Datasheet

UNISONIC TECHNOLOGIES CO., LTD
U74LV00
CMOS IC
QUADRUPLE 2-INPUT
NAND GATE

DESCRIPTION
The U74LV00 is designed for 2V to 5.5V VCC operation.
The U74LV00 provides the function Y=A  B or Y=A  B in
positive logic.
The device is fully specified for partial-power-down applications
using Ioff. The Ioff circuitry disables the outputs, preventing damaging
current backflow through the devices when it is powered down.

FEATURES
* 2V to 5.5V VCC Operation
* Max tPD of 6.5ns at 5V
* Typical VOLP (Output Ground Bounce)<0.8V at VCC=3.3V,TA=25°C
* Typical VOHV (output VOH Undershoot)>2.3V at VCC=3.3V,TA=25°C
* Support Mixed-Mode Voltage Operation on All Ports
* Ioff Supports Partial-Power-Down Mode Operation

ORDERING INFORMATION
Ordering Number
Lead Free
Halogen Free
U74LV00L-P14-T
U74LV00G-P14-T
U74LV00L-P14-R
U74LV00G-P14-R
www.unisonic.com.tw
Copyright © 2013 Unisonic Technologies Co., Ltd
Package
Packing
TSSOP-14
TSSOP-14
Tube
Tape Reel
1 of 5
QW-R502-960,A
U74LV00


CMOS IC
PIN CONFIGURATION
1A
1
14
VCC
1B
2
13
4B
1Y
3
12
4A
2A
4
11
4Y
2B
5
10
3B
2Y
6
9
3A
GND
7
8
3Y
FUNCTION TABLE
INPUT(nA)
INPUT(nB)
H
H
H
L
L
H
L
L
Note: H: HIGH voltage level; L: LOW voltage level.

OUTPUT(nY)
L
H
H
H
LOGIC DIAGRAM (Positive Logic)
Logic Symbol
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
IEC Logic Symbol
2 of 5
QW-R502-960 A
U74LV00

CMOS IC
ABSOLUTE MAXIMUM RATING
PARAMETER
SYMBOL
RATINGS
UNIT
Supply Voltage
VCC
-0.5 ~ 7
V
Input Voltage range(see note 2)
VIN
-0.5 ~ 7
V
Voltage range applied to any output in the
-0.5 ~ 7
V
VO
high-impedance or power-off state(see note 2)
Output Voltage range(see note 2 and 3)
VO
-0.5 ~ VCC+0.5
V
Continuous current through VCC or GND
ICC
±50
mA
Input Clamp Current (VIN<0)
IIK
-20
mA
Output Clamp Current (VOUT<0 or VOUT>VCC)
IOK
-50
mA
Continuous output current
IO
±25
mA
Storage temperature ranges
TSTG
-65 ~ +150
°C
Note: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. The input and output negative-voltage ratings may be exceeded if the output current ratings are observed.
3. The value is limited to 5.5V maximum.

THERMAL DATA
PARAMETER
Junction to Ambient

SYMBOL
θJA
RATINGS
113
UNIT
°C/W
RECOMMENDED OPERATING CONDITIONS
PARAMETER
Supply Voltage
SYMBOL
VCC
High-Level Input Voltage
VIH
TEST CONDITIONS
Operating
VCC=2V
VCC=2.3V to 2.7V
VCC=3V to 3.6V
VCC=4.5V to 5.5V
VCC=2V
VCC=2.3V to 2.7V
VCC=3V to 3.6V
VCC=4.5V to 5.5V
MIN
2
1.5
VCC×0.7
VCC×0.7
VCC×0.7
TYP
MAX
5.5
V
0.5
VCC×0.3
Low-Level Input Voltage
VIL
VCC×0.3
VCC×0.3
Input Voltage
VIN
0
5.5
Output Voltage
VOUT
0
VCC
200
VCC=2.3V to 2.7V
Input transition rise or fall time
∆t/∆v
VCC=3V to 3.6V
100
VCC=4.5V to 5.5V
20
Operating free-air Temperature
TA
-40
85
Note: All unused inputs of the device must be held at VCC or GND to ensure proper device operation.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
UNIT
V
V
V
V
ns/V
°C
3 of 5
QW-R502-960 A
U74LV00

CMOS IC
ELECTRICAL CHARACTERISTICS (TA =25°C , unless otherwise specified)
PARAMETER
SYMBOL
TEST CONDITIONS
VCC=2V to 5.5V, IOH=-50μA
High-Level Output Voltage
VOH
Low-Level Output Voltage
VOL
Input Leakage Current
Quiescent Supply Current
Power OFF Leakage Current
II(LEAK)
IQ
Ioff
Input Capacitance

CIN
SYMBOL
Propagation Delay From Input
(nA or nB) To Output(nY)
tPD
TEST CONDITIONS
CL=15pF
VCC=2.5±0.2V
CL=50pF
CL=15pF
VCC=3.3V±0.3V
CL=50pF
CL=15pF
VCC=5±0.5V
CL=50pF
UNIT
V
0.1
0.4
0.44
0.55
±1
20
5
3.3
3.3
V
μA
μA
μA
pF
MIN
TYP
7.1
9.6
5
6.9
3.6
4.9
MAX
12.9
16.6
7.9
11.4
5.5
7.5
UNIT
Ns
Ns
Ns
Ns
NOISE CHARACTERISTICS (TA=25°C, VCC=3.3V,CL=50pF)
PARAMETER
SYMBOL
Quiet Output, Maximum Dynamic VOL
VOL(P)
Quiet Output, Minimum Dynamic VOL
VOL(V)
Quiet Output, Minimum Dynamic VOH
VOH(V)
High-Lelel Dynamic Input Voltage
VIH(D)
Low-Level Dynamic Input Voltage
VIL(D)
Note: Characteristics are for surface-mount packages only.

MAX
SWITCHING CHARACTERISTICS (TA=25°С)
PARAMETER

VCC=2.3V , IOH=-2mA
VCC=3V, IOH=-6mA
VCC=4.5V, IOH=-12mA
VCC=2V to 5.5V, IOH=50μA
VCC=2.3V, IOH=2mA
VCC=3V, IOH=6mA
VCC=4.5V, IOH=12mA
VIN=5.5V or GND, VCC=0 to 5.5V
VIN=VCC or GND, IOUT=0, VCC=5.5V
VIN or VOUT=0 to 5.5V
VIN=VCC or GND, VCC=3.3V
VIN=VCC or GND, VCC=5V
MIN TYP
VCC-0.
1
2
2.48
3.8
MIN
TYP
0.2
-0.1
3.1
MAX
0.8
-0.8
2.31
0.99
UNIT
V
V
V
V
V
OPERATING CHARACTERISTICS (TA=25°С)
PARAMETER
SYMBOL
Power Dissipation Capacitance
CPD
TEST CONDITIONS
VCC=3.3V
CL=50pF, f=10MHz
VCC=5V
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
MIN
TYP
9.5
11
MAX
UNIT
pF
4 of 5
QW-R502-960 A
U74LV00

CMOS IC
TEST CIRCUIT AND WAVEFORMS
Test Point
From Output
CL
TEST CIRCUIT
Note: 1. CL includes probe and jig capacitance.
2. All input pulses are supplied by generators having the following characteristics:
PRR ≤1MHz, ZO=50Ω, tr ≤ 3ns, tf ≤ 3ns
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 5
QW-R502-960 A