P9 www.vishay.com Vishay Sfernice 9 mm Multi-Ganged Potentiometer FEATURES • Conductive plastic element • Ultra compact (extra miniature module size) • Multiple assemblies (up to seven modules) • Shaft and panel sealed option • Center mechanical detent fully integrated in option • Center tap option • Custom designs available on request • Test according to CECC 41000 or IEC 60393-1 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02") 9.5 (0.37) L: See Shaft table 3.6 (0.14) 2.5 (0.10) 2.5 (0.10) M7 x 0.75 11.35 (0.45) 1 (0.04) P9 6.4 (0.25) 3 3.5 (0.14) 2.5 (0.10) 7 (0.276) 2.5 (0.10) 5 (0.20) Vertical Mounting See Shaft table 0.9 (0.04) 2.5 (0.10) 0.45 R (0.02) Center Tap 3.45 (0.14) 2 (0.08) 3.8 (0.15) 7.5 (0.30) 5.6 (0.22) 4.7 (0.19) See Bushing table 2.5 (0.10) 3.5 (0.14) 3x 0.9 2.5 (0.04) (0.10) 2.5 (0.10) 0.2 (0.01) 2.5 (0.10) 2.5 (0.10) 2.5 (0.10) Center Tap and Vertical Mounting 7.5 (0.30) Revision: 24-Sep-15 2.5 (0.10) 7.9 (0.31) Document Number: 51047 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice GENERAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Resistive element Conductive plastic Electrical travel 270° ± 10° RATED POWER (W) Linear Taper Power rating chart 0.1 Non Linear Taper 0.05 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) a c (1) Circuit diagram (3) cw b (2) 90 % F S R Vs % 50 % Ve A W Taper 20 % L 10 % 50 % 15° Electrical travel 270° 15° Mechanical travel 300° Resistance range Tolerance Power rating at 70 °C Linear taper Non-linear taper Standard On request 1 k to 1 M 2.2 k to 500 k 20 % 10 % Linear Taper 0.1 W Non-Linear Taper 0.05 W Multiple assemblies linear taper 0.05 W per module Multiple assemblies non-linear taper 0.025 W per module Temperature coefficient (typical) ± 500 ppm 10 VDC 50 VAC Limiting element voltage 3 End resistance (typical) Contact resistance variation Linear law (typical) 2 % of nominal resistance Independent linearity Linear law (typical) ±5% Insulation resistance Dielectric strength Attenuation (typical) Revision: 24-Sep-15 100 M at 250 VDC 300 VAC during 1 min 90 dB max./0.05 dB min. Document Number: 51047 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice MECHANICAL SPECIFICATIONS Mechanical endurance 25 000 cycles min. Mechanical travel 300° ± 5 Operating torque 0.2 Ncm to 1.5 Ncm (0.3 oz.-inch to 1.8 oz.-inch) End stop torque 50 Ncm max. (4.4 lb-inch max.) Shaft push/pull force 7 DaNcm max. (15.7 lbf max.) Weight (one module) 6.25 g (without nut and washer) (0.22 oz.) Note • Nothing stated herein shall be construed as a guarantee of quality or durability. ENVIRONMENTAL SPECIFICATIONS Temperature range -55 °C to +100 °C Climatic category 55/100/21 Sealing IP 64 MARKING PACKAGING • • • • • Box of 25 pieces • Box of 100 pieces Code for tolerance Code for ohmic value Taper Code for date code PERFROMANCES TYPICAL VALUE AND DRIFTS TESTS CONDITIONS RT/RT (%) R1-2/R1-2 (%) OTHER 1000 h at rated power 90'/30' - ambient temp. 70 °C ±5% ± 10 % Contact resistance variation < 5 % Rn Damp heat, steady state 21 days at 40 °C ± 2 °C and 90 % to 95 % relative humidity ±5% - Insulation resistance > 10 M Change of temperature Ambient temperature -55 °C to +100 °C 5 cycles ± 0.5 % - - Mechanical endurance 25 000 cycles at rated power 90 % of electrical travel 16 cycles per minute Temperature: 20 °C ±6% - Contact resistance variation ± 12 % 50 g’s, 11 ms 3 shocks - 3 directions ± 0.2 % ± 0.5 % - 10 Hz to 55 Hz 0.75 mm or 10 g’s 6h ± 0.2 % - V1-2/V1-3 ± 0.5 % Electrical endurance Shock Vibration Revision: 24-Sep-15 Document Number: 51047 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice ORDERING INFORMATION (Part Number) P 9 MODEL NUMBER OF MODULES P9A 1 to 7 A 1 BUSHING R 1 LOCATING PEG 0 0 PANEL SEALED F I DETENT OPTION R X 1 1 0 PIN STYLE SHAFT 3 M A RESISTANCE CODE/ TOLERANCE CODE/ TAPER R = M7 x 0.75 mm to 7 mm X = M7 x 0.75 mm to 5 mm BUSHING X: Bushing R: Bushing • Nut tightening torque M7 bushing 120 Ncm max. (10.6 lb-inch max.) • Nut and washer are delivered in standard packaging 10 M7 x 0.75 M7 x 0.75 5 (0.20) 7 (0.28) 2 M7 x 0.75 0.7 Revision: 24-Sep-15 Document Number: 51047 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice ORDERING INFORMATION (Part Number) P MODEL 9 A NUMBER OF MODULES 1 R 