TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 5-V Input or 3.3-V Input, 3-A, Fully Integrated Converter Check for Samples: TPS51313 FEATURES APPLICATIONS • • • • • • • • • • 1 234 Input Voltage VIN Range : 3.1 V to 5.5 V Bias Voltage VCC Range: 3.1 V to 5.5 V Output Voltage Range: 0.6 V to 3.3 V 0.6-V, 1% Voltage Reference Accuracy Switching Frequency: 1 MHz No External Compensation is Required Fixed Voltage Servo Soft-Start Function Thermal Shutdown X DESCRIPTION FB 1 10 VCC 2 9 PGOOD VIN 3 8 NC PGND 4 7 SW PGND 5 6 SW Thermal Pad Discrete Graphics PCIe® PEX Rail Low-Voltage Point-of-Load (POL) Rails The TPS51313 is an easy-to-use, fully integrated, synchronous buck converter for low voltage point-ofload applications. It is designed to meet the NVIDIA™ OpenVreg Type 0 specifications, including the package and footprint requirement. It supports 3-A (maximum) of dc output current at output voltages from 0.6 V to 3.3 V. The D-CAP2™ mode adaptive, constant on-time control with 1-MHz switching frequency allows a small footprint when designed using all ceramic output capacitors and offers a low external component count. The device also features auto-skip function at light load condition, pre-biased start-up and internally fixed soft-start time. When the device is disabled, the output capacitor is discharged through internal resistor. The TPS51313 is available in a 3 mm x 3 mm, 10-pin DRC package (Green RoHS compliant and Pb free) and is specified between –10°C and 85°C. EN X SIMPLIFIED APPLICATION CFF R1 R2 TPS51313 FB EN VCC VIN 3.3 or 5V EN PGOOD VIN NC PGND SW PGND SW C IN PGOOD LOUT VOUT Thermal Pad COUT UDG-12083 1 2 3 4 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. D-CAP2 is a trademark of Texas Instruments. NVIDIA is a trademark of NVIDIA, Incorporated. PCIe is a registered trademark of PLX Technology, Inc. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012, Texas Instruments Incorporated TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) ORDERABLE DEVICE NUMBER TA PACKAGE –10°C to 85°C Plastic SON (DRC) (1) TPS51313DRCR TPS51313DRCT PINS 10 OUTPUT SUPPLY MINIMUM QUANTITY Tape and reel 3000 Mini reel 250 ECO PLAN Green (RoHS and no Pb/Br) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) VALUE Input voltage range (2) Output voltage range (2) MIN MAX VIN, VCC –0.3 6.0 SW –2.0 6.0 SW (transient 20nsec) -3.0 8.5 EN –0.3 6.0 FB –1 3.6 PGOOD –0.3 Junction temperature, TJ Storage temperature, Tstg (1) (2) –55 UNIT V 6.0 V 125 °C 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to the network ground terminal unless otherwise noted. THERMAL INFORMATION TPS51313 THERMAL METRIC (1) UNITS DRC (10-PIN) θJA Junction-to-ambient thermal resistance 42.4 θJCtop Junction-to-case (top) thermal resistance 53.9 θJB Junction-to-board thermal resistance 18.1 ψJT Junction-to-top characterization parameter 1.1 ψJB Junction-to-board characterization parameter 18.3 θJCbot Junction-to-case (bottom) thermal resistance 6.3 °C/W spacer - so note to thermal table has space between the note and ROC table title (1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. RECOMMENDED OPERATING CONDITIONS Input voltage range Output voltage range MIN MAX VIN, VCC –0.1 5.5 SW –0.1 5.5 EN –0.1 5.5 FB –0.1 3.5 PGOOD –0.1 5.5 V –10 85 °C Operating free-air temperature, TA 2 Submit Documentation Feedback UNIT V Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 ELECTRICAL CHARACTERISTICS Over operating free-air temperature range, VIN = 5 V, VCC = 5 V, VEN = 3.3 V (unless otherwise noted). PARAMETER TEST CONDITION MIN TYP MAX UNIT SUPPLY VOLTAGE VIN Supply voltage 3.1 5.5 V VCC Supply voltage 3.1 5.5 V SUPPLY CURRENT IIN Input voltage supply current EN = High 100 μA ISD Input voltage shutdown current EN = Low 12 μA IVCC(in) VCC supply current EN = High IVCC(sd) VCC shutdown current EN = Low, TA = 25°C μA 700 20 μA VFB REFERNCE VOLTAGE VFBREF Reference voltage VFBREFTOL Reference voltage tolerance IFB Feedback pin leakage current 0.6 TA = 25°C V –1% 1% –100 100 nA SMPS FREQUENCY fSW Switching