GigE Vision UXGA Monochrome CCD Camera FV-G200B1 Product Specifications RICOH COMPANY, LTD. FV-G200B1 Product Specifications Rev. 1.03 1/14 Copyright & Disclaimer Sensor Technology Co., Ltd. (DBA Sentech) believes the contents and specifications of its website, catalog, documentation and ads are correct; however, Sentech provides no representation or warranty regarding such information or product(s) contained therein. It is requested that Sentech be given appropriate acknowledgement in any subsequent use of such work by a third party. While every effort has been made to ensure that the details contained in Sentech’s website and all documentation are correct and up-to-date, Sentech assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers, process, software or model applications. Sentech reserves the right to change specifications, product descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these products. By installing and/or using a Sentech software development kit or other similar product and/or information obtained from Sentech’s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions. FV-G200B1 Product Specifications Rev. 1.03 2/14 Table of Contents 1 Safety / Product Precautions ...............................................................................................................................4 2 Electronic / Mechanical / Environmental Specifications...................................................................................6 2.1 3 Spectral Sensitivity Characteristics......................................................................................................................... 8 Connector Specifications .....................................................................................................................................9 3.1 RJ45 Connector ...................................................................................................................................................... 9 3.2 DC Iris Lens Connector ........................................................................................................................................ 10 3.3 Power-I/O connector ............................................................................................................................................. 10 3.3.1 Equivalent Circuit for the Input Pin of the I/O Connector .................................................................................. 12 4 Dimensions ..........................................................................................................................................................13 FV-G200B1 Product Specifications Rev. 1.03 3/14 1 Safety / Product Precautions Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U.S.A. ! Warning: CAUTION: TO REDUCE TH E RISK OF EL ECTRIC SHOCK, DO N OT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This equipment generates and uses radio frequency energy and if not installed and used properly, I.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. For Canada The li ghtning flash with arrowhea d symbol, within an equilateral triangle, i s i nt ended t o alert the use r t o the pre sence of uni nsulated “dangerous v o l ta g e ” w i th in t h e p r o du c t ’ s enclosure t hat may be of suffici ent ma gnitude t o c onst i tute a ri sk of electric shock to persons. Warning: The exclama ti on point wi t hi n a n equilateral triangle is intended to alert the user to the presence of import ant operating and maintenance (servicing) i n st r u c ti o ns in t h e l i te r a t u r e accompanying the appliance. WARNING: This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Product Precautions Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or storage could damage the camera. Do not pull or damage the camera cable. During camera use, do not wrap the unit in any material. This will cause the internal temperature of the unit to increase. Do not expose the camera to moisture, or do not try to operate it in wet areas. Do not operate the camera beyond its temperature, humidity and power source ratings. While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or contamination from getting in the CCD or filter area and scratching or damaging this area. Do not keep the camera under the following conditions: In wet, moist, and high humidity areas • Under hot direct sunlight • In high temperature areas • Near an object that releases a strong magnetic or electric field • Areas with strong vibrations Apply the power that satisfies the requirements specified in this document to the camera. Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not scratch the surface of the glass. FV-G200B1 Product Specifications Rev. 1.03 4/14 The camera is a general-purpose electronic device; using the camera for the equipment that may threaten human life or cause dangers to human bodies directly in case of failure or malfunction of the camera is not guaranteed. Use the camera for special purposes at your own risk. FV-G200B1 Product Specifications Rev. 1.03 5/14 2 Electronic / Mechanical / Environmental Specifications Product Electronic Specifications FV-G200B1 Imager 1/1.8” Interline UXGA monochrome progressive CCD: ICX274AL Total Picture Elements Active Picture Elements Cell Size 1688 (H) x 1246 (V) UXGA: 1624 (H) x 1236 (V) 4.4 (H) x 4.4 (V) µm Scanning System Vertical Frequency (Frame Rate) Progressive 15.31668 Hz at full resolution 0.29261 to 61.26674 Hz adjustable via the communication (Frame rate depends on the AOI setting) Maximum frame rate (61.26674 Hz) is when vertical resolution AOI setting is 232. Horizontal Frequency 19.1761 kHz Pixel Frequency 36.8181 MHz Noise Level @ 8bit output ≤ 3 Digit (Gain 0 dB) @ 10bit output ≤ 12 Digit (Gain 0 dB) @ 12bit output Minimum Scene Illumination Sync. System ≤ 48 Digit (Gain 0 dB) 0.16 Lux at F1.2, 15.31668 Hz Internal Video Output Format Digital 8, 10 or 12 bit Raw Data or RGB 8 bit Interface IEEE802.3 (1000BASE-T) Protocol GigE Vision® 1.2 and GenICam™ 2.0 compliant Preset continuous mode: 1 useconds to 16,777,215 useconds Exposure Time Preset trigger mode: 1 useconds to 16,777,215 useconds Pulse width mode: 1 useconds to Unlimited ALC Auto iris lens, electronic iris and AGC (ON/OFF) Gain 0 to 20.4 dB Gamma Gamma 1.0 (Factory default) or uploadable gamma table AOI Function Programmable AOI setting via the communication Smear Reduction Selectable ON/OFF via the communication Operational Mode Free-run, Edge preset trigger, Pulse width trigger (unlimited long exposure) Communication UART Communication through Ethernet port I/O One opt-isolated input and two open-collector outputs Auto IRIS Lens Control DC IRIS control input with video level target, peak/average and zone weight settings via the communication Power Mechanical Dimensions Specifications Optical Filter Input Voltage Consumption Optical Center Accuracy Material +10.8 to +26.4 Vdc Less than 5.00 W 35 (W) x 35 (H) x 50.8(D) mm excluding connectors No Filter Positional accuracy in H and V directions: +/- 0.3 mm Rotational accuracy of H and V: +/- 1.5 deg. Aluminum (AC) Lens Mount C mount Connectors RJ45 connector Power-I/O connector: HR10A-7R-6PB (Hirose) or equivalent DC IRIS lens connector: M1951 (EMUDEN) or equivalent Camera Mount Screws Two 1/4” Tripod screw holes: (One on each top and bottom plate), Twelve M4 screws holes: (Four on each top and bottom plate, two on each side plate) FV-G200B1 Product Specifications Rev. 1.03 6/14 Weight Approximately 120 g Product FV-G200B1 Environmental Specifications Environmental Temperature -5⁰C Minimum Operational Camera housing temperature (top plate) shall not exceed 65⁰C Temperature Maximum (This corresponds to an environmental temperature of approximately 35⁰C) Environmental Temperature: -30⁰C to 65⁰C Storage temperature Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each Shock Standard Compliancy RoHS Acceleration 38G, half amplitude 6ms, 3 directions 3 times each EMS: EN61000-6-2, EMI: EN55011, FCC PART15 subpart B classA RoHS Compliant Note: Please use this camera in surrounding temperature conditions that are less than 35⁰C or in conditions where the camera’s top case plate is less than 65⁰C. When the camera is used in surrounding temperatures that exceed 35⁰C, please make sure that the camera is set up to properly radiate heat (maintaining the camera’s top case plate’s temperature to be less than 65⁰C). Taking these steps will maintain the heat rating of the electronic components of the camera. FV-G200B1 Product Specifications Rev. 1.03 7/14 2.1 Spectral Sensitivity Characteristics 1 Relative Response 0.8 0.6 0.4 0.2 0 400 500 FV-G200B1 Product Specifications Rev. 1.03 600 700 Wave length [nm] 800 900 1000 8/14 3 Connector Specifications DC Iris Lens Connector RJ45 Connector Power-I/O Connector 3.1 RJ45 Connector This product is NOT a PoE type. Apply power (+10.8 to +26.4Vdc) ONLY through the I/O connector. Pin Assignment: LED Information: Pin No. Signal Name 1 2 3 4 5 6 7 8 TA+ TATB+ TC+ TCTBTD+ TD- The camera is powered-on Green LED Yellow LED Status Green Light ON Orange Light ON Power ON Green Light ON Orange Light Blinking 1Gb Transferring Light OFF Orange Light Blinking 100 Mb