PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIFFERENTIAL LOW POWER TC & VCTCXO MHz SERIES „DTCVCTO“ 1.0—220 MHz FEATURES APPLICATIONS + + + + + + + + + + + + + 100% pin-to-pin drop-in replacement to quartz and MEMS based XO Ultra Performance Oscillator for Low Cost TCXO function activated when Pin 1 is not connected Excellent long time reliability—outperforms quartz-based XO Excellent jitter performance Very tight frequency stability as low as ±2.5 ppm Outstanding long term aging Industry-standard packages: 3.2x2.5; 5.0x3.2; 7.0x5.0 mm Pb-free, RoHS and REACH compliant / MSL1@260°C PARAMETER AND CONDITIONS SYMBOL SATA, SAS, 10GB Ethernet, Fibre Channel, PCI-Express Networking, broadband, instrumentation Telecom etc. MIN. TYP. MAX. UNIT 2.97 3.3 3.63 V 2.25 2.5 2.75 V 2.25 – 3.63 V 1 – 220 MHz CONDITION LVPECL AND LVDS, COMMON ELECTRICAL CHARACTERISTICS Supply Voltage Output Frequency Range VDD f Termination schemes in Figures 1 and 2 - XX ordering code Initial Tolerance F_init -2 – 2 PPM At 25°C Stability Over Temperature F_stab -2.5 – +2.5 PPM -5 – +5 PPM Over operating temperature range at rated nominal power supply voltage and load. Supply Voltage F_VDD – 50 – PPB ±10% VDD (±5% for VDD = 1.8V) Output Load F_load – 0.1 – PPM 15 pF ±10% of load First Year Aging F_aging1 -2 – +2 PPM 25°C 10-year Aging F_aging10 -5 – +5 PPM 25°C T_use -40 – +85 °C Industrial -20 – +70 °C Extended Commercial -65 – +150 °C Operating Temperature Range Storage Temperature Range Pull Range T_stor PR ±12.5, ±25, ±50 PPM Upper Control Voltage VC_U VDD-0.1 – – V Control Voltage Range VC_L – – 0,1 V Control Voltage Input Impedance Z_vc 100 – – k 8 kHz Frequency Change Polarity Control Voltage -3dB Bandwidth – Positive slope All VDDs. Voltage at which maximum deviation is guaranteed. – V_BW – – Input Voltage High VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedance Z_in – 100 250 kΩ Pin 1, OE logic high or logic low, or ST logic high 2 – – MΩ Pin 1, ST logic low Start-up Time T_start – 6 10 ms Measured from the time VDD reaches its rated minimum value. Resume Time T_resume – 6 10 ms In Standby mode, measured from the time ST pin crosses 50% threshold. DC 45 – 55 % Contact PETERMANN-TECHNIK for tighter duty cycle Duty Cycle CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION LVPECL, DC AND AC CHARACTERISTICS Current Consumption IDD – 61 69 mA Excluding Load Termination Current, VDD = 3.3V or 2.5V I_OE – – 35 mA OE = Low Output Disable Leakage Current I_leak – – 1 µA OE = Low Standby Current I_std – – 100 µA ST = Low, for all VDDs I_driver – – 30 mA Maximum average current drawn from OUT+ or OUT- Output High Voltage VOH VDD-1.1 – VDD-0.7 V See Figure 1(a) Output Low Voltage VOL VDD-1.9 – VDD-1.5 V See Figure 1(a) V_Swing 1.2 1.6 2.0 V See Figure 1(b) Rise/Fall Time Tr, Tf – 300 500 ps 20% to 80%, see Figure 1(a) OE Enable/Disable Time T_oe – – 115 ns f = 212.5 MHz - For other frequencies, T_oe = 100ns + 3 period RMS Period Jitter T_jitt – 1.2 1.7 ps f = 100 MHz, VDD = 3.3V or 2.5V – 1.2 1.7 ps f = 156.25 MHz, VDD = 3.3V or 2.5V – 1.2 1.7 ps f = 212.5 MHz, VDD = 3.3V or 2.5V T_phj – 0.6 0.85 ps f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all VDDs OE Disable Supply Current Maximum Output Current Output Differential Voltage Swing RMS Phase Jitter (random) LVDS, DC AND AC CHARACTERISTICS Current Consumption IDD – 47 55 mA Excluding Load Termination Current, VDD = 3.3V or 2.5V OE Disable Supply Current I_OE – – 35 mA OE = Low Differential Output Voltage VOD 250 350 450 mV See Figure 2 Output Disable Leakage Current I_leak – – 1 µA OE = Low Standby Current I_std – – 100 µA ST = Low, for all VDDs VOD Magnitude Change VOD – – 50 mV See Figure 2 VOS 1.125 1.2 1.375 V See Figure 2 VOS Magnitude Change VOS – – 50 mV See Figure 2 Rise/Fall Time Tr, Tf – 495 600 ps 20% to 