frequency tOFF(min) Minimum off-time tDEAD Deadtime (1) EVM close loop measurement. VIN = 5 V, VOUT = 1.05 V, IOUT = 3 A 1 110 190 SW node high, VIN = 5 V 9 SW node low, VIN = 5 V 10 MHz 270 ns ns LOGIC THRESHOLD VLL EN low-level voltage VLH EN high-level voltage 0.8 ILLK EN input leakage current VIN = VCC = 3.3 V Soft-start time (1) VFB rising from 0 V to 0.6 V 1.5 –3 V V 1 3 μA SOFT START tSS 300 µs PGOOD COMPARATOR VPGTH PGOOD threshold tPGDLY PGOOD high delay time IPGLK PGOOD leakage current PGOOD out to higher w/r/t VFB 130% PGOOD out to lower w/r/t VFB 50% Delay for PGOOD in, after EN = Hi 1.3 –1 0 ms 1 μA CURRENT DETECTION IOCL Current limit threshold Valley current limit, VIN = VCC = 3.3 V, TA = 25°C 4.8 A PROTECTIONS VIN_UVLO VIN UVLO threshold voltage Wake-up 2.85 2.95 3.05 Shutdown 2.6 2.7 2.8 Wake-up 2.85 2.95 3.05 Shutdown 2.6 2.7 2.8 V VCC_UVLO VCC UVLO threshold voltage VOVP OVP threshold voltage OVP detect voltage, overdrive = 100 mV tOVP OVP delay time Overdrive = 100 mV VUVP UVP threshold voltage UVP detect voltage, overdrive = 100 mV tUVPDLY UVP delay time Overdrive = 100 mV 2.4 µs EN = Lo 260 Ω Shutdown temperature 145 130% 1.9 µs 50% SW PULL DOWN RSWPD Switch node pull down resistance THERMAL SHUTDOWN TSDN (1) Thermal shutdown threshold (1) Hysteresis 20 °C Specified by design. Not production tested. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 3 TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com DEVICE INFORMATION Functional Block Diagram TPS51313 VREF – 50% + PGOOD UV VBG Delay VREF VREF + 30% + OV UVP FB Σ + VSW OVP + ENOK EN 1.5 V/ 0.8 V Control Logic PWM + IGAIN + · · · · · On/Off Time Minimum On /Off SKIP Mode OCL/OVP/UVP Discharge + VCCOK VCC UVLO VCC 2.95 V/ 2.7 V + VINOK VIN UVLO 2.95 V/2.7 V VIN VBG OC + + tON One Shot XCON SW + ZC Discharge PGND UDG-12112 4 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 DRC PACKAGE 10 PINS (TOP VIEW) FB 1 10 VCC 2 9 PGOOD VIN 3 8 NC PGND 4 7 SW PGND 5 6 SW Thermal Pad EN . . PIN FUNCTIONS PIN NAME NO. I/O DESCRIPTION EN 10 I Enable function for the switched-mode power supply (SMPS) (3.3-V logic compatible) FB 1 I Voltage feedback. Also used for OVP, UVP and PGOOD determination. NC 8 I No connect. Make no external connection to this pin. I Device ground O Power good indicator. Requires external pull-up resistor. I Switching node output. Connect to external inductor. Also serve as current sensing negative input for over current protection purpose PGND PGOOD SW 4 5 9 6 7 VCC 2 VIN 3 Thermal Pad I Power supply for analog circuit. Main power conversion input and gate-drive voltage supply for output FETs. Connect to PGND. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 5 TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS 90 1.070 80 1.065 Output Voltage (V) Efficiency (%) 70 60 50 40 VOUT = 1.05 V VIN = 3.3 V fSW = 1 MHz 30 20 0.001 0.01 0.1 Output Current (A) 1 VIN = 3.3 V fSW = 1 MHz 1.060 1.055 1.050 1.045 1.040 0.0 3 0.5 1.0 1.5 2.0 Output Current (A) G000 Figure 1. Efficiency vs. Output Current 2.5 3.0 G001 Figure 2. DC Load Regulation 400 60 VIN =3.3 V ILOAD = 3 A VVOUT = 1.05 V fSW = 1 MHz 40 350 300 200 150 0 Phase (°) Gain (dB) 250 20 100 50 −20 Magnitude −40 100 1000 0 Phase 10000 100000 Frequency (Hz) 1000000 −50 10000000 G001 Figure 3. Bode Plot Figure 4. Fast 0-A to 3-A Transient Response 6 Figure 5. Slow 0-A to 3-A Transient Response Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 APPLICATION INFORMATION Functional Overview TPS51313 is a D-CAP2 mode adaptive on time converter with internal integrator. Monolithically integrate high side and low side FET supports output current to a maximum of 3-ADC. The converter automatically runs in discontinuous conduction mode to optimize light load efficiency. A switching frequency of 1-MHz enables optimization of the power train for the cost, size and efficiency performance of the design. PWM Operation The PWM operation is comprised of three separate loops, A, B and C as shown in Figure 6. L OUT VIN C OUT + – R LOAD Integrator VCS PWM