DS8209LM 07

®
RT8209L/M
Single Synchronous Buck Controller
General Description
Features
The RT8209L/M PWM controller provides high efficiency,
excellent transient response, and high DC output accuracy
needed for stepping down high voltage batteries to
generate low voltage CPU core, I/O, and chipset RAM
supplies in notebook computers.
z
Ultra High Efficiency
z
Resistor Programmable Current Limit by Low Side
RDS(ON) Sense (Lossless Limit)
4700ppm/°°C Current Sensing
Quick Load Step Response within 100ns
1% VFB Accuracy over Line and Load
4.5V to 26V Battery Input Range
Resistor Programmable Frequency
Integrated Bootstrap Switch
Integrated Negative Current Limiter
Over/Under Voltage Protection
Internal Soft-Start and Soft-Discharge Output
Power Good Indicator
RoHS Compliant and Halogen Free
z
z
z
z
z
z
z
z
z
Applications
z
z
z
Notebook Computers
System Power Supplies
I/O Supplies
Pin Configurations
(TOP VIEW)
1
12
2
11
Richtek products are :
`
RoHS compliant and compatible with the current requireSuitable for use in SnPb or Pb-free soldering processes.
6
7
9
UGATE
PHASE
CS
VDDP
8
RT8209L
WQFN-16L 3x3
Note :
ments of IPC/JEDEC J-STD-020.
10
17
4
5
L : WQFN-16L 3x3
M : WQFN-14L 3.5x3.5
`
NC
3
TON
VOUT
VDD
FB
PGOOD
2
BOOT
Lead Plating System
G : Green (Halogen Free and Pb Free)
Z : ECO (Ecological Element with
Halogen Free and Pb free)
16 15 14 13
VOUT
VDD
FB
PGOOD
NC
GND
PGND
LGATE
Package Type
QW : WQFN-16L 3x3 (W-Type)
QW : WQFN-14L 3.5x3.5 (W-Type)
TON
EN/DEM
NC
BOOT
RT8209
1
14
3
UGATE
PHASE
11 CS
10 VDDP
9 LGATE
13
12
NC
4
15
5
6
7
8
PGND
Ordering Information
z
EN/DEM
The RT8209L/M achieves high efficiency at a reduced cost
by eliminating the current sense resistor found in
traditional current mode PWMs. Efficiency is further
enhanced by its ability to drive very large synchronous
rectifier MOSFETs. The buck conversion allows this device
to directly step down high voltage batteries for low voltage
supplies as low as 0.75V. The RT8209L is in a WQFN16L 3x3 package, the RT8209M is in a WQFN-14L 3.5x3.5
package.
GND
The constant-on-time PWM control scheme handles wide
input/output voltage ratios with ease and provides 100ns
“instant-on” response to load transients while maintaining
a relatively constant switching frequency.
z
RT8209M
WQFN-14L 3.5x3.5
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
1
RT8209L/M
Marking Information
RT8209LGQW
RT8209MGQW
JX= : Product Code
JX=YM
DNN
A8= : Product Code
YMDNN : Date Code
A8=YM
DNN
RT8209LZQW
RT8209MZQW
JX : Product Code
JX YM
DNN
YMDNN : Date Code
A5 : Product Code
YMDNN : Date Code
A5 YM
DNN
YMDNN : Date Code
Typical Application Circuit
RTON
250k
VIN
4.5V to 26V
RT8209L/M
BOOT
TON
VDDP
VDDP
R2
100k
R1
10
C2
1µF
UGATE
LGATE
PGND
CS
C3
0.1µF
Q1
BSC119 L1
1µH
N03S
BSC119N03S
Q2
VOUT = 1.05V
* : Optional
R7*
C7*
R8
12k
C5* C6*
C1
220µF
FB
R6
18k
R9
30k
VOUT
EN/DEM
CCM/DEM
R5
0
C4
10µF
PHASE
VDD
PGOOD
PGOOD
R4
0
GND
Functional Pin Description
Pin No.
Pin Name
Pin Function
RT8209L
RT8209M
1
3
VOUT
Output Voltage Pin. Connect to the output of PWM converter.
VOUT is an input of the PWM controller.
2
4
VDD
Supply Input Pin. Analog supply for entire IC. Bypass to GND
with a 1μF ceramic capacitor.
3
5
FB
Feedback Input Pin. Connect FB to a resistive voltage divider
from VOUT to GND to adjust VOUT from 0.75V to 3.3V.
4
6
PGOOD
Power Good Indicator it is an Open Drain Output of PWM
Converter. This pin will be pulled high when the output voltage
is within the target range.
5, 14,
15 (Exposed pad) NC
17 (Exposed pad)
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
2
No Internal Connection. The exposed pad must be soldered to
a large PCB for maximum power dissipation.
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
Pin No.
