P34TG-xxxxE/Z5:1M Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] PMRW-SERIES Rev.07-2015 8 Watt 5:1 Wide Input Single and Dual Reg. Output 3 kV DC I/O Isolation DIP24 case On/Off Control Designed for Railway App. The PMRW Series include high performance 8W single & dual output DCDC converters. These converters are consisted with nickle-coated copper DIP24 package with high performance features like synchronous rectification, high efficiency and tight line / load regulation. The Devices are encapsulated flame retardant resin. Available with railway Input voltages of 24, 36, 48, 72, 96 and 110Vdc (5:1 ultra wide), output voltages 3.3 , 5 , 12 , 15 , ±5, ±12 , ±15 (±1%) and high efficiency operation up to 86% All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ Start up time (Nominal Vin and constant resistive load) Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (0% - 100%) Cross Regulation (Dual Output) 2 Ripple and Noise (20Mhz bandwidth) 3 Temperature Coefficient Transient Recovery Time4 Transient Response Deviation4 5:1 Wide Input (see table) Pi Type 20 mA pk-pk, typ. 30mS, typ. ± 1% Indefinite (hiccup) (Automatic Recovery) ± 0.5%, max. ± 0.5%, max. ± 5% 75 mV pk-pk ± 0.02% / °C 250us, typ. ± 3%, max. ± 5%, max (for 3.3V output) General Specifications I/O Isolation Voltage (60 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) Designed to meet: Safety Standart Thermal Shock Shock/Vibration 3000 VDC 1000 pF, typ. 1000 MOhm 220-330 kHz, typ. 95% rel H > 800 Khrs IEC/EN 60950-1; EN50155 IEC60068 EN 61373 Physical Specifications Case Material Potting Material Weight Nickel-coated Copper Epoxy (UL94V-0 rated) ~ 18g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 105°C -55 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMRW-Series – P34TG-xxxxE/Z5:1M – Single / Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Single and Dual Output ) ) ) mA (mA A) mA d m ( a ( ad ( d o ) d o a L a L C ) o . ll L D F) 5 n C Lo t Mi t Fu d (u (VD No Full e (V n n ) a g t t e e e o n n a r r % g t rre rre lta or L Vol Cur Cur cy ( t Vo t Cu put Cu acit put put put cien Inpu Inpu In Out Out Out Effi Cap Order # SINGLE OUTPUT P34TG-243R3E5:1M P34TG-2405E5:1M P34TG-2412E5:1M P34TG-2415E5:1M P34TG-1103R3E5:1M P34TG-11005E5:1M P34TG-11012E5:1M P34TG-11015E5:1M 13-70 13-70 13-70 13-70 42-176 42-176 42-176 42-176 30 20 10 10 10 10 5 5 398 387 392 389 89 87 87 88 3.3 5 12 15 3.3 5 12 15 0 0 0 0 0 0 0 0 2400 1600 665 535 2400 1600 665 535 83 86 85 86 81 84 84 83 1330 1330 330 220 1330 1330 330 220 DUAL OUTPUT P34TG-2405Z5:1M P34TG-2412Z5:1M P34TG-2415Z5:1M P34TG-11005Z5:1M P34TG-11012Z5:1M P34TG-11015Z5:1M 13-70 13-70 13-70 42-176 42-176 42-176 10 10 10 10 5 5 402 395 386 91 90 88 ±5 ± 12 ± 15 ±5 ± 12 ± 15 0 0 0 0 0 0 ± 800 ± 335 ± 265 ± 800 ± 335 ± 265 83 85 86 80 82 83 ± 900 ± 220 ± 100 ± 900 ± 220 ± 100 If you need other specifications, please enquire. PMRW-Series – P34TG-xxxxE/Z5:1M – Single / Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 Package / Pinning / Derating 25.40 (1.00) 2 3 9 15.24 (0.60) 1 All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Standard Drawing For exact pinning please see connection table! Specification may change without notice. 11 Bottom View 23 22 16 14 2.54 (0.10) DIP24 – METAL CASE 5.08 (0.20) 10.20 (0.40) PEAK 20.30 (0.80) Modelcode Datecode 31.80 (1.25) 3.00 (0.12) OUTPUT POWER TEMPERATURE DERATING GRAPH 100% 75% 50% 25% -20% 70 -40 -20 0 20 40 60 85 80 100 AMBIENT TEMPERATURE (°C) # 1 2 3 9 11 14 16 22 23 PIN CONNECTIONS SINGLE DUAL CTRL CTRL - Vin - Vin - Vin - Vin Omitted Common N.C. - Vout +Vout +Vout - Vout Common +Vin +Vin +Vin +Vin App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH and source capacitor Cin (33uF, ESR<1Ohm at 100KHz) 2 = One load is 25% to 100%, the other load is 100% load, the output voltage variable is within ±5% 3 = Measured with a 0.1uF ceramic capacitor an 10uF electrolytic capacitor 4 = Tested by normal Vin and 75%-50%-25% load step change at 1A/us 5 = Tested by minimal Vin and constant resistive load Operation at no-load conditions will not damage these devices, however they may not meet all specifications. PMRW-Series – P34TG-xxxxE/Z5:1M – Single / Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 App Notes EMI Filter (For 110Vin Models only) Input Filter components (C1, C2, C3 = 1uF, 250V) are used to meet conducted emissions 79BuV from 0.15-0.5MHz and 73BuV from 0.530MHz. The components should be mounted as close as possible. EMC Specifications Radiated Emissions EN50121-3-2 Conducted Emissions EN50121-3-2 Class A ESD EN50121-3-2 RS EFT Surge CS PFMF EN50121-3-2 EN50121-3-2 EN50121-3-2 EN50121-3-2 EN61000-4-8 Air ± 8KV Contact ± 6KV 20V/m 2.0 KV 2.0 KV 10V 10A/m 40dBuV from 30-230MHz 47dBuV from 230-1000MHz 99dBuV from 0.15-0.5MHz 93dBuV from 0.5-30MHz Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Over Voltage Protection Over Current Protection The module has an internal output over voltage protection circuit, which monitors the voltage on the output terminals. If this voltage exceeds the over voltage set point, the module will activate the control loop of internal circuit to clamp the output voltage. The module includes an internal over current protection circuit, which will endure current limiting for an unlimited duration during output over load condition. If the output current exceeds the OCP set point, the module will shut down automatically (hiccup). The module will try to restart after shut down. If the over load condition still exists, the module will shut down again. The Remote on/off control: Positive logic: Turns on the module during high logic and off during low logic. Ctrl module on/off can be controlles by an external switch between ctrl terminal and –Vin. The switch can be open collector or open drain. If the ctrl feature is not used, please leave the ctrl pin floating. PMRW-Series – P34TG-xxxxE/Z5:1M – Single / Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4