S-5844A Series TEMPERATURE SWITCH IC (THERMOSTAT IC) www.sii-ic.com © SII Semiconductor Corporation, 2011-2014 Rev.2.6_01 The S-5844A Series is a temperature switch IC (thermostat IC) which detects the temperature with a temperature accuracy of ±2.5°C. The output inverts when temperature reaches the detection temperature. The S-5844A Series restores the output voltage when the temperature drops to the level of release temperature. The S-5844A Series operates at the lower power supply voltage of 1.65 V and its current consumption is 0.18 μA typ. due to CMOS configuration. A temperature sensor with the negative temperature coefficient, a reference voltage generation circuit and a comparator are integrated on one chip, and enclosed into the packages SOT-23-5 and SNT-4A, and the super-small package HSNT-4 (1010). Features • • • • • • • • Detection temperature: TDET = +50°C to +100°C, +5°C step, detection accuracy: ±2.5°C Low voltage operation: VDD = 1.65 V min. Low current consumption: IDD = 0.18 μA typ. (Ta = +25°C) Hysteresis temperature: selectable in 5°C, 10°C, 15°C or 20°C Selectable output logic in active "H" or active "L" Selectable output form in CMOS or Nch open-drain Operation temperature range: Ta = −40°C to +125°C Lead-free (Sn 100%), halogen-free Applications • • • • • Fan control Air conditioning system Mobile phone Game console Various electronic devices Packages • • • SOT-23-5 SNT-4A HSNT-4 (1010) 1 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Block Diagrams 1. CMOS output product VDD Temperature sensor + Logic circuit (selectable) − DET Reference voltage generation circuit TEST VSS Figure 1 2. Nch open-drain output product VDD Temperature sensor + Logic circuit (selectable) − Reference voltage generation circuit TEST VSS Figure 2 2 DET TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Product Name Structure Users are able to select the detection temperature, output form and logic, hysteresis temperature, and package for the S-5844A Series. 1. Product name S-5844A xx x x - xxxx U 3 Environmental code U: Lead-free (Sn 100%), halogen-free Package abbreviation and IC packing specifications*1 M5T1: SOT-23-5, Tape I4T1: SNT-4A, Tape A4T2: HSNT-4 (1010), Tape Hysteresis temperature*2 A: 5°C B: 10°C C: 15°C D: 20°C Output form and output logic*3 A: CMOS output, active "H" B: CMOS output, active "L" C: Nch open-drain output, active "H" D: Nch open-drain output, active "L" Detection temperature*4 50 to 95, A0 (When detection temperature is +80°C, it is expressed as 80. When detection temperature is +100°C, it is expressed as A0.) *1. *2. *3. *4. Refer to the tape drawing. The hysteresis temperature is selectable in 5°C, 10°C, 15°C, or 20°C. However, if the detection temperature is +50°C, select the hysteresis temperature in 5°C or 10°C. For the DET pin output, selectable the output logic active "H" or active "L". For the DET pin output, selectable the output form CMOS or Nch open-drain. Detection temperature (TDET) is settable in +50°C to +100°C, in +5°C step. 2. Packages Table 1 Package Name SOT-23-5 SNT-4A HSNT-4 (1010) Dimension MP005-A-P-SD PF004-A-P-SD PL004-A-P-SD Package Drawing Codes Tape MP005-A-C-SD PF004-A-C-SD PL004-A-C-SD Reel MP005-A-R-SD PF004-A-R-SD PL004-A-R-SD Land − PF004-A-L-SD PL004-A-L-SD 3 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 3. Product name list 3. 