LTM4601 DC/DC Module Thermal Performance

Application Note 110
May 2007
LTM4601 DC/DC µModule® Regulator Thermal
Performance
Eddie Beville, Jian Yin
INTRODUCTION
The LTM4601 DC/DC μModule regulator is a complete
high power density stepdown regulator for up to 12A
continuous (14A peak) loads. The device is housed in
a small 15mm ¥ 15mm ¥ 2.8mm LGA surface mount
package, thus the large power dissipation is a challenge
in some applications. This thermal application note will
provide guidelines for using the μModule regulator in
ambient environments with or without air flow. Load
current derating curves are provided for several input
voltages and output voltages versus ambient temperature
and air flow. These derating curves provide guidelines
for using the LTM4601 in ambient environments with
regard to safe-operating-area (SOA). Also included are
efficiency curves that are used to extrapolate the power
loss curves used in this thermal application note. The approach is to measure the temperature of a design, derive
thermal models for different cases and finally determine
the junction-to-ambient thermal resistance (qJA) in units of
°C/W in the heat path. The data includes power loss curves,
safe operating curves (SOA), thermal camera images and
current derating curves versus ambient temperature and
air flow with and without a heatsink. 24V input designs
are analyzed for a worse case temperature rise due to the
relatively lower efficiency exhibited.
THERMAL MODEL
The thermal model is shown in Figure 1. A μModule
regulator is attached to a 4-layer PCB with a size of
95mm ¥ 76mm. To analyze this physical system, a simplified 1- D thermal model presented in Figure 1(b), is
employed to show the heat paths in the system. The heat
is generated from the μModule regulator and flows to the
top and bottom sides. For the topside heat path, RJT is used
to represent the thermal resistance from the junction to the
top package surface, while RTA represents the resistance
from the top package surface to ambient. Similarly, for
the bottom side, RJB is the thermal resistance from the
junction to the bottom surface, and RBA is the resistance
from the bottom surface to ambient. The double-sided
cooling scheme can be realized easily, especially if a heat
sink is used for the top side.
L, LT, LTC, LTM, Linear Technology, μModule and the Linear logo are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective owners.
TA
RTA
RJT
μModule REGULATOR
PCB
RJB
RJT
RTA
TJ
RBA
TA
(a)
TA
RJB
RBA
(b)
AN110 F01
Figure 1. Design Thermal Model
an110fa
AN110-1
Application Note 110
THERMAL IMAGING
the regulator with 4.2W of dissipation in the design, and
Figure 3 has a maximum temperature of 100°C on the
μModule regulator with 5.8W of dissipation.
Case 1: No Heatsink
A 12VIN to 3.3VOUT at 12A design and a 24VIN to 3.3VOUT at
12A design are characterized for 39.6W operation at 91% and
87% conversion efficiency, respectively. This corresponds
to a power loss of about 4.2W and 5.8W dissipated from
the power module. The extra 4% loss on the 24V design is
attributed to the extra power dissipation in the controller, and
increased transition losses in the internal top MOSFET. This
loss can be reduced by about 2%, or an efficiency of 89%
from the 24VIN design, by connecting the DRVCC pin to a 5V
bias supply with a 50mA capability. The DRVCC voltage must
be supplied after the main input supply. Figure 2 shows a
thermal image of the 12VIN to 3.3VOUT design with several
thermal image data points, and Figure 3 shows the 24VIN
to 3.3VOUT design with several thermal image data points.
The maximum temperature in Figure 2 is equal to 85°C on
For a worse case with no heatsink and 5.8W of dissipation
in Figure 3, the heat dissipation from the package topside
can be ignored. So the thermal model shown in Figure 1 can
be redrawn as in Figure 4, with only thermal resistances RJB
and RBA at the bottom side heat path. Refer to Application
Note 103, the total thermal resistance from junction to
ambient in this case is only 14.3°C/W. Therefore, the
junction temperature of the μModule regulator is 108°C.