80%, see Figure 2 OE Enable/Disable Time T_oe – – 115 ns f = 212.5 MHz - For other frequencies, T_oe = 100ns + 3 period RMS Period Jitter T_jitt – 1.2 1.7 ps f = 100 MHz, VDD = 3.3V or 2.5V – 1.2 1.7 ps f = 156.25 MHz, VDD = 3.3V or 2.5V – 1.2 1.7 ps f = 212.5 MHz, VDD = 3.3V or 2.5V – 0.6 0.85 ps f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz, all VDDs Offset Voltage RMS Phase Jitter (random) T_phj EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance: 10.000 g Vibration Resistance: 70 g PIN DESCRIPTION PIN SYMBOL TOP VIEW FUNCTIONALITY VC V control OE Input 1 Voltage control VC/OE/ST/NC 1 6 VDD NC 2 5 OUT- GND 3 4 OUT+ H or Open: specified frequency output L: output is high impedance H or Open: specified frequency output ST Input 2 NC NA 3 GND Power VDD Power Supply Ground 4 OUT+ Output Oscillator output 5 OUT- Output Complementary oscillator output 6 VDD Power Power supply voltage L: Device goes to sleep mode. Supply current reduces to No Connect; Leave it floating or connect to GND for better heat dissipation CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com WAVE FORM DIAGRAMS FIGURE 1(A). LVPECL VOLTAGE LEVELS PER DIFFERENTIAL PIN (OUT+/OUT-) OUT80% 80% 20% VOH 20% OUT+ Tr VOL Tf GND FIGURE 1(B). LVPECL VOLTAGE LEVELS ACROSS DIFFERENTIAL PAIR V_ Swing 0V t FIGURE 2. LVDS VOLTAGE LEVELS PER DIFFERENTIAL PIN (OUT+/OUT-) OUT80% 80% VOD 20% 20% OUT+ VOS Tr Tf GND CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS LVPECL: FIGURE 3. LVPECL TYPICAL TERMINATION VDD OUT+ Z0 = 50 Ω D+ LVPECL Driver Receiver Device OUT- Z0 = 50 Ω D50 Ω 50 Ω VTT = VDD - 2.0 FIGURE 4. LVPECL AC COUPLED TERMINATION VDD= 3.3V => R1 = 100 to 150 Ω VDD= 2.5V => R1 = 75 Ω VDD OUT+ D+ Z0 = 50 Ω 100nF Receiver Device LVPECL Driver 100nF OUT- Z0 = 50 Ω R1 R1 D50 Ω 50 Ω VTT FIGURE 5. LVPECL WITH THEVENIN TYPICAL TERMINATION VDD = 3.3V => R1 = R3 = 133 Ω and R2 = R4 = 82 Ω VDD = 2.5V => R1 = R3 = 250 Ω and R2 = R4 = 62.5 Ω VDD OUT+ VDD R1 R3 Z0 = 50 Ω D+ LVPECL Driver OUT- Receiver Device Z0 = 50 Ω DR2 CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS R4 PAGE 4 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TERMINATION DIAGRAMS LVDS: FIGURE 6. LVDS SINGLE TERMINATION (LOAD TERMINATED) VDD OUT+ Z0 = 50 Ω 100 Ω LVDS Driver OUT- D+ Z0 = 50 Ω Receiver Device D- REFLOW SOLDER PROFILE CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2X 2.5 X 0.75 MM #2 #6 #5 #4 #1 #2 #3 1.00 1.6 #3 0.6 0.65 0.75±0.05 #1 2.25 2.2 #4 0.7 #5 0.9 3.2±0.05 2.5±0.05 #6 1.05 RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0X 3.2 X 0.75 MM #2 #5 #4 #1 #2 #3 #3 1.20 2.20 #6 0.64 0.90 0.75±0.05 #1 2.54 2.54 #4 0.9 #5 1.2 5.0±0.10 3.2±0.10 #6 RECOMMENDED LAND PATTERN (UNIT:MM) [1] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0X 5.0 X 0.90 MM #2 #5 #4 #1 #2 #3 3.80 #6 #3 1.40 0.90±0.10 #1 5.08 5.08 #4 1.60 1.10 #5 2.6 7.0±0.10 5.0±0.10 #6 1.60 Note: 1. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION FREQUENCY 1.000000 MHz to 220.000000 MHz OSCILLATOR FAMILY DTCVCTO SUPPLY VOLTAGE “25“ for 2.5V “33“ for 3.3V “XX“ for 2.25V to 3.63V SIGNALING TYPE “1” = LVPECL “2” = LVDS TEMPERATURE RANGE “M” for -20 +70°C “W” for -40 +85°C DTCVCTO33-3225-E0-2.5-M-220.000MHz-T-1 FREQUENCY STABILITY PACKAGE SIZE “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm FEATURE PIN(PIN 1) PACKING METHOD “B“ for Bulks or Tubes “T” for Tape & Reel “2.5” for ±2.5 PPM “5.0” for ±5.0 PPM “V” for Voltage Control “E” for Output Enable “S” for Standby “N” for No Connect “O” for FIXED FREQUENCY PULL RANGE OPTIONS “VQ” for ±12.5 PPM “VM” for ±25 PPM “VB” for ±50 PPM EXAMPLE: DTCVCTO33-3225-E0-2.5-M-220.000MHz-T-1 PLEASE INDICATE YOUR REQUIRED PARAMETERS SAMPLES ARE AVAILABLE WITHIN A SHORT DELIVERY PERIOD! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 8 OF 8 I SPEC 01 I REV.00 I NOVEMBER 2014