VS-110RKI...PbF, VS-111RKI...PbF Series Datasheet

VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
Phase Control Thyristors
(Stud Version), 110 A
FEATURES
• High current and high surge ratings
• Hermetic ceramic housing
• Designed and qualified for industrial level
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
TO-209AC (TO-94)
TYPICAL APPLICATIONS
• DC motor controls
• Controlled DC power supplies
PRODUCT SUMMARY
IT(AV)
110 A
VDRM/VRRM
400 V, 800 V, 1200 V
VTM
1.57 V
IGT
80 mA
TJ
-40 °C to 140 °C
Package
TO-209AC (TO-94)
Diode variation
Single SCR
• AC controllers








MAJOR RATINGS AND CHARACTERISTICS
PARAMETER
TEST CONDITIONS
IT(AV)
TC
IT(RMS)
VALUES
UNITS
110
A
90
°C
172
ITSM
I2t
50 Hz
2080
60 Hz
2180
50 Hz
21.7
60 Hz
19.8
VDRM/VRRM
Typical
tq
TJ
A
kA2s
400 to 1200
V
110
μs
-40 to 140
°C
IDRM/IRRM MAXIMUM
AT TJ = TJ MAXIMUM
mA
ELECTRICAL SPECIFICATIONS
VOLTAGE RATINGS
TYPE
NUMBER
VOLTAGE
CODE
VDRM/VRRM, MAXIMUM REPETITIVE
PEAK AND OFF-STATE VOLTAGE
V
VRSM, MAXIMUM NON-REPETITIVE
PEAK VOLTAGE
V
40
400
500
80
800
900
120
1200
1300
VS-110RKI
VS-111RKI
Revision: 11-Mar-14
20
Document Number: 94379
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Maximum average on-state current
at case temperature
Maximum RMS on-state current
Maximum peak, one-cycle
non-repetitive surge current
IT(AV)
IT(RMS)
ITSM
TEST CONDITIONS
180° conduction, half sine wave
172
t = 10 ms
t = 8.3 ms
t = 10 ms
Maximum
for fusing
I2t
No voltage
reapplied
2180
100 % VRRM 
reapplied
1830
No voltage
reapplied
Sinusoidal half wave,
initial TJ = TJ maximum
21.7
19.8
15.3
14.0
t = 0.1 ms to 10 ms, no voltage reapplied
217
Low level value of threshold voltage
VT(TO)1
(16.7 % x  x IT(AV) < I <  x IT(AV)), TJ = TJ maximum
0.82
High level value of threshold voltage
VT(TO)2
(I >  x IT(AV)), TJ = TJ maximum
1.02
Low level value of on-state slope resistance
rt1
(16.7 % x  x IT(AV) < I <  x IT(AV)), TJ = TJ maximum
2.16
High level value of on-state slope resistance
rt2
(I >  x IT(AV)), TJ = TJ maximum
1.70
Ipk = 350 A, TJ = TJ maximum, tp = 10 ms sine pulse
1.57
Maximum on-state voltage
VTM
Maximum holding current
IH
Typical latching current
IL
A
1750
100 % VRRM 
reapplied
t = 8.3 ms
I2t
°C
2080
t = 10 ms
I2t
A
90
t = 10 ms
t = 8.3 ms
UNITS
110
DC at 83 °C case temperature
t = 8.3 ms
Maximum I2t for fusing
VALUES
TJ = 25 °C, anode supply 6 V resistive load
200
400
kA2s
kA2s
V
m
V
mA
SWITCHING
PARAMETER
Maximum non-repetitive rate of
rise of turned-on current
SYMBOL
dI/dt
TEST CONDITIONS
Gate drive 20 V, 20 , tr  1 μs
TJ = TJ maximum, anode voltage  80 % VDRM
Typical delay time
td
Gate current 1 A, dIg/dt = 1 A/μs
Vd = 0.67 % VDRM, TJ = 25 °C
Typical turn-off time
tq
ITM = 50 A, TJ = TJ maximum, dI/dt = - 5 A/μs
VR = 50 V, dV/dt = 20 V/μs, gate 0 V 25 
VALUES
UNITS
300
A/μs
1
μs
110
BLOCKING
PARAMETER
SYMBOL
Maximum critical rate of rise of 
off-state voltage
dV/dt
Maximum peak reverse and 
off-state leakage current
IRRM,
IDRM
Revision: 11-Mar-14
TEST CONDITIONS
VALUES
UNITS
TJ = TJ maximum linear to 80 % rated VDRM
500
V/μs
TJ = TJ maximum rated VDRM/VRRM applied
20
mA
Document Number: 94379
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
TRIGGERING
PARAMETER
SYMBOL
Maximum peak gate power
PGM
Maximum average gate power
PG(AV)
Maximum peak positive gate current
IGM
Maximum peak positive gate voltage
+ VGM
Maximum peak negative gate voltage
- VGM
VALUES
TEST CONDITIONS
TYP.