1 SOT-23-5 Table 2 Product Name Detection Temperature (TDET) DET Pin Output Form DET Pin Output Logic S-5844A50DB-M5T1U3 +50°C Nch open-drain Active "L" S-5844A55CB-M5T1U3 +55°C Nch open-drain Active "H" S-5844A55CC-M5T1U3 +55°C Nch open-drain Active "H" S-5844A55CD-M5T1U3 +55°C Nch open-drain Active "H" S-5844A55DB-M5T1U3 +55°C Nch open-drain Active "L" S-5844A60CB-M5T1U3 +60°C Nch open-drain Active "H" S-5844A60CC-M5T1U3 +60°C Nch open-drain Active "H" S-5844A60CD-M5T1U3 +60°C Nch open-drain Active "H" S-5844A60DB-M5T1U3 +60°C Nch open-drain Active "L" S-5844A65CB-M5T1U3 +65°C Nch open-drain Active "H" S-5844A65CC-M5T1U3 +65°C Nch open-drain Active "H" S-5844A65CD-M5T1U3 +65°C Nch open-drain Active "H" S-5844A65DA-M5T1U3 +65°C Nch open-drain Active "L" S-5844A65DB-M5T1U3 +65°C Nch open-drain Active "L" S-5844A70CB-M5T1U3 +70°C Nch open-drain Active "H" S-5844A70CC-M5T1U3 +70°C Nch open-drain Active "H" S-5844A70CD-M5T1U3 +70°C Nch open-drain Active "H" S-5844A70DB-M5T1U3 +70°C Nch open-drain Active "L" S-5844A75CB-M5T1U3 +75°C Nch open-drain Active "H" S-5844A75CC-M5T1U3 +75°C Nch open-drain Active "H" S-5844A75CD-M5T1U3 +75°C Nch open-drain Active "H" S-5844A75DB-M5T1U3 +75°C Nch open-drain Active "L" S-5844A80CB-M5T1U3 +80°C Nch open-drain Active "H" S-5844A80CC-M5T1U3 +80°C Nch open-drain Active "H" S-5844A80CD-M5T1U3 +80°C Nch open-drain Active "H" S-5844A80DB-M5T1U3 +80°C Nch open-drain Active "L" S-5844A85CB-M5T1U3 +85°C Nch open-drain Active "H" S-5844A85CC-M5T1U3 +85°C Nch open-drain Active "H" S-5844A85CD-M5T1U3 +85°C Nch open-drain Active "H" S-5844A85DB-M5T1U3 +85°C Nch open-drain Active "L" S-5844A90CB-M5T1U3 +90°C Nch open-drain Active "H" S-5844A90CC-M5T1U3 +90°C Nch open-drain Active "H" S-5844A90CD-M5T1U3 +90°C Nch open-drain Active "H" S-5844A90DB-M5T1U3 +90°C Nch open-drain Active "L" S-5844A95CB-M5T1U3 +95°C Nch open-drain Active "H" S-5844A95CC-M5T1U3 +95°C Nch open-drain Active "H" S-5844A95CD-M5T1U3 +95°C Nch open-drain Active "H" S-5844A95DB-M5T1U3 +95°C Nch open-drain Active "L" Remark Please contact our sales office for products with specifications other than the above. 4 Hysteresis Temperature (THYS) 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 5°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 3. 2 SNT-4A Table 3 Product Name Detection Temperature (TDET) DET Pin Output Form DET Pin Output Logic S-5844A50DB-I4T1U3 +50°C Nch open-drain Active "L" S-5844A55CB-I4T1U3 +55°C Nch open-drain Active "H" S-5844A55CC-I4T1U3 +55°C Nch open-drain Active "H" S-5844A55CD-I4T1U3 +55°C Nch open-drain Active "H" S-5844A55DB-I4T1U3 +55°C Nch open-drain Active "L" S-5844A60CB-I4T1U3 +60°C Nch open-drain Active "H" S-5844A60CC-I4T1U3 +60°C Nch open-drain Active "H" S-5844A60CD-I4T1U3 +60°C Nch open-drain Active "H" S-5844A60DB-I4T1U3 +60°C Nch open-drain Active "L" S-5844A65CB-I4T1U3 +65°C Nch open-drain Active "H" S-5844A65CC-I4T1U3 +65°C Nch open-drain Active "H" S-5844A65CD-I4T1U3 +65°C Nch open-drain Active "H" S-5844A65DB-I4T1U3 +65°C Nch open-drain Active "L" S-5844A70CB-I4T1U3 +70°C Nch open-drain Active "H" S-5844A70CC-I4T1U3 +70°C Nch open-drain Active "H" S-5844A70CD-I4T1U3 +70°C Nch open-drain Active "H" S-5844A70DB-I4T1U3 +70°C Nch open-drain Active "L" S-5844A75CB-I4T1U3 +75°C Nch open-drain Active "H" S-5844A75CC-I4T1U3 +75°C Nch open-drain Active "H" S-5844A75CD-I4T1U3 +75°C Nch open-drain Active "H" S-5844A75DB-I4T1U3 +75°C Nch open-drain Active "L" S-5844A80CB-I4T1U3 +80°C Nch open-drain Active "H" S-5844A80CC-I4T1U3 +80°C Nch open-drain Active "H" S-5844A80CD-I4T1U3 +80°C Nch open-drain Active "H" S-5844A80DB-I4T1U3 +80°C Nch open-drain Active "L" S-5844A85CB-I4T1U3 +85°C Nch open-drain Active "H" S-5844A85CC-I4T1U3 +85°C Nch open-drain Active "H" S-5844A85CD-I4T1U3 +85°C Nch open-drain Active "H" S-5844A85DB-I4T1U3 +85°C Nch open-drain Active "L" S-5844A90CB-I4T1U3 +90°C Nch open-drain Active "H" S-5844A90CC-I4T1U3 +90°C Nch open-drain Active "H" S-5844A90CD-I4T1U3 +90°C Nch open-drain Active "H" S-5844A90DB-I4T1U3 +90°C Nch open-drain Active "L" S-5844A95CB-I4T1U3 +95°C Nch open-drain Active "H" S-5844A95CC-I4T1U3 +95°C Nch open-drain Active "H" S-5844A95CD-I4T1U3 +95°C Nch open-drain Active "H" S-5844A95DB-I4T1U3 +95°C Nch open-drain Active "L" Remark Please contact our sales office for products with specifications other than the above. Hysteresis Temperature (THYS) 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 5 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series 3. 3 Rev.2.6_01 HSNT-4 (1010) Table 4 Product Name Detection Temperature (TDET) DET Pin Output Form DET Pin Output Logic S-5844A50DB-A4T2U3 +50°C Nch open-drain Active "L" S-5844A55CB-A4T2U3 +55°C Nch open-drain Active "H" S-5844A55CC-A4T2U3 +55°C Nch open-drain Active "H" S-5844A55CD-A4T2U3 +55°C Nch open-drain Active "H" S-5844A55DB-A4T2U3 +55°C Nch open-drain Active "L" S-5844A60CB-A4T2U3 +60°C Nch open-drain Active "H" S-5844A60CC-A4T2U3 +60°C Nch open-drain Active "H" S-5844A60CD-A4T2U3 +60°C Nch open-drain Active "H" S-5844A60DB-A4T2U3 +60°C Nch open-drain Active "L" S-5844A65CB-A4T2U3 +65°C Nch open-drain Active "H" S-5844A65CC-A4T2U3 +65°C Nch open-drain Active "H" S-5844A65CD-A4T2U3 +65°C Nch open-drain Active "H" S-5844A65DB-A4T2U3 +65°C Nch open-drain Active "L" S-5844A70CB-A4T2U3 +70°C Nch open-drain Active "H" S-5844A70CC-A4T2U3 +70°C Nch open-drain Active "H" S-5844A70CD-A4T2U3 +70°C Nch open-drain Active "H" S-5844A70DB-A4T2U3 +70°C Nch open-drain Active "L" S-5844A75CB-A4T2U3 +75°C Nch open-drain Active "H" S-5844A75CC-A4T2U3 +75°C Nch open-drain Active "H" S-5844A75CD-A4T2U3 +75°C Nch open-drain Active "H" S-5844A75DB-A4T2U3 +75°C Nch open-drain Active "L" S-5844A80CB-A4T2U3 +80°C Nch open-drain Active "H" S-5844A80CC-A4T2U3 +80°C Nch open-drain Active "H" S-5844A80CD-A4T2U3 +80°C Nch open-drain Active "H" S-5844A80DB-A4T2U3 +80°C Nch open-drain Active "L" S-5844A85CB-A4T2U3 +85°C Nch open-drain Active "H" S-5844A85CC-A4T2U3 +85°C Nch open-drain Active "H" S-5844A85CD-A4T2U3 +85°C Nch open-drain Active "H" S-5844A85DB-A4T2U3 +85°C Nch open-drain Active "L" S-5844A90CB-A4T2U3 +90°C Nch open-drain Active "H" S-5844A90CC-A4T2U3 +90°C Nch open-drain Active "H" S-5844A90CD-A4T2U3 +90°C Nch open-drain Active "H" S-5844A90DB-A4T2U3 +90°C Nch open-drain Active "L" S-5844A95CB-A4T2U3 +95°C Nch open-drain Active "H" S-5844A95CC-A4T2U3 +95°C Nch open-drain Active "H" S-5844A95CD-A4T2U3 +95°C Nch open-drain Active "H" S-5844A95DB-A4T2U3 +95°C Nch open-drain Active "L" Remark Please contact our sales office for products with specifications other than the above. 