INTERSIL X96012V14IZ

X96012
®
Data Sheet
February 20, 2008
Universal Sensor Conditioner with Dual
Look-up Table Memory and DACs
The X96012 is a highly integrated bias controller, which
incorporates two digitally controlled Programmable Current
Generators, temperature compensation with dedicated look-up
tables, and supplementary EEPROM array. All functions of the
device are controlled via a 2-wire digital serial interface.
FN8216.3
Features
• Two Programmable Current Generators
- ±3.2mA Max
- 8-bit (256 Step) Resolution
- Internally Programmable Full Scale Current Outputs
- External Resistor Pin to Set Full Scale Current Outputs
• Integrated 8-bit A/D Converter
Two temperature compensated Programmable Current
Generators, vary the output current with temperature
according to the contents of the associated nonvolatile
look-up table. The look-up table may be programmed with
arbitrary data by the user, via the 2-wire serial port, and
either an internal or external temperature sensor may be
used to control the output current response.
• Internal Voltage Reference with Output/Input
• Temperature Compensation
- Internal or External Sensor
- -40°C to +100°C Range
- +2.2°C/step Resolution
- EEPROM Look-up Tables
The integrated General Purpose EEPROM is included for
product data storage.
• Hot Pluggable
Ordering Information
• 2176-bit EEPROM
- 17 Pages
- 16 Bytes per Page
PART
NUMBER
X96012V14I
PART
MARKING
X9601 2VI
X96012V14IZ* X9601 2VIZ
(Note)
TEMP
RANGE (°C)
PACKAGE
PKG.
DWG. #
-40 to +100 14 Ld TSSOP M14.173
-40 to +100 14 Ld TSSOP M14.173
(Pb-free)
*Add “-T1” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the
Pb-free requirements of IPC/JEDEC J STD-020.
• Write Protection Circuitry
- Intersil BlockLock™
- Logic Controlled Protection
- 2-wire Bus with 3 Slave Address Bits
• 3V to 5.5V, Single Supply Operation
• Package
- 14 Ld TSSOP
• Pb-Free Available (RoHS Compliant)
Applications
• PIN Diode Bias Control
• RF PA Bias Control
Pinout
• Temperature Compensated Process Control
X96012
(14 LD TSSOP)
TOP VIEW
• Laser Diode Bias Control
• Fan Control
A0
1
14 I 2
A1
2
13 VREF
A2
3
12 VSENSE
VCC
4
11 VSS
WP
5
10 R2
SCL
6
9
R1
SDA
7
8
I1
• Motor Control
• Sensor Signal Conditioning
• Data Aquisition Applications
• Gain vs Temperature Control
• High Power Audio
• Open Loop Temperature Compensation
• Closed Loop Current, Voltage, Pressure, Temperature,
Speed, Position Programmable Voltage Sources,
Electronic Loads, Output Amplifiers or Function Generator
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005, 2007, 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X96012
Block Diagram
VOLTAGE
REFERENCE
VREF
R2
MUX
LOOK-UP
TABLE 2
MUX
DAC 2
I2
MUX
LOOK-UP
TABLE 1
MUX
DAC 1
I1
ADC
VSENSE
TEMPERATURE
SENSOR
SDA
SCL
WP
A2, A1, A0
2-WIRE
INTERFACE
CONTROL
AND STATUS
R1
GENERAL
PURPOSE
MEMORY
Pin Descriptions
PIN
NUMBER
PIN
NAME
1
A0
Device Address Select Pin 0. This pin determines the LSB of the device address required to communicate using the
2-wire interface. The A0 pin has an on-chip pull-down resistor.
2
A1
Device Address Select Pin 1. This pin determines the intermediate bit of the device address required to communicate
using the 2-wire interface. The A1 pin has an on-chip pull-down resistor.
3
A2
Device Address Select Pin 2. This pin determines the MSB of the device address required to communicate using the
2-wire interface. The A2 pin has an on-chip pull-down resistor.
PIN DESCRIPTION
4
VCC
Supply Voltage.
5
WP
Write Protect Control Pin. This pin is a CMOS compatible input. When LOW, Write Protection is enabled preventing
any “Write” operation. When HIGH, various areas of the memory can be protected using the Block Lock bits BL1 and
BL0. The WP pin has an on-chip pull-down resistor, which enables the Write Protection when this pin is left floating.
6
SCL
Serial Clock. This is a TTL compatible input pin. This input is the 2-wire interface clock controlling data input and output
at the SDA pin.
7
SDA
Serial Data. This pin is the 2-wire interface data into or out of the device. It is TTL compatible when used as an input,
and it is Open Drain when used as an output. This pin requires an external pull-up resistor.
8
I1
Current Generator 1 Output. This pin sinks or sources current. The magnitude and direction of the current is fully
programmable and adaptive. The resolution is 8 bits.
9
R1
Current Programming Resistor 1. A resistor between this pin and VSS can set the maximum output current available
at pin I1. If no resistor is used, the maximum current must be selected using control register bits.
10
R2
Current Programming Resistor 2. A resistor between this pin and VSS can set the maximum output current available
at pin I2. If no resistor is used, the maximum current must be selected using control register bits.
Ground.
11
VSS
12
VSENSE
13
VREF
14
I2
Sensor Voltage Input. This voltage input may be used to drive the input of the on-chip A/D converter.
Reference Voltage Input or Output. This pin can be configured as either an Input or an Output. As an Input, the
voltage at this pin is provided by an external source. As an Output, the voltage at this pin is a buffered output voltage
of the on-chip bandgap reference circuit. In both cases, the voltage at this pin is the reference for the A/D converter and
the two D/A converters.
Current Generator 2 Output. This pin sinks or sources current. The magnitude and direction of the current is fully
programmable and adaptive. The resolution is 8 bits.
2
FN8216.3
February 20, 2008
X96012
Absolute Maximum Ratings
Thermal Information
All Voltages are Referred to VSS
Temperature Under bias . . . . . . . . . . . . . . . . . . . . .-65°C to +100°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on Every Pin Except VCC. . . . . . . . . . . . . . . . . -1.0V to +7V
Voltage on VCC Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 5.5V
DC Output Current at Pin SDA . . . . . . . . . . . . . . . . . . 0mA to 5 mA
DC Output Current at Pins R1, R2, VREF and VSENSE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.50mA to 1mA
DC Output Current at Pins I1 and I2 . . . . . . . . . . -3.5mA to +3.5mA
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
14 Lead TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Temperature While Writing to Memory . . . . . . . . . . . . 0°C to +70°C
Voltage on VCC Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 5.5V
Voltage on any other Pin . . . . . . . . . . . . . . . . . . . . . . . . . VCC ± 0.3V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty
NOTE:
1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
.
Electrical Specifications
SYMBOL
Conditions are as follows, unless otherwise specified. All typical values are for TA = +25°C and 5V at pin VCC.
Maximum and minimum specifications are over the recommended operating conditions. All voltages are
referred to the voltage at pin VSS. All bits in control registers are “0”. 255Ω, 0.1%, resistor connected between
R1 and VSS, and another between R2 and VSS. 400kHz TTL input at SCL. SDA pulled to VCC through an
external 2kΩ resistor. 2-wire interface in “standby” (see Notes 9 and 10 on page 5). WP, A0, A1, and A2 floating.
VREF pin unloaded.
PARAMETER
TEST CONDITIONS
MIN
(Note 3)
TYP
MAX
(Note 3)
UNIT
Iccstby
Stand-by Current into VCC Pin
R1 and R2 floating, VREF unloaded.
2
mA
Iccfull
Full Operation Current into VCC
Pin
2-wire interface reading from
memory, I1 and I2 both connected to VSS,
DAC input bytes: FFh, VREF unloaded.
15
mA
Iccwrite
Nonvolatile Write Current into
VCC Pin
Average from START condition until tWP
after the STOP condition
WP: VCC, R1 and R2 Floating, VREF
unloaded.
IPLDN
On-chip Pull-down Current at WP, V(WP), V(A0), V(A1), and V(A2) from 0V
A0, A1, and A2
to VCC
VILTTL
SCL and SDA, Input Low Voltage
VIHTTL
SCL and SDA, Input High Voltage
IINTTL
SCL and SDA Input Current
Pin voltage between 0 and VCC, and SDA
as an input.
