Photomicrosensor (Transmissive) EE-SX460-P1 Be sure to read Precautions on page 25. ■ Dimensions ■ Features Note: All units are in millimeters unless otherwise indicated. • • • • • • 171826-3 (Tyco Electronics AMP) Optical axis Snap-in mounting model. Mounts to 0.8- to 1.6-mm-thick panels. High resolution (aperture width of 0.5 mm) With a 5-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMP’s EI-series connectors. ■ Absolute Maximum Ratings (Ta = 25°C) 0.5 (Aperture width) Optical axis Two, R1 15±0.2 Item Symbol VCC 10 V Output voltage VOUT 28 V Output current IOUT 16 mA Permissible output dissipation POUT 250 mW (see note) Ambient temper- Operating ature Storage Topr –20°C to 75°C Tstg –40°C to 85°C Soldering temperature Tsol --- Mounting face Note: Refer to the temperature rating chart if the ambient temperature exceeds 25°C. Internal Circuit V Rated value Power supply voltage Unless otherwise specified, the tolerances are as shown below. O G Terminal No. V O G Dimensions Tolerance 3 mm max. ±0.3 Name 3 < mm ≤ 6 ±0.375 Power supply (Vcc) 6 < mm ≤ 10 ±0.45 Output (OUT) Ground (GND) 10 < mm ≤ 18 ±0.55 18 < mm ≤ 30 ±0.65 Recommended Mating Connectors: Tyco Electronics AMP 171822-3 (crimp connector) 172142-3 (crimp connector) OMRON EE-1005 (with harness) ■ Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V±10%) Item Symbol Value Condition Current consumption ICC 30 mA max. With and without incident Low-level output voltage VOL 0.3 V max. IOUT = 16 mA with incident High-level output voltage VOH (VCC x 0.9) V min. VOUT = VCC without incident, RL = 47 kΩ Response frequency f 3 kHz min. VOUT = VCC, RL = 47 kΩ (see note) Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 144 0.5 mm t = 0.2 mm EE-SX460-P1 Photomicrosensor (Transmissive) ■ Engineering Data d1 = 0±0.3 mm Light interrupting plate Center of optical axis Output transistor VCC = 5 V Ta = 25°C RL = 47 kΩ d2 = 0±1.1 mm VCC = 5 V Ta = 25°C RL = 47 kΩ d OFF d2 ON −3 Distance d (mm) Ambient temperature Ta (°C) Center of optical axis Sensing Position Characteristics (Typical) Sensing Position Characteristics (Typical) Output transistor Output allowable dissipation Pc (mW) Output Allowable Dissipation vs. Ambient Temperature Characteristics −2 −1 0 1 2 3 Distance d (mm) EE-1005 Connector 1,000±20 (1) (2) No. (3) Name Model Quantity Maker 1 Receptacle 171822-3 housing 1 Tyco Electronics AMP 2 Receptacle 170262-1 contact 3 Tyco Electronics AMP 3 Lead wire 3 --- UL1007 AWG24 Wiring Connector circuit no. 1 Lead wire color Output when connected to EE-SX460-P1 Red VCC 2 Orange OUT 3 Yellow GND ■ Recommended Mounting Hole Dimensions and Mounting and Dismounting Method Dismounting by Hand Squeeze the mounting tabs as shown in the following illustration and press the mounting tabs upwards. Center of sensing slot Optical axis EE-SX460-P1 Sensor edge Sensor edge on connector side (2) The Photomicrosensor can be mounted to 0.8- to 1.6-mm-thick panels. Refer to the above mounting hole dimensions and open the mounting holes in the panel to which the Photomicrosensor will be mounted. Insert into the holes the Photomicrosensor’s mounting portions with a force of three to five kilograms but do not press in the Photomicrosensor at one time. The Photomicrosensor can be easily mounted by inserting the mounting portions halfway and then slowly pressing the Photomicrosensor onto the panel. There are two ways to dismount the Photomicrosensor. Refer to the following. Dismounting with Screwdriver Press the mounting hooks of the Photomicrosensor with a flat-blade screwdriver as shown in the following illustration and pull up the Photomicrosensor. Panel (1) (1) Pressed mounting holes are ideal for mounting the Photomicrosensor. When mounting the Photomicrosensor to a panel that has pressed mounting holes for the Photomicrosensor, be sure to mount the Photomicrosensor on the pressing side of the panel, otherwise it may be difficult to mount the Photomicrosensor and an insertion force of five to six kilograms may be required. When mounting the Photomicrosensor to a panel that has mounting holes opened by pressing, make sure that the mounting holes have no burrs, otherwise the lock mechanism of the Photomicrosensor will not work perfectly. After mounting the Photomicrosensor to a panel, be sure to check if the lock mechanism is working perfectly. EE-SX460-P1 EE-SX460-P1 Flat-blade screwdriver (2) Flat-blade (2) screwdriver (1) (1) Mounting hook Panel Mounting hook This tapered portion must be on the lower side of the panel, other wise the Photomicrosensor will not be locked in. Panel Mounting tab EE-SX460-P1 Photomicrosensor (Transmissive) 145