ALUMINUM ELECTROLYTIC CAPACITORS WX 5.5mmL Chip Type series Chip type with 5.5mm height. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Load life of 2000 hours at 85°C. WT High Temperature WP WX Bi-Polarized Low Profile ZS Specifications Item Performance Characteristics Category Temperature Range — 40 ~ +85°C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 330µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3(µA),whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C tan δ Rated voltage(V) tan δ (MAX.) 4 6.3 10 16 25 35 50 0.35(0.40) 0.26(0.30) 0.20(0.24) 0.16(0.19) 0.14(0.16) 0.12(0.14) 0.12(0.14) 6.3 4 8 4 7 15 Rated voltage(V) Z—25°C/ Z+20°C Z—40°C/ Z+20°C Stability at Low Temperature Impedance ratio ZT/Z20(MAX.) 10 3 8 200% or less of initial specified value Initial specifed value or less Leakage Current Shelf Life After leaving capacitors under no load at 85°C for 1000 hours, they meet the specified value for endurance characteristics listed above. Resistance to soldering heat The capacitors shall be kept on the hot plate maintained at 250°C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the characteristics requirements listed at right. Marking Black print on the case top. Chip Type Within ±10% of initial value Initial specified value or less Leakage current Initial specified value or less Type numbering system (Example : 16V 10µF) 5.4 1 A±0.2 +0.1 –0.2 0.5 ~ 0.8 2 3 4 5 6 7 8 9 10 11 12 13 14 UWX 1 C 1 0 0 MC R 1 G B A±0.2 B±0.2 C±0.2 0.5 MAX. Plastic platform 0.3 MAX. E 1 Voltage φD±0.5 X2 10 16V Capacitance change tan δ Positive Capacitance 2 Lot No. ) applicable to WR, φ3 case size. Within ±20% of initial value (Within ±2%5 for 4 V and φ3,WR series units) Capacitance change tan δ After 2000 hours' application of rated voltage at 85°C, capacitors meet the characteristics requirements listed at right. Endurance Values in ( Measurement frequency : 120Hz 16 25 35 50 2 2 2 2 4 4 3 3 Negative 1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated voltage is omitted. 2. In case of marking for φ3 units, Lot No.is expressed by a digit (month code). φD A B C E 3 1.5 3.3 3.3 0.8 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3 Taping code Case dia.code Configuration Capacitance toleranc (±20%) Rated Capacitance (10µF) φD Code 3 2 4~8 1 Rated voltage (16V) Series name Type Dimension table in next page. CAT.8100P ALUMINUM ELECTROLYTIC CAPACITORS WX series Dimensions 4 0G V Cap. (µF) Code 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4(3) 1.0 0.22 R22 4(3) 2.0 0.33 R33 4(3) 2.8 0.47 R47 4(3) 4.0 1 010 4(3) 2.2 2R2 3.3 3R3 4.7 4R7 3 13(10) 3 10 4 17 4(3) 16(12) 4 18 5 20(18) 23(18) 5 27(24) 5 29(24) 6.3 33(30) 33(30) 5 37(30) 6.3 42(38) 6.3 46(39) 8 52(43) 5 41(34) 6.3 49(44) 6.3 52(46) 8 62(53) 8 71 45(40) 6.3 52(47) 6.3 58(52) 8 70(60) 8 80 100 22 220 3 019 4(3) 28(21) 5 33 330 4 028 5 37(34) 47 470 4 033 5 56 560 5 042 6.3 52(46) 6.3 57(50) 6.3 63(57) 8 100 101 5 056 6.3 70(47) 6.3 76(54) 6.3 86 8 150 151 6.3 079 6.3 71 8 111(76) 220 221 6.3 096 8 110(74) 8 135 331 8 145 8 170 ( ) is also available with φ3mm upon request. } 8.4(8.0) 4(3) 4(3) 10 Size φ4 is available for capacitors marked. " " Size φ5 is available for capacitors marked. " " Size φ6.3 is available for capacitors marked. " " 8.4 76(65) 110 Case size Rated ripple Rated Ripple (mA rms) at 85°C 120Hz ( ) = WR Series In such a case, W R will be put at 2nd and 3rd digit of type numbering system. Frequency coefficient of allowable ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz ~ 1.50 Taping Specifications are given in page 21. Please refer to page 3 for the minimum order quantity. CAT.8100P