REVISIONS LTR DESCRIPTION DATE APPROVED A Changed manufacturer's eligibility. 24 August 87 S. Searcy B Added vendor CAGE 31757 as an approved source. Editorial changes throughout. 7 May 92 D. Moore C Changes in accordance with NOR 5945-R003. 2 Mar 00 K. Cottongim D Validation and update. 17 Sep 03 K. Cottongim E Technical change to paragraph 3.4.7. 10 Dec 03 K. Cottongim CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV PAGE REV STATUS OF PAGES PMIC N/A REV E D D E D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PREPARED BY James R. Martin Original date of drawing CHECKED BY Richard A. Yannitti 13 January 1986 APPROVED BY Steven B. Searcy SIZE A REV DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 TITLE RELAYS, SOLID STATE, OPTICALLY ISOLATED, HERMETICALLY SEALED, ANALOG SIGNAL SWITCHING, SPST (N.O.), CMOS AND TTL CONTROL INPUTS, 1 AMPERE, 60 V DC MAXIMUM CODE IDENT. NO. 14933 DWG NO. E PAGE 86001 1 OF AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 12 5945-E119 1. SCOPE 1.1 Scope. This drawing describes the requirements for a sealed solid-state relay supplied to "Y" screening requirements of MIL-PRF-28750. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: -001 | | Dash number 86001 | | Drawing number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.3). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-PRF-28750 - Relays, Solid State, Sealed, General Specification For. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 MIL-STD-750 MIL-STD-883 - Test Method Standard Electronic and Electrical Component Parts. Test Method Standard for Semiconductor Devices. Test Method Standard Microcircuits. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-28750, and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28750 and herein (see figure 1). DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 2 3.3 Input characteristics. 3.3.1 Five terminal/CMOS input control. See figure 1. 3.3.1.1 Bias voltage. 3.8 to 32 V dc (see table I). 3.3.1.2 Bias current. 16 mA maximum. TABLE I. Series control/bias resistor selection. 1/ VC range Rs Ohms 3.86V 6.010 V 1014 V 1418 V 1822 V 2226 V 2632 V 300 620 910 1,200 1,500 2,000 1/4 1/4 1/2 1/2 1/2 1 Not required Power rating watts 1/ Limiting resistor required over 6.0 volts when not used with a heat sink; with a heat sink, the values are to be determined. 3.3.1.3 Control current. 250 microamperes maximum at 5 V dc control voltage. 3.3.1.4 Control turn-off voltage. 2.8 V dc minimum at +25°C to +100°C. 3.3.1.4.1 Control turn-off voltage. 3.2 V dc minimum (-55°C to +25°C). 3.3.1.5 Control turn-on voltage. 0.5 V dc maximum at -55°C to +25°C. 3.3.1.5.1 Control turn-on voltage. 0.3 V dc maximum (+25°C to +100°C). 3.3.1.6 Schmitt hysteresis. 0.7 V dc minimum. 3.3.1.7 Control voltage range. 0 V dc to 18 V dc. 3.3.2 Four terminal/TTL input control. See figure 1. 3.3.2.1 Input current. 16 milliamperes. 3.3.2.2 Control voltage range. 3.8 V dc to 6 V dc TTL mode. 3.8 V dc to 32 V dc terminal mode (see table I). 3.3.2.3 Control turn-off voltage. 1.5 V dc maximum. 3.3.2.4 Control turn-on voltage. 3.8 V dc minimum. 3.4 Output characteristics. 3.4.1 Output voltage. 60 V dc maximum. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 3 3.4.2 On-state resistance. 0.35 ohm maximum (measured at 100 mA at 25°C). NOTE: For on-state resistance at temperatures other than +25°C, use the following equation: (0.006 x ∆T) R = R25 x e Where: R25 = resistance at +25°C from table I. R = resistance at new temperature. ∆T = (T -25°C). e = 2.7182818. 3.4.3 Load current. 1.0 ampere maximum at +25°C (see figure 2). 3.4.4 Turn-on time (tON). 2.2 milliseconds maximum at -55°C to +25°C. 3.0 milliseconds maximum at +25°C to +100°C (see figure 3). 3.4.5 Turn-off time (tOFF). 3.0 milliseconds maximum (see figure 3). 3.4.6 Output voltage drop. 0.6 volt maximum (at rated current). 3.4.7 Off-state leakage. 10 microamperes maximum at 60 V dc. 3.4.8 Transient voltage. 80 V dc maximum for 2 seconds maximum, single pulse. 3.4.9 Exponential rate of voltage rise (dv/dt). Not applicable. 3.5 Electrical characteristics. 3.5.1 Insulation resistance. Input to output Input to case 1,000 megohms minimum. Output to case 3.5.2 Dielectric strength. Input to output Input to case 1,000 V rms minimum. Output to case 3.5.3 Reverse polarity. Applicable. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 4 FIGURE 1. Outline drawing and dimensions. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 5 FIGURE 1. Outline drawing and dimensions - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 6 Inches .001 .002 .017 .031 .032 .080 .085 .100 .200 .275 .335 .370 .700 mm 0.03 0.05 0.43 0.79 0.81 2.03 2.16 2.54 5.08 6.99 8.51 9.40 17.78 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers shown above are for reference only. 5. Loads may be connected to either terminal 7, terminal 1, or both (split loads). 