X9C102, X9C103, X9C104, X9C503
®
Data Sheet
December 20, 2006
FN8222.1
DESCRIPTION
Digitally Controlled Potentiometer
(XDCP™)
FEATURES
• Solid-state potentiometer
• 3-wire serial interface
• 100 wiper tap points
—Wiper position stored in nonvolatile memory
and recalled on power-up
• 99 resistive elements
—Temperature compensated
—End to end resistance, ±20%
—Terminal voltages, ±5V
• Low power CMOS
—VCC = 5V
—Active current, 3mA max.
—Standby current, 750µA max.
• High reliability
—Endurance, 100,000 data changes per bit
—Register data retention, 100 years
• X9C102 = 1kΩ
• X9C103 = 10kΩ
• X9C503 = 50kΩ
• X9C104 = 100kΩ
• Packages
—8 Ld SOIC and 8 Ld PDIP
• Pb-free plus anneal available (RoHS compliant)
The X9Cxxx are Intersil digitally controlled (XDCP)
potentiometers. The device consists of a resistor
array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by a
three-wire interface.
The potentiometer is implemented by a resistor array
composed of 99 resistive elements and a wiper switching network. Between each element and at either end
are tap points accessible to the wiper terminal. The
position of the wiper element is controlled by the CS,
U/D, and INC inputs. The position of the wiper can be
stored in nonvolatile memory and then be recalled
upon a subsequent power-up operation.
The device can be used as a three-terminal potentiometer or as a two-terminal variable resistor in a wide
variety of applications including:
– control
– parameter adjustments
– signal processing
BLOCK DIAGRAM
U/D
INC
CS
7-Bit
Up/Down
Counter
VCC (Supply Voltage)
RH/VH
99
98
97
Up/Down
(U/D)
Increment
(INC)
Device
Select (CS)
7-Bit
Nonvolatile
Memory
VH/RH
Control
and
Memory
RW/VW
VL/RL
VSS (Ground)
VCC
GND
General
Store and
Recall
Control
Circuitry
96
One
of
OneHundred
Decoder
2
Transfer
Gates
Resistor
Array
1
0
RL/VL
RW/VW
Detailed
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005, 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X9C102, X9C103, X9C104, X9C503
PIN CONFIGURATION
DIP/SOIC
INC
1
8
VCC
U/D
2
7
CS
VH/RH
3
6
VL/RL
VSS
4
5
VW/RW
X9C102/103/104/503
ORDERING INFORMATION
PART NUMBER
PART MARKING
RTOTAL
(kΩ)
TEMPERATURE RANGE
(°C)
1
PACKAGE
PKG. DWG. #
X9C102P
X9C102P
0 to 70
8 Ld PDIP
MDP0031
X9C102PZ (Note)
X9C102P Z
0 to 70
8 Ld PDIP (Pb-free)
MDP0031
X9C102PI
X9C102P I
-40 to 85
8 Ld PDIP
MDP0031
X9C102PIZ (Note)
X9C102P ZI
-40 to 85
8 Ld PDIP (Pb-free)
MDP0031
X9C102S*, **
X9C102S
0 to 70
8 Ld SOIC
MDP0027
X9C102SZ* (Note)
X9C102S Z
0 to 70
8 Ld SOIC (Pb-free)
MDP0027
X9C102SI*, **
X9C102S I
-40 to 85
8 Ld SOIC
MDP0027
X9C102SIZ*, ** (Note)
X9C102S ZI
-40 to 85
8 Ld SOIC (Pb-free)
MDP0027
X9C103P
X9C103P
0 to 70
8 Ld PDIP
MDP0031
10
X9C103PZ (Note)
X9C103P Z
0 to 70
8 Ld PDIP (Pb-free)
MDP0031
X9C103PI
X9C103P I
-40 to 85
8 Ld PDIP
MDP0031
X9C103PIZ (Note)
X9C103P ZI
-40 to 85
8 Ld PDIP (Pb-free)
MDP0031
X9C103S*, **
X9C103S
0 to 70
8 Ld SOIC
MDP0027
X9C103S Z
0 to 70
8 Ld SOIC (Pb-free)
MDP0027
X9C103SI*, **
X9C103S I
-40 to 85
8 Ld SOIC
MDP0027
X9C103SIZ*, ** (Note)
X9C103S ZI
-40 to 85
8 Ld SOIC (Pb-free)
MDP0027
X9C103SZ*, **
(Note)
X9C503P
X9C503P
0 to 70
8 Ld PDIP
MDP0031
X9C503PZ (Note)
X9C503P Z
50
0 to 70
8 Ld PDIP (Pb-free)
MDP0031
X9C503PI
X9C503P I
-40 to 85
8 Ld PDIP
MDP0031
X9C503PIZ (Note)
X9C503P ZI
-40 to 85
8 Ld PDIP (Pb-free)
MDP0031
X9C503S*
X9C503S
0 to 70
8 Ld SOIC
MDP0027
X9C503SZ* (Note)
X9C503S Z
0 to 70
8 Ld SOIC (Pb-free)
MDP0027
X9C503SI*, **
X9C503S I
-40 to 85