Comparator Q S Q R Σ VC + + R1 + gM VFB R2 VREF + – tON OneShot + – B C RA R 11 CSN K1 + CA RB CSP R12 CB A UDG-12113 Figure 6. PWM Operation Internal Current Loop (A) Loop A is the internal current loop. The current information is sampled, divided and averaged at the SW node. The RC time constant and the gain of the current sense amplifier is chosen to cover the wide range of power stage design intended for this application. Internal Voltage Loop (B) Loop B is the internal voltage loop. The feedback voltage information is compared to the voltage reference at the input of the gM amplifier, the internal integrator is designed to provide a zero at the double pole location to boost phase margin at the desired crossover frequency. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 7 TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com Fast Feedforward Loop (C) Loop C is the additional loop that acts a direct fast feedforward loop to enhance the transient response. In steady state operation as shown in Figure 7, the on time is initiated by the interaction of the three loops mentioned above. When the (VC– VCS) is rising above threshold defined by (VFB – VREF), the PWM comparator issues the on time pulse after the propagation delay. The demand of on time occurs when the artificial current has reached the valley point. The load regulation is maintained by the integrator provided by the gM amplifier and internal integrator. In transient operation as shown in Figure 8, the benefit of this topology is becoming evident. In an all MLCC output configuration, especially when the output capacitance is low, when the load step is applied, the output voltage is immediately discharged to try to keep the load demand. The immediate reflection of the load demand is instantly reflected in the FB voltage. The (VFB – VREF) is thus served as a termination voltage level for the (VC – VCS), thus modulating the initiation of the on time. The transient response can be improved further by amplifying the difference between VFB and the VREF reference. VFB–VREF ILOAD VC – VCS IL tON PWM PWM delay ~100 ns PWM IL VFB –VREF VOUT VC – VCS UDG-12114 Figure 7. Steady-State Operation UDG-12115 Figure 8. Transient Operation PWM Frequency The TPS51313 operates at a switching frequency of 1 MHz. Light Load Power Saving Features The TPS51313 offers an automatic pulse-skipping feature to provide excellent efficiency over the entire load range. The converter senses the current when the low-side FET is on and prevents negative current flow by turning off the low side FET. This saves power by eliminating re-circulation of the inductor current. When the bottom FET is turned off, the converter enters discontinuous mode, and the switching frequency decreases, reducing switching loss. Power Sequences TPS51313 initiates the soft-start process when the EN, VIN and VCC pins are ready. The soft-start time 300 µs when the reference voltage is between 0 V and 0.6 VREF. The actual output ramp-up time is the same as that of the VREF start-up time, which is 300 µs. Power Good Signal The TPS51313 has one open-drain power good (PGOOD) pin. During initial startup, there is a 1.3-ms power good high propagation delay after EN goes high. The PGOOD de-asserts when the EN is pulled low or an undervoltage condition on VCC or VIN or any other faults (such as VOUT, UVP, OCP, OVP) that require latch off action is detected. Protection Features The TPS51313 offers many features to protect the converter power chain as well as the system electronics. 