6 Hysteresis Temperature (THYS) 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C 10°C 15°C 20°C 10°C TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Pin Configurations 1. SOT-23-5 Top view 5 4 1 2 3 Figure 3 Table 5 Pin No. Symbol Description TEST*1 1 Test pin 2 VSS GND pin 3 DET Output pin NC*2 4 No connection 5 VDD Power supply pin *1. Connect the TEST pin to the VSS pin, or leave it open. *2. The NC pin is electrically open. The NC pin can be connected to the VDD pin or the VSS pin. 2. SNT-4A Top view 1 2 4 3 Table 6 Pin No. 1 2 3 4 Figure 4 *1. Symbol Description DET Output pin VSS GND pin TEST*1 Test pin VDD Power supply pin Connect the TEST pin to the VSS pin, or leave it open. 3. HSNT-4 (1010) Top view 1 2 4 3 Table 7 Pin No. 1 2 3 4 Bottom view 4 3 1 2 *1. Symbol Description DET Output pin VSS GND pin TEST*1 Test pin VDD Power supply pin Connect the TEST pin to the VSS pin, or leave it open. *1 *1. Connect the heat sink of backside at shadowed area to the board, and set electric potential open or GND. However, do not use it as the function of electrode. Figure 5 7 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Absolute Maximum Ratings Table 8 Item Symbol Power supply voltage (VSS = 0 V) VDD Pin voltage VTEST CMOS output product Output voltage VDET Nch open-drain output product Pch driving current IDETH Output pin current Nch driving current IDETL SOT-23-5 Power dissipation SNT-4A PD HSNT-4 (1010) Operation ambient temperature Topr Storage temperature Tstg *1. When mounted on board [Mounted board] (1) Board size: 114.3 mm × 76.2 mm × t1.6 mm (2) Board name: JEDEC STANDARD51-7 (Ta = +25°C unless otherwise specified) Absolute Maximum Rating Unit VSS + 6.0 VSS − 0.3 to VDD + 0.3 VSS − 0.3 to VDD + 0.3 VSS − 0.3 to VSS + 6.0 10 10 600*1 300*1 340*1 −40 to +125 −55 to +150 V V V V mA mA mW mW mW °C °C Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. 8 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 DC Electrical Characteristics 1. CMOS output product Table 9 Item Power supply voltage Detection temperature*1 Hysteresis temperature*2 Output voltage Symbol VDD +TD THYS VDETH VDETL Condition − − − IDETH = 0.5 mA IDETL = 0.5 mA (VDD = 3.0 V, Ta = +25°C unless otherwise specified) Test Min. Typ. Max. Unit Circuit 1.65 − 5.5 TDET − 2.5 TDET TDET + 2.5 − 5, 10, 15, 20 − VDD − 0.5 − − − − 0.5 Current consumption IDD − − 0.18 0.5 during operation *1. TDET: Set value of detection temperature *2. The hysteresis temperature is selectable in 5°C, 10°C, 15°C, or 20°C. However, if the detection temperature is +50°C, select the hysteresis temperature in 5°C or 10°C. V °C °C V V 1 1 1 2 3 μA 1 2. Nch open-drain output product Table 10 Item Symbol Condition (VDD = 3.0 V, Ta = +25°C unless otherwise specified) Test Min. Typ. Max. Unit Circuit Power supply voltage VDD − 1.65 − 5.5 Detection temperature*1 − TDET − 2.5 TDET TDET + 2.5 +TD Hysteresis temperature*2 − − 5, 10, 15, 20 − THYS Output voltage VDETL IDETL = 0.5 mA − − 0.5 Leakage current ILEAK VDET = 5.5 V − − 0.1 Current consumption IDD − − 0.18 0.5 during operation *1. TDET: Set value of detection temperature *2. The hysteresis temperature is selectable in 5°C, 10°C, 15°C, or 20°C. However, if the detection temperature is +50°C, select the hysteresis temperature in 5°C or 10°C. V °C °C V μA 1 1 1 3 4 μA 1 [Fahrenheit ⇔ Celsius conversion equation] °C = (°F − 32) × 5 / 9 °F = 32 + °C × 9 / 5 9 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Test Circuits A V VDD CIN VSS or Open TEST S-5844A Series DET VSS CL V *1. Resistor (R) is unnecessary for the CMOS output product. Figure 6 Test Circuit 1 V VDD CIN VSS or Open TEST S-5844A Series DET VSS V Figure 7 Test Circuit 2 V VDD CIN VSS or Open TEST S-5844A Series DET VSS V Figure 8 Test Circuit 3 V VDD CIN