Document 1270-1 Low Profile USB Common Mode Choke 0805 •For noise suppression in super high speed signal lines: USB 3.x, HDMI 2.0, HDBaseT™, DisplayPort, DVI, etc.; and in high speed differential signal lines: USB 2.0, IEEE1394, LVDS, etc. •Suitable for USB-type C specification 1.0 •Up to 6 GHz differential mode 3 dB cutoff frequency; up to 30 dB common mode noise attenuation in GHz range Core material Ferrite Environmental RoHS compliant Terminations Matte tin over nickel over silver-platinum-glass frit. Weight 14.7 – 15.5 mg Ambient temperature –40°C to +125°C with Irms current. Maximum part temperature 140°C Storage temperature Component: –40°C to +140°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 2000/7″ reel; 7500/13″ reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.295 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Part number1 0805USBF-421MR_ 0805USBF-901MR_ 0805USBF-172MR_ 0805USBF-262MR_ 0805USBF-372MR_ 0805USBF-502MR_ 0805USBF-672MR_ 0805USBF-902MR_ Common mode impedance typ (Ohms) 10 MHz 100 MHz 500 MHz 1040 65 25 95140 35165 255 55250 400 105400 580 145545 800 160 6701090 200 9001400 Common mode Inductance2 DCR max3 Isolation Irms4 attenuation typ (dB) 10 MHz 100 MHz 500 MHz min (nH) (Ohms) (Vrms) (mA) 0.5 4.6 6.9 2.1 9.1 11.8 4.012.8 15.7 5.715.4 18.5 5.818.1 22.3 11.221.6 25.2 11.323.3 27.7 12.625.4 30.0 1.When ordering, please specify packaging code: 0805USBF-902MRC Packaging:C=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape (7500 parts per full reel). 2. Inductance measured at 100 MHz using an Agilent/HP 4286A impedance analyzer and a Coilcraft SMD-A fixture. 3.DCR is specified per winding. 4.Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 5.Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 28 60 101 165 241 315 434 560 0.080 ±0.004 2,03 ±0,10 0.11 0.14 0.22 0.235 0.27 0.32 0.37 0.63 250500 250500 250500 250500 250500 250500 250450 250350 1 2 4 3 0.055 max 1,40 0.004 0,10 0.020 0.040 0,51 1,02 1 0.030 0,76 0.018 0,46 0.036 0,91 2 1 3 4 0.014 0,36 2 0.050 ±0.004 1,27 ±0,10 4 Dimensions are in 3 inches mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Recommended Land Pattern 0.020 0,51 Document 1270-1 Revised 03/31/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 1270-2 USB 2.0, 3.x Common Mode Filter — 0805USBF Typical Differential Mode Attenuation (Ref: 50 Ohms) 0 1 Attenuation (dB) 2 3 4 -421 -901 -172 -262 -372 -502 -672 -902 5 6 7 8 1 10 100 1000 10,000 Frequency (MHz) Typical Common Mode Attenuation (Ref: 50 Ohms) 0 5 Attenuation (dB) 10 15 -421 -901 -172 -262 -372 -502 -672 -902 20 25 30 35 1 10 100 1000 10,000 Frequency (MHz) Typical Impedance vs Frequency Impedance (Ohms) 10000 -902 -672 -502 -372 -262 -172 -901 -421 1000 100 10 1 1 10 100 1000 10,000 Frequency (MHz) US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 1270-2 Revised 03/31/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.