Pin Name
Pin Function
6
7
GND
Analog Ground.
7
8
PGND
Power Ground.
8
9
LGATE
9
10
VDDP
10
11
CS
11
12
PHASE
12
13
UGATE
13
14
BOOT
15
1
EN/DEM
16
2
TON
Low Side N-MOSFET Gate Driver Output for PWM. This pin swings between
GND and VDDP.
Gate Driver Supply for External MOSFETs. Bypass to GND with a 1μF ceramic
capacitor.
Over Current Trip Point Set Input. Connect resistor from this pin to signal ground
to set threshold for both over current and negative over current limit.
UGATE High Side Gate Driver Return. Also serves as anode of over current
comparator.
High Side N-MOSFET Floating Gate Driver Output for PWM Converter. This pin
swings between PHASE and BOOT.
Bootstrap Capacitor Connection for PWM Converter. Connect to an external
ceramic capacitor to PHASE.
Enable/Diode Emulation Mode Control Input. Connect to VDD for diode
emulation mode, connect to GND for shutdown and float the pin for CCM mode.
On Time/Frequency Adjustment Pin. Connect to PHASE through a resistor.
TON is an input for the PWM controller.
Function Block Diagram
TRIG
On-time
Compute
1-SHOT
VOUT
TON
SS
(internal)
BOOT
R
- +
GM
+
-
-
S
+
+
125% VREF
-
70% VREF
+
OV
UV
Latch
S1
Q
VDDP
1-SHOT
LGATE
DRV
PGND
PGOOD
-
90% VREF
SS Ramp
+
Thermal
Shutdown
EN/DEM
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
PHASE
Latch
S1
Q
-
VDD
UGATE
DRV
Min. TOFF
Q
TRIG
VREF
FB
Q
Diode
Emulation
10µA
+
+
GM
-
CS
GND
-
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
3
RT8209L/M
Absolute Maximum Ratings
(Note 1)
VDD, VDDP, VOUT, EN/DEM, FB, PGOOD, TON to GND ------------------------------------------------------BOOT to PHASE ---------------------------------------------------------------------------------------------------------z PHASE to GND
DC ----------------------------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------------------------z UGATE to PHASE
DC ----------------------------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------------------------z CS to GND -----------------------------------------------------------------------------------------------------------------z LGATE to GND ------------------------------------------------------------------------------------------------------------z LGATE to GND
DC ----------------------------------------------------------------------------------------------------------------------------< 20ns ----------------------------------------------------------------------------------------------------------------------z PGND to GND -------------------------------------------------------------------------------------------------------------z Power Dissipation, PD @ TA = 25°C
z
z
z
z
z
z
z
WQFN−16L 3x3 -----------------------------------------------------------------------------------------------------------WQFN−14L 3.5x3.5 ------------------------------------------------------------------------------------------------------Package Thermal Resistance (Note 2)
WQFN−16L 3x3, θJA -----------------------------------------------------------------------------------------------------WQFN−16L 3x3, θJC -----------------------------------------------------------------------------------------------------WQFN−14L 3.5x3.5, θJA ------------------------------------------------------------------------------------------------WQFN−14L 3.5x3.5, θJC ------------------------------------------------------------------------------------------------Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------------Junction Temperature ----------------------------------------------------------------------------------------------------Storage Temperature Range -------------------------------------------------------------------------------------------ESD Susceptibility (Note 3)
HBM (Human Body Mode) ---------------------------------------------------------------------------------------------MM (Machine Mode) ------------------------------------------------------------------------------------------------------
Recommended Operating Conditions
z
z
z
z
www.richtek.com
4
−0.3V to 32V
−8V to 38V
−0.3V to 6V
−5V to 7.5V
−0.3V to 6V
−0.3V to 6V
−0.3V to 6V
−2.5V to 7.5V
−0.3V to 0.3V
1.471W
1.667W
68°C/W
7.5°C/W
60°C/W
7.5°C/W
260°C
150°C
−65°C to 150°C
2kV
200V
(Note 4)
