P34TG-xxxxE/Z2:1MLF PMD-SERIES Rev.11-2008 8 Watt Regulated Single and Dual Output 1.5 kV DC I/O Isolation DIP24 Metal Case Continuous Short Circuit Prot. Full SMD Technology Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMD 8W series P34TG-xxxxE/Z2:1MLF is a family of cost effective 8W single & dual output DC-DC converters. These converters are encapsulated in miniature DIP24 metal case. High performance features: 1500VDC input/output isolation, continuous short circuit protection with automatic restart and tight line / load regulation, high efficiency operation, output voltage accuracy of ±1% maximum and a wide input of 2:1 All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ 2:1 Wide Input Pi Type 35 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (Io = 10 - 100%) Cross Regulation³ (Dual Output) Over Current Protection Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 1% Indefinite (automatic recovery) ± 0.5% ± 0.5% (3.3 Vout Models: ± 0.7%) ± 5% 150% of FL, typ. 75 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC 1000 pF, typ. 1000 MOhm 330 kHz 95% rel H > 0.91 Mhrs Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 17.0g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +60°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMD-Series – P34TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output Order # ) A) ) mA A) d (m (mA ad (m ad ( a o ) o d L L a C ) o ll uF) n. (VD o Lo t Full L VDC d² ( t Mi t Fu ( e N a n n ) g t e o e e a n n r r % t rre rre y( ltag or L Vol Cur Cur acit t Vo t Cu put Cu ienc put put put Cap Inpu Inpu In Out Out Out Effic SINGLE OUTPUT P34TG-123R3E2:1MLF P34TG-1205E2:1MLF P34TG-1212E2:1MLF P34TG-1215E2:1MLF P34TG-243R3E2:1MLF P34TG-2405E2:1MLF P34TG-2412E2:1MLF P34TG-2415E2:1MLF P34TG-483R3E2:1MLF P34TG-4805E2:1MLF P34TG-4812E2:1MLF P34TG-4815E2:1MLF 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 20 20 20 20 15 15 15 15 15 15 15 15 687 762 784 803 344 381 392 397 172 191 198 198 3.3 5 12 15 3.3 5 12 15 3.3 5 12 15 0 0 0 0 0 0 0 0 0 0 0 0 2000 1500 665 535 2000 1500 665 535 2000 1500 665 535 80 82 85 83 80 82 85 84 80 82 84 84 3300 2200 470 220 3300 2200 470 220 3300 2200 470 220 DUAL OUTPUT P34TG-1205Z2:1MLF P34TG-1212Z2:1MLF P34TG-1215Z2:1MLF P34TG-2405Z2:1MLF P34TG-2412Z2:1MLF P34TG-2415Z2:1MLF P34TG-4805Z2:1MLF P34TG-4812Z2:1MLF P34TG-4815Z2:1MLF 9-18 9-18 9-18 18-36 18-36 18-36 36-72 36-72 36-72 20 20 20 15 15 15 15 15 15 813 794 794 407 402 392 203 196 196 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ±5 ± 12 ± 15 0 0 0 0 0 0 0 0 0 ± 800 ± 335 ± 265 ± 800 ± 335 ± 265 ± 800 ± 335 ± 265 82 84 84 82 83 85 82 85 85 ± 1000 ± 220 ± 100 ± 1000 ± 220 ± 100 ± 1000 ± 220 ± 100 If you need other specifications, please enquire. Notes: PMD-Series – P34TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating PIN CONNECTIONS # SINGLE DUAL 2 - Vin - Vin 3 - Vin - Vin 9 Omitted Common 11 N.C. - Vout 14 +Vout +Vout 16 - Vout Common 22 +Vin +Vin 23 +Vin +Vin others Omitted Omitted App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by nominal Vin and constant resistor load. ³ = One load is 25% - 100%, the other load is 100%, the output voltage variable rate is within ± 5% 4 = Input filter components (C1,C2,L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; all leads should be minimized to decrease radiated noise. 5 = An external filter capacitor (e.g. Nippon - chemi - con KY series, 220uF/100V) is required if the module has to meet EN61000-4-4 and EN61000-4-5. EMC SPECIFICATIONS Radiated Emissions EN 55022 4 Conducted Emissions EN55022 ESD IEC 61000-4-2 RS IEC 61000-4-3 5 EFT IEC 61000-4-4 5 Surge IEC 61000-4-5 CS IEC 61000-4-6 PFMF IEC 61000-4-8 PMD-Series – P34TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3 CLASS A CLASS A Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Perf. Criteria A