-1
10
µA
VOLSDA
SDA Output Low Voltage
I(SDA) = 2mA
0
0.4
V
IOHSDA
SDA Output High Current
V(SDA) = VCC
0
100
µA
VILCMOS
WP, A0, A1, and A2 Input Low
Voltage
0
0.2 x VCC
V
VIHCMOS
WP, A0, A1, and A2 Input High
Voltage
0.8 x VCC
VCC
V
VRefout
Output Voltage at VREF at +25°C
-20µA ≤ I(VREF) ≤ 20µA
1.215
V
RVREF
VREF Pin Input Resistance
VRM bit = “1”, +25°C
20
40
kΩ
TCOref
Temperature Coefficient of VREF
Output Voltage
Notes 2 and 8
-100
+100
ppm/°C
VRef Range
Voltage Range when VREF is an
Input
Note 6
1
1.3
V
TSenseRange
Temperature Sensor Range
Note 2
-40
100
°C
TSenseAccuracy
Temperature Sensor Accuracy
3
4
0
1
mA
20
µA
0.8
V
2.0
1.205
V
1.21
+/-2
°C
FN8216.3
February 20, 2008
X96012
Electrical Specifications
SYMBOL
Conditions are as follows, unless otherwise specified. All typical values are for TA = +25°C and 5V at pin VCC.
Maximum and minimum specifications are over the recommended operating conditions. All voltages are
referred to the voltage at pin VSS. All bits in control registers are “0”. 255Ω, 0.1%, resistor connected between
R1 and VSS, and another between R2 and VSS. 400kHz TTL input at SCL. SDA pulled to VCC through an
external 2kΩ resistor. 2-wire interface in “standby” (see Notes 9 and 10 on page 5). WP, A0, A1, and A2 floating.
VREF pin unloaded. (Continued)
PARAMETER
TEST CONDITIONS
MIN
(Note 3)
MAX
(Note 3)
UNIT
0
3200
µA
TYP
IR
Current from pin R1 or R2 to VSS
VPOR
Power-on Reset Threshold
Voltage
1.5
2.8
V
VCCRamp
VCC Ramp Rate
0.2
50
mV/µs
VADCOK
ADC Enable Minimum Voltage
2.6
2.8
V
Figure 11
NOTES:
2. These parameters are periodically sampled and not 100% tested.
3. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
4. The device goes into Standby: 200ns after any STOP, except those that initiate a nonvolatile write cycle. It goes into Standby tWC after a STOP
that initiates a nonvolatile write cycle. It also goes into Standby 9 clock cycles after any START that is not followed by the correct Slave Address
Byte.
5. tWC is the time from a valid STOP condition at the end of a write sequence to the end of the self-timed internal nonvolatile write cycle. It is the
minimum cycle time to be allowed for any nonvolatile write by the user, unless Acknowledge Polling is used.
6. For this range of V(VREF) the full scale sink mode current at I1 and I2 follows V(VREF) with a linearity error smaller than 1%.
7. These parameters are periodically sampled and not 100% tested.
8. TCOref = [Max V(VREF) - Min V(VREF)] x 106/(1.21V x +140°C).
D/A Converter Characteristics (See “Electrical Specifications” table starting on page 3 for standard conditions).
MIN
(Note 3)
TYP
MAX
(Note 3)
UNIT
I1 or I2 Full Scale Current, with External Resistor (Notes 9, 12)
Setting
(Notes 2, 9, 13)
1.56
1.58
1.6
mA
3.2
mA
IFS01
I1 or I2 Full Scale Current, with Internal Low
Current Setting Option
0.3
0.4
0.5
mA
IFS10
I1 or I2 Full Scale Current, with Internal Middle
Current Setting Option
0.64
0.85
1.06
mA
IFS11
I1 or I2 Full Scale Current, with Internal High
Current Setting Option
1
1.3
1.6
mA
OffsetDAC
I1 or I2 D/A Converter Offset Error
1
1
LSB
FSErrorDAC
I1 or I2 D/A Converter Full Scale Error
-2
2
LSB
DNLDAC
I1 or I2 D/A Converter Differential Nonlinearity
-0.5
0.5
LSB
INLDAC
I1 or I2 D/A Converter Integral Nonlinearity with
Respect to a Straight Line Through 0 and the Full
Scale Value
-1
1
LSB
VISink
I1 or I2 Sink Voltage Compliance
(Note 12)
1.2
VCC
V
(Notes 2, 13)
2.5
VCC
V
(Note 12)
0
VCC - 1.2
V
(Notes 2, 13)
0
VCC - 2.5
V
SYMBOL
IFS00
VISource
PARAMETER
I1 or I2 Source Voltage Compliance
4
TEST CONDITIONS
DAC input Byte = FFh,
Source or sink mode, V(I1) and V(I2)
are VCC - 1.2V in source mode and
1.2V in sink mode.
(Notes 10, 11)
FN8216.3
February 20, 2008
X96012
D/A Converter Characteristics (See “Electrical Specifications” table starting on page 3 for standard conditions). (Continued)
SYMBOL
PARAMETER
MIN
(Note 3)
TEST CONDITIONS
IOVER
I1 or I2 Overshoot on D/A Converter Data Byte
Transition
IUNDER
I1 or I2 Undershoot on D/A Converter Data Byte
Transition
trDAC
I1 or I2 Rise Time on D/A Converter Data Byte
Transition; 10% to 90%
TCOI1I2
Temperature Coefficient of Output Current I1 or
I2 when Using Internal Resistor Setting
TYP
DAC input byte changing from 00h to
FFh and vice versa, V(I1) and V(I2)
are VCC - 1.2V in source mode and
1.2V in sink mode. (Note 2)
5
MAX
(Note 3)
UNIT
0
µA
0
µA
30
µs
±200
Bits I1FSO[1:0] ¦ 002 or
Bits I2FSO[1:0] ¦ 002,
VRMbit = “1”
See Figure 8
ppm/°C
NOTES:
9. DAC input Byte = FFh, Source or sink mode.
2 V(VRef)
divided by the resistance between R1 or R2 to VSS.
x
255
3
11. OffsetDAC: The Offset of a DAC is defined as the deviation between the measured and ideal output, when the DAC input is 01h. It is expressed in
LSB. FSErrorDAC: The Full Scale Error of a DAC is defined as the deviation between the measured and ideal output, when the input is FFh. It is
expressed in LSB. The OffsetDAC is subtracted from the measured value before calculating FSErrorDAC.DNLDAC: The Differential Non-Linearity of
a DAC is defined as the deviation between the measured and ideal incremental change in the output of the DAC, when the input changes by one
code step. It is expressed in LSB. The measured values are adjusted for Offset and Full Scale Error before calculating DNLDAC. INLDAC: The
Integral Non-Linearity of a DAC is defined as the deviation between the measured and ideal transfer curves, after adjusting the measured transfer
curve for Offset and Full Scale Error. It is expressed in LSB.
10. LSB is defined as
[
]
12. V(I1) and V(I2) are VCC - 1.2V in source mode and 1.2V in sink mode. In this range the current at I1 or I2 varies < 1%.
13. The maximum current, sink or source, can be set with an external resistor to 3.2 mA with a minimum VCC = 4.5V. The compliance
voltage changes to 2.5V from the sourcing rail, and the current variation is < 1%.
.
A/D Converter Characteristics (See “Electrical Specifications” table starting on page 3 for standard conditions).
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
(Note 3)
TYP
MAX
(Note 3)
UNIT
9
ms
ADCTIME
A/D Converter Conversion Time
Proportional to A/D converter input voltage.
This value is maximum at full scale input of
A/D converter. ADCfiltOff = “1”
RINADC
VSense Pin Input Resistance
VSense as an input, ADCIN bit = “1”
100
CINADC
VSense Pin Input Capacitance
VSense as an input, ADCIN bit = “1”,
Frequency = 1 MHz. (Note 2)
1
7
pF
VINADC
VSense Input Signal Range
This is the A/D Converter Dynamic
Range. ADCIN bit = “1”
0
V(VRef)
V
kΩ
THE ADC IS MONOTONIC
OffsetADC
A/D Converter Offset Error
FSErrorADC
A/D Converter Full Scale Error
DNLADC
A/D Converter Differential
Nonlinearity
INLADC
A/D Converter Integral Nonlinearity
TempStepADC
Temperature Step Causing One
Step Increment of ADC Output
Out25ADC
ADC Output at +25°C
5
(Notes 2, 14)
(Note 2)
0.52
±1
LSB
±1
LSB
±0.5
LSB
±1
LSB
0.55
0.58
°C
011101012
FN8216.3
February 20, 2008
X96012
A/D Converter Characteristics (See “Electrical Specifications” table starting on page 3 for standard conditions).