TJ = TJ maximum, tp  5 ms
12
TJ = TJ maximum, f = 50 Hz, d% = 50
3.0
IGT
TJ = TJ maximum, tp  5 ms
TJ = 25 °C
TJ = 25 °C
TJ = 140 °C
DC gate current not to trigger
IGD
TJ = TJ maximum
DC gate voltage not to trigger
A
20
Maximum required gate
trigger/current/voltage are
the lowest value which will 
trigger all units 12 V anode
to cathode applied
TJ = - 40 °C
VGT
W
V
10
TJ = 140 °C
DC gate voltage required to trigger
UNITS
3.0
TJ = - 40 °C
DC gate current required to trigger
MAX.
VGD
Maximum gate current/
voltage not to trigger is the
maximum value which will
not trigger any unit with
rated VDRM anode to
cathode applied
180
-
80
120
40
-
2.5
-
1.6
2
1
-
mA
V
6.0
mA
0.25
V
THERMAL AND MECHANICAL SPECIFICATIONS
PARAMETER
SYMBOL
Maximum operating junction temperature range
Maximum storage temperature range
TEST CONDITIONS
VALUES
TJ
-40 to 140
TStg
-40 to 150
Maximum thermal resistance, junction to case
RthJC
DC operation
0.27
Maximum thermal resistance, case to heatsink
RthCS
Mounting surface, smooth, flat and greased
0.1
Non-lubricated threads
15.5
(137)
Lubricated threads
14
(120)
Mounting torque, ± 10 %
Approximate weight
130
Case style
See dimensions - link at the end of datasheet
UNITS
°C
K/W
N·m
(lbf · in)
g
TO-209AC (TO-94)
RthJC CONDUCTION
CONDUCTION ANGLE
SINUSOIDAL CONDUCTION
RECTANGULAR CONDUCTION
180°
0.043
0.031
120°
0.052
0.053
90°
0.066
0.071
60°
0.096
0.101
30°
0.167
0.169
TEST CONDITIONS
UNITS
TJ = TJ maximum
K/W
Note
• The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC
Revision: 11-Mar-14
Document Number: 94379
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
140
140
RthJC (DC) = 0.27 K/W
Maximum Allowable Case
Temperature (°C)
Maximum Allowable Case
Temperature (°C)
RthJC (DC) = 0.27 K/W
130
Ø
120
Conduction angle
110
100
120°
90
30°
60°
90°
130
120
Ø
Conduction period
110
100
DC
90
30°
180°
180°
90°
70
80
0
20
40
60
80
100
0
120
Average On-State Current (A)
94379_01
20
40
60
80
100 120 140 160 180
Average On-State Current (A)
94379_02
Fig. 1 - Current Ratings Characteristics
Fig. 2 - Current Ratings Characteristics
160
140
Ø
40
Conduction angle
20
TJ = 140 °C
/W
R
-Δ
60
W
80
W
W
1K
100
60
1.5
K/W
2 K/
W
40
4 K/W
80
20
0
K/
K/
RMS limit
6
K/
3
100
0.
0.8
120
0.
120
140
=
180°
120°
90°
60°
30°
SA
Maximum Average On-State
Power Loss (W)
160
R th
Maximum Average On-State
Power Loss (W)
120°
60°
80
5 K/W
0
0
20
40
60
80
100
120
Average On-State Current (A)
94379_03a
0
20
40
60
80
100
120
140
120
140
Maximum Allowable
Ambient Temperature (°C)
94379_03b
Fig. 3 - On-State Power Loss Characteristics
220
200
DC
180°
120°
90°
60°
30°
180
160
140
120
RMS limit
100
80
60
Ø
40
Conduction period
20
TJ = 140 °C
Maximum Average On-State
Power Loss (W)
Maximum Average On-State
Power Loss (W)
220
200
th
SA
160
=
0.
3
0.6
140
0.8
120
W
60
1.5 K
/W
2 K/W
40
4 K/W
80
20
K/
W
K/
K/
1K W
/W
100
0
-Δ
R
5 K/W
0
0
94379_04a
R
180
20
40
60
80
100 120 140 160 180
Average On-State Current (A)
0
20
94379_04b
40
60
80
100
Maximum Allowable
Ambient Temperature (°C)
Fig. 4 - On-State Power Loss Characteristics
Revision: 11-Mar-14
Document Number: 94379
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
2500
2000
Peak Half Sine Wave
On-State Current (A)
1800
1600
Peak Half Sine Wave
On-State Current (A)
At any rated load condition and with
rated VRRM applied following surge.