Input Voltage, VIN ---------------------------------------------------------------------------------------------------------Supply Voltage, VDD, VDDP ---------------------------------------------------------------------------------------------Junction Temperature Range -------------------------------------------------------------------------------------------Ambient Temperature Range --------------------------------------------------------------------------------------------
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
−0.3V to 6V
−0.3V to 6V
4.5V to 26V
4.5V to 5.5V
−40°C to 125°C
−40°C to 85°C
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
Electrical Characteristics
(VIN = 15V, VDD = VDDP = 5V, TA = 25°C, unless otherwise specified)
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
μA
PWM Controller
IVDD
IVDDP
VFB = 0.8V, VEN/DEM = 5V
VFB = 0.8V, VEN/DEM = 5V
---
500
1
800
10
ISHDN_VDD
VEN/DEM = 0V
--
1
10
FB Reference Voltage
FB Input Bias Current
ISHDN_VDDP VEN/DEM = 0V
VREF
VDD = 4.5V to 5.5V
VFB = 0.75V
-0.742
−1
-0.750
0.1
1
0.758
1
Output Voltage Range
VOUT
0.75
--
3.3
V
336
420
504
ns
250
400
550
ns
EN/DEM = GND
--
20
--
Ω
CS to GND
9
10
11
μA
On the basis of 25°C
--
4700
--
ppm/°C
PHASE to GND
--
1x
VOC_TH
--
mV
PHASE to GND, EN/DEM = 5V
−10
−10
---
10
5
mV
mV
Current Limit Threshold
GND − PHASE, VCS = 200mV
190
200
210
mV
Current Limit Setting Range
Output UV Threshold
Output UV Hysteresis
CS to GND
UVP detect Falling edge
50
60
--
-70
3
200
80
--
mV
%
%
OVP detect Rising edge
FB forced above OV threshold
Falling edge, PWM disabled below
this level
120
--
125
20
130
--
%
μs
3.7
3.9
4.1
V
--
200
--
mV
--
2
--
ms
2.5
155
---
ms
°C
Quiescent Supply Current
Shutdown Current
On Time
tON
Minimum Off-Time
VOUT Shutdown Discharge
Resistance
Current Sensing
tOFF_MIN
Current Limiter Source Current
Current Limiter Temperature
TCICS
Coefficient
Negative Current Limiter
VNOC_TH
Threshold
Current Comparator Offset
Zero Crossing Threshold
VPHASE = 12V, VOUT = 2.5V,
R TON = 250kΩ
μA
V
μA
Fault Protection
OVP Threshold
OV Fault Delay
VDD Under Voltage Lockout
Threshold
UVLO Hysteresis
VFB_OVP
ΔVUVLO
ΔVUVLO
Current Limit Step Duration at
Soft-Start
UVP Blanking Time
Thermal Shutdown
TSHDN
---
Thermal Shutdown Hysteresis
ΔTSHDN
--
10
--
°C
--
2.5
5
Ω
--
1.5
3
Ω
tSS
Each step From EN high to internal
VREF reach 0.71V (0 to 95%)
From EN signal going high
Driver On-Resistance
UGATE Driver Source
RUGATEsr
UGATE Driver Sink
RUGATEsk
VBOOT − VPHASE = 5V,
UGATE, High State
VBOOT − VPHASE = 5V,
UGATE, Low State
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
5
RT8209L/M
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
LGATE Driver Source
RLGATEsr
LGATE, High State
--
2.5
5
Ω
LGATE Driver Sink
RLGATEsk
LGATE, Low State
--
1
2
Ω
--
1
--
A
--
1
--
A
A
UGATE Driver Source/Sink
Current
LGATE Driver Source Current
VUGATE − VPHASE = 2.5V,
VBOOT − VPHASE = 5V
VLGATE = 2.5V
LGATE Driver Sink Current
VLGATE = 2.5V
--
3
--
LGATE Rising (V PHASE = 1.5V)
--
30
--
UGATE Rising
--
30
--
VDDP to BOOT, 10mA
--
--
90
--
--
0.8
2.9
--
--
--
2
--
EN/DEM = VDD
--
1
5
EN/DEM = 0
−5
1
--
87
90
93
--
125
--
--
3
--
%
--
2.5
--
μs
--
--
0.4
V
--
--
1
μA
Dead Time
Internal BOOT Charging Switch
On Resistance
Logic I/O
Logic-Low
EN/DEM Logic
Logic-High
Input Voltage
float
Logic Input Current
ns
Ω
V
μA
PGOOD
PGOOD Threshold
VFB with respect to reference,
PGOOD from Low to High
VFB with respect to reference,
PGOOD from High to Low
PGOOD Hysteresis
Output Low Voltage
Falling Edge, FB forced below
PGOOD trip threshold
ISINK = 1mA
Leakage Current
High State, Forced to 5V
Fault Propagation Delay
%
Note 1. Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the device. These are for
stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the
operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended
periods may remain possibility to affect device reliability.
Note 2. θJA is measured in the natural convection at TA = 25°C on a high effective four-layer thermal conductivity test board of
JEDEC 51-7 thermal measurement standard. The case point of θJC is on the exposed pad of the package.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
6
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
Typical Operating Characteristics
2.5V Efficiency vs. Load Current
1.05V Efficiency vs. Load Current
100
DEM Mode
90
80
80
70
70
Efficiency (%)
Efficiency (%)
90
100
60
50
40
30
20
CCM Mode
10
0
0.001
60
50
40
30
20
VIN = 8V, VOUT = 2.5V,
EN = VDD & Floating.