1 0 LOCATING PEG BUSHING 0 F PANEL SEALED I DETENT OPTION 0 = without 0 = without 1 = with P = with 0= without M = center detent LOCATING PEG R X 1 1 0 3 A RESISTANCE CODE/ TOLERANCE CODE/ TAPER PIN STYLE SHAFT M See code below PANEL SEALED 2 (0.08) 0.8 (0.03) • Only for R and X bushing without locating peg 0.8 (0.03) • Front mounting surface with panel sealed option is: 6.2 mm ± 0.5 mm length for R bushing and 4.2 mm ± 0.5 mm length for X bushing 5.6 (0.22) • The ring is delivered with nut and washer ADVISED PANEL CUT OUT (including peg option) 6 (0.24) Ø 6.9 (0.27) • The seal should be placed between panel and body. Sealing is obtained by tightening the seal against the panel when mounting the potentiometer Tightening torque 50 Ncm up to 100 Ncm • Advised panel hole dimensions: Ø 2.2 (0.09) Ø 6.9 (0.27) Ø 6.9 (0.27) DETENT OPTION • Stable position and in Mid mechanical travel • Rotational life: 10 000 actuations 2.35 4.7 (0.09) (0.19) Only for shaft diam. 3.5 For shaft diam. 3.5 or 6 Full CW Full CCW SHAFT DIAMETER - FMS - STYLE L (mm) 15 Style Round Slotted Flat Ø 3.5 DFR DFS DFF Ø6 FFR FFS FFF Note (1) For X bushing (16 mm) Round Knurled FGK (1) 20 Slotted DIS FIS Round DIR FIR Slotted Flat DIF FIF Round DLR FLR 25 Slotted DLS FLS Flat DMF FMF 6 (0.236) 5 (0.197) P1 P2 L 0.5 (0.020) 20° L P1 P2 Revision: 24-Sep-15 1 (0.039) Ø 1.6 (0.06) 30 Slotted DMS FMS Knurled For D diameter: Ø 4.7 mm For F diameter: Ø 6 mm 0.5 (0.020) Round DMR FMR Flat Ø 1 (0.039) Flat DLF FLF Ø 3.5 mm = 2.5 mm Ø 6 mm = 4.5 mm L = 15 mm 7 mm L > 15 mm 12 mm 18 teeth 90° Document Number: 51047 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice ORDERING INFORMATION (Part Number) P MODEL 9 A NUMBER OF MODULES 1 R 1 0 LOCATING PEG BUSHING 0 PANEL SEALED F I DETENT OPTION R X 1 1 0 M A RESISTANCE CODE/ TOLERANCE CODE/ TAPER PIN STYLE SHAFT 3 See Pin table First digit: pin type X, J, S, Z, P, L W or N Second digit: pin configuration 1, 2, 3, 4 or N PIN STYLE - HORIZONTAL MOUNTING PIN TYPE 3.5 (0.14) X PC mount J PC mount center tap S Soldering style Z Center tap soldering style L Long pin P Center tap with long pin NN If different types of pin style in the same potentiometer 3.5 (0.14) 11.5 (0.45) PIN CONFIGURATION 1 7 x 2.5 (0.098) 2 2.5 (0.098) 2.5 (0.098) 2.5 (0.098) 2.5 mm between gang Revision: 24-Sep-15 7 x 2.5 (0.098) 3 2.5 (0.098) 7 x 2.5 (0.098) 2.5 (0.098) 2.5 (0.098) 2.5 (0.098) 2.5 mm - 5 mm - 2.5 mm between gang 2.5 (0.098) 2.5 (0.098) 5 mm between gang Document Number: 51047 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice ORDERING INFORMATION (Part Number) P MODEL 9 NUMBER OF MODULES A 1 BUSHING R 1 0 LOCATING PEG 0 PANEL SEALED F I DETENT OPTION R X 1 1 0 M A RESISTANCE CODE/ TOLERANCE CODE/ TAPER PIN STYLE SHAFT 3 See Pin table First digit: pin type X, J, S, Z, P, L W or N Second digit: pin configuration 1, 2, 3, 4 or N PIN STYLE - VERTICAL MOUNTING W1 Single gang vertical mounting 4.7 (0.19) W2 Dual gang vertical mounting 7.5 (0.3) W3 W4 Single gang with center tap vertical mounting 3.8 10.8 (0.15) (0.43) 2.5 (0.098) 7.5 (0.3) 2.5 (0.098) W1 - W3 2.5 (0.098) 2.5 (0.098) W2 - W4 Dual gang with center tap vertical mounting Revision: 24-Sep-15 Document Number: 51047 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 P9 www.vishay.com Vishay Sfernice ORDERING INFORMATION (part number) P MODEL 9 A NUMBER OF MODULES 1 R 1 0 LOCATING PEG BUSHING 0 F PANEL SEALED I DETENT OPTION R X 1 1 0 M A RESISTANCE CODE/ TOLERANCE CODE/ TAPER PIN STYLE SHAFT 3 Resistance code: 102 = 1 k to 105 = 1 M Tolerance code: standard: M = ± 20 % on request: K = ± 10 % taper: A, L, W, F, S, R or special code given by Vishay SPECIAL CODES GIVEN BY VISHAY • • • • • Custom shaft Design on request Specific linearity Specific interlinearity Specific variation law PART NUMBER DESCRIPTION (for information only) P9A 1 R MODEL MODULES BUSHING 1 0 0 FI R X1 10K 20 % A e3 LEAD LOCATING SEALING DETENT SHAFT SHAFT LEADS VALUE TOL. TAPER SPECIAL SPECIAL (Pb)PEG OPTIONS OPTIONS FREE RELATED DOCUMENTS APPLICATION NOTES Potentiometers and Trimmers www.vishay.com/doc?51001 Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029 Revision: 24-Sep-15 Document Number: 51047 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000