LPS5010

Document 536-1
Shielded Power Inductors – LPS5010
• Very low DCR; excellent current handling
• 5.0 × 5.0 mm footprint; less than 1.0 mm tall
Designer’s Kit C407 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental RoHS compliant, halogen free
Terminations RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight 70 – 75 mg
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3000/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5 Irms (A)6
DCR SRF
Inductance2 max3 typ4 10% 20% 30% 20°C40°C
Part number1 ±20% (µH) (Ohms)(MHz) drop drop drop rise rise
LPS5010-471MR_
LPS5010-821MR_
LPS5010-152MR_
LPS5010-222MR_
LPS5010-332MR_
0.47 0.038
2903.13.33.42.02.7
0.82 0.058
1952.32.52.61.21.5
1.5 0.072
1681.71.81.90.90
1.4
2.2 0.100
1441.41.51.60.88
1.2
3.3 0.125
1051.11.21.30.86
1.1
LPS5010-472MR_ 4.7
LPS5010-562MR_ 5.6
LPS5010-682MR_ 6.8
LPS5010-103MR_ 10
LPS5010-153MR_ 15
0.175760.95
1.11.10.85
0.98
0.240 75 0.900.971.000.750.92
0.255 71 0.820.900.930.740.85
0.350 51 0.660.720.740.730.80
0.500 39 0.550.590.620.680.75
LPS5010-223MR_ 22
LPS5010-333MR_ 33
LPS5010-473MR_ 47
LPS5010-683MR_ 68
LPS5010-104MR_100
0.670
1.05
1.45
2.00
3.10
32 0.470.510.530.460.62
26 0.380.420.430.400.55
20 0.310.340.360.330.44
15 0.260.290.300.250.35
12 0.210.230.240.210.28
LPS5010-124MR_120
LPS5010-154MR_150
LPS5010-224MR_220
LPS5010-334MR_330
LPS5010-474MR_470
3.50
4.25
6.25
8.60
12.7
11 0.200.220.230.190.25
9.0
0.180.200.210.170.23
7.0
0.150.160.170.150.20
5.5
0.120.130.140.130.185
4.5
0.090
0.110.110.110.150
LPS5010-564MR_560
LPS5010-684MR_ 680
15.7
20.0
4.0
0.090
0.100.100.100.135
3.70.0900.0970.10 0.0900.125
1. Please specify termination and packaging codes:
LPS5010-684MRC
Termination:R=RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B=Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D
=13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same for
parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified inductance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from
25°C ambient. This information is for reference only and
does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 536-1 Revised 09/02/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 536-2
Shielded SMT Power Inductors – LPS5010 Series
Typical L vs Current
Typical L vs Frequency
10000
10000
1000 µH
100
100 µH
10
10 µH
1
0.1
0.1
Current (A)
1
10
0.189 ±0.003*
4,80 ±0,076
XXX X
0.82 µH
0.1
0.01
1
0.1
10
Frequency (MHz)
Packaging 1000/7″ reel; 3000/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
NOTE NEW PART ORIENTATION Parts are rotated 90° in the
packaging tape compared to previous versions of this product.
0.189 ±0.003*
4,80 ±0,076
Winding
direction
NEW
0.217
5,51
123
123
0.134
3,40
0.0665
1,689
0.039 typ
1,00
are of the case not including
* Dimensions
the termination. For maximum overall
123
Recommended
Land Pattern
0.0354 ±0.004 *
0,90 ±0,10
0.039 typ
1,00
OLD
123
Internal
code
123
0.060
1,52
10 µH
10
123
Dash
number
100 µH
100
1
0.82 µH
0.01
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
dimensions including the termination, add
0.005 in / 0,13 mm.
For optional tin-lead and tin-silver-copper
terminations, dimensions are for the
mounted part. Dimensions before mounting
can be an additional 0.005 inch / 0,13 mm).
0.134
3,40
0.134
3,40
0.060
1,52
0.134
3,40
0.217
5,51
Dimensions are in
inches
mm
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 536-2 Revised 09/02/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.