Photomicrosensor EE-SX3239-P2/-SX4239-P2 Dimensions Note: Features All units are in millimeters unless otherwise indicated. Post header 175489-3 (Tyco Electronics AMP) (2.4), Aperture width (Transmissive) 0.5, Aperture width • • • • • Snap-in mounting model. • Connects to Tyco Electronics AMP’s CT-series connectors. Mounts to 1.0-, 1.2- and 1.6-mm-thick panels. High resolution with a 0.5-mm-wide sensing aperture. With a 5-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Absolute Maximum Ratings (Ta = 25°C) Item Note: Internal Circuit The asterisked dimension is specified by datum A only. Unless otherwise specified, the tolerances are as shown below. V O Terminal No. V O G Name Power supply (Vcc) Output (OUT) Ground (GND) Dimensions Tolerance 3 mm max. ±0.3 3 t mm v 6 ±0.375 6 t mm v 10 ±0.45 10 t mm v 18 ±0.55 18 t mm v 30 ±0.65 Rated value Power supply voltage VCC 7V Output voltage VOUT 28 V Output current IOUT 16 mA Permissible output dissipation POUT 250 mW (see note) Ambient temperature p Operating Topr –20°C to 75°C Storage Tstg –40°C to 85°C Tsol --- Soldering temperature Note: G Symbol Refer to the temperature rating chart if the ambient temperature exceeds 25°C. Recommended Mating Connectors: Tyco Electronics AMP 175778-3 (crimp-type connector) 173977-3 (press-fit connector) Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V ±10%) Item Symbol Value Condition Current consumption ICC 16.5 mA max. With and without incident Low-level output voltage VOL 0.35 V max. IOUT = 16 mA without incident (EE-SX3239-P2), with incident (EE-SX4239-P2) High-level output voltage VOH (VCC x 0.9) V min. VOUT = VCC with incident (EE-SX3239-P2), without incident (EE-SX4239-P2), RL = 47 kΩ Response frequency f 3 kHz min. VOUT = VCC, RL = 47 kΩ (see note) Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 186 0.5 mm t = 0.2 mm EE-SX3239-P2/-SX4239-P2 EE-SX3239-P2/-SX4239-P2 Engineering Data Output allowable dissipation Pc (mW) Output Allowable Dissipation vs. Ambient Temperature Characteristics Sensing Position Characteristics (Typical) VCC = 5 V Ta = 25°C RL = 47 kΩ (OFF) Center of optical axis Light interrupting plate Output transistor d1 = 0±0.3 mm (ON) Ambient temperature Ta (°C) Distance d (mm) Recommended Mounting Holes • When mounting the Photomicrosensor to a panel with a hole opened by pressing, make sure that the hole has no burrs. The mounting strength of the Photomicrosensor will decrease if the hole has burrs. • When mounting the Photomicrosensor to a panel with a hole opened by pressing, be sure to mount the Photomicrosensor on the pressing side of the panel. • The mounting strength of the Photomicrosensor will increase if the Photomicrosensor is mounted to a panel with a hole that is only a little larger than the size of the Photomicrosensor, in which case, however, it will be difficult to mount the Photomicrosensor to the panel. The mounting strength of the Photomicrosensor will decrease if the Photomicrosensor is mounted to a panel with a hole that is comparatively larger than the size of the Photomicrosensor, in which case, however, it will be easy to mount the Photomicrosensor to the panel. When mounting the Photomicrosensor to a panel, open an appropriate hole for the Photomicrosensor according to the application. • After mounting the Photomicrosensor to any panel, make sure that the Photomicrosensor does not wobble. • When mounting the Photomicrosensor to a molding with a hole, make sure that the edges of the hole are sharp enough, otherwise the Photomicrosensor may fall out. 187