Brochure

PSI²
Power Supply in Inductor
Efficiency
The high performance inductor minimizes losses at
full load, and the circuit topology maintains excellent
efficiency over the entire load range.
The next step in integration!
SPM1004
SUMIDA offers a new range of fully integrated power
modules which feature outstanding performance with
industry-leading power density. SUMIDA has
leveraged its extensive experience in inductor
technology to achieve the highest available efficiency
as well as optimized packaging for thermal
management.
In this product all components are integrated within
the inductor which provides significant benefits:
•The maximum amount of magnetic material is used,
rather than plastic fillers, allowing low loss and high
efficiency
•The coil can use thicker wire for lower resistive
losses and higher efficiency
•The magnetic material is thermally conductive,
avoiding hot spots
•The inductor provides electromagnetic shielding for
the switching components
•The integrated power module is fully tested and
dramatically simplifies the end product design
•The small size and very low profile (3 mm) package
reduces board space, allowing higher density designs
SPM1005
Thermal
The high conductivity of the magnetic material
maintains a uniform temperature across the module
and ensures that there are no "hot spots" (Figure 1).
The measured surface temperature is reduced by
11.5°C compared to a power module with an internal
inductor under identical conditions (Figure 2).
Figure 1 - SPM1005
Figure 2 - Comparison
Transient response
The circuit topology has been chosen to provide an
excellent response under transient load. The figure
below shows less than 20mV transient under a 3A
load step (SPM1004, Vin=12V and Vout=1V):
SPM1004
(Vin=12V and
Vout=1V)
•
•
SUMIDA Components & Modules GmbH | Dr. Hans-Vogt-Platz 1 | 94130 Obernzell
Phone: 08591/937-100 | [email protected] | www.sumida-eu.lcom
Updated February 4, 2016
PSI²
Power Supply in Inductor
EMI performance
Package size
The module is supplied in a Land Grid Array (LGA)
package with a very low profile (3mm), and the
footprint is only 9x15mm (SPM1004 and SPM1006) or
9x11mm (SPM1005). Very few external components
are required because all major components are
internal to the module, and because of the high
efficiency no forced airflow is needed up to 85°C
ambient. This makes it ideal for high density
applications.
All internal power traces are very short, minimizing
the loop area and reducing radiated EMI. The
inductor material is conductive and acts as a shield
over the internal components, further reducing EMI.
Evaluation boards
Design time
The module is fully tested during production and is
guaranteed to meet specifications. This simplifies the
end product design and PCB layout, and avoids
surprises during system testing. In contrast, a power
design based on separate components on the end
product PCB is higher risk and typically takes longer to
develop and debug.
SPM1004 and SPM1006 Evaluation Boards
Applications
•
•
•
•
•
Broadband and communications equipment
DSP and FPGA Point of Load applications
High density distributed power systems
Automated PCI / PCI express / PXI express
Automated test and medical equipment
Specification summary
Parameter
Input voltage
Output
current
Output
voltage
Efficiency
Conditions
SPM1004
SPM1005
SPM1006
9 - 15V
2.95-6V
4 - 28V
0-6A
0-6A
0-8A1
6A load
Fixed
0.8 - 5V
94.2% @5V
Adjustable
0.6 - 3.3V
94.2% @3.3V
Adjustable
0.6 - 5V
93% @5V
3A load
95.2% @5V
96.1% @3.3V
94.1% @5V
-40 to
+85°C
Features
Protection
Package LGA
Thermal
1
Ordering information (LGA package)
Power good output
Output
Voltage
Enable input
Soft start
SPM1004
SPM1005
SPM1006
Adjustable
(NA)
SPM1005-ZC
SPM1006-ZC
5.0V
SPM1004-5V0C
(NA)
SPM1006-5V0C
Auxiliary output
3.3V
SPM1004-3V3C
SPM1005-3V3C
SPM1006-3V3C
Overcurrent protection
2.5V
SPM1004-2V5C
SPM1005-2V5C
SPM1006-2V5C
Overvoltage protection
1.8V
SPM1004-1V8C
SPM1005-1V8C
SPM1006-1V8C
Undervoltage lockout
1.5V
SPM1004-1V5C
SPM1005-1V5C
SPM1006-1V5C
Thermal shutdown
1.2V
SPM1004-1V2C
SPM1005-1V2C
SPM1006-1V2C
3 mm
1.0V
SPM1004-1V0C
SPM1005-1V0C
SPM1006-1V0C
0.8V
SPM1004-0V8C
SPM1005-0V8C
SPM1006-0V8C
0.6V
(NA)
SPM1005-0V6C
SPM1006-0V6C
EVM
EVM1004
EVM1005
EVM1006
Height
Footprint
SPM1005 Evaluation Board
9 x 15 mm
9 x 11 mm
Pad size
0.63 mm
No airflow
-40 to +85°C
9 x 15 mm
Maximum 6A continuous at 85°C; refer to datasheet
To learn more about this product please email [email protected].
For more information on this and other Sumida products, visit www.sumida.com.
SUMIDA Technologies Inc. | 945 Princess Street | Kingston, Ontario | Canada
Email: [email protected]
Updated February 4, 2016