0.01
0.1
1
DEM Mode
CCM Mode
VIN = 8V, VOUT = 1.05V,
EN = VDD & Floating.
10
0
0.001
10
0.01
Load Current (A)
90
80
70
70
Efficiency (%)
Efficiency (%)
DEM Mode
60
50
40
30
VIN = 12V, VOUT = 2.5V,
EN = VDD & Floating.
0
0.001
0.01
0.1
1
DEM Mode
60
50
40
30
20
CCM Mode
10
CCM Mode
10
0
0.001
10
0.01
Load Current (A)
80
80
70
70
Efficiency (%)
90
60
50
40
30
0
0.001
1
10
100
90 DEM Mode
10
0.1
1.05V Efficiency vs. Load Current
2.5V Efficiency vs. Load Current
20
VIN = 12V, VOUT = 1.05V,
EN = VDD & Floating.
Load Current (A)
100
Efficiency (%)
10
100
80
20
1
1.05V Efficiency vs. Load Current
2.5V Efficiency vs. Load Current
100
90
0.1
Load Current (A)
60
50
40
30
20
CCM Mode
VIN = 20V, VOUT = 2.5V,
EN = VDD & Floating.
0.01
0.1
1
Load Current (A)
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
10
10
DEM Mode
CCM Mode
0
0.001
0.01
VIN = 20V, VOUT = 1.05V,
EN = VDD & Floating.
0.1
1
10
Load Current (A)
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
7
RT8209L/M
Switching Frequency vs. Input Voltage
Switching Frequency vs. RTON Resistance
500
CCM Mode
VIN = 15V, EN = Floating
800
Switching Frequency (kHz)1
Switching Frequency (kHz)1
900
700
600
VOUT = 2.5V
500
400
300
VOUT = 1.05V
200
100
450
400
350
300
VOUT = 1.05V
250
200
150
100
50
0
0
100
200
300
400
500
600
6
700
10
400
VIN = 12V, VOUT = 1.05V,
EN = VDD & Floating.
300
Switching Frequency (kHz)1
Switching Frequency (kHz)1
350
CCM Mode
250
200
150
DEM Mode
100
50
0
0.001
0.01
0.1
1
350
26
300
CCM Mode
250
200
150
DEM Mode
100
50
0
0.001
10
0.01
0.1
1
10
Load Current (A)
2.5V Switching Frequency vs. Load Current
2.5V Switching Frequency vs. Load Current
450
400
CCM Mode
350
300
DEM Mode
250
200
150
100
VIN = 12V
VOUT = 2.5V
EN = VDD & Floating
50
0.01
0.1
1
Load Current (A)
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
10
Switching Frequency (kHz) 1
450
www.richtek.com
8
22
VIN = 20V, VOUT = 1.05V,
EN = VDD & Floating.
Load Current (A)
0
0.001
18
1.05V Switching Frequency vs. Load Current
1.05V Switching Frequency vs. Load Current
400
14
Input Voltage (V)
RTON Resistance (k Ω)
Switching Frequency (kHz)1
CCM Mode
IOUT = 2A, EN = Floating
VOUT = 2.5V
400
CCM Mode
350
300
250
DEM Mode
200
150
100
VIN = 20V
VOUT = 2.5V
EN = VDD & Floating
50
0
0.001
0.01
0.1
1
10
Load Current (A)
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
Shutdown Input Current vs. Input Voltage
Power On from EN (CCM Mode)
Shutdown Input Current (μA)1
1
0.8
VOUT
(500mV/Div)
UGATE
(20V/Div)
0.6
0.4
0.2
EN = GND, No Load
0
7
9
11
13
15
17
19
21
23
EN
(5V/Div)
PGOOD
(5V/Div)
25
No Load, VIN = 12V, VOUT = 1.05V, EN = Floating
Time (400μs/Div)
Input Voltage (V)
Power On from EN (DEM Mode)
OVP (DEM Mode)
VIN = 12V, VOUT = 2.5V
EN = VDD, No Load
VOUT
(500mV/Div)
UGATE
(20V/Div)
EN
(5V/Div)
PGOOD
(5V/Div)
VOUT
(1V/Div)
UGATE
(20V/Div)
No Load, VIN = 12V, VOUT = 1.05V, EN = VDD
LGATE
(5V/Div)
Time (400μs/Div)
Time (100μs/Div)
2.5V Load Transient Response
UVP (DEM Mode)
VIN = 12V, VOUT = 1.05V
EN = VDD, No Load
VOUT_accoupled
(100mV/Div)
IL
(10A/Div)
VOUT
(500mV/Div)
IL
(10A/Div)
UGATE
(20V/Div)
UGATE
(20V/Div)
LGATE
(5V/Div)
LGATE
(5V/Div)
Time (20μs/Div)
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
VIN = 12V, VOUT = 2.5V, EN = VDD (CCM Mode)
Time (20μs/Div)
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
9
RT8209L/M
Mode Transition DEM to CCM
Mode Transition CCM to DEM
VOUT_ac-
VOUT_ac-
coupled
coupled
(100mV/Div)
(100mV/Div)
UGATE
(20V/Div)
UGATE
(20V/Div)
LGATE
(5V/Div)
LGATE
(5V/Div)
EN
(5V/Div)
EN
(5V/Div)
VIN = 12V, No Load
Time (40μs/Div)
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
10
VIN = 12V, No Load
Time (40μs/Div)
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
Application Information
The RT8209L/M PWM controller provides high efficiency,
excellent transient response, and high DC output accuracy
needed for stepping down high voltage batteries to
generate low voltage CPU core, I/O, and chipset RAM
supplies in notebook computers. Richtek Mach
ResponseTM technology is specifically designed for
providing 100ns “instant-on” response to load steps while
maintaining a relatively constant operating frequency and
inductor operating point over a wide range of input voltages.