CONDITIONS: 25°C AMBIENT, NO AIR FLOW,
NO HEATSINK, NO EXTVCC
CONDITIONS: 25°C AMBIENT, NO AIR FLOW,
NO HEATSINK, NO EXTVCC
Figure 2. LTM4601 12VIN to 3.3VOUT at 12A, Top View
Figure 3. LTM4601 24VIN to 3.3VOUT at 12A, Top View
RJB: 3.5
TJ
RBA: 10.8
Case 2: With A BGA Heatsink
Figure 5 shows a side view thermal image with a surface
mount BGA heatsink mounted on top of the module.
Data point 3 indicates the heatsink temperature, and
data point 2 indicates the side temperature of the power
UNIT: 1°C/W
TA
AN110 F04
Figure 4. Thermal Model for Case 1 in Figure 3
CONDITIONS: 25°C AMBIENT, NO AIR FLOW,
WAKEFIELD ENGINEERING PN#LTN20069
15mm s 15mm s 9mm HEATSINK, NO EXTVCC
Figure 5. LTM4601 24VIN to 3.3VOUT at 12A, Side View
an110fa
AN110-2
Application Note 110
module. The topside of the LTM4601 is very effective in
transferring heat into an external heatsink due to the planar
surface and the case material used. The thermal model,
which represents the configuration in Figure 5 with 5.8W
of dissipation, is shown in Figure 6. In this case, the heat
flows to both top and bottom sides. For the topside heat
path, the heat generated from the module first flows from
the junction (RJH) to the case/heatsink interface, and then it
reaches the heatsink and dissipates into ambient air (RHA).
For the bottom side heat path, the heat first flows to the
4-layer PCB before it dissipates to the ambient air from
the PCB. Here, RJB is the thermal resistance from junction
to PCB dissipation surface and it includes RJP(junction to
module pin) and RPB (pin to PCB dissipation surface).
Since the heat sink temperature is about 74°C in Figure
5 and RHA under natural convection conditions can be
obtained at about 30°C/W from the datasheet of the
manufacturer, the power dissipation to topside is about
1.6W. So the junction temperature in this situation is about
95°C. Compared to the situation without a heatsink in
Figure 4, the heat spreading area to the bottom side
becomes smaller due to lower heat dissipation to the
bottom side, so the thermal resistances in the bottom
side heat path become larger as shown in Figure 6(b).
The total junction-to-ambient thermal resistance for this
scenario with a BGA heatsink is about 12°C/W.
Case 3: With A Metal Plate
Figure 7 shows the side view thermal image of a LTM4601
that is mounted to a metal plate with a size of 100mm ×
75mm. This thermal test case is analyzed for consideration
of use in systems that desire back side PCB mounting of
the power module. The μModule regulator can then be
mounted to a metal carrier either directly or through a
thermal conductive pad.
This case uses a Bergquist “Gap Pad” for the thermal
connection between the power module and metal carrier.
The conditions are noted in Figure 7.
TA
RHA
HEATSINK
μModule REGULATOR
PCB
RJH
RJB
RBA
RJH: 12.8
RHA: 30.0
UNIT: °C/W
TA
TJ
RJB: 4.7
TA
(a)
RBA: 12.0
(b)
AN110 F06
Figure 6. Thermal Model for Case 2 in Figure 5
CONDITIONS: 24V TO 3.3V AT 12A, 25°C AMBIENT, NO AIR FLOW,
A BERGQUIST "GAP PAD 1000" IS USED BETWEEN THE
μModule REGULATOR AND THE METAL PLATE. 0.04 THICKNESS 2°C/W.