8 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 Input Undervoltage Protection on VCC and VIN (UVLO) The TPS51313 continuously monitor the voltage on the VCC and VIN to ensure the voltage level is high enough to bias the converter properly and to provide sufficient gate drive potential to maintain high efficiency for the converter. The converter starts with VCC and VIN approximately 2.95 V and has a nominal of 250 mV of hysteresis, assuming EN is above the logic threshold level. If the UVLO level is reached for either VCC or VIN, the converter transitions the SW node into a tri-state and remains off until the device is reset by both VCC and VIN reaches 2.95 V (nominal). The PGOOD is deasserted when UVLO is detected and remains low until the device is reset. The device resumes operation when VIN recoveres to 2.95 V (nominal). Output Overvoltage Protection (OVP) The TPS51313 has OVP protection circuit. An OVP event is detected when the FB voltage is approximately 130% x 0.6VREF. In this case, the converter de-asserts the PGOOD signal and performs the overvoltage protection function. The converter latches off both high-side and low-side FET (after a typical delay of 1.9 µs) and remains in this state until the device is reset by EN, or VCC or VIN. Output Undervoltage Protection (UVP) Output undervoltage protection works in conjunction wit the current protection described in the Overcurrent and Current Limit Protection section. If the FB voltage drops below 50% x 0.6 VREF, after a delay of 2.4 µs, the converter latches off. Undervoltage protection can be reset by EN, VCC or VIN. Overcurrent and Current Limit Protection The TPS51313 provides an overcurrent protection function. The minimum OCP level is 4.8-A DC. When the current limit is exceeded for consecutive 9 cycles, the converter latches off and remains latched off until it is reset by EN, VCC or VIN. The TPS51313 also provides current limit protection function. If the sense current is above the OCL setting, the converter delays the next on pulse until the current level drops below the OCL limit. Current limiting occurs on a pulse-by-pulse basis. During a fast or very fast overcurrent event, the output voltage tends to droop until the UVP limit is reached. Then the converter de-asserts the PGOOD signal, and latches off after a delay between 1 µs and 2 µs . The converter remains in this state until the device is reset by EN, VCC or VIN. Thermal Protection The TPS51313 has an internal temperature sensor. When the die temperature reaches a nominal of 145°C, the device shuts down until the temperature cools by approximately 20°C. Then the converter restarts. The thermal shutdown is an non-latched behavior. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 9 TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com REFERENCE DESIGN Application Schematic This section describes a simplified design procedure for a discrete graphics processor PEX rail application using the TPS51313 converter. Figure 9 shows the application schematic.. CFF R1 R2 TPS51313 FB EN VCC VIN 3.3 or 5V EN PGOOD VIN NC PGND SW PGND SW C IN PGOOD LOUT VOUT COUT Thermal Pad UDG-12083 Figure 9. Reference Design Schematic Table 1. Reference Design List of Materials FUNCTION MANUFACTURER PART NUMBER Output Inductor Vishay IHLP-1212AB-11 Ceramic Output Capacitors Panasonic ECJ2FB0J226M Murata GRM21BR60J226ME39L Design Procedure Step One. Determine the specifications. . The PEX rail requirement provides the following key paramaters. • VOUT = 1.05 V • ICC(max) = 3 A • ΔI = 2A (transient load step and release) • di/dt = 2.5A/µs Step Two. Determine the system parameters. The input voltage range and operating frequency are of primary interest. For example, • VIN = VCC = 3.3 V • fSW = 1 MHz. • Maximum height of power chain components = 1.2 mm 10 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 TPS51313 www.ti.com SLUSB31 – SEPTEMBER 2012 Step Three. Set the output voltage. Use Equation 1 to determine the output voltage. VOUT = VREF ´ (R1 + R2 ) R2 (1) The output voltage is determined by 0.6-V votlage reference and the resistor dividers (R1 and R2). The output voltage is regulated to the FB pin. For this VOUT = 1.05 V, reference design, select R1 = 30 kΩ and R2 = 40 kΩ. (see Figure 9) To improve signal-to-noise performance of the converter, add a small feedforward capacitor (typically approximately 27 pF or less) in parallel with the upper resistor (R1). Step Four. Determine inductor value and choose inductor. Smaller inductance yields better transient performance but the