REVISIONS LT DATE 30 March 99 APPROVED Howard H. Jenkins 23 June 04 Kendall Cottongim C DESCRIPTION Add additional part numbers per request of users. Add three percent lead requirement to lead finish paragraph. Add -29 part per request of user 22 December 04 Kendall Cottongim D Add new manufacturer and part numbers. 27 April 05 Kendall Cottongim E Add new manufacturer and part numbers. 18 April 07 Michael Radecki F Add new manufacturer and part numbers 6 June 08 Michael Radecki A B Prepared in accordance with ASME Y14.100-2000 REV STATUS OF PAGES Selected item drawing REV F F F F F F F F F PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Edward H. Back DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 9 August 1995 CHECKED BY Edward H. Back TITLE CAPACITOR, FIXED, TANTALUM CHIP, LOW ESR APPROVED BY David E. Moore CODE IDENT. NO. 037Z3 SIZE A REV F DWG NO. 95158 PAGE 1 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. OF 9 5910-E415 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for low ESR tantalum chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 95158- 01 Drawing number Dash number (see table I) K H Capacitance tolerance K = ±10 percent M = ±20 percent Termination finish B = Gold plated (10 microinch minimum) H = solder plated (100 microinch minimum) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-55365 - Capacitor, Fixed, Electrolytic (Tantalum), Chip, Established Reliability and Nonestablished Reliability, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminations. Chip capacitors shall have gold plated or solder plated terminations (see 1.2 and figure 1). The solder plated terminations shall be solderable when tested in accordance with MIL-STD-202, method 208. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is three percent. 3.1.2 Operating temperature range. The capacitors are rated for their given voltages from -55°C to +85°C. They are derated two thirds of their given voltages at +125°C. See table I. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 2 Dimensions Case code C D X L ± 0.3 (± .012) 6.0 (.236) 7.3 (.287) 7.3 (.287) H ± 0.3 (± .012) 2.5 (.098) 2.8 (.110) 4.0 (.157) W ± 0.3 (± .012) 3.2 (.126) 4.3 (.169) 4.3 (.169) Dimensions (reference only) (see note 7) Case code C D X K ± 0.20 (± .008) 1.4 (.055) 1.5 (.059) 2.3 (.091) S ± 0.3 (± .012) 1.3 (.051) 1.3 (.051) 1.3 (.051) F ± 0.1 (± .004) 2.2 (.087) 2.4 (.094) 2.4 (.094) B ± 0.15 (± .006) 0.5 (.020) 0.5 (.020) 0.5 (.020) X ± 0.10 (± .004) 0.10 (.004) 0.10 (.004) 0.10 (.004) Dimensions (reference only) (see note 7) Case code C D X P 0.9 (.035) 0.9 (.035) 1.7 (.067) R 1.0 (.039) 1.0 (.039) 1.0 (.039) A 3.1 (.122) 3.8 (.150) 3.8 (.150) T 0.13 (.005) 0.13 (.005) 0.13 (.005) G 2.8 (.110) 3.5 (.138) 3.5 (.138) See note 6 E 2.4 (.094) 3.5 (.138) 3.5 (.138) See note 6 DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 3 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are in parentheses and are given for information only. 3. The anode (+) terminal shall be indicated by the bevel on the anode end. 4. Solderable surfaces are only those surfaces designated as such. Termination edges are not considered solderable. 5. Notch at option of the manufacturer. 6. At the option of the manufacturer, this area may be a round glue pad, 2.9 ± 0.1 (.114 ± .004) in diameter. 7. Reference dimensions may vary by manufacturer. Contact manufacturer for exact dimensions. FIGURE 1. Dimensions and configuration. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 4 TABLE I. Electrical characteristics. DSCC drawing 951581/ Dissipation factor (max) % DC leakage (max) uA Cap. (nom) uF +25°C +85°C +25°C +125°C 4 V dc at 125°C 6 V dc at 85°C +85°C +125°C Max ESR 100 kHz +25°C Ohms Case code -55°C 8 V dc surge at 85°C 01-02-03-25-- 68 150 220 220 10 V dc at 85°C 3.3 7.2 13.2 13.2 19.8 43.2 132 132 4 33 6 72 8 165 8 165 7 V dc at 125°C 6 8 12 12 0.175 6 0.125 8 0.100 12 0.100 12 13 V dc surge at 85°C D X X D 04-05-06-07-08-26-28-- 47 68 100 100 150 150 220 16 V dc at 85°C 3.8 5.4 10 8 15 15 15 22.8 32.4 100 48 150 150 150 4 38 4 54 8 125 6 80 8 187.5 8 187.5 8 187.5 10 V dc at 125°C 6 6 12 8 12 12 12 0.200 6 0.150 6 0.100 12 0.100 8 0.100 12 0.100 12 0.100 12 20 V dc surge at 85°C D X D X X D X 09-10-11-- 4.2 33 7.5 47 16 100 20 V dc at 85°C 25.2 75 160 4 42 6 94 8 200 13 V dc at 125°C 6 9 12 0.250 6 0.200 9 0.125 12 26 V dc surge at 85°C D D X 12-13-14-15-- 15 22 47 68 25 V dc at 85°C 2.4 3.5 7.5 13.6 14.4 21 45 136 4 24 4 35 4 75 6 170 17 V dc at 125°C 6 6 6 9 0.275 6 0.275 6 0.150 6 0.150 9 32 V dc surge at 85°C D D X X 16-17-18-19-- 15 15 22 33 35 V dc at 85°C 3.8 3 4.4 6.6 38 18 26.4 39.6 6 46.9 4 30 4 44 4 66 23 V dc at 125°C 9 6 6 6 0.275 9 0.200 6 0.225 6 0.175 6 46 V dc surge at 85°C D X X X 29-20-27-21-22-23-- 4.7 6.8 10 10 15 22 50 V dc at 85°C 1.7 1.9 3.5 2.8 5.3 7.7 10.2 11.4 35 16.8 53 77 6 17 4 19 4 42 4 28 6 65.6 6 96.3 33 V dc at 125°C 9 6 6 6 9 9 0.600 9 0.300 6 0.300 6 0.250 6 0.225 9 0.300 9 65 V dc surge at 85°C C X D X X X 1.9 11.4 24-- 4.7 19 4 6 6 0.300 X DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 5 3.2 Electrical characteristics. 3.2.1 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202. Maximum dc bias shall be 2.2 volts for all ac measurements. The frequency of the ac voltage shall be 120 ± 5 Hz and the magnitude shall be limited to 1.0 volt rms. 3.2.2 Capacitance tolerance. K = ±10 percent, M = ±20 percent. 3.2.3 Rated voltage. The rated voltage shall be in accordance with table I. Above +85°C, voltage derating is required (see MIL-PRF-55365). 3.3 Surge current. Surge current shall be performed on a 100 percent basis before or after the group A (exponential distribution) voltage aging test of MIL-PRF-55365. Capacitors shall be subjected to four consecutive cycles under the following conditions: a. Temperature: +25°C ±5°C. b. Applied voltage: Rated dc voltage ±2 percent from a power source having an energy storage bank of 50,000 uF (minimum) across the output terminals. c. Charge cycle: 4 seconds maximum. d. Discharge cycle: 4 seconds maximum to a voltage below 1 percent of rated voltage. e. The total dc resistance (excluding the capacitor) including the wiring, fixturing, and output impedance of the regulated power supply to each test position during the charging cycle shall be 0.6 ohm maximum. f. On completion of the test, the capacitors shall meet the following requirements: DCL: See table I. Cap.: Shall meet the initial measured value. DF: See table I. 3.4 Additional tests. The following additional tests shall be performed at the option of the user (see 6.2b) and shall be negotiable with the manufacturer. 3.4.1 Vibration, high frequency. The capacitors shall meet the requirements of MIL-PRF-55365 when tested in accordance with test condition D, method 204 of MIL-STD-202. 3.4.2 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-55365 when tested for five cycles. 3.4.3 Solderability. Solderability shall be in accordance with MIL-PRF-55365. 