(METAL PLATE = 100mm s 75mm s 1.5mm)
Figure 7. LTM4601 24VIN to 3.3VOUT at 12A, Side View
an110fa
AN110-3
Application Note 110
Figure 8 shows the metal plate view of the 40W design
with the conditions noted below in the photo. The metal
plate transfers heat effectively, and would provide an even
better result with air flow. Similar to previous analysis,
the average temperature of the metal plate is about 47°C
(Figure 8). The thermal resistance RMA from the metal
plate to ambient is only about 10.5°C/W due to the large
dissipation surface of the metal plate. Using the thermal
model in Figure 9, we can get the junction temperature
at about 87°C.
There is a thermal resistance drop from the top of the
package to the metal plate. The Bergquist “Gap Pad” that
is used between the package and the metal plate has a
thermal resistance of 2°C/W. The other 5°C/W thermal
resistance drop is developed by the interface of the module
package and metal plate to the “Gap Pad”. This total thermal
resistance drop can be reduced by an improved thermal
interface from the package to the metal plate. Here, RJM
is the total thermal resistance from junction to metal plate
and it includes the thermal resistances from the junction
to the dissipation surface of the metal plate: RJC (junction
to case), RPAD (gap pad), RINTERFACE (interfaces of case
and metal plate to gap pad) and RMETALPLATE (metal
plate). We can obtain all thermal resistances as shown in
Figure 9(b). Similar to case 2, the thermal resistance from
junction to board RJB includes two thermal resistances: RJP
(junction to module pin) and RPB (pin to PCB dissipation
surface). In these thermal resistances, only RJC (6°C/W
to 9°C/W) and RJP (1.5°C/W to 3°C/W) are dependent on
the μModule regulator and all other thermal resistances
are related to specific customer designs. The total thermal
resistance from junction to ambient in this situation is
about 10.7°C/W.
CONDITIONS: 24VIN TO 3.3VOUT AT 12A, 25°C AMBIENT, NO AIR FLOW,
A BERGQUIST "GAP PAD 1000" IS USED BETWEEN THE
μModule REGULATOR AND THE METAL PLATE. 0.04 THICKNESS 2°C/W.
(METAL PLATE = 100mm s 75mm s 1.5mm)
Figure 8. LTM4601 24VIN to 3.3VOUT at 12A, Metal Plate View
METAL PLATE
TA
RMA
RJM
μModule REGULATOR
PCB
RJB
RBA
RJM: 19.0
RMA: 10.5
UNIT: °C/W
TA
TJ
RJB: 4.65
RBA: 12.0
TA
(a)
(b)
AN110 F09
Figure 9. Thermal Model for Case 3 in Figure 7
an110fa
AN110-4
Application Note 110
DERATING CURVES VERSUS AMBIENT TEMPERATURE
AND AIR FLOW
Several derating curves are shown to provide a guideline
for the maximum load current that can be achieved at
certain ambient temperatures. These curves are characterized with 0LFM, 200LFM, and 400LFM air flow. Also
the curves are provided with and without heatsinks. The
power loss curves establish an approximate qJA for the
characterized operating conditions that correlates to the
thermal images above. The power loss curves and derating
curves are used to build a table to correlate qJA versus
air flow. We have chosen 5V, 12V, and 24V as the input
operating conditions for this analysis. The two output
voltages are 1.5V and 3.3V.
Figures 10 and 11 show the 1.5VOUT and 3.3VOUT power
loss curves versus load current and input voltages.
Figures 12, 13, and 14 are the three derating curves for
5VIN to 1.5VOUT versus load current and air flow, with and
without heatsinks. Figures 15, 16, and 17 are the same
derating curves for 12VIN to 1.5VOUT. Figures 18, 19, and
20 are the derating curves for 24VIN to 1.5VOUT. All of
the curves are put into columns to designate the type of
heatsink used in the test conditions.
Figures 21, 22 and 23 are the three derating curves for
12VIN to 3.3VOUT at different load currents, different air
flow, and different heatsinks. Figures 24, 25, and 26 are
the three derating curves for 24VIN to 3.3VOUT. All of
these curves are put into columns to designate the type
of heatsink used in the test conditions.
