NS ESI G D W EN T R NE D FO PLACEM ter at E D Cen /tsc M EN D RE Sheet COM MENDE SupportData E R l.com NOT RECOM chnical w.intersi NO r Te ww ct ou RSIL or a t n E co T 8-IN 1-88 18-Channel TFT-LCD Reference Voltage EL5525 ® Generator September 21, 2010 FN7393.2 Features • 18-channel Reference Outputs The EL5525 is designed to produce the reference voltages required in TFT-LCD applications. Each output is programmed to the required voltage with 10 bits of resolution. Reference pins determine the high and low voltages of the output range, which are capable of swinging to either supply rail. Programming of each output is performed using the serial interface. A serial out pin enables daisy chaining of multiple devices. A number of the EL5525 can be stacked for applications requiring more than 18 outputs. The reference inputs can be tied to the rails, enabling each part to output the full voltage range, or alternatively, they can be connected to external resistors to split the output range and enable finer resolutions of the outputs. The EL5525 has 18 outputs and comes in a 38-pin HTSSOP package. It is specified for operation over the full -40°C to +85°C temperature range. Ordering Information • Accuracy of ±0.1% • Supply Voltage of 4.5V to 16.5V • Digital Supply 3.3V to 5V • Low Supply Current of 15mA • Rail-to-Rail Capability • Internal Thermal Protection • Pb-Free Available (RoHS Compliant) Applications • TFT-LCD Drive Circuits • Reference Voltage Generators Pinout EL5525 (38-PIN HTSSOP) TOP VIEW PKG. DWG. NUMBER ENA 1 38 OUTA SDI 2 37 OUTB EL5525IREZ* 5525IREZ -40 to +85 38-Pin HTSSOP MDP0048 SCLK 3 36 OUTC EL5525IREZ-T7* 5525IREZ -40 to +85 38-Pin HTSSOP MDP0048 SDO 4 EL5525IREZ-T13* 5525IREZ -40 to +85 38-Pin HTSSOP MDP0048 EXT_OSC 5 34 OUTD VS 6 33 OUTE VSD 7 32 OUTF NC 8 31 OUTG PART NUMBER (Note) PART MARKING TEMP RANGE (°C) PACKAGE (Pb-free) *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 30 OUTH NC 9 OSC_SELECT 10 VS 11 1 35 GND THERMAL PAD 29 OUTI 28 GND REFH 12 27 OUTJ REFL 13 26 OUTK GND 14 25 OUTL CAP 15 24 GND VS 16 23 OUTM NC 17 22 OUTN OUTR 18 21 OUTO OUTQ 19 20 OUTP CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004-2005, 2010. All Rights Reserved All other trademarks mentioned are the property of their respective owners. EL5525 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage Between VS and GND . . . . . . . . . . . . . . . . 4.5V(min) to 18V(max) Between VSD and GND . . . . . . . . . . . 3V(min) to VS and +7(max) Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS = 15V, VSD = 5V, VREFH = 13V, VREFL = 2V, RL = 1.5kΩ and CL = 200pF to 0V, TA = +25°C, unless otherwise specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT 15 18 mA 0.17 0.35 mA 50 150 mV SUPPLY IS Supply Current ISD Digital Supply Current No load ANALOG VOL Output Swing Low Sinking 5mA (VREFH = 15V, VREFL = 0) VOH Output Swing High Sourcing 5mA (VREFH = 15V, VREFL = 0) ISC Short Circuit Current PSRR Power Supply Rejection Ratio 14.85 14.95 V RL = 10Ω 100 140 mA VS+ is moved from 14V to 16V 45 60 dB tD Program to Out Delay 4 ms VAC Accuracy Referred to the Ideal Value Code = 512 20 mV ΔVMIS Channel to Channel Mismatch Code = 512 2 mV VDROOP Droop Voltage 1 RINH Input Resistance @ VREFH, VREFL REG Load Regulation BG Band Gap 2 mV/ms 0.5 1.5 mV/mA 1.3 1.6 V 34 IOUT = 5mA step 1.1 kΩ DIGITAL VIH Logic 1 Input Voltage VIL Logic 0 Input Voltage 1 V FCLK Clock Frequency 5 MHz tS Setup Time 20 ns tH Hold Time 20 ns tLC Load to Clock Time 20 ns tCE Clock to Load Line 20 ns tDCO Clock to Out Delay Time 10 ns RSDIN SDIN Input Resistance 1 GΩ TPULSE Minimum Pulse Width for EXT_OSC Signal 5 µs Duty Cycle Duty Cycle for EXT_OSC Signal F_OSC Internal Refresh Oscillator Frequency INL DNL 2 Negative edge of SCLK V 50 % 21 kHz Integral Nonlinearity Error 1.3 LSB Differential Nonlinearity Error 0.5 LSB 2 OSC_Select = 0 FN7393.2 September 21, 2010 EL5525 Pin Descriptions PIN NUMBER PIN NAME PIN TYPE 1 ENA Logic Input Chip select, low enables data input to logic 2 SDI Logic Input Serial data input 3 SCLK Logic Input Serial data clock 