SYMBOL
PARAMETER
MIN
(Note 3)
TEST CONDITIONS
TYP
MAX
(Note 3)
UNIT
NOTES:
14. LSB” is defined as V(VRef)/255, “Full-Scale” is defined as V(VRef).
[
]
0.5 x V(VRef)
above zero. Offset error is the amount of
15. OffsetADC: For an ideal converter, the first transition of its transfer curve occurs at
255
deviation between the measured first transition point and the ideal point. FSErrorADC: For an ideal converter, the last transition of its transfer
254.5 x V(VRef)
curve occurs at
. Full-Scale Error is the amount of deviation between the measured last transition point and the ideal point,
255
after subtracting the Offset from the measured curve. DNLADC: DNL is defined as the difference between the ideal and the measured code
transitions for successive A/D code outputs expressed in LSBs. The measured transfer curve is adjusted for Offset and Full-scale errors before
calculating DNL. INLADC: The deviation of the measured transfer function of an A/D converter from the ideal transfer function. The INL error is
also defined as the sum of the DNL errors starting from code 00h to the code where the INL measurement is desired. The measured transfer
curve is adjusted for Offset and Full scale errors before calculating INL.
[
]
2-Wire Interface AC Characteristics
SYMBOL
PARAMETER
MIN
(Note 3)
TEST CONDITIONS
1
(Note 18)
TYP
MAX
(Note 3)
UNITS
400
kHz
50
ns
900
ns
fSCL
SCL Clock Frequency
See “2-Wire Interface Test
Conditions” on page 6
tIN (Note 2)
Pulse width Suppression Time at Inputs
See Figures 1, 2, 3.
tAA (Note 2)
SCL Low to SDA Data Out Valid
tBUF (Note 2)
Time the Bus Free Before Start of New
Transmission
tLOW
Clock Low Time
1.3
1200
(Note 18)
µs
tHIGH
Clock High Time
0.6
1200
(Note 18)
µs
tSU:STA
Start Condition Set-up Time
600
ns
tHD:STA
Start Condition Hold Time
600
ns
tSU:DAT
Data In Set-up Time
100
ns
tHD:DAT
Data In Hold Time
0
µs
tSU:STO
Stop Condition Set-up Time
600
ns
tDH
Data Output Hold Time
50
ns
tR (Note 2)
SDA and SCL Rise Time
20 +0.1Cb
(Note 16)
300
ns
tF (Note 2)
SDA and SCL Fall Time
20 +0.1Cb
(Note 16)
300
ns
tSU:WP (Note 2)
WP Set-up Time
600
ns
tHD:WP (Note 2)
WP Hold Time
600
ns
Cb (Note 2)
Capacitive Load for Each Bus Line
1300
ns
400
pF
2-Wire Interface Test Conditions
Input Pulse Levels
10% to 90% of VCC
Input Rise and Fall Times, between 10% and 90%
10ns
Input and Output Timing Threshold Level
1.4V
External Load at Pin SDA
2.3kΩ to VCC and 100pF to VSS
6
FN8216.3
February 20, 2008
X96012
Nonvolatile WRITE Cycle Timing
SYMBOL
PARAMETER
tWC (Note 17)
MIN
(Note 3)
TEST CONDITIONS
Nonvolatile Write Cycle Time
See Figure 3
TYP
MAX
(Note 3)
UNITS
5
10
ms
NOTES:
16. Cb = total capacitance of one bus line (SDA or SCL) in pF.
17. tWC is the time from a valid STOP condition at the end of a write sequence to the end of the self-timed internal nonvolatile write cycle. It is the
minimum cycle time to be allowed for any nonvolatile write by the user, unless Acknowledge Polling is used.
18. The minimum frequency requirement applies between a START and a STOP condition.
Timing Diagrams
tHIGH
tF
SCL
tLOW
tR
tSU:DAT
tSU:STA
tHD:DAT
tSU:STO
tHD:STA
SDA IN
tAA
tDH
tBUF
SDA OUT
FIGURE 1. BUS TIMING
STOP
START
SCL
CLK 1
SDA IN
tSU:WP
tHD:WP
WP
FIGURE 2. WP PIN TIMING
7
FN8216.3
February 20, 2008
X96012
SCL
SDA
8TH BIT OF LAST BYTE
ACK
tWC
START CONDITION
STOP
CONDITION
FIGURE 3. NON-VOLATILE WRITE CYCLE TIMING
Intersil Sensor Conditioner Product Family
FSO = Full Scale Output, Ext = External, Int = Internal.
FEATURES/FUNCTIONS
DEVICE
TITLE
EXTERNAL INTERNAL
INTERNAL
VOLTAGE
SENSOR
TEMPERATURE
REFERENCE
INPUT
SENSOR
VREF
I/O
GENERAL
PURPOSE
EEPROM
LOOK-UP
TABLE
ORGANIZATION
# OF
DACS
FSO
CURRENT
DAC
SETTING
RESISTORS
X96010 Sensor Conditioner
with Dual Look-Up
Table Memory and
DACs
No
Yes
Yes
Yes
No
Dual Bank
Dual
Ext
X96011 Temperature Sensor
with Look-Up Table
Memory and DAC
Yes
No
Yes
No
No
Single Bank
Single
Int
X96012 Universal Sensor
Conditioner with
Dual Look-Up Table
Memory and DACs
Yes
Yes
Yes
Yes
Yes
Dual Bank
Dual
Ext/Int
Device Description
The X96012 combines two Programmable Current
Generators, and integrated EEPROM with Block Lock™
protection in one package. The combination of the X96012
functionality and Intersil’s QFN package lowers system cost,
increases reliability, and reduces board space requirements.
Two on-chip Programmable Current Generators may be
independently programmed to either sink or source current.
The maximum current generated is determined by using an
externally connected programming resistor, or by selecting
one of three predefined values. Both current generators
have a maximum output of ±3.2mA, and may be controlled
to an absolute resolution of 0.39% (256 steps/8-bit).
Both current generators may be driven using an on-board
temperature sensor, an external sensor, or Control
Registers. The internal temperature sensor operates over a
very broad temperature range (-40°C to +100°C). The
8
sensor output (internal or external) drives an 8-bit A/D
converter. The six MSBs of the ADC output select one of
64 bytes from each nonvolatile look-up table (LUT).
The contents of the selected LUT row (8-bit wide) drives the
input of an 8-bit D/A converter, which generates the output
current.
All control and set-up parameters of the X96012, including
the look-up tables, are programmable via the 2-wire serial
port.
The general purpose memory portion of the device is a
CMOS serial EEPROM array with Intersil’s Block Lock™
protection.
The EEPROM array is internally organized as 272x8 bits
with 16-Byte pages, and utilizes Intersil’s proprietary Direct
Write™ cells, providing a minimum endurance of 100,000
Page Write cycles and a minimum data retention of 100
years.
FN8216.3
February 20, 2008
X96012
Principles of Operation
VRM: VOLTAGE REFERENCE PIN MODE (NON-VOLATILE)
Control and Status Registers
The Control and Status Registers provide the user with a
mechanism for changing and reading the value of various
parameters of the X96012. The X96012 contains seven
Control, one Status, and several Reserved registers, each
being one Byte wide. (Figure 4). The Control registers
0 through 6 are located at memory addresses 80h through
86h respectively. The Status register is at memory address
87h, and the Reserved registers at memory address 88h
through 8Fh.
All bits in Control register 6 always power-up to the logic
state “0”. All bits in Control registers 0 through 5 power-up to
the logic state value kept in their corresponding nonvolatile
memory cells. The nonvolatile bits of a register retain their
stored values even when the X96012 is powered down, then
powered back up. The nonvolatile bits in Control 0 through
Control 5 registers are all preprogrammed to the logic state
“0” at the factory.
Bits indicated as “Reserved” are ignored when read, and
must be written as “0”, if any Write operation is performed to
their registers.
A detailed description of the function of each of the Control
and Status register bits follows:
Control Register 0
This register is accessed by performing a Read or Write
operation to address 80h of memory.
BL1, BL0: BLOCK LOCK PROTECTION BITS
(NON-VOLATILE)
These two bits are used to inhibit any write operation to
certain addresses within the memory array. The protected
region of memory is determined by the values of the two bits,
as shown in Table 1.
BL1
BL0
TABLE 1.