The power loss curves in Figures 10 and 11 are used in
conjunction with the load current derating curves in Figures
12 through 26 to calculate an approximate qJA. In each
of the load current derating curves, the maximum load
current is shown as a function of the increased ambient
temperature to keep the case temperature of the power
module at 100°C maximum. This 100°C maximum is to
allow for a rise of about 13°C to 20°C inside the module
with a thermal resistance RJC from junction to case at
6°C/W to 9°C/W, maintaining the maximum junction
temperature below 125°C.
CONCLUSION
The LTM4601 thermal models were taken with no air
flow for three cases: no heat sink, a BGA heat sink and
a metal plate. The approximate qJA was then empirically
derived, resulting in values of 14.3°C/W, 12.1°C/W, and
10.7°C/W with no heatsink, a BGA heatsink, and a metal
plate respectively. This data correlates very well with the
zero air flow qJA in Table 2.
an110fa
AN110-5
Application Note 110
6
4
3
2
4
3
2
1
1
0
12VIN LOSS
24VIN LOSS
5
POWER LOSS (W)
5
POWER LOSS (W)
6
5VIN LOSS
12VIN LOSS
24VIN LOSS
VOUT = 1.5V
0
2
4
6
8
LOAD CURRENT (A)
10
0
12
VOUT = 3.3V
0
2
4
6
8
LOAD CURRENT (A)
10
AN110 F11
AN110 F10
Figure 10. Power Loss vs
Load Current
8
6
4
0LFM
200LFM
400LFM
0
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
10
8
6
4
0
100
0LFM
200LFM
400LFM
2
50
AN110 F12
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
8
6
4
0
12
VIN = 12V
VOUT = 1.5V
0LFM
200LFM
400LFM
2
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
6
4
2
100
100
0LFM
200LFM
400LFM
50
Figure 14. Metal Plate with
Gap Pad at 5VIN and 1.5VOUT
10
8
6
4
0LFM
200LFM
400LFM
2
0
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
12
VIN = 12V
VOUT = 1.5V
10
8
6
4
0LFM
200LFM
400LFM
2
0
100
AN110 F16
Figure 16. BGA Heatsink
with 12VIN and 1.5VOUT
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
AN110 F14
VIN = 12V
VOUT = 1.5V
AN110 F15
Figure 15. No Heatsink
with 12VIN and 1.5VOUT
8
Figure 13. BGA Heatsink
with 5VIN and 1.5VOUT
10
VIN = 5V
VOUT = 1.5V
AN110 F13
Figure 12. No Heatsink
with 5VIN and 1.5VOUT
12
10
0
60
70
80
90
AMBIENT TEMPERATURE (°C)
MAXIMUM LOAD CURRENT (A)
2
12
VIN = 5V
VOUT = 1.5V
MAXIMUM LOAD CURRENT (A)
10
Figure 11. Power Loss vs
Load Current
12
VIN = 5V
VOUT = 1.5V
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
12
12
50
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
AN110 F17
Figure 17. Metal Plate with
Gap Pad at 12VIN and 1.5VOUT
an110fa
AN110-6
Application Note 110
8
6
4
0LFM
200LFM
400LFM
60
80
AMBIENT TEMPERATURE (°C)
8
6
4
0
100
0LFM
200LFM
400LFM
2
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
12
VIN = 12V
VOUT = 3.3V
10
8
6
4
0
0LFM
200LFM
400LFM
40
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
