P(C)26NG-xxxxE/Z2:1LF PMB-SERIES Rev.07-2015 6 Watt 2:1 Wide Input Single and Dual Reg. Output 1.5 kV DC I/O Isolation SIP8 case On/Off Control (optional) Contin. Short Circuit Protection Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMB series is a family of cost effective 6W single and dual output DC/DC converters with an optional control Pin. These converters are in an ultra-miniature SIP8 plastic case. Devices are encapsulated using flame retardant resin. High performance features include continuous / long time short circuit protection with automatic restart and tight line / load regulation. High performance features include high efficiency operation and output voltage accuracy of ±1% maximum. PMB-Series is a good substitution of traditional DC/DC converters 6W in DIP24 package. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ Start up time (Nominal Vin and constant resistive load) Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (0% - 100%) Cross Regulation (Dual Output) 2 Ripple and Noise (20Mhz bandwidth) Temperature Coefficient Transient Recovery Time4 Transient Response Deviation4 2:1 Wide Input (see table) Capacitors 30 mA pk-pk 30mS, typ. ± 1% Continuous (Automatic Recovery) ± 0.2%, max. ± 1%, max. ± 5% 75 mV pk-pk ± 0.02% / °C 500us, typ. ± 3%, max. ± 5%, max (at 3.3V & 5V output) 3 General Specifications I/O Isolation Voltage (60 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) 1500 VDC 50 pF, max. 1000 MOhm 100 kHz, min. 95% rel H > 770 Khrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic Epoxy (UL94V-0 rated) ~ 4.8g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +65°C (ambient) 105°C -55 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMB-Series – P(C)26NG-xxxxE/Z2:1LF – Single / Dual Output – SIP8 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Single and Dual Output ) ) ) mA (mA A) mA d m ( a ( ad ( d o ) d o a L a L C ) o . ll L F) 5 D n C Lo t Mi t Fu d (u (VD No Full e (V n n ) a g t t e e e o n n a r r % g t rre rre lta or L Vol Cur Cur cy ( t Vo t Cu put Cu acit put put put cien Inpu Inpu In Out Out Out Effi Cap Order # SINGLE OUTPUT P26NG-053R3E2:1LF P26NG-0505E2:1LF P26NG-0509E2:1LF P26NG-0512E2:1LF P26NG-0515E2:1LF P26NG-0524E2:1LF P26NG-123R3E2:1LF P26NG-1205E2:1LF P26NG-1209E2:1LF P26NG-1212E2:1LF P26NG-1215E2:1LF P26NG-1224E2:1LF P26NG-243R3E2:1LF P26NG-2405E2:1LF P26NG-2409E2:1LF P26NG-2412E2:1LF P26NG-2415E2:1LF P26NG-2424E2:1LF P26NG-483R3E2:1LF P26NG-4805E2:1LF P26NG-4809E2:1LF P26NG-4812E2:1LF P26NG-4815E2:1LF P26NG-4824E2:1LF 4.5-9 4.5-9 4.5-9 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 105 105 105 105 105 105 55 55 55 55 55 55 30 30 30 30 30 30 15 15 15 15 15 15 1144 1519 1445 1428 1428 1428 470 602 595 588 588 581 229 301 294 294 287 287 117 156 147 149 145 148 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 9 12 15 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1300 1200 666 500 400 250 1300 1200 666 500 400 250 1300 1200 666 500 400 250 1300 1200 666 500 400 250 75 78 83 84 84 84 76 83 84 85 85 86 78 83 85 85 87 87 76 80 85 84 86 84 6600 3300 2000 1600 1400 680 6600 3300 2000 1600 1400 680 6600 3300 2000 1600 1400 680 6600 3300 2000 1600 1400 680 DUAL OUTPUT P26NG-0505Z2:1LF