8 Ld SOIC
MDP0027
X9C503SIZ*, ** (Note)
X9C503S ZI
-40 to 85
8 Ld SOIC (Pb-free)
MDP0027
X9C104P
X9C104P
0 to 70
8 Ld PDIP
MDP0031
X9C104PI
X9C104P I
-40 to 85
8 Ld PDIP
MDP0031
X9C104PIZ (Note)
X9C104P ZI
-40 to 85
8 Ld PDIP (Pb-free)
MDP0031
X9C104S*, **
X9C104S
0 to 70
8 Ld SOIC
MDP0027
X9C104SZ*, ** (Note)
X9C104S Z
0 to 70
8 Ld SOIC (Pb-free)
MDP0027
X9C104SI*, **
X9C104S I
-40 to 85
8 Ld SOIC
MDP0027
X9C104SIZ*, ** (Note)
X9C104S ZI
-40 to 85
8 Ld SOIC (Pb-free)
MDP0027
100
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
*Add "T1" suffix for tape and reel.
**Add "T2" suffix for tape and reel.
2
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
PIN DESCRIPTIONS
Pin
Symbol
Brief Description
1
INC
Increment . The INC input is negative-edge triggered. Toggling INC will move the wiper and either
increment or decrement the counter in the direction indicated by the logic level on the U/D input.
2
U/D
Up/Down. The U/D input controls the direction of the wiper movement and whether the counter
is incremented or decremented.
3
RH/VH
4
VSS
5
VW/RW
VW/RW. VW/RW is the wiper terminal, and is equivalent to the movable terminal of a mechanical
potentiometer. The position of the wiper within the array is determined by the control inputs. The
wiper terminal series resistance is typically 40Ω.
6
RL/VL
RL/VL. The low (VL/RL) terminals of the X9C102/103/104/503 are equivalent to the fixed
terminals of a mechanical potentiometer. The minimum voltage is -5V and the maximum is +5V.
The terminology of VH/RH and VL/RL references the relative position of the terminal in
relation to wiper movement direction selected by the U/D input and not the voltage potential on
the terminal.
7
CS
CS. The device is selected when the CS input is LOW. The current counter value is stored in
nonvolatile memory when CS is returned HIGH while the INC input is also HIGH. After the store operation is complete the X9C102/103/104/503 device will be placed in the low power standby mode
until the device is selected once again.
8
VCC
VCC
RH/VH. The high (VH/RH) terminals of the X9C102/103/104/503 are equivalent to the fixed
terminals of a mechanical potentiometer. The minimum voltage is -5V and the maximum is +5V.
The terminology of VH/RH and VL/RL references the relative position of the terminal in
relation to wiper movement direction selected by the U/D input and not the voltage potential on
the terminal.
VSS
3
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
ABSOLUTE MAXIMUM RATINGS
COMMENT
Temperature under bias .................... -65°C to +135°C
Storage temperature ......................... -65°C to +150°C
Voltage on CS, INC, U/D and VCC
with respect to VSS .................................. -1V to +7V
Voltage on VH/RH and VL/RL
referenced to VSS ................................... -8V to +8V
ΔV = |VH/RH - VL/RL|
X9C102 ............................................................... 4V
X9C103, X9C503, and X9C104 ......................... 10V
Lead temperature (soldering, 10 seconds) ...... +300°C
IW (10 seconds) ................................................. 8.8mA
Power rating X9C102 ........................................ 16mW
Power rating X9C103/104/503 .......................... 10mW
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device (at these or any other conditions above those
listed in the operational sections of this specification) is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Min.