6. See table I for value of RS when VC > 6 V. FIGURE 1. Outline drawing and dimensions - Continued. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 7 FIGURE 2. Output current vs ambient temperature. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 8 NOTES: 1. tON + TdON + tr. 2. tOFF + TdOFF + tf. 3. Input transition should be < 1.0 ms. FIGURE 3. Turn-on and turn-off time waveform. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 9 3.6 ENVIRONMENTAL DATA 3.6.1 Operating temperature range. -55°C to maximum per thermal operating curve (see figure 2). 3.6.2 Storage temperature range. -55°C to +125°C. 3.6.3 Shock. MIL-STD-202, method 213, test condition F, (1,500 g's for 0.5 ms, 1/2 sine wave). 3.6.4 Vibration. MIL-STD-202, method 204, test condition D, 100 g's, 10 to 3,000 Hz. 3.6.5 Seal. Hermetic, in accordance with MIL-PRF-28750. 3.6.6 Resistance to soldering heat. Applicable. 3.6.7 Salt spray (atmosphere). MIL-STD-750, method 1041. 3.6.8 Acceleration. MIL-STD-883, method 2001, test condition A, 5,000 g's, Y1 axis. 3.6.9 Electromagnetic interference. Not applicable. 3.6.10 Moisture resistance. Not applicable. 3.6.11 Overload. Applicable. 3.7 Physical. Physical requirements shall be as specified herein. 3.7.1 Weight. 2 grams maximum (.07 ounce). 3.7.2 Dimensions and configuration. See figure 1. 3.8 Marking. Marking shall be in accordance with MIL-PRF-28750, except the PIN shall be in accordance with 1.2 herein. The “M28750/X-XXXY” PIN shall not be used. 3.9 Conformance requirements. Relays furnished under this drawing shall have been subjected to, and passed all the requirements, tests, and inspections detailed herein. 3.9.1 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-28750 and 4.2 herein. 3.10 Certification as an approved source of supply. In order to be listed as an approved source of supply for relays manufactured to this drawing, a manufacturer shall: a. Agree to make available to DSCC, upon request, all pertinent test data on its production of the subject part, including, but not limited to, test data in accordance with the qualification inspection table of MIL-PRF-28750, Y screening level. b. Provide to DSCC or its designated agent, upon request, free of charge and without obligation, a current production sample from its production of the subject part. c. Meet one of the following criteria: (1) Currently possess listing on qualified products list QPL-28750 for at least one part. (2) Be in current production of the subject part. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 10 3.12 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.13 Workmanship. The relays shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling and inspection procedures shall be performed in accordance with MIL-PRF-28750, except as modified herein. 4.2 Conformance inspection. Conformance inspection shall be in accordance with group A listing of MIL-PRF-28750. Group A testing shall be performed on each inspection lot and manufacturers shall keep lot records for 3 years (minimum), monitor for compliance to the prescribed procedures, and observe that satisfactory manufacturing conditions and records on lots are maintained for these relays. 4.2.1 Group A inspection. Group A inspection shall consist of all tests specified in MIL-PRF-28750 for the "Y" screening level except internal components used internally to the relay shall not require hermetic packaging. Temperature range shall be as specified in 3.6.1. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Department or Defense Agency, or within the Military Department's System Command. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Notes. Only definitions of the notes specified in MIL-PRF-28750 will apply to this drawing. 6.2 Intended use. Relays conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL28750; this drawing will become inactive for new design. The QPL-28750 product shall be the preferred item for all applications. 6.3 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.4 Replaceability. Relays covered by this drawing will replace the same generic device covered by a contractor prepared specification or drawing. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 11 6.5 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43216-5000 or by telephone (614) 692-0554 or DSN 850-0554. 6.6 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000 or by telephone (614) 692-0554 or DSN 850-0554. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 86001-001 690-2Y 16170 Teledyne Microelectronic Technologies 12964 Panama Street Los Angeles, CA 90066-6534 Phone: (310) 822-8229 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE CODE IDENT NO. DWG NO. A 14933 86001 REV E PAGE 12