The topology circumvents the poor load transient timing
problems of fixed frequency current mode PWMs while
avoiding the problems caused by widely varying switching
frequencies in conventional constant on-time and constant
off-time PWM schemes. The DRV TM mode PWM
modulator is specifically designed to have better noise
immunity for such a single output application.
tON = 9.6p x RTON x (VOUT + 0.1) / (VIN − 0.3) + 50ns
PWM Operation
Diode Emulation Mode (EN/DEM = High)
TM
TM
The Mach Response DRV mode controller relies on
the output filter capacitor's effective series resistance
(ESR) to act as a current sense resistor, so the output
ripple voltage provides the PWM ramp signal. Refer to the
function block diagram, the synchronous UGATE driver
will be turned on at the beginning of each cycle. After the
internal one shot timer expires, the UGATE driver will be
turned off. The pulse width of this one shot is determined
by the converter's input voltage and the output voltage to
keep the frequency fairly constant over the input voltage
range. Another one shot sets a minimum off-time (400ns
typ.).
On-Time Control
The on-time one shot comparator has two inputs. One
input monitors the output voltage, while the other input
samples the input voltage and converts it to a current.
This input voltage proportional current is used to charge
an internal on-time capacitor. The on-time is the time
required for the voltage on this capacitor to charge from
zero volts to VOUT, thereby making the on-time of the high
side switch directly proportional to output voltage and
inversely proportional to input voltage. The implementation
results in a nearly constant switching frequency without
the need a clock generator.
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
Although this equation provides a good approximation to
start with, the accuracy depends on each design and
selection of the high side MOSFET.
And then the switching frequency is :
f=
VOUT
VIN × tON
RTON is the external resistor connected from the PHASE
to TON pin.
Mode Selection (EN/DEM) Operation
The EN/DEM pin enables the supply. When EN/DEM is
tied to VDD, the controller is enabled and operates in diode
emulation mode. When the EN/DEM pin is floating, the
RT8209L/M will operate in forced-CCM mode.
In diode emulation mode, the RT8209L/M automatically
reduces switching frequency at light load conditions to
maintain high efficiency. This reduction of frequency is
achieved smoothly and without increasing VOUT ripple or
load regulation. As the output current decreases from heavy
load condition, the inductor current is also reduced, and
eventually comes to the point that its valley touches zero
current, which is the boundary between continuous
conduction and discontinuous conduction modes. By
emulating the behavior of diodes, the low side MOSFET
allows only partial of negative current when the inductor
freewheeling current reach negative. As the load current
is further decreased, it takes longer and longer to discharge
the output capacitor to the level than requires the next
“ON” cycle. The on-time is kept the same as that in the
heavy load condition. In reverse, when the output current
increases from light load to heavy load, the switching
frequency increases to the preset value as the inductor
current reaches the continuous condition. The transition
load point to the light load operation can be calculated as
follows (Figure 1) :
ILOAD ≈
( VIN − VOUT )
2L
× tON
where tON is On-time.
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
11
RT8209L/M
IL
Slope = (VIN -VOUT) / L
iL, peak
the trip voltage setting resistor, RCS. The CS terminal
source 10μA ICS current, and the trip level is set to the CS
trip voltage, VCS can be calculated as following equation.
VCS (mV) = RCS (kΩ) x 10 (μA)
iLoad = iL, peak / 2
0
tON
t
Figure 1. Boundary Condition of CCM/DEM
The switching waveforms may appear noisy and
asynchronous when light loading causes diode emulation
operation, but this is a normal operating condition that
results in high light load efficiency. Trade offs in DEM
noise vs. light load efficiency is made by varying the
inductor value. Generally, low inductor values produce a
broader efficiency vs. load curve, while higher values result
in higher full load efficiency (assuming that the coil
resistance remains fixed) and less output voltage ripple.