VSS or Open TEST S-5844A Series VSS Figure 9 Test Circuit 4 10 DET A V TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Operation The S-5844A Series is a temperature switch IC (thermostat IC) which detects temperature and sends a signal to an external device. The users can select various combinations of the parameters such as the detection temperature, the output form and logic, and hysteresis temperature. Following is about the operation when the DET pin output logic is active "H". After applying the power supply, the S-5844A Series starts to detect the temperature. If the temperature is lower than the detection temperature (+TD), the DET pin output keeps "L". After that, the temperature rises and exceeds the detection temperature, and the DET pin goes in "H". After the detection, the temperature drops and reaches the release temperature (+TD − THYS), the DET pin output returns to "L". Figure 10 is the timing chart. Hysteresis temperature (THYS) Detection temperature (TD) Release temperature (TD − THYS) Ambient temperature (Ta) H DET pin output L Figure 10 Operation when the DET Pin Output Logic is Active "H" 11 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Standard Circuit VDD TEST S-5844A Series DET VSS *1. Resistor (R) is unnecessary for the CMOS output product. Figure 11 Caution The above connection diagram will not guarantee successful operation. Perform thorough evaluation using actual application to set the constant. Precautions • • • • • • • • 12 If power impedance is high, the S-5844A Series may malfunction due to voltage drop caused by feed-through current. Set wire patterns carefully for lower power impedance. It is recommended to set a capacitor (CIN) of 0.1 μF or more between the VDD pin and VSS pin for stabilization. The S-5844A Series may malfunction if the power supply voltage changes suddenly. The S-5844A Series is more easily affected by disturbance or noise if the TEST pin is left open. It is recommended to set a capacitor (CL) of about 0.1 μF for the DET pin to prevent malfunction caused by the noise when the power supply is applied. The S-5844A Series may malfunction if the power supply voltage is lower than the minimum operation voltage. Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. SII Semiconductor Corporation claims no responsibility for any disputes arising out of or in connection with any infringement by products, including this IC, of patents owned by a third party. TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Characteristics (Typical Data) 1. Current consumption vs. Power supply voltage characteristics 0.5 IDD [μA] 0.4 +125°C 0.3 +25°C +95°C 0.2 0.1 −40°C 0 0 1.0 2.0 3.0 4.0 VDD [V] 5.0 6.0 2. DET pin current "H" vs. Power supply voltage characteristics (CMOS output product only) IDETH [mA] VDET = VDD − 0.25 V 4 +25°C 3 −40°C 2 +95°C 1 +125°C 0 0 1.0 2.0 3.0 4.0 VDD [V] 5.0 6.0 3. DET pin current "L" vs. Power supply voltage characteristics VDET = 0.25 V 10 +25°C IDETL [mA] 8 −40°C 6 4 +95°C 2 +125°C 0 0 1.0 2.0 3.0 4.0 VDD [V] 5.0 6.0 13 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 Marking Specifications 1. SOT-23-5 Top view 5 (1) to (3): (4): 4 Product code (refer to Product name vs. Product code) Lot number (1) (2) (3) (4) 1 2 3 Product name vs. Product code Product Name S-5844A50DB-M5T1U3 S-5844A55CB-M5T1U3 S-5844A55CC-M5T1U3 S-5844A55CD-M5T1U3 S-5844A55DB-M5T1U3 S-5844A60CB-M5T1U3 S-5844A60CC-M5T1U3 