4 SDO Logic Output Serial data output 5 EXT_OSC Input/Output Oscillator pin for synchronizing 6, 11, 16 VS Power Positive supply voltage for analog circuits (4.5V to 16.5V) 7 VSD Power Positive power supply for digital circuites (3.3V to 5V) 8, 9, 17 NC 10 OSC_SELECT 12 REFH Analog Input High reference voltage 13 REFL Analog Input Low reference voltage 14, 24, 28, 35 GND Power Ground 15 CAP Analog Decoupling capacitor for internal reference 18 OUTR Analog Output Channel R output voltage 19 OUTQ Analog Output Channel Q output voltage 20 OUTP Analog Output Channel P output voltage 21 OUTO Analog Output Channel O output voltage 22 OUTN Analog Output Channel N output voltage 23 OUTM Analog Output Channel M output voltage 25 OUTL Analog Output Channel L output voltage 26 OUTK Analog Output Channel K output voltage 27 OUTJ Analog Output Channel J output voltage 29 OUTI Analog Output Channel I output voltage 30 OUTH Analog Output Channel H output voltage 31 OUTG Analog Output Channel G output voltage 32 OUTF Analog Output Channel F output voltage 33 OUTE Analog Output Channel E output voltage 34 OUTD Analog Output Channel D output voltage 36 OUTC Analog Output Channel C output voltage 37 OUTB Analog Output Channel B output voltage 38 OUTA Analog Output Channel A output voltage 3 PIN DESCRIPTION Not connected Oscillator select, “0” = internal, “1” = external FN7393.2 September 21, 2010 EL5525 REFH = 13V, REFL = 2V 0.3 1.5 0.2 1 0.1 INL (LSB) DIFFERENTIAL NONLINEARITY (LSB) Typical Performance Curves 0 -0.1 -0.2 0.5 0 -0.5 VS = 15V VSD = 5V -0.3 10 VREFH = 13V VREFL = 2V 210 410 -1 610 810 0 1010 200 400 600 800 1000 1200 CODE INPUT CODE FIGURE 1. DIFFERENTIAL NONLINEARITY vs CODE FIGURE 2. INTEGRAL NONLINEARITY ERROR VS = VREFH = 15V VS = VREFH = 15V 0mA 5mA/DIV 5mA 0mA 5mA 5mA/DIV CL= 4.7nF RS = 20Ω CL=1nF RS = 20Ω 5V 200mV/DIV 200mV/DIV CL = 1nF RS = 20Ω CL= 4.7nF RS = 20Ω CL = 180pF CL= 180pF M = 400ns/DIV M = 400ns/DIV FIGURE 3. TRANSIENT LOAD REGULATION (SOURCING) FIGURE 4. TRANSIENT LOAD REGULATION (SINKING) SCLK SCLK SDA SDA ENA ENA OUTA OUTA M = 200µs/DIV M = 200µs/DIV FIGURE 5. LARGE SIGNAL RESPONSE (RISING FROM 0V TO 8V) 4 FIGURE 6. SMALL SIGNAL RESPONSE (FALLING FROM 200mV TO 100mV) FN7393.2 September 21, 2010 EL5525 General Description together, connect the SDO pin to the SDI pin on the next chip. While the ENA is held low, the 16m-bit data is loaded to the SDI input of the first chip. The first 16-bit data will go to the last chip and the last 16-bit data will go to the first chip. While the ENA is held high, all addressed outputs will be updated simultaneously. The EL5525 provides a versatile method of providing the reference voltages that are used in setting the transfer characteristics of LCD display panels. The V/T (Voltage/Transmission) curve of the LCD panel requires that a correction is applied to make it linear; however, if the panel is to be used in more than one application, the final curve may differ for different applications. By using the EL5525, the V/T curve can be changed to optimize its characteristics according to the required application of the display product. Each of the eight reference voltage outputs can be set with a 10-bit resolution. These outputs can be driven to within 50mV of the power rails of the EL5525. As all of the output buffers are identical, it is also possible to use the EL5525 for applications other than LCDs where multiple voltage references are required that can be set to 10 bit accuracy. The Serial Timing Diagram and parameters table show the timing requirements for three-wire signals. The serial data has a minimum length of 16 bits, the MSB (most significant bit) is the first bit in the signal. The bits are allocated to the following functions (also refer to Table 1). • Bit 15 is always set to a zero • Bits 14 through 10 select the channel to be written to, these are binary coded with channel A = 0, and channel R = 17 • The 10-bit data is on bits 9 through 0. Some examples of data words are shown in Table 3. Digital Interface The EL5525 uses a simple 3-wire SPI compliant