Transferring Green light: ON Yellow light: Blinking 1 Gb Transferring Green light: OFF Yellow light: Blinking 100 Mb Transferring Please use a 1Gb supported NIC, HUB and LAN cable. Check that the NIC and HUB being used is “1Gb transferring”. Damaging or mishandling the CAT5e cable may cause the transferring speed to change from 1Gb to 100Mb. If this happens, please replace the CAT5e cable. FV-G200B1 Product Specifications Rev. 1.03 9/14 3.2 DC Iris Lens Connector M1951 (EMUDEN) or equivalent. Pin Assignment Pin No. 1 2 3 4 3.3 3 4 Signal Name DAMPDAMP+ DRIVE+ DRIVE- 1 2 Power-I/O connector HR10A-7R-6PB（Hirose）or equivalent This connector is for the power supply (12Vdc) and input /output signals. Use HR10A-7P-6S (Hirose) or equivalent for the cable side. Pin Assignment Pin No. 1 2 3 Signal Name GND I/O-1 I/O-2 IN / OUT IN OUT OUT 4 TRG_In- IN 5 TRG_In+ IN 6 POWER IN IN Voltage 0V +3.3V LVTTL +3.3V LVTTL Low: Smaller than +1.0V (Opt. Isolated -) High: +3.0 to +26.4V (Opt. Isolated +) *potential difference between TRG_In- and TRG_In+ +10.8 to +26.4 Vdc Output signals can be assigned through the camera setting communication. (Device Code = 00H, Command = F0H and F1H) IO Signal Patterns for Pin No.2 (I/O-1) and Pin No.3 (I/O-2) Command No. F0H[3..0] F1[3] F0H[7..4] F1[4] For I/O-1 (Pin No. 2) For I/O-2 (Pin No.3) 0H 0H (initial setting) 1H Set Value 1H Set Value 2H 2H (initial setting) 3H 3H 4H 4H 5H 5H 6H 6H 7H-FH 7H-FH - FV-G200B1 Product Specifications Rev. 1.03 HR10A-7R-6PB (Hirose) I/O-1 (Pin No.2) / I/O-2 (Pin No.3) FrameTriggerWait (initial setting for I/O-1) UserOutput ExposureActive (initial setting for I/O-2) TriggerAuxiliary TriggerInternal SensorReadOut StrobeSignal For Test Use Only 10/14 Note: I/O-1 can be assigned only by F0H[3..0] and F1[3], and I/O-2 can be assigned only by F0H[7..4] and F1[4]. 1) FrameTriggerWait The user can check the camera condition (camera exposure and image output processing by the trigger signal with this FrameTriggerWait signal). This signal is LOW for the period from the trigger input signal to the image output. a) High status (3.3V): No processing by the trigger signal. The camera accepts the trigger signal. b) Low status (0V): The camera is exposed and the image output processes by the trigger signal. The camera default setting is the input trigger signal is INVALID while at the low status of this signal. When the exposure starts while the image output by the next trigger signal, please change the camera setting (Device code: 00H, Command No. :13H) to accept the trigger signal while the image outputs. The noise appears on the image when the exposure begins while the image is output. The noise appears on the image when the start exposure while the image is output. In this case, please change the “H reset” for the exposure start mode (Device code: 00H, Command No. : 12H) to change the exposure start point to the next HD timing. 2) UserOutput The status of the UserOutput signal can change with the “UserOutputValue”. a) High status (3.3V) b) Low status (0V). 3) ExposureActive The user can check the exposure time with the ExposureActive signal. a) High status (3.3V): The camera is exposing b) Low status (0V): The camera is not exposed 4) TriggerAuxiliary The TriggerAuxiliary signal is the input trigger signal. 5) TriggerInternal The TriggerInternal signal is the input trigger signal with the trigger delay time. 6) SensorReadOut The SensorReadOut signal is the FVAL signal, which is the image output period of the time. 7) StrobeSignal The StrobeSignal signal is the strobe control signal. FV-G200B1 Product Specifications Rev. 1.03 11/14 3.3.1 Equivalent Circuit for the Input Pin of the I/O Connector HR10A-7R-6PB (HIROSE) or equivalent connector 6 5 4 +3.3V 3 2 2.2K 1 6 1 4 3 +10.8 to +26.4V Trigger_In+ Trigger_InIO_Out IO_Out GND +3 to +26.4V 3 to 5mA Trigger Signal Customer GND TOSHIBA TLP181 +3.3V 3 1K 2 RN1105MFV 1 TOSHIBA +3.3V 3 1K 2 RN1105MFV 1 TOSHIBA FV-G200B1 Product Specifications Rev. 1.03 12/14 4 Dimensions Unit: mm FV-G200B1 Product Specifications Rev. 1.03 13/14 Revision History Rev Date Changes 1.00 1.01 2012/06/17 2012/06/18 1.02 2012/07/03 1.03 2012/08/25 Note Initial Release Updated The output Signal “StrobeOut” is corrected to “StrobeSignal” Updated Document title Electronic Specifications Shutter Speed Exposure Time The maximum value for the Exposure Time is corrected to 16,777,215 Equivalent Circuit for the Input Pin of the I/O Connector Updated Pin Assignment of Power-I/O Connector RICOH COMPANY, LTD. URL http://www.ricoh.com/fa_security/ FV-G200B1 Product Specifications Rev. 1.03 14/14