10
6
4
0LFM
200LFM
400LFM
2
0
100
50
60
70
80
90
AMBIENT TEMPERATURE (°C)
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
12
8
6
4
0LFM
200LFM
400LFM
20
40
60
80
AMBIENT TEMPERATURE (°C)
VIN = 12V
VOUT = 3.3V
10
8
6
4
0LFM
200LFM
400LFM
2
0
100
50
AN110 F23
100
12
6
4
0LFM
200LFM
400LFM
2
0
0
20
40
60
80
AMBIENT TEMPERATURE (°C)
100
VIN = 24V
VOUT = 3.3V
10
8
6
4
0LFM
200LFM
400LFM
2
0
0
100
20
40
60
80
AMBIENT TEMPERATURE (°C)
AN110 F26
AN110 F25
Figure 25. BGA Heatsink
with 24VIN and 3.3VOUT
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
Figure 23. Metal Plate with
Gap Pad at 12VIN and 3.3VOUT
8
AN110 F24
Figure 24. No Heatsink
with 24VIN and 3.3VOUT
12
VIN = 24V
VOUT = 3.3V
10
100
60
70
80
90
AMBIENT TEMPERATURE (°C)
AN110 F22
VIN = 24V
VOUT = 3.3V
0
50
Figure 22. BGA Heatsink
with 12VIN and 3.3VOUT
10
0
0LFM
200LFM
400LFM
2
Figure 20. Metal Plate with
Gap Pad at 24VIN and 1.5VOUT
8
Figure 21. No Heatsink
with 12VIN and 3.3VOUT
2
4
AN110 F20
VIN = 12V
VOUT = 3.3V
AN110 F21
12
6
Figure 19. BGA Heatsink
with 24VIN and 1.5VOUT
Figure 18. No Heatsink
with 24VIN and 1.5VOUT
2
8
AN110 F19
AN110 F18
12
VIN = 24V
VOUT = 1.5V
10
0
100
MAXIMUM LOAD CURRENT (A)
40
10
MAXIMUM LOAD CURRENT (A)
2
12
VIN = 24V
VOUT = 1.5V
MAXIMUM LOAD CURRENT (A)
10
0
12
VIN = 24V
VOUT = 1.5V
MAXIMUM LOAD CURRENT (A)
MAXIMUM LOAD CURRENT (A)
12
Figure 26. Metal Plate with
Gap Pad at 24VIN and 3.3VOUT
an110fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
AN110-7
Application Note 110
Table 1. 1.5V Output at 12A
VIN (V)
POWER LOSS CURVE
AIR FLOW (LFM)
HEATSINK
qJA (°C/W)
Figures 18
24
Figure 10
0
None
15.2
Figures 18
24
Figure 10
200
None
14
Figures 18
24
Figure 10
400
None
12
Figures 19
24
Figure 10
0
BGA Heatsink
13.9
Figures 19
24
Figure 10
200
BGA Heatsink
11.3
Figures 19
24
Figure 10
400
BGA Heatsink
10.25
Figures 20
24
Figure 10
0
Metal Plate
12
Figures 20
24
Figure 10
200
Metal Plate
9.5
Figures 20
24
Figure 10
400
Metal Plate
8.15
VIN (V)
POWER LOSS CURVE
AIR FLOW (LFM)
HEATSINK
qJA (°C/W)
Figures 24
24
Figure 11
0
None
14.3
Figures 24
24
Figure 11
200
None
13.1
Figures 24
24
Figure 11
400
None
11.1
Figures 25
24
Figure 11
0
BGA Heatsink
12.1
Figures 25
24
Figure 11
200
BGA Heatsink
9.6
Figures 25
24
Figure 11
400
BGA Heatsink
8.45
Figures 26
24
Figure 11
0
Metal Plate
10.7
Figures 26
24
Figure 11
200
Metal Plate
8.2
Figures 26
24
Figure 11
400
Metal Plate
6.85
DERATING CURVE
Table 2. 3.3V Output at 12A
DERATING CURVE
HEATSINK MANUFACTURER
Wakefield Engineering
Bergquist Company
PART NUMBER
PHONE NUMBER
LTN20069
603-635-2800
Gap Pad 1000SF
952-835-2322
an110fa
AN110-8
Linear Technology Corporation
LT 0910 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
” LINEAR TECHNOLOGY CORPORATION 2007