VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series Datasheet

VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
www.vishay.com
Vishay Semiconductors
Phase Control Thyristors
(Stud Version), 80 A
FEATURES
• Hermetic glass-metal seal
• International standard case TO-209AC (TO-94)
• Designed and qualified for industrial level
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
TO-209AC (TO-94)
TYPICAL APPLICATIONS
• DC motor controls
PRODUCT SUMMARY
• Controlled DC power supplies
IT(AV)
80 A
VDRM/VRRM
400 V, 800 V, 1200 V
VTM
1.60 V
IGT
120 mA
• AC controllers
TJ
-40 °C to 125 °C
Package
TO-209AC (TO-94)
Diode variation
Single SCR







MAJOR RATINGS AND CHARACTERISTICS
PARAMETER
TEST CONDITIONS
IT(AV)
TC
VALUES
UNITS
80
A
85
°C
125
IT(RMS)
ITSM
I2t
50 Hz
1900
60 Hz
1990
50 Hz
18
60 Hz
16
VDRM/VRRM
Typical
tq
TJ
A
kA2s
400 to 1200
V
110
μs
-40 to 125
°C
IDRM/IRRM MAXIMUM
AT TJ = 125 °C
mA
ELECTRICAL SPECIFICATIONS
VOLTAGE RATINGS
TYPE NUMBER
VS-80RIA
VS-81RIA
VOLTAGE
CODE
VDRM/VRRM, MAXIMUM REPETITIVE
PEAK AND OFF-STATE VOLTAGE
V
VRSM, MAXIMUM NON-REPETITIVE
PEAK VOLTAGE
V
40
400
500
80
800
900
120
1200
1300
15
Revision: 11-Mar-14
Document Number: 94392
1
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Maximum average on-state current
at case temperature
Maximum RMS on-state current
Maximum peak, one-cycle
non-repetitive surge current
IT(AV)
IT(RMS)
ITSM
TEST CONDITIONS
180° conduction, half sine wave
125
No voltage
reapplied
100 % VRRM
reapplied
1600
t = 10 ms
t = 8.3 ms
t = 10 ms
Maximum
for fusing
I2t
1990
Sinusoidal half wave,
initial TJ = TJ maximum
No voltage
18
16
12.7
t = 0.1 ms to 10 ms, no voltage reapplied
180.5
VT(TO)1
(16.7 % x  x IT(AV) < I <  x IT(AV)), TJ = TJ maximum
0.99
High level value of threshold voltage
VT(TO)2
(I >  x IT(AV)), TJ = TJ maximum
1.13
Low level value of on-state slope resistance
rt1
(16.7 % x  x IT(AV) < I <  x IT(AV)), TJ = TJ maximum
2.29
High level value of on-state slope resistance
rt2
(I >  x IT(AV)), TJ = TJ maximum
1.84
Ipk = 250 A, TJ = 25 °C, tp = 10 ms sine pulse
1.60
VTM
Maximum holding current
IH
Typical latching current
IL
TJ = 25 °C, anode supply 12 V resistive load
kA2s
11.7
Low level value of threshold voltage
Maximum on-state voltage
A
1675
100 % VRRM 
reapplied
t = 8.3 ms
I2t
°C
1900
t = 10 ms
I2t
A
85
t = 10 ms
t = 8.3 ms
UNITS
80
DC at 75 °C case temperature
t = 8.3 ms
Maximum I2t for fusing
VALUES
200
400
kA2s
V
m
V
mA
SWITCHING
PARAMETER
Maximum non-repetitive rate of
rise of turned-on current
SYMBOL
dI/dt
TEST CONDITIONS
TJ = 125 °C, Vd = Rated VDRM, ITM = 2 x dI/dt snubber
0.2 μF, 15 , gate pulse: 20 V, 65 , tp = 6 μs, tr = 0.5 μs
Per JEDEC standard RS-397, 5.2.2.6.
