LPS5030

Document 581-1
Shielded Power Inductors – LPS5030
• Very low DCR; excellent current handling
• 4.9 × 4.9 mm footprint; less than 3 mm tall
Designer’s Kit C420 contains 3 each of all values
Core material Ferrite
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight 226 – 244 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide,
0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5 Irms (A)6
DCR SRF
Inductance2 max3 typ4 10% 20% 30% 20°C40°C
Part number1 ±20% (µH) (Ohms)(MHz) drop drop drop rise rise
LPS5030-901MR_ 0.90 0.040
2503.84.04.12.10
2.80
LPS5030-122MR_ 1.2 0.043
2103.53.63.72.00
2.65
LPS5030-172MR_ 1.7 0.051
1903.03.23.31.90
2.50
LPS5030-222MR_ 2.2 0.057
1682.93.13.21.60
2.15
LPS5030-332MR_ 3.3 0.066
1252.32.52.61.40
1.80
LPS5030-472MR_ 4.7 0.083841.92.02.01.30
1.75
LPS5030-562MR_ 5.6 0.089701.81.81.91.25
1.65
LPS5030-682MR_ 6.8 0.099561.61.71.71.20
1.60
LPS5030-822MR_ 8.2 0.125451.61.71.71.10
1.55
LPS5030-103MR_10.0 0.127301.41.41.41.00
1.50
LPS5030-123MR_12.0 0.155241.31.41.40.95
1.40
LPS5030-153MR_ 15.0 0.160 32 0.800.900.900.921.40
LPS5030-183MR_ 18.0 0.170 27 0.800.820.870.901.30
LPS5030-223MR_ 22.0 0.190 24 0.700.750.780.881.25
LPS5030-333MR_ 33.0 0.260 19 0.600.630.640.851.20
LPS5030-473MR_ 47.0 0.330 16 0.500.530.550.751.00
LPS5030-683MR_ 68.0 0.440 12 0.400.430.440.650.900
LPS5030-823MR_ 82.0 0.470 11 0.380.400.400.600.830
LPS5030-104MR_100
0.600 10 0.270.310.320.550.750
LPS5030-124MR_120
0.800 9 0.260.290.300.450.660
LPS5030-154MR_150
0.860 7.50.220.250.263
0.420.570
LPS5030-224MR_ 220
1.35
6.0 0.21 0.2350.2450.36 0.500
LPS5030-334MR_ 330
1.80
5.0 0.1550.1550.2000.32 0.420
LPS5030-474MR_ 470
2.80
4.0 0.1170.1340.1460.28 0.370
LPS5030-564MR_ 560
3.20
3.6 0.1100.1300.1400.23 0.320
LPS5030-684MR_ 680
3.80
3.0 0.1000.1200.1260.20 0.290
LPS5030-105MR_1000
5.10
2.5 0.1000.1100.1100.18 0.250
LPS5030-155MR_1500
7.60
2.0 0.0680.0800.0890.15 0.210
LPS5030-185MR_1800
10.0
1.8 0.0690.0810.0860.13 0.170
LPS5030-225MR_2200
11.0
1.6 0.0630.0740.0800.10 0.150
LPS5030-335MR_3300
19.5
1.3 0.0560.0630.0670.0900.125
LPS5030-475MR_4700
26.0
1.1 0.0490.0560.0590.0800.110
1. Please specify termination and packaging codes:
LPS5030-105MRC
Termination:R=RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481
embossed plastic tape (750 parts
per full reel).
B=Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D
=13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (2500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an
Agilent/HP 4192A impedance analyzer or equivalent.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from
25°C ambient. This information is for reference only and
does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Document 581-1 Revised 09/02/15
Document 581-2
Shielded Power Inductors – LPS5030 Series
Typical L vs Frequency
Typical L vs Current
10000
10000
3300 µH
3300 µH
1000 µH
330 µH
100 µH
100
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
33 µH
10 µH
10
330 µH
100 µH
100
33 µH
10 µH
10
3.3 µH
3.3 µH
1
0.01
1
0.1
10
Frequency (MHz)
0.1
Current (A)
1
10
NOTE NEW PART ORIENTATION Parts are rotated 90° in the
packaging tape compared to previous versions of this product.
0.189 ±0.003*
4,80 ±0,076
Winding
direction
NEW
0.114 ±0.004 *
2,9 ±0,1
OLD
123
Internal
code
123
123
Dash
number
0.01
Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide,
0.32 mm thick, 8 mm pocket spacing, 3.1 mm pocket depth
0.189 ±0.003*
4,80 ±0,076
XXX X
1
123
123
123
Recommended
Land Pattern
0.060
1,50
0.134
3,40
0.039 typ
1,00
0.217
5,51
0.0665
1,689
0.039 typ
1,00
are of the case not including
* Dimensions
the termination. For maximum overall
dimensions including the termination, add
0.005 in / 0,13 mm.
For optional tin-lead and tin-silver-copper
terminations, dimensions are for the
mounted part. Dimensions before mounting
can be an additional 0.005 inch / 0,13 mm).
0.134
3,40
0.134
3,40
0.060
1,52
0.134
3,40
0.217
5,51
Dimensions are in
inches
mm
Document 581-2 Revised 09/02/15