VS-25TTS...SPbF Series www.vishay.com Vishay Semiconductors Thyristor, Surface Mount, Phase Control SCR, 16 A FEATURES Anode 2, 4 4 • Meets MSL level 1, per LF maximum peak of 260 °C • Designed and JEDEC®-JESD 47 2 3 1 qualified J-STD-020, according • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 3 Cathode Gate 1 TO-263AB (D2PAK) APPLICATIONS • Input rectification (soft start) • Vishay input diodes, switches and output rectifiers which are available in identical package outlines PRODUCT SUMMARY Package TO-263AB (D2PAK) Diode variation Single SCR IT(AV) 16 A VDRM/VRRM 800 V, 1200 V VTM 1.25 V IGT 45 mA TJ -40 to +125 °C DESCRIPTION The VS-25TTS...SPbF High Voltage Series of silicon controlled rectifiers are specifically designed for medium power switching and phase control applications. The glass passivation technology used has reliable operation up to 125 °C junction temperature. OUTPUT CURRENT IN TYPICAL APPLICATIONS APPLICATIONS SINGLE-PHASE BRIDGE THREE-PHASE BRIDGE NEMA FR-4 or G10 glass fabric-based epoxy with 4 oz. (140 μm) copper 3.5 5.5 Aluminum IMS, RthCA = 15 °C/W 8.5 13.5 Aluminum IMS with heatsink, RthCA = 5 °C/W 16.5 25.0 UNITS A Note • TA = 55 °C, TJ = 125 °C, footprint 300 mm2 MAJOR RATINGS AND CHARACTERISTICS PARAMETER IT(AV) TEST CONDITIONS Sinusoidal waveform IRMS 16 25 VRRM/VDRM ITSM VT VALUES 16 A, TJ = 25 °C dV/dt dI/dt TJ UNITS A 800 to 1200 V 350 A 1.25 V 500 V/μs 150 A/μs -40 to +125 °C VDRM, MAXIMUM PEAK DIRECT VOLTAGE V IRRM/IDRM, AT 125 °C mA VOLTAGE RATINGS PART NUMBER VRRM, MAXIMUM PEAK REVERSE VOLTAGE V VS-25TTS08SPbF 800 800 VS-25TTS12SPbF 1200 1200 10 Revision: 08-Jul-15 Document Number: 94383 1 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS...SPbF Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current IT(AV) Maximum RMS on-state current IRMS Maximum peak, one-cycle, non-repetitive surge current ITSM TEST CONDITIONS VALUES TYP. MAX. TC = 93 °C, 180° conduction half sine wave 16 10 ms sine pulse, rated VRRM applied 300 UNITS 25 10 ms sine pulse, no voltage reapplied 350 10 ms sine pulse, rated VRRM applied 450 10 ms sine pulse, no voltage reapplied 630 A Maximum I2t for fusing I2t Maximum I2t for fusing I2t t = 0.1 ms to 10 ms, no voltage reapplied 6300 A2s Maximum on-state voltage drop VTM 16 A, TJ = 25 °C 1.25 V 12.0 m 1.0 V On-state slope resistance Threshold voltage Maximum reverse and direct leakage current rt VT(TO) IRM/IDM TJ = 125 °C TJ = 25 °C TJ = 125 °C Holding current IH VS-25TTS08, VS-25TTS12 Maximum latching current IL Anode supply = 6 V, resistive load, TJ = 25 °C Maximum rate of rise of off-state voltage dV/dt Maximum rate of rise of turned-on current dI/dt 0.5 VR = Rated VRRM/VDRM Anode supply = 6 V, resistive load, initial IT = 1 A, TJ = 25 °C TJ = TJ max., linear to 80 %, VDRM = Rg - k = Open A2s 10 - 150 mA 200 500 V/μs 150 A/μs TRIGGERING PARAMETER Maximum peak gate power SYMBOL TEST CONDITIONS VALUES UNITS PGM 8.0 Maximum average gate power PG(AV) 2.0 Maximum peak positive gate current + IGM 1.5 A Maximum peak negative gate voltage - VGM 10 V Anode supply = 6 V, resistive load, TJ = - 10 °C Maximum required DC gate current to trigger Maximum required DC gate voltage to trigger IGT VGT Maximum DC gate voltage not to trigger VGD Maximum DC gate current not to trigger IGD 60 Anode supply = 6 V, resistive load, TJ = 25 °C 45 Anode supply = 6 V, resistive