PROTECTED
ADDRESSES (SIZE)
PARTITION OF
ARRAY LOCKED
0
0
None (Default)
None (Default)
0
1
00h to 7Fh (128 bytes)
GPM
1
0
00h to 7Fh and 90h to CFh
(192 bytes)
GPM, LUT1
1
1
00h to 7Fh and 90h to 10Fh
(256 bytes)
GPM, LUT1, LUT2
If the user attempts to perform a write operation to a
protected region of memory, the operation is aborted without
changing any data in the array.
Notice that if the Write Protect (WP) input pin of the X96012
is active (LOW), then any write operation to the memory is
inhibited, irrespective of the Block Lock bit settings.
9
The VRM bit configures the Voltage Reference pin (VREF)
as either an input or an output. When the VRM bit is set to
“0” (default), the voltage at pin VREF is an output from the
X96012’s internal voltage reference. When the VRM bit is
set to “1”, the voltage reference for the VREF pin is external.
See Figure 5.
ADCIN: A/D CONVERTER INPUT SELECT
(NON-VOLATILE)
The ADCIN bit selects the input of the on-chip A/D converter.
When the ADCIN bit is set to “0” (default), the output of the
on-chip temperature sensor is the input to the A/D converter.
When the ADCIN bit is set to “1”, the input to the A/D
converter is the voltage at the VSENSE pin. See Figure 7.
ADCFILTOFF: ADC FILTERING CONTROL
(NON-VOLATILE)
When this bit is “1”, the status register at 87h is updated after
every conversion of the ADC. When this bit is “0” (default),
the status register is updated after four consecutive
conversions with the same result, on the 6 MSBs.
NV1234: CONTROL REGISTERS 1, 2, 3 AND 4
VOLATILITY MODE SELECTION BIT (NON-VOLATILE)
When the NV1234 bit is set to “0” (default), bytes written to
Control registers 1, 2, 3, and 4 are stored in volatile cells,
and their content is lost when the X96012 is powered down.
When the NV1234 bit is set to “1”, bytes written to Control
registers 1, 2, 3, and 4 are stored in both volatile and
nonvolatile cells, and their value doesn’t change when the
X96012 is powered down and powered back up. See
“Writing to Control Registers” on page 20.
I1DS: CURRENT GENERATOR 1 DIRECTION SELECT BIT
(NON-VOLATILE)
The I1DS bit sets the polarity of Current Generator 1, DAC1.
When this bit is set to “0” (default), the Current Generator 1
of the X96012 is configured as a Current Source. Current
Generator 1 is configured as a Current Sink when the I1DS
bit is set to “1”. See Figure 8.
I2DS: CURRENT GENERATOR 2 DIRECTION SELECT BIT
(NON-VOLATILE)
The I2DS bit sets the polarity of Current Generator 2, DAC2.
When this bit is set to “0” (default), the Current Generator 2
of the X96012 is configured as a Current Source. Current
Generator 2 is configured as a Current Sink when the I2DS
bit is set to “1”. See Figure 8.
Control Register 1
This register is accessed by performing a Read or Write
operation to address 81h of memory. This byte’s volatility is
determined by bit NV1234 in Control register 0.
FN8216.3
February 20, 2008
X96012
L1DA5 - L1DA0: LUT1 DIRECT ACCESS BITS
When bit L1DAS (bit 4 in Control register 5) is set to “1”,
LUT1 is addressed by these six bits, and it is not addressed
by the output of the on-chip A/D converter. When bit L1DAS
is set to “0”, these six bits are ignored by the X96012. See
Figure 10.
A value between 00h (0010) and 3Fh (6310) may be written to
these register bits, to select the corresponding row in LUT1.
The written value is added to the base address of LUT1
(90h).
Control Register 2
This register is accessed by performing a read or write
operation to address 82h of memory. This byte’s volatility is
determined by bit NV1234 in Control register 0.
L2DA5 - L2DA0: LUT2 DIRECT ACCESS BITS
When bit L2DAS (bit 6 in Control register 5) is set to “1”,
LUT2 is addressed by these six bits, and it is not addressed
by the output of the on-chip A/D converter. When bit L2DAS
is set to “0”, these six bits are ignored by the X96012. See
Figure 10.
A value between 00h (0010) and 3Fh (6310) may be written to
these register bits, to select the corresponding row in LUT2.
The written value is added to the base address of LUT2
(D0h).
Control Register 3
This register is accessed by performing a Read or Write
operation to address 83h of memory. This byte’s volatility is
determined by bit NV1234 in Control register 0.
D1DA7 - D1DA0: D/A 1 DIRECT ACCESS BITS
When bit D1DAS (bit 5 in Control register 5) is set to “1”, the
input to the D/A converter 1 is the content of bits D1DA7 D1DA0, and it is not a row of LUT1. When bit D1DAS is set
to “0” (default) these eight bits are ignored by the X96012.
See Figure 9.
10
FN8216.3
February 20, 2008
X96012
BYTE
ADDRESS
80h
NON-VOLATILE
MSB
LSB
3
7
6
5
4
I2DS
I1DS
NV1234
ADCfiltOff
CONTROL
1, 2, 3, 4
VOLATILITY
0: VOLATILE
1: NONVOLATILE
ADC
FILTERING
0: ON
1: OFF
L1DA5
L1DA4
L1DA3
L1DA2
L1DA1
L1DA0
CONTROL 1
L2DA5
L2DA4
L2DA3
L2DA2
L2DA1
L2DA0
CONTROL 2
D1DA5
D1DA4
D1DA3
D1DA2
D1DA1
D1DA0
CONTROL 3
CONTROL 4
I1 AND I2 DIRECTION
0: SOURCE
1: SINK
2
ADCIN
VRM
ADC INPUT VOLTAGE
0: INTERNAL REFERENCE
1: EXTERNALMODE
0: INTERNAL
1: EXTERNAL
1
0
BL1
BL0
REGISTER
NAME
CONTROL 0
BLOCK LOCK
00: NONE LOCKED
01: GPM LOCKED
10: GPM, LUT1, LOCKED
11: GPM, LUT1, LUT2
LOCKED
DIRECT ACCESS TO LUT1
81h
VOLATILE OR
NON-VOLATILE
RESERVED
RESERVED
DIRECT ACCESS TO LUT2
82h
VOLATILE OR
NON-VOLATILE
RESERVED
RESERVED
DIRECT ACCESS TO DAC1
83h
VOLATILE OR
NON-VOLATILE
D1DA7
D1DA6
DIRECT ACCESS TO DAC2
84h
VOLATILE OR
NON-VOLATILE
D2DA7
D2DA6
D2DA5
D2DA4
D2DA3
D2DA2
D2DA1
D2DA0
85h
NON-VOLATILE
D2DAS
L2DAS
D1DAS
L1DAS
I2FSO1
I2FSO0
I1FSO1
I1FSO0
DIRECT
ACCESS
TO DAC2
0: DISABLED
1: ENABLED
86h
VOLATILE
WEL
DIRECT
DIRECT
DIRECT
ACCESS
ACCESS
ACCESS
TO LUT2
TO DAC1
TO LUT1
0: DISABLED 0: DISABLED 0: DISABLED
1: ENABLED 1: ENABLED 1: ENABLED
R2 SELECTION
00: EXTERNAL
01: LOW INTERNAL
10: MIDDLE INTERNAL
11: HIGH INTERNAL
R1 SELECTION
00: EXTERNAL
01: LOW INTERNAL
10: MIDDLE INTERNAL
11: HIGH INTERNAL
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
AD3
AD2
AD1
AD0
RESERVED RESERVED
CONTROL 5
CONTROL 6
WRITE
ENABLE
LATCH
0: WRITE
DISABLED
1: WRITE
ENABLED
ADC OUTPUT
87h
VOLATILE
AD7
AD6
AD5
AD4
STATUS
REGISTERS IN BYTE ADDRESSES 88h THROUGH 8Fh ARE RESERVED.
FIGURE 4. CONTROL AND STATUS REGISTER FORMAT
11
FN8216.3
February 20, 2008
X96012
Control Register 4
This register is accessed by performing a Read or Write
operation to address 84h of memory. This byte’s volatility is
determined by bit NV1234 in Control register 0.
D2DA7 - D2DA0: D/A 2 DIRECT ACCESS BITS
L1DAS: LUT1 DIRECT ACCESS SELECT BIT
(NON-VOLATILE)
When bit L1DAS is set to “0” (default), LUT1 is addressed by
the output of the on-chip A/D converter. When bit L1DAS is
set to “1”, LUT1 is addressed by bits L1DA5 - L1DA0.
