Switch Ready Specification Sheet

Switch Ready Network Zone System
specifications
The switch ready network zone system shall include copper/fiber uplinks
and downlinks optimized for industrial Ethernet switches. System shall
incorporate redundant power supplies with maintenance - free UPS.
The enclosure shall be UL Type 4/12/4X and IP66 rated. A removable,
pre-engineered back plate with DIN rails shall be incorporated in the
enclosure. Pre-installed accessory side panels, fiber slack spool, and
L rings shall be included for cable management. The door shall be
secured with 3mm double bit or slotted latch drive feature. The door
shall hinge on the right or left. Class 2 power circuits shall be pre-wired,
labeled, and tested. A barrier shall be present to isolate IT personnel
from high voltage power circuit.
technical information
Standards:
UL 508A Standard for Industrial Control Panels, UL Type 4/12 or 4X, IP66 Rated
Dimensions:
Z23R: 36.0"H x 24.0"W x 11.7"D (914mm x 610mm x 297mm)
Z22R: 24.0"H x 24.0"W x 11.7"D (610mm x 610mm x 297mm)
Color and material:
Enclosures: Gray, 14 gauge cold roll steel or 316 stainless steel
Back panels: 14 gauge galvannealed steel or 304 stainless steel
Thermal analysis:
Validated to 40°C ambient outside of enclosure or 60°C maximum within
enclosure at up to 95% (non-condensing) humidity
Installation:
Wall mount with optional outside-mount flange
key features and benefits
Switch ready solution:
Reduces time required for planning, designing, procurement, and
installation, resulting in simpler specification and faster implementation
Designed to accept
customer supplied
industrial switches:
Offer management and diagnostics from within IT and controls
environments to optimize network traffic
Copper/fiber uplinks
Enables troubleshooting of network connections and verification of
or patch field and
field terminations
copper/fiber connectivity:
Installed no battery,
maintenance-free UPS:
Prevents rebooting of switch during short power outages and includes
networked remote management which monitors Hold Time and Lifetime
from the plant floor or office, saving time and money
Included redundant
power supplies:
Minimize the risk of equipment failure for improved network reliability
Isolation barrier:
Segregates higher line voltage from lower voltage switch for
increased safety
Bonding provisions and
grounding bar:
Ensure path to ground to protect personnel and equipment
Gland plate:
Allows quick and easy access to machine ingress points into enclosure
Detailed installation
guide:
Provides easy, repeatable design instructions assuring consistency and
saving time on the job-site
applications
The Panduit Switch Ready Network Zone System
is designed to rapidly deploy an EtherNet/IP***
network between the enterprise and plant floor.
Copper/fiber connectivity and power features
minimize engineering and installation time resulting
in faster implementation. The Switch Ready Network
Zone System provides usability similar to IT
switches for industrial switches on the plant floor.
This ensures that management and control of the
network does not get in the way of making the
most effective use of available network data.
With UL Type 4/12/4X and IP66 ratings, the
enclosures provide reliability and high performance,
as an integral component of the end-to-end solution
for Industrial Networks.
*Rockwell Automation and Allen-Bradley are registered by Rockwell
Automation in the Patent and Trademark Office of the United States.
**Stratix, Stratix 8000, Stratix 5700 and Integrated Architecture are
trademarks of Rockwell Automation.