3.4.4 Surge voltage. Surge voltage shall be in accordance with MIL-PRF-55365. 3.4.5 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-55365. 3.4.6 Stability at low and high temperatures. Stability at low and high temperatures shall be in accordance with MIL-PRF-55365. 3.4.7 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-55365. 3.4.8 Life. A minimum of dc rated voltage at 85°C or a minimum of derated voltage per MIL-PRF-55365 at 125°C for 2000 hours. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a approved source of supply. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 6 3.7 Marking. Marking shall be in accordance with MIL-PRF-55365, except the "JAN" or "J" brand and the failure rate level symbol do not apply and shall not be marked on the capacitor or any packaging. 3.8 Workmanship. Capacitors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the surge current test and the group A inspection (exponential distribution), subgroups 1 and 3, of MIL-PRF-55365, except that the voltage aging shall be for a minimum of 10 hours. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CDROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-0563 or DSN 850-0563. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 7 6.4 Similar vendor types. See table II. TABLE II. Similar vendor types. DSCC drawing 9515801-02-03-04-05-06-07-08-09-10-11-12-13-14-15-16-17-18-19-20-21-22-23-24-25-26-27-28-29-- Similar vendor PIN A 1/ T495D686-006AT495X157-006AT495X227-006AT495D476-010AT495X686-010AT495D107-010AT495X107-010AT495X157-010AT495D336-016AT495D476-016AT495X107-016AT495D156-020AT495D226-020AT495X476-020AT495X686-020AT495D156-025AT495X156-025AT495X226-025AT495X336-025AT495X685-035AT495X106-035AT495X156-035AT495X226-035AT495X475-050AT495D227-006AT495D157-010AT495D106-035AT495X227-010AT495C475-035A- Similar vendor PIN B 1/ 593D686X-6R3D593D157X-6R3E593D227X-6R3E593D476X-010D593D686X-010E593D107X-010D593D107X-010E593D157X-010E593D336X-016D593D476X-016D593D107X-016E593D156X-020D593D226X-020D593D476X-020E593D686X-020E593D156X-025D593D156X-025E593D226X-025E593D336X-025E593D685X-035E593D106X-035E593D156X-035E593D226X-035E593D475X-050E593D227X-6R3D593D157X-010D593D106X-035D593D227X-010E593D475X-035C- Similar vendor PIN C 1/ TBJD686-006C-DZ0-23 TBJE157-006C-DZ0-23 TBJE227-006L-DZ0-23 TBJD476-010C-DZ0-23 TBJE686-010C-DZ0-23 TBJD107-010C-DZ0-23 TBJE107-010C-DZ0-23 TBJE157-010C-DZ0-23 TBJD336-016C-DZ0-23 TBJD476-016C-DZ0-23 TBJE107-016C-DZ0-23 TBJD156-020C-DZ0-23 TBJD226-020C-DZ0-23 TBJE476-020C-DZ0-23 TBJE686-020L-DZ0-23 TBJD156-025C-DZ0-23 N/A TBJE226-025L-DZ0-23 TBJE336-025C-DZ0-23 N/A TBJE106-035C-DZ0-23 TBJE156-035C-DZ0-23 TBJE226-035C-DZ0-23 N/A TBJD227-006L-DZ0-23 TBJD157-010C-DZ0-23 TBJD106-035C-DZ0-23 TBJE227-010C-DZ0-23 TBJC475-035C-DZ0-23 1/ Caution. Do not use this number for item acquisition and marking. The similar vendor type may not satisfy the performance requirements of this drawing. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 8 6.5 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-0563 or DSN 850-0563. DSCC drawing PIN Vendors similar designation or type number 1/ Vendor CAGE 95158-**** A 31433 KEMET Electronics Corporation P.O. Box 5928 Greenville SC 29606-0647 95158-**** B SH905 95158-**** C 17554 Vishay Israel Ltd. P.O. Box 87 Industrial Park Dimona 86100, Israel AVX Tantalum Corp. 401 Hill St. Biddeford, ME 04005 1/ Vendor's name and address Caution: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 037Z3 95158 REV F PAGE 9