The disadvantages for using higher inductor values include
larger physical size and degrade load transient response
(especially at low input voltage levels).
Forced-CCM Mode (EN/DEM = Floating)
The low noise, forced-CCM mode (EN/DEM = floating)
disables the zero-crossing comparator, which controls the
low side switch on-time. This causes the low-side gate
drive waveform to become the complement of the high
side gate drive waveform. This in turn causes the inductor
current to reverse at light loads as the PWM loop to
maintain a duty ratio VOUT/VIN. The benefit of forcedCCM mode is to keep the switching frequency fairly
constant, but it comes at a cost. The no load battery
current can be up to 10mA to 40mA, depending on the
external MOSFETs.
Current Limit Setting (OCP)
RT8209L/M has cycle-by-cycle current limiting control.
The current limit circuit employs a unique “valley” current
sensing algorithm. If PHASE voltage plus the current-limit
threshold is below zero, the PWM is not allowed to initiate
a new cycle (Figure 2). In order to provide both good
accuracy and a cost effective solution, the RT8209L/M
supports temperature compensated MOSFET RDS(ON)
sensing. The CS pin should be connected to GND through
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
12
Inductor current is monitored by the voltage between the
PGND pin and the PHASE pin, so the PHASE pin should
be connected to the drain terminal of the low-side
MOSFET. ICS has positive temperature coefficient to
compensate the temperature dependency of the RDS(ON).
PGND is used as the positive current sensing node so
PGND should be connected to the source terminal of the
bottom MOSFET.
As the comparison is done during the OFF state, VCS
sets the valley level of the inductor current. Thus, the
load current at over current threshold, ILOAD_OC, can be
calculated as follows.
VCS
IRipple
ILOAD_OC =
+
RDS(ON)
2
=
VCS
RDS(ON)
+
( V − VOUT ) × VOUT
1
× IN
2xLxf
VIN
IL
IL, peak
ILoad
ILIM
t
0
Figure 2. Valley Current-Limit
MOSFET Gate Driver (UGATE, LGATE)
The high side driver is designed to drive high current, low
RDS(ON) N-MOSFET (s). When configured as a floating
driver, 5V bias voltage is delivered from VDDP supply. The
average drive current is proportional to the gate charge at
VGS = 5V times switching frequency. The instantaneous
drive current is supplied by the flying capacitor between
BOOT and PHASE pins. A dead time to prevent shoot
through is internally generated between high side
MOSFET off to low side MOSFET on, and low side
MOSFET off to high side MOSFET on. The low side driver
is designed to drive high current, low RDS(ON) N-MOSFET (s).
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
The internal pull down transistor that drives LGATE low is
robust, with a 1Ω typical on resistance. A 5V bias voltage
is delivered from VDDP supply. The instantaneous drive
current is supplied by the flying capacitor between VDDP
and PGND.
For high current applications, some combinations of high
and low side MOSFETs might be encountered that will
cause excessive gate drain coupling, which can lead to
efficiency killing, EMI-producing shoot through currents.
This is often remedied by adding a resistor in series with
BOOT, which increases the turn-on time of the high side
MOSFET without degrading the turn-off time (Figure 3).
VIN
BOOT
10
UGATE
PHASE
Figure 3. Reducing the UGATE Rise Time
Power Good Output (PGOOD)
The power good output is an open drain output and requires
a pull-up resistor. When the output voltage is 25% above
or 10% below its set voltage, PGOOD gets pulled low. It
is held low until the output voltage returns to within these
tolerances once more. In soft start, PGOOD is actively
held low and is allowed to transition high until soft start is
over and the output reaches 93% of its set voltage. There
is a 2.5μs delay built into PGOOD circuitry to prevent
false transitions.
POR, UVLO and Soft-Start
Power On Reset (POR) occurs when VDD rises above to
approximately 4.1V, the RT8209L/M will reset the fault
latch and preparing the PWM for operation. Below 3.7
V(MIN), the VDD Under Voltage Lockout (UVLO) circuitry
inhibits switching by keeping UGATE and LGATE low. A
built-in soft-start is used to prevent surge current from
power supply input after EN/DEM is enabled. It clamps
the ramping of internal reference voltage which is compared
with FB signal. The typical soft-start duration is 2ms.
Furthermore the maximum allowed current limit is segment
in 2 steps during 2ms period.
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
Output Over Voltage Protection (OVP)
The output voltage can be continuously monitored for over
voltage protection. When the output voltage exceeds 25%
of the set voltage threshold, over voltage protection is
triggered and the low side MOSFET is latched on. This
activates the low side MOSFET to discharge the output
capacitor. The RT8209L/M is latched once OVP is
triggered and can only be released by VDD or EN/DEM
power-on reset. There is a 20μs delay built into the over
voltage protection circuit to prevent false transitions.