***EtherNet/IP is a trademark of ODVA.
w w w . pa n d u it.c o m /n e two rkzone
SPECIFICATION SHEET
Switch Ready Network Zone System
See part number table on pages 2-3
Related Products
PanZone® NEMA 4X Rated
Compression Fittings
Cable diameters
0.115" – 0.250":
Cable diameters
0.230" – 0.395":
Cable diameters
0.170" – 0.450":
Drain kit:
PZNF1
PZNF2
PZNF3
PZNDVK
IndustrialNet ™ TX6™ Connectors
Category 6
UTP bulkhead
connector:
Category 6
STP bulkhead
connector:
IAEBH6
IAEBH6S
Fiber Uplink Accessories
Surface mount
fiber box:
CBXF6BL-AY
LC OptiCam®
connector:
FLCDMCXAQY
LC connector
module:
CMDSAQLCBL
LC patch 10Gig
patch cord:
FXE10-10M1Y
Opti-Core® Interlocking
Armored Cable:
FOPRX12Y
DIN Rail Patching Accessories
Mini-Com ® Copper
8-Port DIN Rail
Patch Panel:
Mini-Com® Fiber
8-Port DIN Rail
Patch Panel:
Mini-Com® Single
Port DIN Rail
Mount Adapter:
CDPP8RG
FDME8RG
CADIN1IG^
IndustrialNet ™ TX6™ PLUS
Patch Cords
UTP with
dust cap:
UTP without
dust cap
Shielded with
dust cap:
Shielded without
dust cap:
IUTPSP3BL^^
IUTPSPNC3BL^^
ISTPSP1MBL^^^
ISTPSPNC1MBL^^^
TX6500™ Copper Cable
Category 6, UTP:PUR6504BU-UY
Suggested Allen-Bradley* Stratix**
products, available from
Rockwell Automation*
1783-MS10T Stratix 8000** switch
1783-MX08T Stratix 8000 copper
expansion module
1783-MX08F Stratix 8000 fiber
expansion module
1783-BMS10CGN Stratix 5700**
10-port switch with
Network Address Translation (NAT)
1783-BMS20CGN Stratix 5700
20-port switch with NAT
^For standard colors other than International
Gray, replace IG in part number with
BL (Black), EI (Electric Ivory),
IW (Off White), or WH (White).
^^For lengths other than 3 feet (5, 7, 10, 15,
or 20 feet) change the length designation in
the part number to the desired length.
^^^For lengths other than 1 meter
(2, 3, or 5 meters) change the length
designation in the part number to the
desired length.
Switch Ready Network Zone System
Control Room
Manufacturing Cell
Zone Infrastructure
Deploying Zone Network Topology
A highly effective way to deploy EtherNet/IP*** solutions in a plant floor environment is to follow the recommendations from Rockwell
Automation* and Cisco**** in their Converged Plantwide Ethernet (CPwE) design and implementation guide. In this guide the use of
zoned network topology is recommended as a best practice.
Using Panduit’s Network Zone System integrated with Stratix** switches from Rockwell Automation* provides a platform for
implementing small VLANs for Cell/Area Zones, as recommended in the CPwE to improve manageability and limit Layer 2
broadcast domains‡.
S
S
T
A
S
C
T
K
A
1
C
K
T
A
S
C
T
K
A
2
C
K
1
2
C
O
NS
C
OL
O
E
NS
OL
E
Plant
Level
Zone
R
10
1 .6
0A-A 0 24
.9
TA
I ,
R
50010
N-60
VA 1 .6
0A-Z
H
G
0 24
.9
T~ A
I ,
500N-60
V
HG
~Z
Machine
Level
Zone
A
D
C
C
A
D
C
C
A
D
C
C
The zone enclosures allow all cables within a Cell/Area Zone to be managed and patched within a single enclosure. By using a zone
cabling architecture approach, network cabling becomes easier to locate, manage, and maintain because each additional device is
routed within the same pathways and enclosures. Managed cabling helps reduce the number of home runs throughout a facility and
helps reduce abandoned cable in plenum spaces, helping make the workplace run more efficiently and safely.
Following a zone topology allows a highly scalable and flexible deployment using building blocks of the CPwE architecture.
Switch Ready Network Zone Systems - More options available at www.panduit.com/networkzone
Part number
Layout
Image
Enclosure
Type
Z23R-S15
4/12 Steel
Z23R-S15S
4/12 Steel
Z23R-615
4X 316 SS
Z23R-615S
4X 316 SS
Z23R-S25
4/12 Steel
Z23R-S25S
4/12 Steel
Z23R-625
4X 316 SS
Z23R-625S
4X 316 SS
Z22R-S15
4/12 Steel
Z22R-S15S
4/12 Steel
Industrial
Switch(es)
(1) user defined
industrial switch
with max power
of 35 watts
at 24 Vdc
Downlink Port
Connectivity Provided
(6) LC adaptors, (2) LC patch cords
(16) Cat 6 STP jacks and cords
(6) LC adaptors, (2) LC patch cords