VALUES
UNITS
300
A/μs
Typical delay time
td
Gate pulse: 10 V, 15  source, tp = 6 μs, tr = 0.1 μs,
Vd = Rated VDRM, ITM = 50 Adc, TJ = 25 °C
Typical turn-off time
tq
ITM = 50 A, TJ = TJ maximum, dI/dt = - 5 A/μs, VR = 50 V,
dV/dt = 20 V/μs, gate bias: 0 V 25 , tp = 500 μs
110
SYMBOL
TEST CONDITIONS
VALUES
UNITS
1
μs
BLOCKING
PARAMETER
Maximum critical rate of rise of 
off-state voltage
dV/dt
TJ = 125 °C exponential to 67 % rated VDRM
500
V/μs
Maximum peak reverse and 
off-state leakage current
IRRM,
IDRM
TJ = 125 °C rated VDRM/VRRM applied
15
mA
Revision: 11-Mar-14
Document Number: 94392
2
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
www.vishay.com
Vishay Semiconductors
TRIGGERING
PARAMETER
SYMBOL
Maximum peak gate power
PGM
Maximum average gate power
PG(AV)
Maximum peak positive gate current
IGM
Maximum peak positive gate voltage
+ VGM
Maximum peak negative gate voltage
- VGM
TEST CONDITIONS
VALUES
TJ = TJ maximum, tp  5 ms
12
TJ = TJ maximum, f = 50 Hz, d% = 50
3
TJ = TJ maximum, tp  5 ms
20
3
10
TJ = - 40 °C
Maximum DC gate current required to trigger
IGT
120
Maximum required gate trigger/
current/voltage are the lowest value
which will trigger all units 6 V anode
to cathode applied
TJ = 125 °C
VGT
DC gate current not to trigger
A
V
60
TJ = 25 °C
2.5
1.5
Maximum gate current/voltage not to
trigger is the maximum value which
will not trigger any unit with rated
VDRM anode to cathode applied
TJ = TJ maximum
VGD
mA
3.5
TJ = 125 °C
IGD
DC gate voltage not to trigger
W
270
TJ = 25 °C
TJ = - 40 °C
Maximum DC gate voltage required to trigger
UNITS
V
6
mA
0.25
V
VALUES
UNITS
THERMAL AND MECHANICAL SPECIFICATIONS
PARAMETER
SYMBOL
Maximum operating junction 
temperature range
TEST CONDITIONS
TJ
- 40 to 125
Maximum storage temperature range
TStg
- 40 to 150
Maximum thermal resistance, 
junction to case
RthJC
DC operation
0.30
Maximum thermal resistance, 
case to heatsink
RthCS
Mounting surface, smooth, flat and greased
0.1
°C
K/W
Non-lubricated threads
15.5
(137)
Lubricated threads
14
(120)
Mounting torque, ± 10 %
Approximate weight
130
Case style
See dimensions - link at the end of datasheet
N·m
(lbf · in)
g
TO-209AC (TO-94)
RthJC CONDUCTION
CONDUCTION ANGLE
SINUSOIDAL CONDUCTION
RECTANGULAR CONDUCTION
180°
0.042
0.030
120°
0.050
0.052
90°
0.064
0.070
60°
0.095
0.100
30°
0.164
0.165
TEST CONDITIONS
UNITS
TJ = TJ maximum
K/W
Note
• The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC
Revision: 11-Mar-14
Document Number: 94392
3
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
Vishay Semiconductors
Maximum Allowable Case Temperature (°C)
Maximum Allowable Case Temperature (°C)
www.vishay.com
130
80RIA Series
RthJC (DC) = 0.30 K/W
120
110
Conduc tion Angle
100
30°
60°
90°
120°
90
180°
80
0
10 20
30 40
50 60 70
80 90
130
80RIA Series
RthJC (DC) = 0.30 K/W
120
110
Conduction Period
100
90
30°
80
120°
180°
DC
70
0
20
40
60
80
100
120
140
Average On-state Current (A)
Average On-state Current (A)
Fig. 1 - Current Ratings Characteristics
Fig. 2 - Current Ratings Characteristics
120
e lt
-D
K/
W
a
R
1.4
K/
W
RMSLimit
60
/W
4K
0.
70
1
=
80
A
90
W
K/
100
hS
R t
180°
120°
90°
60°
30°
110
6
0.
Maximum Average On-state Power Loss (W)
60°
90°
2K
/W
50
40
Conduction Angle
3 K/
30
20
10
W
5 K/ W
80RIA Series
TJ = 125°C
0
0
10
20
30
40
50
60
70
80
0
Average On-state Current (A)
25
50
75
100
125
Maximum Allowable Ambient Temperature (°C)
Maximum Average On-state Power Loss (W)
Fig. 3 - On-State Power Loss Characteristics
180
DC
180°
120°
90°
60°
30°
160
140
120
R
th
SA
100
80
=
0.
6K
/W
0.
4
K/
W
-D
e lt
a
1K
/W
RMSLimit
Conduc tion Period
60
40
80RIA Series
TJ = 125°C
20
R
1.4
K/ W
2 K/
W
3 K/ W
5 K/ W
0
0
20
40
60
80
100
120
Average On-state Current (A)
140
0
25
50
75
100
125
Maximum Allowable Ambient Temperature (°C)
Fig. 4 - On-State Power Loss Characteristics
Revision: 11-Mar-14
Document Number: 94392
4
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
1800
Vishay Semiconductors
Peak Half Sine Wave On-state Current (A)
Peak Half Sine Wave On-state Current (A)
www.vishay.com
At Any Rated Load Condition And With
Rated VRRM Applied Following Surge.