digital interface to program the outputs. The EL5525 can support the clock rate up to 5MHz. TABLE 1. CONTROL BITS LOGIC TABLE Serial Interface The EL5525 is programmed through a three-wire serial interface. The start and stop conditions are defined by the ENA signal. While the ENA is low, the data on the SDI (serial data input) pin is shifted into the 16-bit shift register on the positive edge of the SCLK (serial clock) signal. The MSB (bit 15) is loaded first and the LSB (bit 0) is loaded last (see Table 1). After the full 16-bit data has been loaded, the ENA is pulled high and the addressed output channel is updated. The SCLK is disabled internally when the ENA is high. The SCLK must be low before the ENA is pulled low. BIT NAME B15 Test Always 0 DESCRIPTION B14 A4 Channel Address B13 A3 Channel Address B12 A2 Channel Address B11 A1 Channel Address B10 A0 Channel Address B9 D9 Data B8 D8 Data B7 D7 Data B6 D6 Data To facilitate the system designs that use multiple EL5525 chips, a buffered serial output of the shift register (SDO pin) is available. Data appears on the SDO pin at the 16th falling SCLK edge after being applied to the SDI pin. B5 D5 Data B4 D4 Data B3 D3 Data B2 D2 Data To control the multiple EL5525 chips from a single three-wire serial port, just connect the ENA pins and the SCLK pins B1 D1 Data B0 D0 Data Serial Timing Diagram ENA tHE tSE tr T tf tHE tSE SCLK tSD tHD B15 SDI MSB 5 tw B14 B13 LOAD MSB FIRST, LSB LAST B12-B2 B1 B0 LSB t FN7393.2 September 21, 2010 EL5525 TABLE 2. SERIAL TIMING PARAMETERS PARAMETER RECOMMENDED OPERATING RANGE DESCRIPTION T ≥200ns Clock Period tr/tf 0.05 * T Clock Rise/Fall Time tHE ≥10ns ENA Hold Time tSE ≥10ns ENA Setup Time tHD ≥10ns Data Hold Time tSD ≥10ns Data Setup Time tW 0.50 * T Clock Pulse Width TABLE 3. SERIAL PROGRAMMING EXAMPLES Control Channel Address Data C1 A4 A3 A2 A1 A0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Channel A, Value = 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 Channel A, Value = 1023 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 Channel A, Value = 512 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 Channel C, Value = 513 0 0 0 1 1 1 0 0 0 0 0 1 1 1 1 1 Channel H, Value = 31 0 1 0 0 0 1 0 0 0 0 0 1 1 1 1 1 Channel R, Value = 31 Analog Section Transfer Function The transfer function is: shown in Equaion 1: data V OUT ( IDEAL ) = V REFL + ------------- × ( V REFH - V REFL ) 1024 (EQ. 1) where data is the decimal value of the 10-bit data binary input code. The output voltages from the EL5525 will be derived from the reference voltages present at the VREFL and VREFH pins. The impedance between those two pins is about 32kΩ. Condition For transient load application, the external clock Mode should be used to ensure all functions are synchronized together. The positive edge of the external clock to the OSC pin should be timed to avoid the transient load effect. The Application Drawing shows the LCD H rate signal used, here the positive clock edge is timed to avoid the transient load of the column driver circuits. After power on, the chip will start with the internal oscillator mode. At this time, the EXT_OSC pin will be in a high impedance condition to prevent contention. By setting pin 10 to high, the chip is on external clock mode. Setting pin 10 to low, the chip is on internal clock mode. Care should be taken that the system design holds these two reference voltages within the limits of the power rails of the EL5525. GND < VREFH ≤ VS and GND ≤ VREFL ≤ VREFH. Clock Oscillator The EL5525 requires an internal clock or external clock to refresh its outputs. The outputs are refreshed at the falling OSC clock edges. The output refreshed switches open at the rising edges of the OSC clock. The driving load shouldn’t be changed at the rising edges of the OSC clock. Otherwise, it will generate a voltage error at the outputs. This clock may be input or output via the clock pin labeled EXT_OSC. The internal clock is provided by an internal oscillator running at approximately 21kHz and can be output to the EXT_OSC pin. In a 2 chip system, if the driving loads are stable, one chip may be programmed to use the internal oscillator; then the OSC pin will output the clock from the internal oscillator. The second chip may have the OSC pin connected to this clock source. 