Max.
Supply Voltage (VCC)
Limits
0°C
+70°C
X9C102/103/104/503
5V ±10%
-40°C
+85°C
Commercial
Industrial
POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Symbol
Parameter
Min.
Typ.
Max.
Unit
RTOTAL
End to end resistance variation
-20
+20
%
VVH/RH
VH terminal voltage
-5
+5
V
VVL/RL
VL terminal voltage
-5
+5
V
-4.4
4.4
mA
IW
Wiper current
RW
Wiper resistance
40
Noise (5)
Resolution
Absolute
Relative
linearity(1)
linearity(2)
Ω
dBV
1
%
-1
-0.2
Wiper Current = ±1mA
Ref. 1kHz
+1
MI(3)
VW(n)(actual) - VW(n)(expected)
+0.2
MI(3)
VW(n + 1)(actual) - [VW(n) + MI]
RTOTAL temperature coefficient
±300(5)
ppm/°C
X9C103/503/104
RTOTAL temperature coefficient
±600(5)
ppm/°C
X9C102
±20
ppm/°C
10/10/25
pF
Ratiometric temperature coefficient
CH/CL/CW
100
-120
Test Conditions/Notes
Potentiometer capacitances
See Circuit #3, Macro Model
(5)
Notes: (1)
(2)
(3)
(4)
(5)
Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = [VW(n)(actual) - VW(n)(expected )] = ±1 MI Maximum.
Relative linearity is a measure of the error in step size between taps = VW(n + 1) - [VW(n) + MI] = +0.2 MI.
1 MI = Minimum Increment = RTOT/99
Typical values are for TA = +25°C and nominal supply voltage.
This parameter is not 100% tested.
4
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified.)
Limits
Symbol
Min. Typ.(4)
Parameter
ICC
VCC active current
ISB
Standby supply current
ILI
CS, INC, U/D input leakage
current
VIH
CS, INC, U/D input HIGH
voltage
VIL
CS, INC, U/D input LOW
voltage
CIN(5)
Max.
Unit
1
3
mA
CS = VIL, U/D = VIL or VIH and
INC = 0.4V to 2.4V @ max. tCYC
200
750
µA
CS = VCC - 0.3V, U/D and INC = VSS
or VCC - 0.3V
±10
µA
VIN = VSS to VCC
2
V
0.8
CS, INC, U/D input
capacitance
Test Conditions
10
V
pF
VCC = 5V, VIN = VSS, TA = 25°C, f = 1MHz
ENDURANCE AND DATA RETENTION
Parameter
Min.
Unit
Minimum endurance
100,000
Data changes per bit per register
Data retention
100
years
Test Circuit #1
Test Circuit #2
Test Circuit #3
Macro Model
VH/RH
V R /R H
Test Point
VS
Test Point
V W /R W
V L /R L
VW/RW
Force
Current
VL/RL
RTOTAL
RL
CL
10pF
RH
CH
CW
10pF
25pF
RW
A.C. CONDITIONS OF TEST
Input pulse levels
0V to 3V
Input rise and fall times
10ns
Input reference levels
1.5V
5
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
A.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified)
Limits
Symbol
tCl
tlD
tDI
tlL
tlH
tlC
tCPH
tCPH
tIW (5)
tCYC
tR, tF(5)
tPU(5)
tR VCC(5)
Parameter
CS to INC setup
INC HIGH to U/D change
U/D to INC setup
INC LOW period
INC HIGH period
INC inactive to CS inactive
CS deselect time (STORE)
CS deselect time (NO STORE)
INC to VW/RW change
INC cycle time
INC input rise and fall time
Power-up to wiper stable
VCC power-up rate
Typ.(6)
Min.
100
100
2.9
1
1
1
20
100
Max.
Unit
ns
ns
µs
µs
µs
µs
ms
ns
µs
µs
µs
µs
V/ms
100
2
500
500
0.2
50
POWER-UP AND DOWN REQUIREMENTS
At all times, voltages on the potentiometer pins must be less than ±VCC. The recall of the wiper position from nonvolatile memory is not in effect until the VCC supply reaches its final value. The VCC ramp rate spec is always in effect.