When bit D2DAS (bit 7 in Control register 5) is set to “1”, the
input to the D/A converter 1 is the content of bits
D2DA-D2DA0, and it is not a row of LUT2. When bit D2DAS
is set to “0” (default) these eight bits are ignored by the
X96012. See Figure 9.
D1DAS: D/A 1 DIRECT ACCESS SELECT BIT
(NON-VOLATILE)
Control Register 5
L2DAS: LUT2 DIRECT ACCESS SELECT BIT
(NON-VOLATILE)
This register is accessed by performing a Read or Write
operation to address 85h of memory.
I1FSO1 - I1FSO0: CURRENT GENERATOR 1 FULL
SCALE OUTPUT SET BITS (NON-VOLATILE)
These two bits are used to set the full scale output current at
the Current Generator 1 pin, I1. If both bits are set to “0”
(default), an external resistor connected between pin R1 and
VSS, determines the full scale output current available at pin
I1. The other three options are indicated in Table 2. The
direction of this current is set by bit I1DS in Control register
0. See Figure 8.
When bit D1DAS is set to “0” (default), the input to the D/A
converter 1 is a row of LUT1. When bit D1DAS is set to “1”, that
input is the content of the Control register 3.
When bit L2DAS is set to “0” (default), LUT2 is addressed by
the output of the on-chip A/D converter. When bit L2DAS is
set to “1”, LUT2 is addressed by bits L2DA5 - L2DA0.
D2DAS: D/A 2 DIRECT ACCESS SELECT BIT
(NONVOLATILE)
When bit D2DAS is set to “0” (default), the input to the D/A
converter 2 is a row of LUT2. When bit D2DAS is set to “1”, that
input is the content of the Control register 4.
Control Register 6
This register is accessed by performing a Read or Write
operation to address 86h of memory.
TABLE 2.
I1FSO1
I1FSO0
I1 FULL SCALE OUTPUT CURRENT
0
0
Set externally via pin R1 (Default)
0
1
±0.4mA*
1
0
±0.85mA*
1
1
±1.3mA*
NOTE: *No external resistor should be connected in these cases
between R1 and VSS.
I2FSO1 - I2FSO0: CURRENT GENERATOR 2 FULL
SCALE OUTPUT CURRENT SET BITS (NON-VOLATILE)
These two bits are used to set the full scale output current at
the Current Generator 2 pin, I2. If both bits are set to “0”
(default), an external resistor connected between pin R2 and
Vss, determines the full scale output current available at pin
I2. The other three options are indicated Table 3. The direction
of this current is set by bit I2DS in Control Register 0.
TABLE 3.
I2FSO1
I2FSO2
I2 FULL SCALE OUTPUT CURRENT
0
0
Set externally via pin R2 (Default)
0
1
±0.4mA*
1
0
±0.85mA*
1
1
±1.3mA*
WEL: WRITE ENABLE LATCH (VOLATILE)
The WEL bit controls the Write Enable status of the entire
X96012 device. This bit must be set to “1” before any other
Write operation (volatile or nonvolatile). Otherwise, any
proceeding Write operation to memory is aborted and no ACK
is issued after a Data Byte.
The WEL bit is a volatile latch that powers up in the “0” state
(disabled). The WEL bit is enabled by writing 100000002 to
Control register 6. Once enabled, the WEL bit remains set to “1”
until the X96012 is powered down, and then up again, or until it
is reset to “0” by writing 000000002 to Control register 6.
A Write operation that modifies the value of the WEL bit will not
cause a change in other bits of Control register 6.
Status Register - ADC Output
This register is accessed by performing a Read operation to
address 87h of memory.
AD7 - AD0: A/D CONVERTER OUTPUT BITS (READ
ONLY)
These eight bits are the binary output of the on-chip A/D
converter. The output is 000000002 for minimum input and
111111112 for full scale input. The six MSBs select a row of
the LUTs.
NOTE: *No external resistor should be connected in these cases
between R2 and VSS.
12
FN8216.3
February 20, 2008
X96012
Voltage Reference
The A/D converter input voltage range (VINADC) is from 0V
to V(VREF).
The voltage reference to the A/D and D/A converters on the
X96012, may be driven from the on-chip voltage reference,
or from an external source via the VREF pin. Bit VRM in
Control Register 0 selects between the two options. See
Figure 5.
A/D Converter Input Select
The input signal to the A/D converter on the X96012, may be
the output of the on-chip temperature sensor, or an external
source via the VSENSE pin. Bit ADCIN in Control register 0
selects between the two options. See Figure 7. It’s default
value is “0”, which selects the internal temperature sensor.
The default value of VRM is “0”, which selects the internal
reference. When the internal reference is selected, it’s
output voltage is also an output at pin VREF with a nominal
value of 1.21 V. If an external voltage reference is preferred,
the VRM bit of the Control Register 0 must be set to “1”.
If an external source is intended as the input to the A/D
converter, the ADCIN bit of the Control register 0 must be set
to “1”.
VRM: BIT 2 IN CONTROL REGISTER 0
A/D Converter Range
ADCIN: BIT 3 IN CONTROL REGISTER 0.
ON-CHIP
VOLTAGE
REFERENCE
VREF PIN
VSENSE
PIN
A/D CONVERTER AND
D/A CONVERTERS REFERENCE
TO A/D
CONVERTER
INPUT
ON-CHIP
TEMPERATURE
SENSOR
FIGURE 5. VOLTAGE REFERENCE STRUCTURE
A/D Converter
VREF
FIGURE 7. A/D CONVERTER INPUT SELECT STRUCTURE
The X96012 contains a general purpose, on-chip, 8-bit
Analog to Digital (A/D) converter whose output is available at
the Status Register as bits AD[7:0]. By default these output
bits are used to select a row in the look-up tables associated
with the X96012’s Current Generators. When bit ADCfiltOff
is “0” (default), bits AD[7:0] are updated each time the ADC
performs four consecutive conversions with the same exact
result at the 6 MSBs. When bit ADCfiltOff is “1”, these bits
are updated after every ADC conversion.
From Figure 6 we can see that the operating range of the
A/D converter input depends on the voltage reference. And
from Figure 7 we see that the internal temperature Sensor
output also varies with the voltage reference (VREF).
Table 4 summarizes the voltage range restrictions on the
VSENSE and VREF pins in different configurations.
TABLE 4. VSENSE AND VREF RANGES
A block diagram of the A/D converter is shown in Figure 6.
The voltage reference input (see “Voltage Reference” on
page 13), sets the maximum amplitude of the ramp
generator output. The A/D converter input signal (see “A/D
Converter Input Select” on page 13 for details) is compared
to the ramp generator output. The control and encode logic
produces a binary encoded output, with a minimum value of
00h (010), and a full scale output value of FFh (25510).
VREF
A/D CONVERTER INPUT
RANGES
Internal
Internal Temp Sensor
Internal
VSense Pin
0 ≤ V(VSense) ≤
V(VREF)
External
VSense Pin
0 ≤ V(VREF) ≤ 1.3 V
0 ≤ V(VSense) ≤V(VREF)
External
Internal Temp. Sensor
Not Applicable
Not a Valid Case
All voltages referred to VSS
COMPARATOR
A/D CONVERTER INPUT
8
CONTROL AND
ENCODE LOGIC
FROM VREF
RAMP
GENERATOR
CONVERSION RESET
A/D CONVERTER
OUTPUT
(TO LUTS
AND STATUS
REGISTER)
CLOCK
13
FN8216.3
February 20, 2008
X96012
Look-Up Tables
Current Generator Block
The X96012 memory array contains two 64-byte look-up
tables. One is associated to pin I1’s output current generator
and the other to pin I2’s output current generator, through
their corresponding D/A converters. The output of each
look-up table is the byte contained in the selected row. By
default these bytes are the inputs to the D/A converters
driving pins I1 and I2.
The Current Generator pins I1 and I2 are outputs of two
independent current mode D/A converters.
D/A Converter Operation
The Block Diagram for each of the D/A converters is shown
in Figure 8.
The input byte of the D/A converter selects a voltage on the
non-inverting input of an operational amplifier. The output of
the amplifier drives the gate of a FET, whose source is
connected to ground via resistor R1 or R2. This node is also
fed back to the inverting input of the amplifier. The drain of
the FET is connected to the output current pin (I1 or I2) via a
“polarity select” circuit block.
