57 126975-58 126975-59 126975-60 126975-61 126975-62 126975-63 126975-64 126975-65 126975-66 126975-67 126975-68 126975-69 126975-70 126975-71 126975-72 126975-73 126975-74 126975-75 PCI1558-49 PCI1558-50 PCI1558-51 PCI1558-52 PCI1558-53 PCI1558-54 PCI1558-55 PCI1558-56 PCI1558-57 PCI1558-58 PCI1558-59 PCI1558-60 PCI1558-61 PCI1558-62 PCI1558-63 PCI1558-64 PCI1558-65 PCI1558-66 PCI1558-67 PCI1558-68 PCI1558-69 PCI1558-70 PCI1558-71 PCI1558-72 PCI1558-73 PCI1558-74 PCI1558-75 Vendor G similar vendor type Vendor H similar vendor type 3530B103K302LEXH 3530B103M302LEXH 3530B123K302LEXH 3530B123M302LEXH 3530B153K302LEXH 3530B153M302LEXH 4540B183K302LEXH 4540B183M302LEXH 4540B223K302LEXH 4540B223M302LEXH 4540B273K302LEXH 4540B273M302LEXH 4540B333K302LEXH 4540B333M302LEXH 5550B393K302LEXH 5550B393M302LEXH 6560B473K302LEXH 6560B473M302LEXH 6560B563K302LEXH 6560B563M302LEXH 11050B683K302LEXH 11050B683M302LEXH 13060B823K302LEXH 13060B823M302LEXH 13060B104K302LEXH 13060B104M302LEXH 6560B823K302LEXH 30HV04B103KM 30HV04B103MM 30HV04B123KM 30HV04B123MM 30HV04B153KM 30HV04B153MM 30HV05B183KM 30HV05B183MM 30HV05B223KM 30HV05B223MM 30HV05B273KM 30HV05B273MM 30HV05B333KM 30HV05B333MM 30HV06B393KM 30HV06B393MM 30HV07B473KM 30HV07B473MM 30HV07B563KM 30HV07B563MM 30HV15B683KM 30HV15B683MM 30HV16B823KM 30HV16B823MM 30HV16B104KM 30HV16B104MM 30HV07B823KM 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. CODE IDENT NO. 14933 REV N DWG NO. 87047 PAGE 8 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address A 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 B 63980 Wright Capacitors Incorporated 2610 South Oak Street Santa Ana CA 92707-3720 C 07EN1 Advanced Monolythic Ceramics, Incorporated 3101 Constitution Avenue, Suite 100 Olean NY 14760-1867 D 0YBX7 Union Technology Corporation 718 Monterey Pass Road Monterey Park CA 91754-3607 E 0LR95 Spectrum Control Technology Incorporated 1900 West College Avenue State College, PA 16801 F 60212 Presidio Components Incorporated 7169 Construction Court San Diego CA 92121-2615 G 65238 Novacap 25136 Anza Drive Valencia CA 91355-3415 H 3H3G4 CalRamic Technologies LLC 5462 Louie Lane Reno, NV 89511 J 29454 Johanson Dielectrics, Inc 15191 Bledsoe Avenue Sylmar, CA 91342 DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87047 REV N PAGE 9