6 FN7393.2 September 21, 2010 EL5525 Block Diagram REFH OUTA OUTB OUTC OUTD 18 CHANNEL REGISTERS VOLTAGE SOURCES OUTE OUTP OUTQ OUTR REFL CAP SDO SDI SCLK CONTROL IF ENA OSC_SELECT Channel Outputs Each of the channel outputs has a rail-to-rail buffer. This enables all channels to have the capability to drive to within 50mV of the power rails, (see Table Electrical Specifications on page 2 for details). When driving large capacitive loads, a series resistor should be placed in series with the output. (Usually between 5Ω and 50Ω). Each of the channels is updated on a continuous cycle, the time for the new data to appear at a specific output will depend on the exact timing relationship of the incoming data to this cycle. The best-case scenario is when the data has just been captured and then passed on to the output stage immediately; this can be as short as 48µs. In the worst-case scenario, this will be 860µs for EL5525, when the data has just missed the cycle at f_OSC = 21kHz. When a large change in output voltage is required, the change will occur in 2V steps, thus the requisite number of timing cycles will be added to the overall update time. This means that a large change of 16V can take between 6.8ms and 7.2ms depending on the absolute timing relative to the update cycle. 7 EXT_OSC Output Stage and the Use of External Oscillator CH 1.3V VIN + - + - S1 1.3V + - VOUT S2 OSC FIGURE 7. SIMPLIFIED OUTPUT SAMPLE AND HOLD AMP STAGE FOR ONE CHANNEL The output voltage is generated from the DAC, which is VIN in Figure 7. The refreshed switches are controlled by the internal or external oscillator signal. When the OSC clock signal is low, switches S1 and S2 are closed. The output VOUT = VIN and at the same time the sample and hold cap CH is being charged. When the OSC clock signal is high, the refreshed switches S1 and S2 are opened and the output voltage is maintained by CH. This refreshed process will repeat every 18 clock cycles for each channel. The time FN7393.2 September 21, 2010 EL5525 takes to update the output depends on the timing at the VIN and the state of the switches. It can take 1 to 18 clock cycles to update each output. For the sample and hold capacitor CH to maintain the correct output voltage, the driving load shouldn’t be changed at the rising edge of the OSC signal. Since at the rising edge of the OSC clock, the refreshed switches are being opened, if the load changes at that time, it will generate an error output voltage. For a fixed load condition, the internal oscillator can be used. For the transient load condition, the external OSC mode should be used to avoid the conflict between the rising edge of the OSC signal and the changing load. So a timing delay circuit will be needed to delay the OSC signal and avoid the rising edge of the OSC signal and changing the load at the same time. Ch1 --- Output1 Ch3 --- Output2 Ch2 --- EXT_OSC At the falling edge of the OSC, output 1 is being refreshed, and one clock cycle later, output 2 is being refreshed. The spike you see here is the response of the output amplifier when the refreshed switches are closed. When driving a big capacitor load, there will be ringing at the spikes because the phase margin of the amplifier is decreased. The speed of the external OSC signal shouldn’t be greater than 70kHz because for the worst condition, it will take at least 4µs to charge the sample and hold capacitor CH. The pulse width has to be at least 4µs long. From our lab test, the duty cycle of the OSC signal must be greater than 30%. POWER DISSIPATION With the 30mA maximum continues output drive capability for each channel, it is possible to exceed the +125°C absolute maximum junction temperature. Therefore, it is important to calculate the maximum junction temperature for the application to determine if load conditions need to be modified for