load, TJ = 125 °C 20 Anode supply = 6 V, resistive load, TJ = - 10 °C 2.5 Anode supply = 6 V, resistive load, TJ = 25 °C 2.0 Anode supply = 6 V, resistive load, TJ = 125 °C 1.0 TJ = 125 °C, VDRM = Rated value W mA V 0.25 2.0 mA VALUES UNITS SWITCHING PARAMETER SYMBOL Typical turn-on time tgt Typical reverse recovery time trr Typical turn-off time tq TEST CONDITIONS TJ = 25 °C TJ = 125 °C 0.9 4 μs 110 Revision: 08-Jul-15 Document Number: 94383 2 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS...SPbF Series www.vishay.com Vishay Semiconductors THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL Maximum junction and storage temperature range TEST CONDITIONS VALUES TJ, TStg Soldering temperature TS Maximum thermal resistance, junction to case RthJC UNITS -40 to +125 For 10 s (1.6 mm from case) 260 DC operation 1.1 °C °C/W Typical thermal resistance, junction to ambient (PCB mount) RthJA (1) 40 Approximate weight 2 g 0.07 oz. 25TTS08S Case style D2PAK (SMD-220) Marking device 25TTS12S 130 Maximum Averag e On-state Power Loss (W) Maximum Allowable Case Tempera ture (°C) Note (1) When mounted on 1" square (650 mm2) PCB of FR-4 or G-10 material 4 oz. (140 μm] copper 40 °C/W For recommended footprint and soldering techniques refer to application note #AN-994 R thJC (DC) = 1.1 °C/ W 120 Conduc tion Angle 110 30° 60° 90° 100 120° 180° 90 0 5 10 15 25 180° 120° 90° 60° 30° 20 15 RMSLimit 10 Conduc tion Angle 5 TJ= 125°C 0 20 0 Maximum Averag e On-state Power Loss (W) Maximum Allowable Case Temperature (°C) R thJC (DC) = 1.1 °C/ W 120 Conduction Period 100 60° 90° 120° 30° 180° DC 80 0 5 10 15 20 25 Average On-sta te Current (A) Fig. 2 - Current Rating Characteristics 12 16 20 Fig. 3 - On-State Power Loss Characteristics 130 90 8 Avera ge On-state Current (A) Average On-sta te Current (A) Fig. 1 - Current Rating Characteristics 110 4 30 35 DC 180° 120° 90° 60° 30° 30 25 20 RMS Limit 15 Conduction Period 10 5 T J = 125°C 0 0 5 10 15 20 25 30 Avera ge On-sta te Current (A) Fig. 4 - On-State Power Loss Characteristics Revision: 08-Jul-15 Document Number: 94383 3 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS...SPbF Series 350 Vishay Semiconductors 400 At Any Rated Load Condition And With Rated V RRM Applied Following Surge. Initial TJ = 125°C @60 Hz 0.0083 s @50 Hz 0.0100 s 300 Peak Half Sine Wa ve On-state Current (A) Pea k Half Sine Wave On-sta te Current (A) www.vishay.com 250 200 150 1 10 100 350 300 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Cond uc tion Ma y Not Be Ma inta ined. Initia l TJ = 125°C No Voltage Rea pp lied Rated VRRM Reapp lied 250 200 150 100 0.01 0.1 1 Pulse Train Duration (s) Number Of Equal Amplitude Half Cyc le Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current Instantaneous On-state Current (A) 1000 100 TJ= 25°C TJ= 125°C 10 1 0 1 2 3 4 5 Instantaneous On-state Voltage (V) Transient Thermal Imped anc e Z thJC (°C/W) Fig. 7 - On-State Voltage Drop Characteristics 10 Steady State Value (DC Opera tion) 1 0.1 D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Single Pulse 0.01 0.0001 0.001 0.01 0.1 1 10 Square Wave Pulse Duration (s) Fig. 8 - Gate Characteristics Revision: 08-Jul-15 Document Number: 94383 4 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-25TTS...SPbF Series www.vishay.com Vishay Semiconductors Rec tangular gate pulse a)Rec ommended load line for