S-5844A60CD-M5T1U3 S-5844A60DB-M5T1U3 S-5844A65CB-M5T1U3 S-5844A65CC-M5T1U3 S-5844A65CD-M5T1U3 S-5844A65DA-M5T1U3 S-5844A65DB-M5T1U3 S-5844A70CB-M5T1U3 S-5844A70CC-M5T1U3 S-5844A70CD-M5T1U3 S-5844A70DB-M5T1U3 S-5844A75CB-M5T1U3 14 Product Code (1) (2) (3) 2 M 4 2 M F 2 O F 2 Q F 2 M X 2 M G 2 O G 2 Q G 2 M Y 2 M H 2 O H 2 Q H 2 K U 2 M Z 2 M I 2 O I 2 Q I 2 M 3 2 M A Product Name S-5844A75CC-M5T1U3 S-5844A75CD-M5T1U3 S-5844A75DB-M5T1U3 S-5844A80CB-M5T1U3 S-5844A80CC-M5T1U3 S-5844A80CD-M5T1U3 S-5844A80DB-M5T1U3 S-5844A85CB-M5T1U3 S-5844A85CC-M5T1U3 S-5844A85CD-M5T1U3 S-5844A85DB-M5T1U3 S-5844A90CB-M5T1U3 S-5844A90CC-M5T1U3 S-5844A90CD-M5T1U3 S-5844A90DB-M5T1U3 S-5844A95CB-M5T1U3 S-5844A95CC-M5T1U3 S-5844A95CD-M5T1U3 S-5844A95DB-M5T1U3 Product Code (1) (2) (3) 2 O A 2 Q A 2 M R 2 M B 2 O B 2 Q B 2 M S 2 M C 2 O C 2 Q C 2 M T 2 M D 2 O D 2 Q D 2 M U 2 M E 2 O E 2 Q E 2 M V TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 2. SNT-4A Top view (1) to (3): 1 Product code (refer to Product name vs. Product code) 4 (1) (2) (3) 2 3 Product name vs. Product code Product Name S-5844A50DB-I4T1U3 S-5844A55CB-I4T1U3 S-5844A55CC-I4T1U3 S-5844A55CD-I4T1U3 S-5844A55DB-I4T1U3 S-5844A60CB-I4T1U3 S-5844A60CC-I4T1U3 S-5844A60CD-I4T1U3 S-5844A60DB-I4T1U3 S-5844A65CB-I4T1U3 S-5844A65CC-I4T1U3 S-5844A65CD-I4T1U3 S-5844A65DB-I4T1U3 S-5844A70CB-I4T1U3 S-5844A70CC-I4T1U3 S-5844A70CD-I4T1U3 S-5844A70DB-I4T1U3 S-5844A75CB-I4T1U3 S-5844A75CC-I4T1U3 (1) 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Product Code (2) (3) M 4 M F O F Q F M X M G O G Q G M Y M H O H Q H M Z M I O I Q I M 3 M A O A Product Name S-5844A75CD-I4T1U3 S-5844A75DB-I4T1U3 S-5844A80CB-I4T1U3 S-5844A80CC-I4T1U3 S-5844A80CD-I4T1U3 S-5844A80DB-I4T1U3 S-5844A85CB-I4T1U3 S-5844A85CC-I4T1U3 S-5844A85CD-I4T1U3 S-5844A85DB-I4T1U3 S-5844A90CB-I4T1U3 S-5844A90CC-I4T1U3 S-5844A90CD-I4T1U3 S-5844A90DB-I4T1U3 S-5844A95CB-I4T1U3 S-5844A95CC-I4T1U3 S-5844A95CD-I4T1U3 S-5844A95DB-I4T1U3 (1) 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Product Code (2) (3) Q A M R M B O B Q B M S M C O C Q C M T M D O D Q D M U M E O E Q E M V 15 TEMPERATURE SWITCH IC (THERMOSTAT IC) S-5844A Series Rev.2.6_01 3. HSNT-4 (1010) Top view 4 (1) to (3): (4), (5): 3 Product code (refer to Product name vs. Product code) Lot number (1) (2) (3) (4) (5) 1 2 Product name vs. Product code Product Name S-5844A50DB-A4T2U3 S-5844A55CB-A4T2U3 S-5844A55CC-A4T2U3 S-5844A55CD-A4T2U3 S-5844A55DB-A4T2U3 S-5844A60CB-A4T2U3 S-5844A60CC-A4T2U3 S-5844A60CD-A4T2U3 S-5844A60DB-A4T2U3 S-5844A65CB-A4T2U3 S-5844A65CC-A4T2U3 S-5844A65CD-A4T2U3 S-5844A65DB-A4T2U3 S-5844A70CB-A4T2U3 S-5844A70CC-A4T2U3 S-5844A70CD-A4T2U3 S-5844A70DB-A4T2U3 S-5844A75CB-A4T2U3 S-5844A75CC-A4T2U3 16 (1) 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Product Code (2) (3) M 4 M F O F Q F M X M G O G Q G M Y M H O H Q H M Z M I O I Q I M 3 M A O A Product Name S-5844A75CD-A4T2U3 S-5844A75DB-A4T2U3 S-5844A80CB-A4T2U3 S-5844A80CC-A4T2U3 S-5844A80CD-A4T2U3 S-5844A80DB-A4T2U3 S-5844A85CB-A4T2U3 S-5844A85CC-A4T2U3 S-5844A85CD-A4T2U3 S-5844A85DB-A4T2U3 S-5844A90CB-A4T2U3 S-5844A90CC-A4T2U3 S-5844A90CD-A4T2U3 S-5844A90DB-A4T2U3 S-5844A95CB-A4T2U3 S-5844A95CC-A4T2U3 S-5844A95CD-A4T2U3 S-5844A95DB-A4T2U3 (1) 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Product Code (2) (3) Q A M R M B O B Q B M S M C O C Q C M T M D O D Q D M U M E O E Q E M V 2.9±0.2 1.9±0.2 4 5 1 2 +0.1 0.16 -0.06 3 0.95±0.1 0.4±0.1 