The byte address of the selected row is obtained by adding
the look-up table base address (90h for LUT1, and D0h for
LUT2) and the appropriate row selection bits. See Figure 9.
By default, the look-up table selection bits are the 6
MSBs of the A/D converter output. Alternatively, the A/D
converter can be bypassed and the six row selection bits
are the six LSBs of Control Registers 1 and 2, for the
LUT1 and LUT2 respectively. The selection between
these options is illustrated in Figure 10, and described in
“I2DS: Current Generator 2 Direction Select Bit (Non-volatile)”
on page 9, and “Control Register 2” on page 10.
VCC
I1DS OR I2DS: BITS
6 OR 7 IN CONTROL
REGISTER 0.
VOLTAGE
DIVIDER
I1 OR I2 PIN
+
R1 OR R2 PIN
11
VSS
R1_MIDDLE_CURRENT OR
R2_MIDDLE_CURRENT
00
10
VSS
01
R1_LOW_CURRENT OR
R2_LOW_CURRENT
I1FSO[1:0]
OR I2FSO[1:0]
BITS 1 AND 0, OR
3 AND 2 IN CONTROL
REGISTER 5
R1_HIGH_CURRENT OR
R2_HIGH_CURRENT
VREF
DAC1 OR
DAC2
INPUT BYTE
POLARITY
SELECT
CIRCUIT
VSS
R1_EXTERNAL OR R2_EXTERNAL
OPTIONAL EXTERNAL RESISTOR
VSS
FIGURE 8. D/A CONVERTER BLOCK DIAGRAM
14
FN8216.3
February 20, 2008
X96012
D2DA[7:0] : CONTROL REGISTER 4
LUT2
D0H
10FH
6
8
A
D
D
E
R
8
8
D1
8
DAC 2
INPUT BYTE
OUT
D0
…
LUT2 ROW
SELECTION BITS
SELECT
D0H
D2DAS: BIT 7 OF
CONTROL REGISTER 5
D1DA[7:0] : CONTROL REGISTER 3
LUT1
90H
CFH
6
8
A
D
D
E
R
8
8
D1
8
DAC 1
INPUT BYTE
OUT
D0
…
LUT1 ROW
SELECTION BITS
SELECT
90H
D1DAS: BIT 5 OF
CONTROL REGISTER 5
FIGURE 9. LOOK-UP TABLE (LUT) OPERATION
By examining the block diagram in Figure 8, we see that the
maximum current through pin I1 is set by fixing values for
V(VREF) and R1. The output current can then be varied by
changing the data byte at the D/A converter input.
In general, the magnitude of the current at the D/A converter
output pins (I1, I2) may be calculated using Equation 1:
Ix = ( V • ( Vref ) ⁄ ( 384 • Rx ) ) • N
(EQ. 1)
where x = 1, 2 and N is the decimal representation of the
input byte to the corresponding D/A converter.
The value for the resistor Rx (x = 1, 2) determines the full
scale output current that the D/A converter may sink or
source. The full scale output current has a maximum value of
±3.2mA, which is obtained using a resistance of 255Ω for Rx.
This resistance may be connected externally to pin Rx of the
X96012, or may be selected from one of three internal values.
Bits I1FSO1 and I1FSO0 select the full scale output current
setting for I1 as described in “I1FSO1 - I1FSO0: Current
Generator 1 Full Scale Output Set Bits (Non-volatile)” on
page 12. Bits I2FSO1 and I2FSO0 select the maximum
current setting for I2. When an internal resistor is selected for
R1 or R2, then no resistor should be connected externally at
the corresponding pin.
Bits I1DS and I2DS in Control Register 0 select the direction
of the currents through pins I1 and I2 independently (see
“I1DS: Current Generator 1 Direction Select Bit (Non-volatile)”
on page 9 and “Control and Status Registers” on page 9).
D/A Converter Output Current Response
When the D/A converter input data byte changes by an
arbitrary number of bits, the output current changes from an
initial current level (Ix) to some final level (Ix + ΔIx). The
transition is monotonic and glitchless.
D/A Converter Control
The data byte inputs of the D/A converters can be controlled
in three ways:
1) With the A/D converter and through the look-up tables
(default),
2) Bypassing the A/D converter and directly accessing the
look-up tables,
3) Bypassing both the A/D converter and look-up tables, and
directly setting the D/A converter input byte.
The options are summarized in Tables 5 and 6.
TABLE 5. D/A CONVERTER 1 ACCESS SUMMARY
L1DAS
D1DAS
CONTROL SOURCE
0
0
A/D converter through LUT1 (Default)
1
0
Bits L1DA5 - L1DA0 through LUT1
X
1
Bits D1DA7 - D1DA0
NOTE: “X” = Don’t Care Condition (May be either “1” or “0”)
TABLE 6. D/A CONVERTER 2 ACCESS SUMMARY
L2DAS
D2DAS
CONTROL SOURCE
0
0
A/D converter through LUT2 (Default)
1
0
Bits L2DA5 - L2DA0 through LUT2
X
1
Bits D2DA7 - D2DA0
NOTE: “X” = Don’t Care Condition (May be either “1” or “0”)
15
FN8216.3
February 20, 2008
X96012
VOLTAGE
VCC
VADCOK
0V
TIME
CURRENT
IX
ADC TIME
IX X 10%
TIME
FIGURE 11. D/A CONVERTER POWER-ON RESET RESPONSE
L2DA[5:0]:
CONTROL
REGISTER 2
VOLTAGE
REFERENCE
D1
OUT
D0
LUT2 ROW
SELECTION BITS
SELECT
6
ADC
VOLTAGE INPUT
L2DAS: BIT 6 IN
CONTROL REGISTER 5
8
AD[7:0]
STATUS
REGISTER
L1DA[5:0]:
CONTROL
REGISTER 1
6
D1
OUT
D0
SELECT
LUT1 ROW
SELECTION BITS
L1DAS: BIT 4 IN
CONTROL REGISTER 5
FIGURE 10. LOOK-UP TABLE ADDRESSING
The A/D converter is shared between the two current
generators but the look-up tables, D/A converters, control
bits, and selection bits can be set completely independently.
Bits D1DAS and D2DAS are used to bypass the A/D
converter and look-up tables, allowing direct access to the
inputs of the D/A converters with the bytes in control
registers 3 and 4 respectively. See Figure 9 and the
descriptions of the control bits starting on page 9.
Bits I1DS and I2DS in Control Register 0 select the direction
of the currents through pins I1 and I2 independently See
Figure 8 and the descriptions of the control bits starting on
page 9.
16
Power-on Reset
When power is applied to the VCC pin of the X96012, the
device undergoes a strict sequence of events before the
current outputs of the D/A converters are enabled.
When the voltage at VCC becomes larger than the power-on
reset threshold voltage (VPOR), the device recalls all control
bits from non-volatile memory into volatile registers. Next,
the analog circuits are powered up. When the voltage at Vcc
becomes larger than a second voltage threshold (VADCOK),
the ADC is enabled. In the default case, after the ADC
performs four consecutive conversions with the same exact
result, the ADC output is used to select a byte from each
look-up table. Those bytes become the input of the DACs.
FN8216.3
February 20, 2008
X96012
During all the previous sequence the input of both DACs are
00h. If bit ADCfiltOff is “1”, only one ADC conversion is
necessary. Bits D1DAS, D2DAS, L1DAS, and L2DAS, also
modify the way the two DACs are accessed the first time
after power-up, as described in “Control Register 5” on
page 12.
The X96012 is a hot pluggable device. Voltage disturbances
on the VCC pin are handled by the power-on reset circuit,
allowing proper operation during hot plug-in applications.
Serial Interface
Serial Interface Conventions
The device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the slave.
The master always initiates data transfers, and provides the
clock for both transmit and receive operations. The X96012
operates as a slave in all applications.
Serial Stop Condition
All communications must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH. The STOP condition is also used to place the
device into the Standby power mode after a read sequence.
A STOP condition can only be issued after the transmitting
device has released the bus. See Figure 12.
Serial Acknowledge
An ACK (Acknowledge), is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the bus after transmitting
eight bits. During the ninth clock cycle, the receiver pulls the
SDA line LOW to acknowledge the reception of the eight bits
of data. See Figure 14.
The device responds with an ACK after recognition of a
START condition followed by a valid Slave Address byte. A
valid Slave Address byte must contain the Device Type
Identifier 1010, and the Device Address bits matching the
logic state of pins A2, A1, and A0. See Figure16.