the part to remain in the safe operation. The maximum power dissipation allowed in a package is determined according to: Equation 2: T JMAX - T AMAX P DMAX = --------------------------------------------Θ JA FIGURE 8. TRANSIENT LOAD RESPONSE (EQ. 2) where: Channel 3 --- sinking and sourcing 5mA current • TJMAX = Maximum junction temperature Channel 2 --- EXT_OSC signal • TAMAX = Maximum ambient temperature • θJA = Thermal resistance of the package Channel 1 --- VOUT In Figure Table 8 on page 8, the OSC signal is synchronized to the load signal. The rising edge of the OSC signal is then delayed by some amount of time and gives enough time for CH to be charged to a new voltage before the switches are opened. • PDMAX = Maximum power dissipation in the package The maximum power dissipation actually produced by the IC is the total quiescent supply current times the total power supply voltage and plus the power in the IC due to the loads. P DMAX = V S × I S + Σ [ ( V S - V OUT i ) × I LOAD i ] (EQ. 3) when sourcing, and: P DMAX = V S × I S + Σ ( V OUT i × I LOAD i ) (EQ. 4) when sinking. Where: • i = 18 • VS = Supply voltage FIGURE 9. CHANNEL TO CHANNEL REFRESH • IS = Quiescent current • VOUTi = Output voltage of the i channel • ILOADi = Load current of the i channel 8 FN7393.2 September 21, 2010 EL5525 POWER SUPPLY BYPASSING AND PRINTED CIRCUIT BOARD LAYOUT By setting the two PDMAX equations equal to each other, we can solve for the RLOADs to avoid the device overheat. The package power dissipation curves provide a convenient way to see if the device will overheat. Good printed circuit board layout is necessary for optimum performance. A low impedance and clean analog ground plane should be used for the EL5525. The traces from the two ground pins to the ground plane must be very short. The thermal pad of the EL5525 should be connected to the analog ground plane. Lead length should be as short as possible and all power supply pins must be well bypassed. A 0.1µF ceramic capacitor must be place very close to the VS, VREFH, VREFL, and CAP pins. A 4.7µF local bypass tantalum capacitor should be placed to the VS, VREFH, and VREFL pins. THERMAL SHUTDOWN The EL5525 has an internal thermal shutdown circuitry that prevents overheating of the part. When the junction temperature goes up to about +150°C, the part will be disabled. When the junction temperature drops down to about +120°C, the part will be enabled. With this feature, any short circuit at the outputs will enable the thermal shutdown circuitry to disable the part. Application Drawing +10V HIGH REFERENCE VOLTAGE REFH OUTA VS OUTB 0.1µF +12V COLUMN (SOURCE) DRIVER 0.1µF +5V MICROCONTROLLER VSD OUTC LCD PANEL 0.1µF OUTD SDI SCK LCD TIMING CONTROLLER ENA SDO HORIZONTAL RATE OUTE OSC OUTF CAP 0.1µF +1V 0.1µF 5V OSC_SET OUTQ REFL GND OUTR EL5525 9 FN7393.2 September 21, 2010 EL5525 HTSSOP (Heat-Sink TSSOP) Family MDP0048 0.25 M C A B D HTSSOP (HEAT-SINK TSSOP) FAMILY A (N/2)+1 N MILLIMETERS SYMBOL 14 LD 20 LD 24 LD 28 LD 38 LD TOLERANCE PIN #1 I.D. E E1 0.20 C B A 1 2X N/2 LEAD TIPS (N/2) TOP VIEW B D1 EXPOSED THERMAL PAD E2 1.20 1.20 1.20 1.20 Max 0.075 0.075 0.075 0.075 ±0.075 A2 0.90 0.90 0.90 0.90 0.90 +0.15/-0.10 b 0.25 0.25 0.25 0.25 0.22 +0.05/-0.06 c 0.15 0.15 0.15 0.15 0.15 +0.05/-0.06 D 5.00 6.50 7.80 9.70 9.70 ±0.10 D1 3.2 4.2 4.3 5.0 7.25 Reference E 6.40 6.40 6.40 6.40 6.40 Basic E1 4.40 4.40 4.40 4.40 4.40 ±0.10 E2 3.0 3.0 3.0 3.0 3.0 Reference e 0.65 0.65 0.65 0.65 0.50 Basic L 0.60 0.60 0.60 0.60 0.60 ±0.15 L1 1.00 1.00 1.00 1.00 1.00 Reference N 14 20 24 28 38 Reference NOTES: 0.05 e 1.20 0.075 Rev. 3 2/07 BOTTOM VIEW C A A1 H 1. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15mm per side. 2. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm per side. SEATING PLANE 0.10 C N LEADS 3. Dimensions “D” and “E1” are measured at Datum Plane H. 0.10 M C A B b 4. Dimensioning and tolerancing per ASME Y14.5M-1994. SIDE VIEW SEE DETAIL “X” c END VIEW L1 A A2 GAUGE PLANE 0.25 L A1 0° - 8° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 10 FN7393.2 September 21, 2010