Specifications(PDF:361KB)

Small Cubic Type
5.0 Mega Pixel CCD
Monochrome PoCL Camera Link Camera
FV-L500B1
Product Specifications
RICOH COMPANY, LTD.
FV-L500B1
Product Specifications Rev. 1.02
1/12
Copyright & Disclaimer
Sensor Technology Co., Ltd. (DBA Sentech) believes the contents and specifications of its website, catalog,
documentation and ads are correct; however, Sentech provides no representation or warranty regarding such
information or product(s) contained therein. It is requested that Sentech be given appropriate acknowledgement in any
subsequent use of such work by a third party.
While every effort has been made to ensure that the details contained in Sentech’s website and all documentation are
correct and up-to-date, Sentech assumes no liability, legal or otherwise for any errors in listings, specifications, part
numbers, process, software or model applications. Sentech reserves the right to change specifications, product
descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using
such information assumes all risk for any and all damaged caused to themselves, a third party and/or property by
virtue of incorrect information and/or failure of these products. By installing and/or using a Sentech software
development kit or other similar product and/or information obtained from Sentech’s website, catalog, documentation
or ads, you hereby accept and understand these stated terms and conditions.
FV-L500B1
Product Specifications Rev. 1.02
2/12
Table of Contents
1.
Safety / Product Precautions ............................................................................................................................... 4
2.
Electronic / Mechanical / Environmental Specifications................................................................................... 6
2.1.
3.
Spectral Sensitivity Characteristics..................................................................................................................... 7
Connector Specifications..................................................................................................................................... 8
3.1.
3.2.
3.3.
Camera Link Connector...................................................................................................................................... 8
Power-I/O Connector .......................................................................................................................................... 9
Equivalent Circuit for the Input Pin of the I/O Connector.................................................................................. 10
4.
Dimensions.......................................................................................................................................................... 11
5.
Revision History.................................................................................................................................................. 12
FV-L500B1
Product Specifications Rev. 1.02
3/12
1. Safety / Product Precautions
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
For U.S.A.
!
CAUTION:
TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning:
This equipment generates and uses radio frequency energy and if
not installed and used properly, I.e., in strict accordance with the
instruction manual, may cause harmful interference to radio
communications. It has been tested and found to comply with the
limits for a Class A computing device pursuant to Subpart J of Part
15 of FCC Rules, which are designed to provide reasonable
protection against such interference when operated in a commercial
environment.
For Canada
The li ghtning flash with arrowhea d
symbol, within an equilateral triangle,
i s i nt ended t o alert the use r t o the
pre sence of uni nsulated “dangerous
v o l ta g e ” w i th in t h e p r o du c t ’ s
enclosure t hat may be of suffici ent
ma gnitude t o c onst i tute a ri sk of
electric shock to persons.
Warning:
The exclama ti on point wi t hi n a n
equilateral triangle is intended to alert
the user to the presence of import ant
operating and maintenance (servicing)
i n st r u c ti o ns in t h e l i te r a t u r e
accompanying the appliance.
WARNING:
This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Product Precautions
Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper
handling or storage could damage the camera.
Do not pull or damage the camera cable.
During camera use, do not wrap the unit in any material. This will cause the internal temperature of
the unit to increase.
Do not expose the camera to moisture, or do not try to operate it in wet areas.
Do not operate the camera beyond its temperature, humidity and power source ratings.
While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or
contamination from getting in the CCD or filter area and scratching or damaging this area.
Do not keep the camera under the following conditions:
In wet, moist, and high humidity areas
• Under hot direct sunlight
• In high temperature areas
• Near an object that releases a strong magnetic or electric field
• Areas with strong vibrations
Apply the power that satisfies the requirements specified in this document to the camera.
Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO
not scratch the surface of the glass.
FV-L500B1
Product Specifications Rev. 1.02
4/12
The camera is a general-purpose electronic device; using the camera for the equipment that may
threaten human life or cause dangers to human bodies directly in case of failure or malfunction of
the camera is not guaranteed. Use the camera for special purposes at your own risk.
FV-L500B1
Product Specifications Rev. 1.02
5/12
2. Electronic / Mechanical / Environmental Specifications
Model Number
Electronic
Specifications
FV-L500B1
Imager
2/3” Interline 5.0 Mega Pixel monochrome progressive: ICX625AL
Total Picture Elements
2456 (H) x 2058 (V)
Active Picture Elements
2448 (H) x 2058 (V)
Cell Size
3.45 (H) x 3.45 (V) µm
Scanning System
Progressive
Full Scanning, Partial Full Scanning,
½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning,
Scanning Method
Binning, Binning Partial Scanning,
Binning ½ Partial Scanning, Binning ¼ Partial Scanning,
Binning Variable Partial Scanning
Vertical Frequency
(Frame Rate)
Horizontal Frequency
Pixel Frequency
S/N
Ratio
33.264 kHz
64 MHz
@ 8bit output
<= 4 Digit (Gain 0 dB)
(Standard
@ 10bit output
<= 15 Digit (Gain 0 dB)
Deviation)
@ 12bit output
<= 60 Digit (Gain 0 dB)
Minimum Scene Illumination
Sync. System
Tap Configuration
Exposure Time
Digital 8, 10, or 12 bit Camera Link (Base Configuration)
2 Taps (2XE-1Y)
OFF, 1/8 to 1/209,000 sec. (Variable at every H and clock)
Gain
0 to 18.309 dB
Gamma
Power
0.24 Lux at F1.2
Internal
Video Output Format
1.0
Input Voltage
Consumption
Operational Mode
Communication
Mechanical
16 Hz
DC 12V± 10% via Camera Link connector
Less than 4.0 W
Free-run, Edge Preset Trigger (V-reset, Non-reset);
Pulse Width Trigger (V-reset, Non-reset)
RS232 via Camera Link connector
Dimensions
35 (W) x 35 (H) x 30.2 (D) mm (NOT including lens mount and the connector)
Specifications
35 (W) x 35 (H) x 40.7 (D) mm (NOT including the connector)
Optical Filter
No IR cut filter
Materials
Aluminum (AC)
Lens Mount
C mount
Interface Connector
I/O Connector: HR 10A-7R-6PB (Hirose) or equivalent
Camera Link Connector: SDR (3M) or equivalent
Weight
Environmental
Approximately 80g
Operational
Specifications
Temperature: -5 to 40⁰C
Temperature
Storage
Temperature: -30 to 65⁰C
FV-L500B1
Product Specifications Rev. 1.02
6/12
Vibration
20Hz to 200Hz to 20Hz (5min./cycle);
Acceleration 10G, 3 directions 30 min. each
Shock
Acceleration 38G, half amplitude 6ms, 3 directions 3 times each
Standard Compliancy
EMS: EN61000-6-2, EMI: EN55022 (Class B) , FCC PART15 subpart B classA
RoHS
2.1.
