P6UG_2:1

P6UG-xxxxE/Z2:1LF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PMMB-SERIES
Rev.10-2013
1 Watt
2:1 Wide Input
Single and Dual Reg. Output
SIP6 Case
1.5 kV DC I/O Isolation
Low Ripple and Noise
The PMMB series P6UG-xxxxE/Z2:1LF is a family of cost effective 1 W
single and dual output DC/DC converters. These converters are consisted
with Non-conductive Black Plastic in a SIP6 package. Devices are
encapsulated. High performance features: 1500VDC input/output isolation,
high efficiency operation, output voltage accuracy of ±2% and low output
ripple and noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Surge Voltage (100mS)
2:1 Wide Input (see table)
Capacitors
05 Models
12 Models
24 Models
48 Models
15 VDC, max.
25 VDC, max.
50 VDC, max.
100 VDC, max.
Output Specifications
Voltage Accuracy
Output Current
Short Circuit Protection
Line Regulation
Load Regulation (0% - 100%)
Cross Regulation¹
Ripple and Noise (20Mhz bandwidth)²
Temperature Coefficient
Transient Recovery Time4
Transient Response Deviation4
± 2%
0 mA, min. (for max see table)
Continuous (Automatic Recovery)
± 0.2%, max.
± 1.0%, max.
± 5% (Dual Output)
50 mV pk-pk
± 0.02% / °C
1 mS
± 3%, max.
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
Safety Standard
See Table
1500 VDC
35 pF
1000 MOhm
150 - 550 kHz (Variable)
95% rel H
follows
Designed to meet IEC/EN 60950-1
PMMB-Series – P6UG-xxxxE/Z2:1LF – Single/Dual Output – SIP6 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Physical Specifications
Case Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
~ 3 g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
105°C
-55 to +125°C
Free Air Convection
Soldering 260°C, max. (1.5mm from case 10s.)
Selection Guide
Single / Dual Output
Order #
A)
)
)
mA ad (mA
d (m
(
a
)
o
d
³
C)
Loa
ull L
uF)
VDC
l l Lo
(VD
nt F
)
ad (
ge (
t No ent Fu
e
e
o
a
n
r
%
g
t
L
r
(
l
e
a
r
r
r
r
lt
or
Cu
Vo
cy
t Cu put Cu
t Vo
acit
put
put
cien
Inpu
Inpu
In
Out
Out
Effi
Cap
SINGLE OUTPUT
P6UG-0505E2:1LF
P6UG-0512E2:1LF
P6UG-0515E2:1LF
P6UG-0524E2:1LF
P6UG-1205E2:1LF
P6UG-1212E2:1LF
P6UG-1215E2:1LF
P6UG-1224E2:1LF
P6UG-2405E2:1LF
P6UG-2412E2:1LF
P6UG-2415E2:1LF
P6UG-2424E2:1LF
P6UG-4805E2:1LF
P6UG-4812E2:1LF
P6UG-4815E2:1LF
P6UG-4824E2:1LF
4.5-9
4.5-9
4.5-9
4.5-9
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
35
35
35
35
20
20
20
20
10
10
10
10
7
7
7
7
263
259
254
265
108
108
105
109
54
52
52
55
27
27
27
28
5
12
15
24
5
12
15
24
5
12
15
24
5
12
15
24
200
83
67
42
200
83
67
42
200
83
67
42
200
83
67
42
76
77
79
76
77
77
80
77
77
80
80
77
77
78
78
76
1680
820
680
470
1680
820
680
470
1680
820
680
470
1680
820
680
470
DUAL OUTPUT
P6UG-0512Z2:1LF
P6UG-0515Z2:1LF
P6UG-1212Z2:1LF
P6UG-1215Z2:1LF
P6UG-2412Z2:1LF
P6UG-2415Z2:1LF
P6UG-4812Z2:1LF
P6UG-4815Z2:1LF
4.5-9
4.5-9
9-18
9-18
18-36
18-36
36-72
36-72
35
35
20
20
10
10
7
7
259
254
108
105
52
52
27
27
± 12
±15
± 12
±15
± 12
±15
± 12
±15
± 42
± 33
± 42
± 33
± 42
± 33
± 42
± 33
77
79
77
80
80
80
78
78
±470
±330
±470
±330
±470
±330
±470
±330
If you need other specifications, please enquire.
PMMB-Series – P6UG-xxxxE/Z2:1LF – Single/Dual Output – SIP6 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
11.00
(0.43)
10.50
(0.41)
0.50
(0.02)
3.00
(0.12)
2.38
(0.09)
0.25
(0.01)
Package / Pinning / Derating
#
1
2
4
5
6
PIN CONNECTIONS
SINGLE
DUAL
- Vin
- Vin
+Vin
+Vin
+Vout
+Vout
Omitted
Common
- Vout
- Vout
App Notes:
1 = One load is 25% to 100%, the other load is 100%, the output voltage variable rate is within ± 5%.
2 = Measured with a 1uF ceramic capacitor.
3 = Tested by minimal Vin and constant resistive load.
4 = Tested by normal Vin and 25% load step change (75%-50%-25% of Io).
- Absolute Maximun ratings: Exceeting the absolute ratings of the unit could cause damage. It is not allowed for continuous
operating.
Output Ripple & Noise Measurement Test
Use a capacitor Cout (1.0 uF) measurement. The scope measurement bandwidth is 0-20 MHz.
PMMB-Series – P6UG-xxxxE/Z2:1LF – Single/Dual Output – SIP6 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3