Initial TJ = 140 °C
at 60 Hz 0.0083 s
at 50 Hz 0.0100 s
1400
1200
Maximum non-repetitive surge current
versus pulse train duration. Control of
conduction may not be maintained.
Initial TJ = 140 °C
No voltage reapplied
Rated VRRM reapplied
2000
1500
1000
1000
800
1
10
500
0.01
100
Number of Equal Amplitude Half
Cycle Current Pulses (N)
94379_05
1
10
Pulse Train Duration (s)
94379_06
Fig. 5 - Maximum Non-Repetitive Surge Current
Instantaneous On-State Current (A)
0.1
Fig. 6 - Maximum Non-Repetitive Surge Current
10 000
TJ = 25 °C
1000
TJ = 140 °C
100
10
1
0
94379_07
1
2
3
4
5
Instantaneous On-State Voltage (V)
Fig. 7 - On-State Voltage Drop Characteristics
ZthJC - Transient Thermal
Impedance (K/W)
1
Steady state value
RthJC = 0.27 K/W
(DC operation)
0.1
0.01
0.001
0.0001
94379_08
0.001
0.01
0.1
1
10
Square Wave Pulse Duration (s)
Fig. 8 - Thermal Impedance ZthJC Characteristic
Revision: 11-Mar-14
Document Number: 94379
5
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-110RKI...PbF, VS-111RKI...PbF Series
www.vishay.com
Vishay Semiconductors
10
Rectangular gate pulse
(a) Recommended load line for
rated dI/dt: 20 V, 30 Ω,
tr ≤ 0.5 μs, tp ≥ 6 μs
(b) Recommended load line for
≤ 30 % rated dI/dt: 15 V, 40 Ω,
tr ≤ 1 μs, tp ≥ 6 μs
VGD
0.1
0.001
(b)
TJ = 40 °C
1
(1) PGM = 12 W, tp = 5 ms
(2) PGM = 30 W, tp = 2 ms
(3) PGM = 60 W, tp = 1 ms
(4) PGM = 200 W, tp = 300 μs
(a)
TJ = 25 °C
TJ = 140 °C
Instantaneous Gate Voltage (V)
100
(1)
(2)
(3)
(4)
Frequency limited by PG(AV)
IGD
0.01
0.1
1
10
100
1000
Instantaneous Gate Current (A)
94379_09
Fig. 9 - Gate Characteristics
ORDERING INFORMATION TABLE
Device code
VS-
11
0
RKI
120
PbF
1
2
3
4
5
6
-
Vishay Semiconductors product
2
-
IT(AV) rated average output current (rounded/10)
3
-
0 = Eyelet terminals (gate and auxiliary cathode leads)
4
-
1 = Fast-on terminals (gate and auxiliary cathode leads)
Thyristor
5
-
Voltage code x 10 = VRRM (see Voltage Ratings table)
6
-
1
None = Standard production
PbF = Lead (Pb)-free
LINKS TO RELATED DOCUMENTS
Dimensions
Revision: 11-Mar-14
www.vishay.com/doc?95003
Document Number: 94379
6
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Outline Dimensions
Vishay Semiconductors
TO-209AC (TO-94) for 110RKI and 111RKI Series
DIMENSIONS in millimeters (inches)
Ceramic housing
37
)M
IN
.
2.6 (0.10) MAX.
16.5 (0.65) MAX.
(0.
Ø 8.5 (0.33)
9 .5
Ø 4.3 (0.17)
Flexible lead
20 (0.79) MIN.
2
C.S. 16 mm
(0.025 s.i.)
C.S. 0.4 mm2
Red silicon rubber
(0.0006 s.i.)
Red cathode
157 (6.18)
170 (6.69)
White gate
215 ± 10
(8.46 ± 0.39)
Fast-on terminals
Red shrink
55 (2.16)
MIN.
White shrink
AMP. 280000-1
REF-250
Ø 22.5 (0.88) MAX.
24 (0.94)
MAX.
10 (0.39) MAX.
21 (0.83)
MAX.
SW 27
1/2"-20UNF-2A
29.5 (1.16) MAX.
Note
• For metric device: M12 x 1.75 contact factory
Document Number: 95363
Revision: 25-Sep-08
For technical questions, contact: [email protected]
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000