No. MP005-A-P-SD-1.2 TITLE No. SOT235-A-PKG Dimensions MP005-A-P-SD-1.2 SCALE UNIT mm SII Semiconductor Corporation 4.0±0.1(10 pitches:40.0±0.2) +0.1 ø1.5 -0 2.0±0.05 +0.2 ø1.0 -0 0.25±0.1 4.0±0.1 1.4±0.2 3.2±0.2 3 2 1 4 5 Feed direction No. MP005-A-C-SD-2.1 TITLE SOT235-A-Carrier Tape No. MP005-A-C-SD-2.1 SCALE UNIT mm SII Semiconductor Corporation 12.5max. 9.0±0.3 Enlarged drawing in the central part ø13±0.2 (60°) (60°) No. MP005-A-R-SD-1.1 SOT235-A-Reel TITLE No. MP005-A-R-SD-1.1 SCALE QTY. UNIT 3,000 mm SII Semiconductor Corporation 1.2±0.04 3 4 +0.05 0.08 -0.02 2 1 0.65 0.48±0.02 0.2±0.05 No. PF004-A-P-SD-4.0 TITLE SNT-4A-A-PKG Dimensions PF004-A-P-SD-4.0 No. SCALE UNIT mm SII Semiconductor Corporation +0.1 ø1.5 -0 4.0±0.1 2.0±0.05 0.25±0.05 +0.1 5° 1.45±0.1 2 1 3 4 ø0.5 -0 4.0±0.1 0.65±0.05 Feed direction No. PF004-A-C-SD-1.0 TITLE SNT-4A-A-Carrier Tape No. PF004-A-C-SD-1.0 SCALE UNIT mm SII Semiconductor Corporation 12.5max. 9.0±0.3 Enlarged drawing in the central part ø13±0.2 (60°) (60°) No. PF004-A-R-SD-1.0 SNT-4A-A-Reel TITLE PF004-A-R-SD-1.0 No. SCALE UNIT QTY. 5,000 mm SII Semiconductor Corporation 0.52 1.16 2 0.52 0.35 1. 2. 0.3 1 (0.25 mm min. / 0.30 mm typ.) (1.10 mm ~ 1.20 mm) 0.03 mm 1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.). 2. Do not widen the land pattern to the center of the package (1.10 mm to 1.20 mm). Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package. 2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm or less from the land pattern surface. 3. Match the mask aperture size and aperture position with the land pattern. 4. Refer to "SNT Package User's Guide" for details. 1. 2. (0.25 mm min. / 0.30 mm typ.) (1.10 mm ~ 1.20 mm) No. PF004-A-L-SD-4.1 TITLE SNT-4A-A -Land Recommendation No. PF004-A-L-SD-4.1 SCALE UNIT mm SII Semiconductor Corporation 0.38±0.02 0.65 3 4 1 2 1.00±0.04 0.20±0.05 +0.05 0.08 -0.02 The heat sink of back side has different electric potential depending on the product. Confirm specifications of each product. Do not use it as the function of electrode. No. PL004-A-P-SD-1.0 TITLE HSNT-4-B-PKG Dimensions No. PL004-A-P-SD-1.0 SCALE UNIT mm SII Semiconductor Corporation 2.0±0.05 +0.1 ø1.5 -0 4.0±0.05 0.25±0.05 +0.1 1.12±0.05 5° 2 1 3 4 ø0.5 -0 2.0±0.05 0.5±0.05 Feed direction No. PL004-A-C-SD-1.0 TITLE HSNT-4-B-C a r r i e r Tape No. PL004-A-C-SD-1.0 SCALE UNIT mm SII Semiconductor Corporation +1.0 9.0 - 0.0 11.4±1.0 Enlarged drawing in the central part ø13±0.2 (60°) (60°) No. PL004-A-R-SD-1.0 HSNT-4-B-Reel TITLE PL004-A-R-SD-1.0 No. SCALE UNIT QTY. 10,000 mm SII Semiconductor Corporation Land Pattern 0.30min. 0.38~0.48 0.38~0.48 0.07 0.65±0.02 (1.02) Caution It is recommended to solder the heat sink to a board in order to ensure the heat radiation. PKG Metal Mask Pattern Aperture ratio Aperture ratio Caution Mask aperture ratio of the lead mounting part is 100%. Mask aperture ratio of the heat sink mounting part is 40%. Mask thickness: t0.10mm to 0.12 mm 100% 40% t0.10mm ~ 0.12 mm TITLE No. PL004-A-L-SD-2.0 HSNT-4-B -Land Recommendation PL004-A-L-SD-2.0 No. SCALE UNIT mm SII Semiconductor Corporation Disclaimers (Handling Precautions) 1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice. 2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of any specific mass-production design. SII Semiconductor Corporation is not responsible for damages caused by the reasons other than the products or infringement of third-party intellectual property rights and any other rights due to the use of the information described herein. 