0805USB

Document 306-1
USB 2.0 Common Mode Choke 0805
Eliminates virtually all common mode noise in high-speed, differential mode signal transmission applications such as USB 2.0,
IEEE1394, HDMI and LVDS. Most provide >25 dB common
mode attenuation and >100 ohms impedance.
Designer’s Kit C384 contains 10 each of all 0603USB, 0805USB
and 1206USB parts
Core material Ferrite
Environmental RoHS compliant, halogen free
Terminations Gold over nickel over silver-palladium-glass frit.
Ambient temperature –40°C to +85°C with Irms current
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part number1
Common mode
impedance typ (Ohms)
10 MHz 100 MHz 500 MHz
0805USB-421ML_
0805USB-901ML_
0805USB-172ML_
0805USB-262ML_
0805USB-372ML_
0805USB-502ML_
0805USB-672ML_
0805USB-902ML_
14
28
57
85
118
148
246
294
42 70
90 154
170 303
260 435
370 641
500 945
670 1231
900 1715
Common mode
Inductance2 DCR max3 Isolation Irms4
attenuation typ (dB)
10 MHz 100 MHz 500 MHz min (nH)
(Ohms)
(Vrms) (mA)
1.1 2.3 8.4
1.4 4.2 16.9
2.3 6.7 22.0
3.0 8.6 27.8
4.511.9 34.3
4.914.5 31.3
8.416.6 30.0
8.718.7 30.5
1.When ordering, please specify packaging code:
0805USB-902MLC
Packaging:C=7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic tape (7500 parts per full reel).
2. Inductance measured at 100 MHz using an Agilent/HP 4286A
impedance analyzer and a Coilcraft SMD-A fixture.
3.DCR is specified per winding.
4.Current per winding that causes a 20°C rise from 25°C ambient.
5. Operating temperature range −40°C to 85°C.
6.Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
23
47
84
147
189
273
322
413
0.080 ±0.004
2,03 ±0,10
0.12
0.17
0.25
0.26
0.32
0.37
0.45
0.65
250500
250500
250500
250500
250500
250500
250500
250400
1
2
4
3
0.065 max
1,65
0.020 0.040
0,51 1,02
1
0.004
0,10
0.030
0,76
0.018
0,46
0.036
0,91
2
1
3
4
0.014
0,36
2
0.050 ±0.004
1,27 ±0,10
4
Dimensions are in
3
inches
mm
Recommended
Land Pattern
0.020
0,51
Weight 14.9 – 15.2 mg
Packaging 2000/7″ reel; 7500/13″ reel; Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.5 mm pocket depth
Document 306-1 Revised 01/18/12
Document 306-2
USB 2.0 Common Mode Filter — 0805
Typical Differential Mode Attenuation (Ref: 50 Ohms)
0
1
Attenuation (dB)
2
3
-421
-901
-172
-262
-372
-502
-672
-902
4
5
6
7
8
1
10
100
1000
10,000
Frequency (MHz)
Typical Common Mode Attenuation (Ref: 50 Ohms)
0
-421
-901
-172
-262
-372
-502
-672
-902
5
Attenuation (dB)
10
15
20
25
30
35
40
1
10
100
1000
10,000
Frequency (MHz)
Typical Impedance vs Frequency
Impedance (Ohms)
10000
-902
-672
-502
-372
-262
-172
-901
-421
1000
100
10
1
1
10
100
1000
10,000
Frequency (MHz)
Document 306-2 Revised 04/03/13