A.C. TIMING
CS
tCYC
tCI
tIL
tIC
tIH
tCPH
90%
90%
10%
INC
tID
tDI
tF
tR
U/D
tIW
MI
VW
(8)
Notes: (6) Typical values are for TA = 25°C and nominal supply voltage.
(7) This parameter is periodically sampled and not 100% tested.
(8) MI in the A.C. timing diagram refers to the minimum incremental change in the VW output due to a change in the wiper position.
6
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
PIN NAMES
DETAILED PIN DESCRIPTIONS
Symbol
RH/VH and RL/VL
The high (VH/RH) and low (VL/RL) terminals of the
X9C102/103/104/503 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum
voltage is -5V and the maximum is +5V. The terminology of VH/RH and VL/RL references the relative position
of the terminal in relation to wiper movement direction
selected by the U/D input and not the voltage potential
on the terminal.
RW/VW
VW/RW is the wiper terminal, and is equivalent to the
movable terminal of a mechanical potentiometer. The
position of the wiper within the array is determined by
the control inputs. The wiper terminal series resistance is
typically 40Ω.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling
INC will move the wiper and either increment or decrement the counter in the direction indicated by the logic
level on the U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW.
The current counter value is stored in nonvolatile
memory when CS is returned HIGH while the INC
input is also HIGH. After the store operation is complete the X9C102/103/104/503 device will be placed
in the low power standby mode until the device is
selected once again.
PIN CONFIGURATION
DIP/SOIC
INC
1
8
VCC
U/D
2
7
CS
VH/RH
3
6
VL/RL
VSS
4
5
VW/RW
X9C102/103/104/503
7
Description
VH /RH
High Terminal
VW/RW
Wiper Terminal
VL/RL
Low Terminal
VSS
Ground
VCC
Supply Voltage
U/D
Up/Down Control Input
INC
Increment Control Input
CS
Chip Select Control Input
NC
No Connection
PRINCIPLES OF OPERATION
There are three sections of the X9Cxxx: the input control, counter and decode section; the nonvolatile memory; and the resistor array. The input control section
operates just like an up/down counter. The output of
this counter is decoded to turn on a single electronic
switch connecting a point on the resistor array to the
wiper output. Under the proper conditions the contents
of the counter can be stored in nonvolatile memory
and retained for future use. The resistor array is comprised of 99 individual resistors connected in series. At
either end of the array and between each resistor is an
electronic switch that transfers the potential at that
point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the
last position. That is, the counter does not wrap
around when clocked to either extreme.
The electronic switches on the device operate in a
“make before break” mode when the wiper changes
tap positions. If the wiper is moved several positions,
multiple taps are connected to the wiper for tIW (INC to
VW/RW change). The RTOTAL value for the device can
temporarily be reduced by a significant amount if the
wiper is moved several positions.
When the device is powered-down, the last wiper position stored will be maintained in the nonvolatile memory. When power is restored, the contents of the
memory are recalled and the wiper is set to the value
last stored.
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
INSTRUCTIONS AND PROGRAMMING
The INC, U/D and CS inputs control the movement of
the wiper along the resistor array. With CS set LOW
the device is selected and enabled to respond to the
U/D and INC inputs. HIGH to LOW transitions on INC
will increment or decrement (depending on the state of
the U/D input) a seven-bit counter. The output of this
counter is decoded to select one of one-hundred wiper
positions along the resistive array.
The value of the counter is stored in nonvolatile memory whenever CS transitions HIGH while the INC input
is also HIGH.
The system may select the X9Cxxx, move the wiper,
and deselect the device without having to store the latest wiper position in nonvolatile memory. After the
wiper movement is performed as described above and
once the new position is reached, the system must
keep INC LOW while taking CS HIGH. The new wiper
position will be maintained until changed by the system or until a power-down/up cycle recalled the previously stored data.
This procedure allows the system to always power-up
to a preset value stored in nonvolatile memory; then
during system operation minor adjustments could be
made. The adjustments might be based on user preference: system parameter changes due to temperature drift, etc...
MODE SELECTION
CS
INC
U/D
Mode
L
H
Wiper Up
L
L
Wiper Down
H
X
Store Wiper Position
X
X
Standby Current
L
X
No Store, Return to Standby
L
H
Wiper Up (not recommended)
L
L
Wiper Down (not recommended)
H
SYMBOL TABLE
WAVEFORM
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from Low to
High
Will change
from Low to
High
May change
from High to
Low
Will change
from High to
Low
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A
Center Line
is High
Impedance
The state of U/D may be changed while CS remains
LOW. This allows the host system to enable the
device and then move the wiper up and down until the
proper trim is attained.
8
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
PERFORMANCE CHARACTERISTICS
Contact the factory for more information.
APPLICATIONS INFORMATION
Electronic digitally controlled (XCDP) potentiometers provide three powerful application advantages; (1) the variability
and reliability of a solid-state potentiometer, (2) the flexibility of computer-based digital controls, and (3) the retentivity
of nonvolatile memory used for the storage of multiple potentiometer settings or data.
Basic Configurations of Electronic Potentiometers
VR
VR
VH/RH
VW/RW
VL/RL
I
Three terminal potentiometer;
variable voltage divider
Two terminal variable resistor;
variable current
Basic Circuits
Buffered Reference Voltage
R1
+V
+V
Noninverting Amplifier
Cascading Techniques
+5V
+V
VS
+5V
VW
VREF
VOUT
–
-5V
X
VW/RW
R2
+V
-5V
R1
VW/RW
VOUT = VW/RW
(a)
Voltage Regulator
(b)
VO = (1+R2/R1)VS
Offset Voltage Adjustment
R1
VIN
VO (REG)
317
R2
VS
LT311A
100kΩ
–
10kΩ
10kΩ
+12V
10kΩ
-12V
R1
}
TL072
R2
VO
VO
}
Iadj
–
+
+
9
Comparator with Hysteresis
VS
R1
VO (REG) = 1.25V (1+R2/R1)+Iadj R2
VO
–
OP-07
+
LM308A
+
R2
VUL = {R1/(R1 + R2)} VO(max)
VLL = {R1/(R1 + R2)} VO(min)
(for additional circuits see AN115)
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
SYMBOL
SO-8
SO-14
SO16
(0.150”)
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
±0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
±0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
±0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
±0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
±0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
±0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
±0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
±0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
N
8
14
16
Rev. L 2/01
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
10
FN8222.1
December 20, 2006
X9C102, X9C103, X9C104, X9C503
Plastic Dual-In-Line Packages (PDIP)
E
D
A2
SEATING
PLANE
L
N
A
PIN #1
INDEX
E1
c
e
b
A1
NOTE 5
1
eA
eB
2
N/2
b2
MDP0031
PLASTIC DUAL-IN-LINE PACKAGE
SYMBOL
PDIP8
PDIP14
PDIP16
PDIP18
PDIP20
TOLERANCE
A
0.210
0.210
0.210
0.210
0.210
MAX
A1
0.015
0.015
0.015
0.015
0.015
MIN
A2
0.130
0.130
0.130
0.130
0.130
±0.005
b
0.018
0.018
0.018
0.018
0.018
±0.002
b2
0.060
0.060
0.060
0.060
0.060
+0.010/-0.015
c
0.010
0.010
0.010
0.010
0.010
+0.004/-0.002
D
0.375
0.750
0.750
0.890
1.020
±0.010
E
0.310
0.310
0.310
0.310
0.310
+0.015/-0.010
E1
0.250
0.250
0.250
0.250
0.250
±0.005
e
0.100
0.100
0.100
0.100
0.100
Basic
eA
0.300
0.300
0.300
0.300
0.300
Basic
eB
0.345
0.345
0.345
0.345
0.345
±0.025
L
0.125
0.125
0.125
0.125
0.125
±0.010
N
8
14
16
18
20
Reference
NOTES
1
2
Rev. B 2/99
NOTES:
1. Plastic or metal protrusions of 0.010” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions E and eA are measured with the leads constrained perpendicular to the seating plane.
4. Dimension eB is measured with the lead tips unconstrained.
5. 8 and 16 lead packages have half end-leads as shown.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
11
FN8222.1
December 20, 2006