consequence is higher ripple and lower efficiency. Higher values have the opposite characteristics. It is common practice to limit the ripple current to 25% to 50% of the maximum current. In this case, use 40%: IP-P = 3 A ´ 0.4 = 1.2 A where • • • L= fSW = 1 MHz VIN = 3.3 V VOUT = 1.05 V (2) ö V ´ dT æ (VIN - VOUT ) ö æ VOUT =ç ÷´ç ÷ = 0.596 mH ç ÷ ç (fSW ´ VIN ) ÷ IP-P IP-P è ø è ø (3) For this application, a 0.56-µH, 18.7-mΩ inductor from Vishay with part number IHLP-1212AB-11 is chosen. Maximum height for this inductor is 1.2 mm. Step Five. Determine the output capacitance. To determine COUT based on transient and stability requirement, first calculate the minimum output capacitance for a given transient. Equation 4 and Equation 5 calculate the minimum output capacitance for meeting the transient requirement, which is 33.8-µF assuming a ±3% voltage allowance for load step and release. æV ö ´t L ´ DILOAD(max )2 ´ ç VOUT SW + tMIN(off ) ÷ ç VIN(min ) ÷ è ø COUT(min_ under ) = ææ V ö ö IN(min ) - VVOUT ÷ ÷ ´ tSW - t 2 ´ DVLOAD(insert ) ´ ç ç MIN(off ) ÷ ´ VVOUT çç ÷ VIN(min ) ø èè ø COUT(min_ over ) = ( (4) 2 LOUT ´ DILOAD(max ) ) 2 ´ DVLOAD(release ) ´ VVOUT (5) This design uses 3 22-µF capacitors with consideration of the MLCC derating effect (60% derating for both AC and DC effect). Step Six. Establishing the internal compensation loop. The TPS51313 is designed with an internal compensation loop. The internal integrator zero location is approximately 60 kHz. When the power stage double pole frequency contributed by the LOUT and COUT is less than or equal to that of the zero frequency location, the converter is stable with sufficient margin. Step Seven. Select decoupling and peripheral components. For TPS51313 peripheral capacitors use the following minimum value of ceramic capacitance, X5R or better temperature coefficient is recommended. Tighter tolerances and higher voltage ratings are always appropriate. Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 11 TPS51313 SLUSB31 – SEPTEMBER 2012 www.ti.com VCC and VIN decoupling ≥ 2 × 10 µF, 6.3 V Pull up resistor on PGOOD = 100 kΩ Step Eight. (Optional) Snubber design for optimizing maximum switch node ringing. For TPS51313 layout design, if the maximum switch node voltage is above 8.5 V for 20 ns, snubber circuit is recommended to limit the maximum voltage to be within the absolute maximum voltage rating (see Absolute maximum rating table on page 2). A series combination of R and C (where the value of R is approximately 2.2 Ω, and the value of C is approximately 470 pF) from SW node to PGND can be added to achieve effective snubbing for SW node. Layout Considerations Good layout is essential for stable power supply operation. Follow these guidelines for an efficient PCB layout. • Widen the PGND connection area as much as possible. • Place VIN, VCC decoupling capacitors as close to the device as possible. • Use wide traces for the VIN, SW and PGND pins. These nodes carry high current and also serve as heat sinks. • Place FB and voltage setting dividers as close to the device as possible. 12 Submit Documentation Feedback Copyright © 2012, Texas Instruments Incorporated Product Folder Links :TPS51313 PACKAGE OPTION ADDENDUM www.ti.com 24-Jan-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) TPS51313DRCR ACTIVE SON DRC 10 3000 Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR & no Sb/Br) -10 to 85 S51313 TPS51313DRCT ACTIVE SON DRC 10 250 Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR & no Sb/Br) -10 to 85 S51313 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Only one of markings shown within the brackets will appear on the physical device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS51313DRCR SON DRC 10 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS51313DRCT SON DRC 10 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Jan-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS51313DRCR SON DRC 10 3000 367.0 367.0 35.0 TPS51313DRCT SON DRC 10 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated