PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com HIGH FREQUENCY ULTRA PERFORMANCE OSCILLATOR SERIES „HFUPO“ 80.0-220.0MHz FEATURES APPLICATIONS + + + + + + + + + + SATA, SAS, Ethernet, 10-Gigabit Ethernet, SONET, PCI Express, video, Ultra Performance Oscillator for Low Cost Wireles Low power consumption / Ultra low phase Jitter + Computing, storage, networking, telecom, industrial control, + etc. Excellent long time reliability Very tight frequency stability as low as ±10 ppm Outstanding long term aging of ±5ppm after 10 years LVCMOS/LVTTL compatible output Standard housings: 2.5x2.0; 3.2x2.5; 5.0x3.2; 7.0x5.0mm Express samples within 1 day ex works PETERMANN-TECHNIK Pb-free, RoHS and REACH compliant / MSL1@260°C GENERAL DATA[1] PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT CONDITION FREQUENCY RANGE Output Frequency Range f 80.000001 F_stab -10 – 220 MHz – +10 PPM Inclusive of initial tolerance at 25 °C, and variations over -20 – +20 PPM operating temperature, rated power supply voltage and load -25 – +25 PPM -50 – +50 PPM -1.5 – +1.5 PPM 25°C -5 – +5 PPM 25°C -20 – +70 °C Extended Commercial FREQUENCY STABILITY AND AGING Frequency Stability First year Aging F_aging 10-year Aging OPERATING TEMPERATURE RANGE Operating Temperature Range T_use -40 – +85 °C Industrial Storage Temperature Range T_stor -55 – +125 °C Storage VDD 1.71 1.8 1.89 V Supply voltages between 2.5V and 3.3V can be supported. 2.25 2.5 2.75 V Contact PETERMANN-TECHNIK for guaranteed performance 2.52 2.8 3.08 V specs for supply voltages not specified in this table 2.97 3.3 3.63 V – 34 36 mA No load condition, f = 100 MHz, VDD = 2.5V, 2.8V or 3.3V – 30 33 mA No load condition, f = 100 MHz, VDD = 1.8V – – 31 mA VDD = 2.5V, 2.8V or 3.3V, OE = GND, output is pulled down 30 mA VDD = 1.8 V. OE = GND, output is pulled down SUPPLY VOLTAGE AND CURRENT CONSUMPTION Supply Voltage Current Consumption OE Disable Current Standby Current IDD I_OD I_std – – 70 µA VDD = 2.5V, 2.8V or 3.3V, ST = GND, output is pulled down – – 10 µA VDD = 1.8 V. ST = GND, output is pulled down Note: 1. All electrical specifications in the above table are specified with 15 pF±10% output load at default drive strength and for all VDD(s) unless otherwise stated. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 1 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com GENERAL DATA[1] (continued) PARAMETER AND CONDITIONS SYMBOL MIN. TYP. MAX. UNIT DC 45 – 55 % f <= 165 MHz, all VDDs. CONDITION LVCMOS OUTPUT CHARACTERISTICS Duty Cycle 40 – 60 % f > 165 MHz, all VDDs. Rise/Fall Time Tr, Tf – 1.2 2 ns 15 pF load, 10% - 90% VDD Output Voltage High VOH 90% – – VDD IOH = -6 mA, IOL = 6 mA, (VDD = 3.3V, 2.8V, 2.5V), IOL = 3 mA, (VDD = 1.8V) Output Voltage Low VOL – – 10% VDD Input Voltage High VIH 70% – – VDD Pin 1, OE or ST Input Voltage Low VIL – – 30% VDD Pin 1, OE or ST Input Pull-up Impedance Z_in – 100 250 kΩ Pin 1, OE logic high or logic low, or ST logic high 2 – – MΩ Pin 1, ST logic low T_start – 7 10 ms Measured from the time VDD reaches its rated minimum value T_oe – – 115 ns f = 80 MHz, For other frequencies, T_oe = 100 ns + 3 cycles T_resume – – 10 ms In standby mode, measured from the time ST pin crosses 50% threshold. Refer to Figure 4. T_jitt – 1.5 2 ps f = 156.25 MHz, VDD = 2.5V, 2.8V or 3.3V – 2 3 ps f = 156.25 MHz, VDD = 1.8V – 0.5 1 ps f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz INPUT CHARACTERISTICS STARTUP AND RESUME TIMING Startup Time OE Enable/Disable Time Resume Time JITTER RMS Period Jitter RMS Phase Jitter (random) T_phj EXCELLENT RELIABILITY DATA MTBF 500 million hours Shock Resistance: 10.000 g Vibration Resistance: 70 g Note: 1. All electrical specifications in the above table are specified with 15 pF ±10% output load and for all VDD(s) unless otherwise stated. PIN DESCRIPTION PIN SYMBOL FUNCTIONALITY Output Enable 1 TOP VIEW OE/ ST Standby H or Open[2]: specified frequency output L: output is high impedance. Only output driver is disabled. H or Open[2]: specified frequency output L: output is low (weak pull down). Device goes to sleep mode. Supply current reduces to I_std. 2 GND Power Electrical ground[3] 3 OUT Output Oscillator output 4 VDD Power Power supply voltage[3] OE/ST 1 4 VDD GND 2 3 OUT Notes: 2. A pull-up resistor of <10 kΩ between OE/ ST pin and VDD is recommended in high noise environment. 3. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 2 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com TEST CIRCUIT AND WAVEFORM [4, 5] FIGURE 1. TEST CIRCUIT FIGURE 2. WAVEFORM Vout Vdd 3 4 Power Supply Test Point tf 90%Vdd 0.1µF 15pF (including probe and fixture capacitance) 2 1 tr 50% 10%Vdd High Pulse (TH) Low Pulse (TL) Period Vdd OE/ST Function 1kΩ TIMING DIAGRAMS [6, 7] FIGURE 3. STARTUP TIMING (OE/ST MODE) 90%Vdd, 2.5/2.8/3.3V devices Vdd 95%Vdd, 1.8V devices Pin 4 Voltage FIGURE 4. STANDBY RESUME TIMING (ST MODE ONLY) 50%Vdd No Glitch first cycle Vdd ST Voltage T_resume T_start CLK Output T_start: Time to start from power-off FIGURE 5. OE ENABLE TIMING (OE MODE ONLY) CLK Output T_resume: Time to resume from ST FIGURE 6. OE DISABLE TIMING (OE MODE ONLY) Vdd 50%Vdd Vdd OE Voltage OE Voltage 50%Vdd T_OE CLK Output CLK Output T_OE HZ T_OE: Time to re-enable the clock output T_OE: Time to put the output drive in High Z mode Notes: 4. Duty Cycle is computed as Duty Cycle = TH/Period. 5. HFUPO supports the configurable duty cycle feature. For custom duty cycle at any given frequency, contact PETERMANN-TECHNIK. 6. HFUPO supports no runt pulses and no glitches during startup or resume. 7. HFUPO supports gated output which is accurate within rated frequency stability from the first cycle. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 3 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 2.7X 2.4 X 0.75 MM (100% COMPATIBLE WITH 2.5X2.0MM FOOTPRINT) #1 1.9 1.00 #3 #3 #1 #2 #2 1.0 1.1 1.5 #4 0.5 2.7±0.05 2.4±0.05 #4 1.1 0.75±0.05 0.85 RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 3.2 X 2.5 X 0.75 MM #1 2.2 2.1 #3 #3 #1 #2 #2 1.2 0.9 1.9 #4 0.7 3.2±0.05 2.5±0.05 #4 1.4 0.75±0.05 0.9 RECOMMENDED LAND PATTERN (UNIT:MM) [9] PACKAGE SIZE – DIMENSIONS (UNIT:MM) 5.0 X 3.2 X 0.75 MM #3 #1 #2 #2 1.1 1.6 2.2 #4 1.15 1.5 0.75±0.05 #1 2.54 2.39 #3 0.8 5.0±0.05 3.2±0.05 #4 Note: 8. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 4 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com DIMENSIONS AND PATTERNS RECOMMENDED LAND PATTERN (UNIT:MM) PACKAGE SIZE – DIMENSIONS (UNIT:MM) 7.0 X 5.0 X 0.90 MM #3 #1 #2 3.81 #4 #2 2.0 1.1 1.4 2.2 0.90±0.10 #1 5.08 5.08 #3 2.6 7.0±0.05 5.0±0.05 #4 REFLOW SOLDER PROFILE Note: 8. A capacitor value of 0.1 µF between VDD and GND is recommended. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 5 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com ORDERING INFORMATION OSCILLATOR FAMILY SUPPLY VOLTAGE “18“ “25“ “28“ “33“ HFUPO for 1.8V for 2.5V for 2.8V for 3.3V TEMPERATURE RANGE FREQUENCY 80.0000001 to 220.000000 MHz “M” for -20 +70°C “W” for -40 +85°C HFUPO 33-2724-E-10-M-90.000MHz-T FREQUENCY STABILITY “10” for ±10 PPM “20” for ±20 PPM “25” for ±25 PPM “50” for ±50 PPM PACKAGE SIZE “2724” for 2.5 X 2.0 mm “3225” for 3.2 X 2.5 mm “5032” for 5.0 X 3.2 mm “7050” for 7.0 X 5.0 mm PACKING METHOD “B” for BULKS or TUBES “T” for TAPE & REEL FEATURE PIN 1 “E” for OUTPUT ENABLE “S” for STANDBY Note: 9. Contact PETERMANN-TECHNIK for custom drive strength to drive higher or multiple load, or for EMI reduction. EXAMPLE: HFUPO33-2724-E-10-M-90.000MHz-T PLEASE INDICATE YOUR REQUIRED PARAMETERS EXPRESS SAMPLES ARE DELIVERABLE ON THE SAME DAY IF ORDERED UNTIL 02:00 PM! CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 6 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014 PETERMANN-TECHNIK GmbH Lechwiesenstr. 13 ∙ D-86899 ∙ Landsberg am Lech Tel: +49/8191/305395 ∙ Fax: +49/8191/305397 [email protected] ∙ www.petermann-technik.com PREMIUM QUALITY BY PETERMANN-TECHNIK OUR COMPANY IS CERTIFIED ACCORDING TO ISO 9001:2008 IN OCTOBER 2013 BY THE DMSZ CERTIFIKATION GMBH. THIS IS FOR YOU TO ENSURE THAT THE PRINCIPLES OF QUALITY MANAGEMENT ARE FULLY IMPLEMENTED IN OUR QUALITY MANAGEMENT SYSTEM AND QUALITY CONTROL METHODS ALSO DOMINATE OUR QUALITY STANDARDS. © PETERMANN-TECHNIK GmbH 2014. The information contained herein is subject to change at any time without notice. PETERMANN-TECHNIK owns all rights, title and interest to the intellectual property related to PETERMANN-TECHNIK's products, including any software, firmware, copyright, patent, or trademark. The sale of PETERMANN-TECHNIK products does not convey or imply any license under patent or other rights. PETERMANNTECHNIK retains the copyright and trademark rights in all documents, catalogs and plans supplied pursuant to or ancillary to the sale of products or services by PETERMANN-TECHNIK. Unless otherwise agreed to in writing by PETERMANN-TECHNIK, any reproduction, modification, translation, compilation, or representation of this material shall be strictly prohibited. CRYSTALS ∙ OSCILLATORS ∙ CERAMIC RESONATORS ∙ CERAMIC FILTERS ∙ SAW COMPONENTS PAGE 7 OF 7 I SPEC 01 I REV.00 I NOVEMBER 2014