If a write operation is selected, the device responds with an
ACK after the receipt of each subsequent 8-bit word.
Serial Clock and Data
Data states on the SDA line can change only while SCL is
LOW. SDA state changes while SCL is HIGH are reserved
for indicating START and STOP conditions. See Figure 13.
On power-up of the X96012, the SDA pin is in the input
mode.
Serial Start Condition
All commands are preceded by the START condition, which
is a HIGH to LOW transition of SDA while SCL is HIGH. The
device continuously monitors the SDA and SCL lines for the
START condition and does not respond to any command
until this condition has been met. See Figure 12.
In the read mode, the device transmits eight bits of data,
releases the SDA line, and then monitors the line for an
ACK. The device continues transmitting data if an ACK is
detected. The device terminates further data transmissions if
an ACK is not detected. The master must then issue a STOP
condition to place the device into a known state.
The X96012 acknowledges all incoming data and address
bytes except: 1) The “Slave Address Byte” when the “Device
Identifier” or “Device Address” are wrong; 2) All “Data Bytes”
when the “WEL” bit is “0”, with the exception of a “Data Byte”
addresses to location 86h; 3) “Data Bytes” following a “Data
Byte” addressed to locations 80h, 85h, or 86h.
SCL
SDA
STOP
START
FIGURE 12. VALID START AND STOP CONDITIONS
SCL
SDA
DATA STABLE
DATA CHANGE
DATA STABLE
FIGURE 13. VALID DATA CHANGES ON THE SDA BUS
17
FN8216.3
February 20, 2008
X96012
SCL FROM
MASTER
1
8
9
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
START
ACK
FIGURE 14. ACKNOWLEDGE RESPONSE FROM RECEIVER
X96012 Memory Map
The X96012 contains a 2176 bit array of mixed volatile and
nonvolatile memory. This array is split up into four distinct
parts, namely: (Refer to Figure 15).
Both look-up tables LUT1 and LUT2 are realized as
non-volatile EEPROM, and extend from memory locations
90h - CFh and D0h - 10Fh respectively. These look-up tables
are dedicated to storing data solely for the purpose of setting
the outputs of Current Generators I1 and I2 respectively.
• General Purpose Memory (GPM)
All bits in both look-up tables are preprogrammed to “0” at the
factory.
• Look-up Table 1 (LUT1)
• Look-up Table 2 (LUT2)
Addressing Protocol Overview
• Control and Status Registers
The GPM is all nonvolatile EEPROM, located at memory
addresses 00h to 7Fh.
ADDRESS
SIZE
10FH
FFH
LOOK-UP TABLE 2
(LUT2)
64 BYTES
LOOK-UP TABLE 1
(LUT1)
64 BYTES
CONTROL AND STATUS
16 BYTES
D0H
CFH
90H
8FH
REGISTERS
80H
7FH
GENERAL PURPOSE
128 BYTES
MEMORY (GPM)
All Serial Interface operations must begin with a START,
followed by a Slave Address Byte. The Slave address
selects the X96012, and specifies if a Read or Write
operation is to be performed.
It should be noted that the Write Enable Latch (WEL) bit must
first be set in order to perform a Write operation to any other bit.
See “WEL: Write Enable Latch (Volatile)” on page 12. Also, all
communication to the X96012 over the 2-wire serial bus is
conducted by sending the MSB of each byte of data first.
Even though the 2176 bit memory consists of four differing
functions, it is physically realized as one contiguous array,
organized as 17 pages of 16 bytes each.
The X96012 2-wire protocol provides one address byte,
therefore, only 256 bytes can be addressed directly. The
next few sections explain how to access the different areas
for reading and writing.
00H
7
0
FIGURE 15. X96012 MEMORY MAP
The Control and Status registers of the X96012 are used in
the test and setup of the device in a system. These registers
are realized as a combination of both volatile and nonvolatile
memory. These registers reside in the memory locations 80h
through 8Fh. The reserved bits within registers 80h through
86h, must be written as “0” if writing to them, and should be
ignored when reading. The reserved registers, from 88h
through 8Fh, must not be written, and their content should
be ignored.
SA7
1
SA6
SA5
SA4
SA3
SA2
SA1
0
1
0
AS2
AS1
AS0
DEVICE TYPE
IDENTIFIER
SLAVE ADDRESS
BIT(S)
DEVICE
ADDRESS
R/W
READ OR
WRITE
DESCRIPTION
SA7 - SA4
Device Type Identifier
SA3 - SA1
Device Address
SA0
SA0
Read or Write Operation Select
FIGURE 16. SLAVE ADDRESS (SA) FORMAT
18
FN8216.3
February 20, 2008
X96012
Slave Address Byte
Following a START condition, the master must output a
Slave Address Byte. Refer to Figure 16. This byte includes
three parts:
• The four MSBs (SA7 - SA4) are the Device Type
Identifier, which must always be set to 1010 in order to
select the X96012.
• The next three bits (SA3 - SA1) are the Device Address bits
(AS2 - AS0). To access any part of the X96012’s memory,
the value of bits AS2, AS1, and AS0 must correspond to the
logic levels at pins A2, A1, and A0 respectively.
• The LSB (SA0) is the R/W bit. This bit defines the operation
to be performed on the device being addressed. When the
R/W bit is “1”, then a Read operation is selected. A “0”
selects a Write operation (refer to Figure 16).
BYTE LOAD COMPLETED BY ISSUING
STOP. ENTER ACK POLLING
ISSUE START
ISSUE SLAVE
ADDRESS BYTE
(READ OR WRITE)
ISSUE STOP
NO
YES
NO
In order to perform a Byte Write operation to the memory
array, the Write Enable Latch (WEL) bit of the Control 6
Register must first be set to “1”. See “WEL: Write Enable
Latch (Volatile)” on page 12.
For any Byte Write operation, the X96012 requires the Slave
Address Byte, an Address Byte, and a Data Byte. See
Figure 18. After each of them, the X96012 responds with an
ACK. The master then terminates the transfer by generating a
STOP condition. At this time, if all data bits are volatile, the
X96012 is ready for the next read or write operation. If some
bits are nonvolatile, the X96012 begins the internal write cycle
to the nonvolatile memory. During the internal nonvolatile write
cycle, the X96012 does not respond to any requests from the
master. The SDA output is at high impedance.
Writing to Control bytes which are located at byte addresses
80h through 8Fh is a special case described in “Writing to
Control Registers” on page 20.
Page Write Operation
YES
ISSUE STOP
CONTINUE NORMAL READ OR
WRITE COMMAND SEQUENCE
PROCEED
FIGURE 17. ACKNOWLEDGE POLLING SEQUENCE
Nonvolatile Write Acknowledge Polling
After a nonvolatile write command sequence is correctly
issued (including the final STOP condition), the X96012
initiates an internal high voltage write cycle. This cycle
typically requires 5ms. During this time, any Read or Write
command is ignored by the X96012. Write Acknowledge
Polling is used to determine whether a high voltage write
cycle is completed.
19
Byte Write Operation
A Byte Write operation can access bytes at locations 00h
through FEh directly, when setting the Address Byte to 00h
through FEh respectively. Setting the Address Byte to FFh
accesses the byte at location 100h. The other sixteen bytes,
at locations FFh and 101h through 10Fh can only be
accessed using Page Write operations. The byte at location
FFh can only be written using a “Page Write” operation.
ACK RETURNED?
HIGH VOLTAGE
COMPLETE. CONTINUE COMMAND
SEQUENCE.
During acknowledge polling, the master first issues a START
condition followed by a Slave Address Byte. The Slave
Address Byte contains the X96012’s Device Type Identifier
and Device Address. The LSB of the Slave Address (R/W)
can be set to either 1 or 0 in this case. If the device is busy
within the high voltage cycle, then no ACK is returned. If the
high voltage cycle is completed, an ACK is returned and the
master can then proceed with a new Read or Write
operation. Refer to Figure 17.
The 2176-bit memory array is physically realized as one
contiguous array, organized as 17 pages of 16 bytes each. A
“Page Write” operation can be performed to any of the GPM
or LUT pages. In order to perform a Page Write operation to
the memory array, the Write Enable Latch (WEL) bit in
Control register 6 must first be set See “WEL: Write Enable
Latch (Volatile)” on page 12.