Initial TJ = 125°C
at 60 Hz 0.0083 s
at 50 Hz 0.0100 s
1600
1400
1200
1000
80RIA Series
800
1
10
100
2000
Maximum Non Repetitive Surge Current
1900
Versus Pulse Train Duration. Control
1800 Of Conduction May Not Be Maintained.
Initial TJ = 125°C
1700
No Voltage Reapplied
1600
Rated VRRM Reapplied
1500
1400
1300
1200
1100
1000
900
80RIA Series
800
700
0.01
0.1
1
Pulse Train Duration (s)
Number Of Equa l Amplitude Half Cycle Current Pulses (N)
Fig. 5 - Maximum Non-Repetitive Surge Current
Fig. 6 - Maximum Non-Repetitive Surge Current
Instantaneous On-state Current (A)
10000
1000
100
TJ = 25°C
TJ = 125°C
10
80RIA Series
1
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Instantaneous On-state Voltage (V)
1
Steady State Value
R thJC = 0.30 K/W
Transient Thermal Impedance Z
thJC
(K/ W)
Fig. 7 - On-State Voltage Drop Characteristics
(DC Operation)
0.1
0.01
80RIA Series
0.001
0.0001
0.001
0.01
0.1
1
10
Sq uare Wave Pulse Duration (s)
Fig. 8 - Thermal Impedance ZthJC Characteristics
Revision: 11-Mar-14
Document Number: 94392
5
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VS-80RIA...PbF, VS-81RIA...PbF, VS-82RIA...PbF Series
www.vishay.com
Vishay Semiconductors
Rectangular gate pulse
a) Recommended load line for
rated di/dt : 20V, 30ohms; tr<=0.5 µs
b) Recommended load line for
<=30% rated di/dt : 20V, 65ohms
10
tr<=1 µs
1
VGD
(1) (2)
(a)
(3) (4)
(b)
IGD
0.1
0.001
(1) PGM = 100W, tp = 500µs
(2) PGM = 50W, tp = 1ms
(3) PGM = 20W, tp = 2.5ms
(4) PGM = 10W, tp = 5ms
Tj=-40 °C
Tj=25 °C
Tj=125 °C
Instantaneous Gate Voltage (V)
100
Frequency Limited by PG(AV)
Device: 80RIA Series
0.01
0.1
1
10
100
1000
Instantaneous Gate Current (A)
Fig. 9 - Gate Characteristics
ORDERING INFORMATION TABLE
Device code
VS-
8
0
RIA
120
M
PbF
1
2
3
4
5
6
7
1
-
Vishay Semiconductors product
2
-
ITAV x 10 A
3
-
0 = Eyelet terminals (gate and auxiliary cathode leads)
1 = Fast-on terminals (gate and auxiliary cathode leads)
2 = Flag terminals (gate and auxiliary cathode terminals)
4
-
RIA = Essential part number
5
-
Voltage code x 100 = VRRM (see Voltage Ratings table)
6
-
None = Stud base 1/2"-20UNF- 2 A threads
M = Stud base metric threads M12 x 1.75 E 6
7
-
None = Standard production
-
PbF = Lead (Pb)-free
LINKS TO RELATED DOCUMENTS
Dimensions
www.vishay.com/doc?95362
Revision: 11-Mar-14
Document Number: 94392
6
For technical questions within your region: [email protected], [email protected], [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Outline Dimensions
Vishay Semiconductors
TO-209AC (TO-94) for 80RIA Series
DIMENSIONS in millimeters (inches)
Glass metal seal
37
)M
IN
.
2.5 (0.10) MAX.
16.5 (0.65) MAX.
(0.
Ø 8.5 (0.33)
9 .5
Ø 4.3 (0.17)
Flexible lead
20 (0.79) MIN.
C.S. 16 mm2
(0.025 s.i.)
C.S. 0.4 mm2
Red silicon rubber
(0.0006 s.i.)
Red cathode
157 (6.18)
170 (6.69)
White gate
215 ± 10
(8.46 ± 0.39)
Fast-on terminals
Red shrink
55 (2.17)
MIN.
White shrink
AMP. 280000-1
REF-250
Ø 23.5 (0.92) MAX.
24 (0.94)
MAX.
10.0 (0.39) MAX.
21 (0.83)
MAX.
SW 27
1/2"-20UNF-2A
29.5 (1.16) MAX.
Document Number: 95362
Revision: 17-Sep-10
For technical questions, contact: [email protected]
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000