SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Series - DO-214 Pb e3 RoHS Description Fixed Voltage Series DO-214 are uni-directional SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single line protection using a fixed voltage switching device for negative surges. All positive surges are routed through an internal diode to a ground reference. Features and Benefits Agency Approvals • RoHS compliant, leadfree, and halogen-free surged in excess of ratings • Low voltage overshoot • Integrated diode for positive voltage surges • Low on-state voltage Agency Agency File Number • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD609A.01) • Does not degrade surge capability after multiple surge events within limit. E133083 Pinout Designation • Fails short circuit when Applicable Global Standards Indicates cathode Schematic Symbol (T/R) • TIA-968-A • GR 1089 Intra-building* • TIA-968-B • IEC 61000-4-5 2nd edition • ITU K.20/21 Enhanced Level (G) • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 993 • GR 1089 Inter-building* • YD/T 950 *A-rated parts require series resistance Electrical Characteristics Part Number P0641SALRP P0721SALRP P0901SALRP P1101SALRP P1301SALRP P1701SALRP P0641SCLRP P0721SCLRP P0901SCLRP P1101SCLRP P1201SCLRP P1301SCLRP P1701SCLRP P1101SDLRP P1301SDLRP Marking P61A P71A P91A P01A P131A P17A P61C P71C P91C P01C P121C P131C P17C P01D P131D VDRM @lDRM=5µA VS @100V/µs IH IS IT VT @IT=2.2 Amps VF V min V max mA min mA max A max V max V max 58 65 75 95 120 160 58 65 75 95 105 120 160 95 120 77 88 98 130 160 200 77 88 98 130 140 160 200 130 160 120 120 120 120 120 120 120 120 120 120 120 120 120 120 120 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are not appropriate for positive ringing systems. Capacitance @1MHz, -2V bias pF pF min pF max 50 45 45 40 40 30 65 60 60 50 50 50 40 50 50 90 85 80 70 70 55 200 190 180 160 160 160 130 160 160 © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 SIDACtor ® Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 0.2/310 0.5/700 2 2/10 2/10 / 8/20 1.2/50 2 10/160 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 1 1 1 1 A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 D — 1000 800 — — — — 200 350 50 1000 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that remains in thermal equilibrium. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Parameter Value Unit DO-214AA TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W V-I Characteristics +I VS VDRM VF VT -V IDRM +V IH IS IT IPP – Peak Pulse Current – %IPP tr x td Pulse Waveform 50 Half Value 0 0 td tr t – Time (µs) Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 2 IH (TC = 25ºC) 2.0 14 12 Ratio of Percent of VS Change – % tr = rise time to peak value td = decay time to half value Waveform = tr x td -I Normalized VS Change vs. Junction Temperature Peak Value 100 0 -4 -6 1.8 1.6 1.4 1.0 0.8 0.6 0.4 -8 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 25°C 1.2 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC SIDACtor ® Protection Thyristors SLIC Protection Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material TL TS(max) tL Ramp-down Preheat TS(min) tS Time Environmental Specifications Additional Information Resources Critical Zone TL to TP Ramp-up time to peak temperature (t 25ºC to peak) UL recognized epoxy meeting flammability classification V-0 Datasheet tP 25 Physical Specifications Lead Material Figure 1 TP Temperature Reflow Condition Samples High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity 85%RH, +85°C, 168 hrs., 3 reflow cycles JEDEC-J-STD-020, Level 1 LevelPM for pg. 94(+260°C DO-214 FixedPeak). Voltage Series.eps Part Numbering Part Marking Cathode Indicator P xxx 1 S X L RP DEVICE TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE REEL PACK L: RoHS COMPLIANT IPP RATING XXXXX XXXXX Part number code (refer to Electrical Characteristics table) Date code PACKAGE TYPE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — DO-214AA Case Temperature Measurement Point Cathode Indicator B D Dimensions C A H E F K G 0.079 (2.0) Millimeters Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 Dimensions are in inches (and millimeters). 0.110 (2.8) 0.079 (2.0) Inches Pad Outline (MM) Packing Options Package Type S Description Quantity Added Suffix Industry Standard DO-214AA Tape & Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — DO-214AA 0.157 (4.0) 0.472 (12.0) Cathode 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. 0.49 (12.4) © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/16/16 Cover tape Dimensions are in inches (and millimeters). Direction of Feed