RoHS Compliant
Spectral Sensitivity Characteristics
1
Relative Response
0.8
0.6
0.4
0.2
0
400
500
FV-L500B1
Product Specifications Rev. 1.02
600
700
Wave length [nm]
800
900
1000
7/12
3. Connector Specifications
Power-I/O Connector
Camera Link Connector
3.1.
Camera Link Connector
SDR (3M) or equivalent
This product is a PoCL type.
When a frame grabber is PoCL compliant, DO NOT SUPPLY POWER FROM THE I/O CONNECTOR.
When a frame grabber is NOT PoCL compliant, supply power from the I/O connector.
Pin Assignment
Pin No.
Signal Name
Pin No.
Signal Name
1
+12V
14
GND
2
X0-
15
X0+
3
X1-
16
X1+
4
X2-
17
X2+
5
Xclk-
18
Xclk+
6
X3-
19
X3+
7
SerTC+
20
SerTC-
8
SerTFG-
21
SerTFG+
9
CC1-(TRG)
22
CC1+(TRG)
10
CC2+
23
CC2-
11
CC3-
24
CC3+
12
CC4+
25
CC4-
13
GND
26
+12V
FV-L500B1
Product Specifications Rev. 1.02
8/12
3.2.
Power-I/O Connector
HR10A-7R-6PB(Hirose)or equivalent
This connector is for the power supply (12Vdc) and input /output signals.
Use HR10A-7P-6S (Hirose) or equivalent for the cable side.
Pin Assignment
Pin No.
Signal Name
IN / OUT
1
GND
IN
Voltage
Low Voltage
High Voltage
0V
IN
0 to +0.99V
+2.3 to +3.3V
2
I/O-1
IN/OUT
OUT
0V
+3.3V
3
I/O-2
OUT
OUT
0V
+3.3V
4
I/O-3
OUT
OUT
0V
+3.3V
5
I/O-4
OUT
OUT
0V
+3.3V
6
+12Vdc
IN
+12Vdc
Input/output signals can be assigned through the camera setting communication (see table 4).
Trigger input signal can be assigned either on Camera Link connector (CC1) or on the No. 2 pin of the
Power-I/O connector through the camera setting communication.
IO Signal Patterns
Command No.
F0H[3..0]
Option 0
(Initial Setting)
0H
HR10A-7R-6PB (Hirose)
No.2 Pin
No.3 Pin
No.4 Pin
No.5 Pin
I/O-1 (SP4)
I/O-2 (SP3)
I/O-3 (SP2)
I/O-4 (SP1)
IN/TRG
N/A
N/A
OUT/TRG
Option 1
1H
Option 2
2H
OUT/CC4
OUT/CC3
OUT/CC”2
OUT/CC1
Option 3
3H
OUT/FVAL
OUT/XSG
OUT/XSUB
OUT/CC1
Option 4
4H
OUT/
OUT/
OUT/FVAL
OUT/LVAL
Right Image Data
Left Image Data
(MSB)
(MSB)
OUT/XHD
OUT/EXPDUR
(high-active)
(Exposure)
OUT/TRG
OUT/CC1
OUT/VD
N/A
N/A
OUT/HD
Option 5
5H
Option 6
6H
Others
7H-FH
For Test Use Only
For Test Use Only
Note 1: Output trigger signal has a latency of 30CLK (Approximately 470 nseconds) from input trigger signal.
Note 2: To input trigger signal from the I/O connector, change the setting of 12H.5.
Note 3: EXPDUR becomes high during exposure.
FV-L500B1
Product Specifications Rev. 1.02
9/12
3.3.
Equivalent Circuit for the Input Pin of the I/O Connector
+3.3V
+3.3V
On resister Max. = 30ohm
100ohm
10kohm
TRIGGER IN
TC7WH241FK
TOSHIBA
FV-L500B1
Product Specifications Rev. 1.02
10/12
4. Dimensions
Unit: mm
FV-L500B1
Product Specifications Rev. 1.02
11/12
5. Revision History
Rev
Date
1.00
1.01
2012/06/15
2012/07/13
1.02
2012/09/27
Changes
Note
Initial Release
Updated
Document Title
Dimensions
Electronic Specifications
Shutter Speed Exposure Time
Updated
Power supply through No.6 pin of the power-I/O connector became available.
RICOH COMPANY, LTD.
URL http://www.ricoh.com/fa_security/
FV-L500B1
Product Specifications Rev. 1.02
12/12