3. SII Semiconductor Corporation is not responsible for damages caused by the incorrect information described herein. 4. Take care to use the products described herein within their specified ranges. Pay special attention to the absolute maximum ratings, operation voltage range and electrical characteristics, etc. SII Semiconductor Corporation is not responsible for damages caused by failures and/or accidents, etc. that occur due to the use of products outside their specified ranges. 5. When using the products described herein, confirm their applications, and the laws and regulations of the region or country where they are used and verify suitability, safety and other factors for the intended use. 6. When exporting the products described herein, comply with the Foreign Exchange and Foreign Trade Act and all other export-related laws, and follow the required procedures. 7. The products described herein must not be used or provided (exported) for the purposes of the development of weapons of mass destruction or military use. SII Semiconductor Corporation is not responsible for any provision (export) to those whose purpose is to develop, manufacture, use or store nuclear, biological or chemical weapons, missiles, or other military use. 8. The products described herein are not designed to be used as part of any device or equipment that may affect the human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses. Do not use those products without the prior written permission of SII Semiconductor Corporation. Especially, the products described herein cannot be used for life support devices, devices implanted in the human body and devices that directly affect human life, etc. Prior consultation with our sales office is required when considering the above uses. SII Semiconductor Corporation is not responsible for damages caused by unauthorized or unspecified use of our products. 9. Semiconductor products may fail or malfunction with some probability. The user of these products should therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction. The entire system must be sufficiently evaluated and applied on customer's own responsibility. 10. The products described herein are not designed to be radiation-proof. The necessary radiation measures should be taken in the product design by the customer depending on the intended use. 11. The products described herein do not affect human health under normal use. However, they contain chemical substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Take care when handling these with the bare hands to prevent injuries, etc. 12. When disposing of the products described herein, comply with the laws and ordinances of the country or region where they are used. 13. The information described herein contains copyright information and know-how of SII Semiconductor Corporation. The information described herein does not convey any license under any intellectual property rights or any other rights belonging to SII Semiconductor Corporation or a third party. Reproduction or copying of the information described herein for the purpose of disclosing it to a third-party without the express permission of SII Semiconductor Corporation is strictly prohibited. 14. For more details on the information described herein, contact our sales office. 1.0-2016.01 www.sii-ic.com