Document 100-1 Chip Inductors – 0805CS (2012) • Exceptional Q values, even at high frequencies • Tight tolerances – 2% for most; 1% for some values Part number1 0805CS-020XJE_ 0805CS-3N0XJE_ 0805CS-030XJE_ 0805CS-050XJE_ 0805CS-060XJE_ 0805CS-070XJE_ 0805CS-080X_E_ 0805CS-100X_E_ 0805CS-120X_E_ 0805CS-150X_E_ 0805CS-180X_E_ 0805CS-220X_E_ 0805CS-240X_E_ 0805CS-270X_E_ 0805CS-330X_E_ 0805CS-360X_E_ 0805CS-390X_E_ 0805CS-430X_E_ 0805CS-470X_E_ 0805CS-560X_E_ 0805CS-680X_E_ 0805CS-820X_E_ 0805CS-910X_E_ 0805CS-101X_E_ 0805CS-111X_E_ 0805CS-121X_E_ 0805CS-151X_E_ 0805CS-181X_E_ 0805CS-221X_E_ 0805CS-241X_E_ 0805CS-271X_E_ 0805CS-331X_E_ 0805CS-391X_E_ 0805CS-471X_E_ 0805CS-561X_E_ 0805CS-681X_E_ 0805CS-821X_E_ Inductance2 (nH) 2.8 @250 MHz 3.0 @250 MHz 3.3 @250 MHz 5.6 @250 MHz 6.8 @250 MHz 7.5 @250 MHz 8.2 @250 MHz 10 @250 MHz 12 @250 MHz 15 @250 MHz 18 @250 MHz 22 @250 MHz 24 @250 MHz 27 @250 MHz 33 @250 MHz 36 @250 MHz 39 @250 MHz 43 @200 MHz 47 @200 MHz 56 @200 MHz 68 @200 MHz 82 @150 MHz 91 @150 MHz 100 @150 MHz 110 @150 MHz 120 @150 MHz 150 @100 MHz 180 @100 MHz 220 @100 MHz 240 @100 MHz 270 @100 MHz 330 @100 MHz 390 @100 MHz 470 @50 MHz 560 @25 MHz 680 @25 MHz 820 @25 MHz • Wirewound construction provides the highest SRFs in 0805 size SRF typ5 Percent DCR max6 Irms7 Color (MHz)(Ohms)(mA) code tolerance3 Q min4 5 5 5 5 5 5 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2,1 5,2 5,2,1 5,2,1 5,2,1 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 1. When ordering, specify tolerance, termination and packaging codes: 0805CS-821XGEC Tolerance: F =1% G = 2% J = 5% (Table shows stock tolerances in bold.) Termination:E =Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. L =RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging:C =7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel). 80 @1500 MHz 65 @1500 MHz 50 @1500 MHz 65 @1000 MHz 50 @1000 MHz 50 @1000 MHz 50 @1000 MHz 60 @500 MHz 50 @500 MHz 50 @500 MHz 50 @500 MHz 55 @500 MHz 50 @500 MHz 55 @500 MHz 60 @500 MHz 55 @500 MHz 60 @500 MHz 60 @500 MHz 60 @500 MHz 60 @500 MHz 60 @500 MHz 65 @500 MHz 65 @500 MHz 65 @500 MHz 50 @250 MHz 50 @250 MHz 50 @250 MHz 50 @250 MHz 50 @250 MHz 44 @250 MHz 48 @250 MHz 48 @250 MHz 48 @250 MHz 33 @100 MHz 23 @50 MHz 23 @50 MHz 23 @50 MHz 12200 12200 12200 5900 5600 4800 4400 4300 4000 3200 3100 2600 2400 2580 2150 1900 2000 1800 1700 1600 1500 1330 1330 1250 1100 1100 920 920 820 770 730 650 600 375 330 310 310 0.06 0.06 0.08 0.08 0.11 0.14 0.12 0.10 0.15 0.17 0.20 0.22 0.22 0.25 0.27 0.27 0.29 0.34 0.31 0.34 0.38 0.42 0.48 0.46 0.48 0.51 0.56 0.64 0.70 1.00 1.00 1.40 1.50 1.76 1.90 2.20 2.35 800 800 600 600 600 600 600 600 600 600 600 500 500 500 500 500 500 500 500 500 500 400 400 400 400 400 400 400 400 350 350 310 290 250 230 190 180 Gray White Black Orange Brown Green Red Blue Orange Yellow Green Blue Gray Violet Gray Orange White Yellow Black Brown Red Orange Black Yellow Brown Green Blue Violet Gray Red White Black Brown Violet Orange Green Blue 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/ HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 5. SRF measured using an Agilent/HP 8720D network analyzer and a Coilcraft SMD‑D test fixture. 6. DCR measured on a Cambridge Technology micro-ohmmeter and a Coilcraft CCF858 test fixture. 7. Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 100-1 Revised 06/11/14 Document 100-2 0805CS Series (2012) Typical Q vs Frequency Typical L vs Frequency 100 12 nH 90 39 nH 22 nH 220 nH 80 6.8 nH 70 Inductance (nH) 68 nH Q Factor 1000 3.3 nH 120 nH 60 50 270 nH 40 30 100 nH 100 39 nH 15 nH 10 3.3 nH 20 10 0 1 10 100 1000 10,000 B overall H C Pick and place material F G A I J F E terminal A B max max I D Recommended Land Pattern Terminal wraparound: approx 0.015/0,38 both ends C max D ref E F G H 10 100 1000 Frequency (MHz) Frequency (MHz) IJ 0.0900.068 0.060 0.020 0.050 0.020 0.0400.0700.0400.030inches 2,291,73 1,52 0,51 1,27 0,51 1,021,781,020,76 mm Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm. Designer’s Kit C303 contains 10 of each 5% part Designer’s Kit C303-2 contains 10 of each 2% part Core material Ceramic Environmental RoHS compliant, halogen free Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 10.2 – 11.6 mg Ambient temperature –40°C to +125°C with Irms current Maximum part temperature +140°C (ambient + temp rise). Storage temperature Component: –40°C to +140°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +100 to +250 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000/7″ reel; 7500/13″ reel. Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.65 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Document 100-2 Revised 10/12/15