rated di/ dt: 10 V, 20 ohms tr = 0.5 µs, tp >= 6 µs b)Rec ommended load line for <= 30% rated d i/ dt: 10 V, 65 ohms 10 tr = 1 µs, tp >= 6 µs (1) (2) (3) (4) PGM = 40 W, tp = 1 ms PGM = 20 W, tp = 2 ms PGM = 8 W, tp = 5 ms PGM = 4 W, tp = 10 ms (a ) (b) VGD TJ = -10 °C TJ = 125 °C 1 TJ = 25 °C Instantaneous Gate Voltage (V) 100 (4) IGD (2) (3) (1) Frequency Limited by PG(AV) 0.1 0.001 0.01 0.1 1 10 100 Instantaneous Gate Current (A) Fig. 9 - Thermal Impedance ZthJC Characteristics ORDERING INFORMATION TABLE Device code VS- 25 T T S 12 S 1 2 3 4 5 6 7 1 - Vishay Semiconductors product 2 - Current rating (25 = 25 A) 3 - 4 - 5 - 6 - Circuit configuration: T = single thyristor Package: T = TO-220AC Type of silicon: S = standard recovery rectifier Voltage rating: voltage code x 100 = VRRM 7 - S = TO-220 D2PAK (SMD-220) version 8 - 9 - None = tube TRL = tape and reel (left oriented) TRR = tape and reel (right oriented) PbF = lead (Pb)-free TRL PbF 8 9 08 = 800 V 12 = 1200 V ORDERING INFORMATION (Example) PREFERRED P/N QUANTITY PER T/R MINIMUM ORDER QUANTITY PACKAGING DESCRIPTION VS-25TTS08SPbF 50 1000 Antistatic plastic tubes VS-25TTS08STRRPbF 800 800 13" diameter reel VS-25TTS08STRLPbF 800 800 13" diameter reel VS-25TTS12SPbF 50 1000 Antistatic plastic tubes VS-25TTS12STRRPbF 800 800 13" diameter reel VS-25TTS12STRLPbF 800 800 13" diameter reel LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com/doc?95046 Part marking information www.vishay.com/doc?95054 Packaging information www.vishay.com/doc?95032 Revision: 08-Jul-15 Document Number: 94383 5 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions www.vishay.com Vishay Semiconductors D2PAK DIMENSIONS in millimeters and inches Conforms to JEDEC® outline D2 PAK (SMD-220) (2)(3) E B Pad layout A A (E) c2 11.00 MIN. (0.43) A (3) L1 4 9.65 MIN. (0.38) (D1) (3) Detail A D H 1 2 17.90 (0.70) 15.00 (0.625) (2) 3 3.81 MIN. (0.15) L2 B B 2.32 MIN. (0.08) A 2 x b2 c 2.64 (0.103) 2.41 (0.096) (3) E1 C View A - A 2xb ± 0.004 M B 0.010 M A M B Plating Base Metal (4) b1, b3 H 2x e Gauge plane c1 (4) (c) B 0° to 8° Seating plane L3 Lead tip A1 L (b, b2) L4 Section B - B and C - C Scale: None Detail “A” Rotated 90 °CW Scale: 8:1 SYMBOL MILLIMETERS MIN. MAX. INCHES MIN. MAX. NOTES SYMBOL MILLIMETERS MIN. MAX. INCHES MIN. MAX. NOTES A 4.06 4.83 0.160 0.190 D1 6.86 8.00 0.270 0.315 3 A1 0.00 0.254 0.000 0.010 E 9.65 10.67 0.380 0.420 2, 3 E1 7.90 8.80 0.311 0.346 3 b 0.51 0.99 0.020 0.039 b1 0.51 0.89 0.020 0.035 b2 1.14 1.78 0.045 0.070 b3 1.14 1.73 0.045 0.068 c 0.38 0.74 0.015 0.029 c1 0.38 0.58 0.015 0.023 c2 1.14 1.65 0.045 0.065 D 8.51 9.65 0.335 0.380 4 e 2.54 BSC 0.100 BSC H 14.61 15.88 0.575 0.625 4 L 1.78 2.79 0.070 0.110 L1 - 1.65 - 0.066 4 L2 1.27 1.78 0.050 0.070 2 L4 L3 0.25 BSC 4.78 5.28 3 0.010 BSC 0.188 0.208 Notes (1) Dimensioning and tolerancing per ASME Y14.5 M-1994 (2) Dimension D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005") per side. These dimensions are measured at the outmost extremes of the plastic body (3) Thermal pad contour optional within dimension E, L1, D1 and E1 (4) Dimension b1 and c1 apply to base metal only (5) Datum A and B to be determined at datum plane H (6) Controlling dimension: inch (7) Outline conforms to JEDEC® outline TO-263AB Revision: 08-Jul-15 Document Number: 95046 1 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000