A Page Write operation is initiated in the same manner as
the byte write operation; but instead of terminating the write
cycle after the first data byte is transferred, the master can
transmit up to 16 bytes (see Figure 19). After the receipt of
each byte, the X96012 responds with an ACK, and the
internal byte address counter is incremented by one. The
page address remains constant. When the counter reaches
the end of the page, it “rolls over” and goes back to the first
byte of the same page.
FN8216.3
February 20, 2008
X96012
WRITE
S
T
A
R
T
SIGNALS FROM
THE MASTER
SIGNAL AT SDA
1 0 1 0
S
T
O
P
DATA
BYTE
ADDRESS
BYTE
SLAVE
ADDRESS
0
SIGNALS FROM
THE SLAVE
A
C
K
A
C
K
A
C
K
FIGURE 18. BYTE WRITE SEQUENCE
WRITE
S
T
A
R
T
SIGNALS FROM
THE MASTER
2 < n < 16
ADDRESS
BYTE
SLAVE
ADDRESS
DATA BYTE (1)
S
T
O
P
DATA BYTE (N)
SIGNAL AT SDA
1 0 1 0
SIGNALS FROM
THE SLAVE
0
A
C
K
A
C
K
A
C
K
A
C
K
FIGURE 19. PAGE WRITE OPERATION
5 BYTES
5 BYTES
7 BYTES
ADDRESS = 0
ADDRESS = 6
ADDRESS = 11
ADDRESS = 7
ADDRESS POINTER
ENDS UP HERE
ADDRESS = 15
FIGURE 20. EXAMPLE: WRITING 12 BYTES TO A 16-BYTE PAGE STARTING AT LOCATION 11
For example, if the master writes 12 bytes to a 16-byte page
starting at location 11 (decimal), the first 5 bytes are written
to locations 11 through 15, while the last 7 bytes are written
to locations 0 through 6 within that page. Afterwards, the
address counter would point to location 7. If the master
supplies more than 16 bytes of data, then new data
overwrites the previous data, one byte at a time. See
Figure 20.
The master terminates the loading of Data Bytes by issuing
a STOP condition, which initiates the nonvolatile write cycle.
As with the Byte Write operation, all inputs are disabled until
completion of the internal write cycle.
A Page Write operation cannot be performed on the page at
locations 80h through 8Fh. The next section describes the
special cases within that page.
20
A Page Write operation starting with byte address FFh,
accesses the page between locations 100h and 10Fh. The
first data byte of such operation is written to location 100h.
Writing to Control Registers
The byte at location 80h, 85h, and 86h are written using Byte
Write operations. They cannot be written using a Page Write
operation.
Control bytes 1 through 4, at locations 81h through 84h
respectively, are written during a single operation (see
Figure 21). The sequence must be: a START, followed by a
Slave Address byte, with the R/W bit equal to “0”, followed by
81h as the Address Byte, and then followed by exactly four
Data Bytes, and a STOP condition. The first data byte is
written to location 81h, the second to 82h, the third to 83h,
and the last one to 84h.
FN8216.3
February 20, 2008
X96012
Read Operation
The four registers Control 1 through 4, have a nonvolatile
and a volatile cell for each bit. At power-up, the content of
the nonvolatile cells is automatically recalled and written to
the volatile cells. The content of the volatile cells controls the
X96012’s functionality. If bit NV1234 in the Control 0 register
is set to “1”, a Write operation to these registers writes to
both the volatile and nonvolatile cells. If bit NV1234 in the
Control 0 register is set to “0”, a Write operation to these
registers only writes to the volatile cells. In both cases the
newly written values effectively control the X96012, but in
the second case, those values are lost when the part is
powered down.
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (see Figure 22). The master
initiates the operation issuing the following sequence: a
START, the Slave Address byte with the R/W bit set to “0”,
an Address Byte, a second START, and a second Slave
Address byte with the R/W bit set to “1”. After each of the
three bytes, the X96012 responds with an ACK. Then the
X96012 transmits Data Bytes as long as the master
responds with an ACK during the SCL cycle following the
eighth bit of each byte. The master terminates the read
operation (issuing a STOP condition) following the last bit of
the last Data Byte. See Figure 22.
If bit NV1234 is set to “0”, a Byte Write operation to Control
registers 0 or 5 causes the value in the nonvolatile cells of
Control registers 1 through 4 to be recalled into their
corresponding volatile cells, as during power-up. This
doesn’t happen when the WP pin is LOW, because Write
Protection is enabled. It is generally recommended to
configure Control registers 0 and 5 before writing to Control
registers 1 through 4.
The Data Bytes are from the memory location indicated by
an internal pointer. This pointer initial value is determined by
the Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 10Fh the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
When reading any of the control registers 1, 2, 3, or 4, the
Data Bytes are always the content of the corresponding
nonvolatile cells, even if bit NV1234 is "0". See “Control and
Status Registers” on page 9.
A Read operation internal pointer can start at any memory
location from 00h through FEh, when the Address Byte is
00h through FEh respectively. But it starts at location 100h if
the Address Byte is FFh.
When reading any of the control registers 1, 2, 3, or 4, the
Data Bytes are always the content of the corresponding
nonvolatile cells, even if bit NV1234 is "0". See “Control and
Status Registers” on page 9.
FOUR DATA BYTES
WRITE
S
T
A
R
T
SIGNALS FROM
THE MASTER
SLAVE
ADDRESS
DATA BYTE FOR
CONTROL 1
ADDRESS
BYTE = 81h
S
T
O
P
DATA BYTE FOR
CONTROL 4
SIGNAL AT SDA
1 0 1 0
SIGNALS FROM
THE SLAVE
0
1 0 0 0 0 0 0 1
A
C
K
A
C
K
A
C
K
A
C
K
FIGURE 21. WRITING TO CONTROL REGISTERS 1, 2, 3 AND 4
SIGNALS
FROM THE
MASTER
S
T
A
R
T
SIGNAL AT
SDA
SLAVE
ADDRESS
WITH
R/W = 0
1 0 1 0
S
T
A
R
T
ADDRESS
BYTE
1 0 1 0
0
A
C
K
SIGNALS FROM
THE SLAVE
SLAVE
ADDRESS
WITH
R/W = 1
A
C
K
S
T
O
P
A
C
K
1
A
C
K
A
C
K
FIRST READ
DATA BYTE
LAST READ
DATA BYTE
FIGURE 22. READ SEQUENCE
21
FN8216.3
February 20, 2008
X96012
Data Protection
WP: Write Protection Pin
There are four levels of data protection designed into the
X96012:
1- Any Write to the device first requires setting of the WEL bit
in Control 6 register;
2- The Block Lock can prevent Writes to certain regions of
memory;
3- The Write Protection pin disables any writing to the
X96012;
4- The proper clock count, data bit sequence, and STOP
condition is required in order to start a nonvolatile write cycle,
otherwise the X96012 ignores the Write operation.
When the Write Protection (WP) pin is active (LOW), any
Write operations to the X96012 is disabled, except the
writing of the WEL bit.
22
FN8216.3
February 20, 2008
X96012
Thin Shrink Small Outline Plastic Packages (TSSOP)
M14.173
N
INDEX
AREA
E
0.25(0.010) M
E1
2
SYMBOL
3
0.05(0.002)
-A-
INCHES
GAUGE
PLANE
-B1
14 LEAD THIN SHRINK SMALL OUTLINE PLASTIC
PACKAGE
B M
0.25
0.010
SEATING PLANE
L
A
D
-C-
α
e
A1
b
A2
c
0.10(0.004)
0.10(0.004) M
C A M
B S
MIN
1. These package dimensions are within allowable dimensions of
JEDEC MO-153-AC, Issue E.
MILLIMETERS
MIN
MAX
NOTES
A
-
0.047
-
1.20
-
A1
0.002
0.006
0.05
0.15
-
A2
0.031
0.041
0.80
1.05
-
b
0.0075
0.0118
0.19
0.30
9
c
0.0035
0.0079
0.09
0.20
-
D
0.195
0.199
4.95
5.05
3
E1
0.169
0.177
4.30
4.50
4
e
0.026 BSC
0.65 BSC
-
E
0.246
0.256
6.25
6.50
-
L
0.0177
0.0295
0.45
0.75
6
8o
0o
N
NOTES:
MAX
α
14
0o
14
7
8o
Rev. 2 4/06
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm
(0.006 inch) per side.
4. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. Dimension “b” does not include dambar protrusion. Allowable dambar
protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact. (Angles in degrees)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
23
FN8216.3
February 20, 2008