Output Under Voltage Protection (UVP)
The output voltage can be continuously monitored for under
voltage protection. When the output voltage is less than
70% of the set voltage threshold, under voltage protection
is triggered and then both UGATE and LGATE gate drivers
are forced low. There is a 2.5μs delay built into the under
voltage protection circuit to prevent false transitions. During
soft-start, the UVP blanking time is 2.5ms.
Output Voltage Setting (FB)
The output voltage can be adjusted from 0.75V to 3.3V by
setting the feedback resistor R1 and R2 (Figure 4). Choose
R2 to be approximately 10kΩ, and solve for R1 using the
equation :
⎛ R1 ⎞
VOUT = VREF × ⎜ 1+
⎟
⎝ R2 ⎠
where VREF is 0.75V.(typ.)
VIN
VOUT
UGATE
PHASE
LGATE
VOUT
FB
R1
R2
GND
Figure 4. Setting VOUT with a Resistor-Divider
Output Inductor Selection
The switching frequency (on-time) and operating point (%
ripple or LIR) determine the inductor value as follows :
t × ( VIN − VOUT )
L = ON
LIR × ILOAD(MAX)
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
13
RT8209L/M
Where LIR is the ratio of peak-of-peak ripple current to the
maximum average inductor current. Find a low pass
inductor having the lowest possible DC resistance that
fits in the allowed dimensions. Ferrite cores are often the
best choice, although powdered iron is inexpensive and
can work well at 200kHz. The core must be large enough
and not to saturate at the peak inductor current (IPEAK) :
⎡⎛ L
IPEAK = ILOAD(MAX) + ⎢⎜ IR
⎣⎝ 2
⎤
⎞
⎟ × ILOAD(MAX) ⎥
⎠
⎦
Output Capacitor Selection
The output filter capacitor must have low enough Equivalent
Series Resistance (ESR) to meet output ripple and loadtransient requirements, yet have high enough ESR to
satisfy stability requirements. The output capacitance
must also be high enough to absorb the inductor energy
while transiting from full-load to no-load conditions without
tripping the overvoltage fault latch.
Although Mach ResponseTM DRVTM dual ramp valley mode
provides many advantages such as ease-of-use, minimum
external component configuration, and extremely short
response time, due to not employing an error amplifier in
the loop, a sufficient feedback signal needs to be provided
by an external circuit to reduce the jitter level. The required
signal level is approximately 15mV at the comparing point.
This generates VRipple = (VOUT / 0.75) x 15mV at the output
node. The output capacitor ESR should meet this
requirement.
Output Capacitor Stability
Stability is determined by the value of the ESR zero relative
to the switching frequency. The point of instability is given
by the following equation :
f
1
fESR =
≤ SW
2 × π × ESR × COUT
4
Do not put high value ceramic capacitors directly across
the outputs without taking precautions to ensure stability.
Large ceramic capacitors can have a high-ESR zero
frequency and cause erratic and unstable operation.
However, it is easy to add sufficient series resistance by
placing the capacitors a couple of inches downstream from
the inductor and connecting VOUT or FB divider close to
the inductor. There are two related but distinct ways
including double pulsing and feedback loop instability to
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
14
identify the unstable operation. Double pulsing occurs due
to noise on the output or because the ESR is too low that
there is not enough voltage ramp in the output voltage
signal. This “fools” the error comparator into triggering a
new cycle immediately after a 400ns minimum off-time
period has expired. Double pulsing is more annoying than
harmful, resulting in nothing worse than increased output
ripple. However, it may indicate the possible presence of
loop instability, which is caused by insufficient ESR. Loop
instability can result in oscillation at the output after line
or load perturbations that can trip the over voltage
protection latch or cause the output voltage to fall below
the tolerance limit. The easiest method for stability
checking is to apply a very zero-to-max load transient
and carefully observe the output voltage ripple envelope
for overshoot and ringing. It helps to simultaneously monitor
the inductor current with AC probe. Do not allow more
than one ringing cycle after the initial step-response underor over shoot.
Thermal Considerations
For continuous operation, do not exceed absolute
maximum operation junction temperature. The maximum
power dissipation depends on the thermal resistance of
IC package, PCB layout, the rate of surroundings airflow
and temperature difference between junction to ambient.
The maximum power dissipation can be calculated by
following formula :
PD(MAX) = ( TJ(MAX) − TA ) / θJA
Where T J(MAX) is the maximum operation junction
temperature 125°C, TA is the ambient temperature and
the θJA is the junction to ambient thermal resistance.
For recommended operating conditions specification of
RT8209L/M, where TJ(MAX) is the maximum junction
temperature of the die (125°C) and TA is the maximum
ambient temperature. The junction to ambient thermal
resistance θJA is layout dependent. For WQFN-16L 3x3
packages, the thermal resistance θJA is 68°C/W on the
standard JEDEC 51-7 four layers thermal test board. For
WQFN-14L 3.5x3.5 packages, the thermal resistance θJA
is 60°C/W on the standard JEDEC 51-7 four layers thermal
test board. The maximum power dissipation at TA = 25°C
can be calculated by following formula :
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
PD(MAX) = (125°C − 25°C) / (68°C/W) = 1.471W for
WQFN-16L 3x3 packages
PD(MAX) = (125°C − 25°C) / (60°C/W) = 1.667W for
WQFN-14L 3.5x3.5 packages
The maximum power dissipation depends on operating
ambient temperature for fixed T J(MAX) and thermal
resistance θJA. For RT8209L/M packages, the Figure 5
of derating curves allows the designer to see the effect of
rising ambient temperature on the maximum power
allowed.
Maximum Power Dissipation (W)1
1.8
Layout Considerations
Layout is very important in high frequency switching
converter design. If the layout is designed improperly, the
PCB could radiate excessive noise and contribute to the
converter instability. The following points must be followed
for a proper layout of RT8209L/M.
`
Connect an RC low pass filter from VDDP to VDD, 1μF
and 10Ω are recommended. Place the filter capacitor
close to the IC.
`
Keep current limit setting network as close as possible
to the IC. Routing of the network should avoid coupling
to high-voltage switching node.
`
Connections from the drivers to the respective gate of
the high side or the low side MOSFET should be as
short as possible to reduce stray inductance.
`
All sensitive analog traces and components such as
VOUT, FB, GND, EN/DEM, PGOOD, CS, VDD, and TON
should be placed away from high voltage switching
nodes such as PHASE, LGATE, UGATE, or BOOT
nodes to avoid coupling. Use internal layer (s) as ground
plane (s) and shield the feedback trace from power traces
and components.
`
Current sense connections must always be made using
Kelvin connections to ensure an accurate signal, with
the current limit resistor located at the device.
`
Power sections should connect directly to ground plane
(s) using multiple vias as required for current handling
(including the chip power ground connections). Power
components should be placed to minimize loops and
reduce losses.
Four Layers PCB
1.6
1.4
WQFN -14L 3.5x3.5
1.2
1.0
WQFN -16L 3x3
0.8
0.6
0.4
0.2
0.0
0
25
50
75
100
125
Ambient Temperature (°C)
Figure 5. Derating Curves for RT8209L/M Packages
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
DS8209L/M-07 January 2014
is a registered trademark of Richtek Technology Corporation.
www.richtek.com
15
RT8209L/M
Outline Dimension
D
SEE DETAIL A
D2
L
1
E
E2
b
e
1
2
2
DETAIL A
Pin #1 ID and Tie Bar Mark Options
A
A1
1
A3
Note : The configuration of the Pin #1 identifier is optional,
but must be located within the zone indicated.
Dimensions In Millimeters
Dimensions In Inches
Symbol
Min
Max
Min
Max
A
0.700
0.800
0.028
0.031
A1
0.000
0.050
0.000
0.002
A3
0.175
0.250
0.007
0.010
b
0.180
0.300
0.007
0.012
D
2.950
3.050
0.116
0.120
D2
1.300
1.750
0.051
0.069
E
2.950
3.050
0.116
0.120
E2
1.300
1.750
0.051
0.069
e
L
0.500
0.350
0.020
0.450
0.014
0.018
W-Type 16L QFN 3x3 Package
Copyright © 2014 Richtek Technology Corporation. All rights reserved.
www.richtek.com
16
is a registered trademark of Richtek Technology Corporation.
DS8209L/M-07 January 2014
RT8209L/M
1
1
2
2
DETAIL A
Pin #1 ID and Tie Bar Mark Options
Note : The configuration of the Pin #1 identifier is optional,
but must be located within the zone indicated.
Symbol
Dimensions In Millimeters
Dimensions In Inches
Min
Max
Min
Max
A
0.700
0.800
0.028
0.031
A1
0.000
0.050
0.000
0.002
A3
0.175
0.250
0.007
0.010
b
0.180
0.300
0.007
0.012
D
3.400
3.600
0.134
0.142
D2
1.950
2.150
0.077
0.085
E
3.400
3.600
0.134
0.142
E2
1.950
2.150
0.077
0.085
e
0.500
0.020
e1
1.500
0.060
L
0.300
0.500
0.012
0.020
W-Type 14L QFN 3.5x3.5 Package
Richtek Technology Corporation
14F, No. 8, Tai Yuen 1st Street, Chupei City
Hsinchu, Taiwan, R.O.C.
Tel: (8863)5526789
Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should
obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot
assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be
accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries.
DS8209L/M-07 January 2014
www.richtek.com
17