(16) Cat 6 UTP jacks and cords
(6) LC adaptors, (2) LC patch cords
(16) Cat 6 UTP jacks and cords
19" 48-port patch
panel CPP48WBLY
(16) Cat 6 UTP jacks and cords
(6) LC adaptors, (4) LC patch cords
(16) Cat 6 STP jacks and cords
(6) LC adaptors, (4) LC patch cords
(6) LC adaptors, (2) LC patch cords
(6) LC adaptors, (2) LC patch cords
(1) 8-port patch
panel CDPP8RG
Z22R-615
4X 316 SS
Z22R-615S
4X 316 SS
(8) Cat 6 STP jacks and cords
(6) LC adaptors, (2) LC patch cords
Z22R-S25
4/12 Steel
(16) Cat 6 UTP jacks and cords
(6) LC adaptors, (4) LC patch cords
Z22R-S25S
4/12 Steel
Z22R-625
4X 316 SS
Z22R-625S
4X 316 SS
(2) user defined
industrial
switches with
max power
of 35 watts
at 24 Vdc
(8) Cat 6 UTP jacks and cords
(16) Cat 6 STP jacks and cords
(16) Cat 6 UTP jacks and cords
(16) Cat 6 STP jacks and cords
Power Input
Din Rail
Mounting
Cable
Management
Isolation
Barrier
Gland Plate
7 inch deep
strain relief bar
and adjustable
ring managers
Barrier to cover
high voltage
equipment on
lower DIN rail
One removable
machinable gland plate
(3) 16.7
inch long
DIN rails
(6) LC adaptors, (4) LC patch cords
(6) LC adaptors, (4) LC patch cords
(8) Cat 6 STP jacks and cords
Panduit Industrial Network UPS
(6) LC adaptors, (2) LC patch cords
(16) Cat 6 STP jacks and cords
(8) Cat 6 UTP jacks and cords
(1) user defined
industrial switch
with max power
of 35 watts
at 24 Vdc
Uplink Port
Connectivity Provided
(16) Cat 6 UTP jacks and cords
(16) Cat 6 STP jacks and cords
(2) user defined
industrial
switches with
max power
of 35 watts
at 24 Vdc
Downlink
Patch Field
No battery, maintenancefree UPS with remote
management UPS003024024015;
Estimated Hold Time = 7 minutes
fully expanded with Load
Sense Module UPS003LSM
(one UPS and LSM per switch)
100-250 Vac
Single Phase
(6) LC adaptors, (2) LC patch cords
(2) 16.7
inch long
DIN rails
(6) LC adaptors, (4) LC patch cords
(2) 8-port patch
panels CDPP8RG
(6) LC adaptors, (4) LC patch cords
(6) LC adaptors, (4) LC patch cords
‡
For additional reference see the Panduit Popular Configuration Drawing “Overview of Industrial Switch Deployment” PCD0001.
Leveraging the Rockwell Automation* Integrated Architecture** technology simplifies switch configuration and integration while providing machine-based diagnostics and troubleshooting tools. Stratix** Industrial Ethernet Switches also leverage the Cisco**** operating system, bringing the world’s leading switching technology to the plant floor environment. Advanced
switch feature sets include: STP/RSTP/MST, Resilient Ethernet Protocol (REP), Flexlinks, EtherChannel (link aggregation), QoS, IGMP snooping with querier, VLANs with trunking, IEEE 1588 PTP v2, IPv6 support, storm control with alarming, egress traffic shaping; compatible with Cisco**** Network Assistant (CNA) and CiscoWorks.
*Rockwell Automation and Allen-Bradley are registered by Rockwell Automation in the Patent and Trademark Office of the United States.
**Stratix, Stratix 8000, Stratix 5700 and Integrated Architecture are trademarks of Rockwell Automation. ***EtherNet/IP is a trademark of ODVA. ****Cisco is a registered trademark of Cisco Technology Inc.
Switch Ready Network Zone System
configuration options
Z23R-S25
Z22R-S15
WORLDWIDE SUBSIDIARIES AND SALES OFFICES
PANDUIT CANADA
Markham, Ontario
[email protected]
Phone: 800.777.3300
PANDUIT EUROPE LTD.
London, UK
[email protected]
Phone: 44.20.8601.7200
PANDUIT SINGAPORE PTE. LTD.
Republic of Singapore
[email protected]
Phone: 65.6305.7575
PANDUIT JAPAN
Tokyo, Japan
[email protected]
Phone: 81.3.6863.6000
PANDUIT LATIN AMERICA
Guadalajara, Mexico
[email protected]
Phone: 52.33.3777.6000
PANDUIT AUSTRALIA PTY. LTD.
Victoria, Australia
[email protected]
Phone: 61.3.9794.9020
For a copy of Panduit product warranties, log on to www.panduit.com/warranty
For more information
Visit us at www.panduit.com
Contact Customer Service by email: [email protected]
or by phone: 800.777.3300
©2015 Panduit Corp.
ALL RIGHTS RESERVED.
ZCSP20--WW-ENG
10/2015