P26NG-0512Z2:1LF P26NG-0515Z2:1LF P26NG-1205Z2:1LF P26NG-1212Z2:1LF P26NG-1215Z2:1LF P26NG-2405Z2:1LF P26NG-2412Z2:1LF P26NG-2415Z2:1LF P26NG-4805Z2:1LF P26NG-4812Z2:1LF P26NG-4815Z2:1LF 4.5-9 4.5-9 4.5-9 9-18 9-18 9-18 18-36 18-36 18-36 36-72 36-72 36-72 105 105 105 55 55 55 20 20 20 15 15 15 1481 1428 1428 609 595 581 304 297 297 152 147 147 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ±5 ± 12 ± 15 ±5 ± 12 ± 15 0 0 0 0 0 0 0 0 0 0 0 0 ± 600 ± 250 ± 200 ± 600 ± 250 ± 200 ± 600 ± 250 ± 200 ± 600 ± 250 ± 200 81 84 84 82 84 86 82 84 84 82 85 85 ± 2000 ± 900 ± 660 ± 2000 ± 900 ± 660 ± 2000 ± 900 ± 660 ± 2000 ± 900 ± 660 If you need other specifications, please enquire. For optional Control Pin, please add “C” between P and 26 For example: PC26NG-2405Z2:1LF PMB-Series – P(C)26NG-xxxxE/Z2:1LF – Single / Dual Output – SIP8 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 3,50 (0.14) 0.25 (0.01) Package / Pinning / Derating 0.50 (0.02) All dimensions are typical in millimeters (inches). - Pin diameter: 1.0 +/-0.05 (0.04 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 0.50 (0.02) 9.20 (0.36) 21.85 (0.86) 11.10 (0.44) PEAK 3.05 (0.12) Modelcode Datecode 2 2.54 (0.1) 3 6 5 7 8 0.50 (0.02) 1 17.78 (0.70) SIP8 – PLASTIC CASE OUTPUT POWER TEMPERATURE DERATING GRAPH 100% 75% 50% 25% -20% 65 -40 -20 0 20 40 60 90 80 100 PIN CONNECTIONS # SINGLE DUAL SINGLE "C" 1 - Vin - Vin - Vin 2 +Vin +Vin +Vin 3 Omitted N.C. Ctrl. 5 Omitted N.C. N.C. 6 +Vout +Vout +Vout 7 - Vout Common - Vout 8 N.C. - Vout N.C. DUAL "C" - Vin +Vin Ctrl. N.C. +Vout Common - Vout AMBIENT TEMPERATURE (°C) App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH and source capacitor Cin (47uF, ESR<1Ohm at 100KHz) 2 = One load is 25% to 100%, the other load is 100% load, the output voltage variable is within ±5% 3 = Measured with a 0.1uF ceramic capacitor 4 = Tested by normal Vin and 100%-25% load, 25% load step change 5 = Tested by minimal Vin and constant resistive load Operation at no-load conditions will not damage these devices, however they may not meet all specifications. PMB-Series – P(C)26NG-xxxxE/Z2:1LF – Single / Dual Output – SIP8 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 App Notes Test Configurations P26NG-05xxE/Z2:1LF P26NG-12xxE/Z2:1LF C1 Electrolytic capacitor 220uF/100V - C2 & C3 MLCC 22uF/25V L 10uH C4 & C5 MLCC 220pF/3KV MLCC 10uF/50V 10uH MLCC 220pF/3KV P26NG-24xxE/Z2:1LF - MLCC 10uF/50V 10uH MLCC 220pF/3KV P26NG-48xxE/Z2:1LF - MLCC 2.2uF/100V 10uH MLCC 220pF/3KV EMC Specifications Radiated Emissions Conducted Emissions EN55022 EN55022 Class A Class A ESD RS EFT Surge CS PFMF IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 IEC 61000-4-5 IEC 61000-4-6 IEC 61000-4-8 Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Input filter components are required to help meeting conducted emission class A, which application refer to the EMI Filter of design & feature configuration. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. The Remote on/off control: ON: open or high impedance OFF: 2 – 4 mA input current (via 1kOhm) Off stand by input current (Nominal Vin): 2.5mA PMB-Series – P(C)26NG-xxxxE/Z2:1LF – Single / Dual Output – SIP8 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4