MICROCIRCUIT DATA SHEET Original Creation Date: 12/19/94 Last Update Date: 08/24/98 Last Major Revision Date: 12/19/94 MNLM6118-X REV 0C1 FAST SETTING DUAL OPERATIONAL AMPLIFIER General Description The LM6118 series are monolithic fast-setting unity-gain-compensated dual operational amplifiers with +20mA output drive capability. The PNP input stage has a typical bias current of 200nA, and the operating supply voltage is +5V to +20V. These dual op amps use slew enhancement with special mirror circuitry to achieve fast response and high gain with low total supply current. The amplifiers are built on a junction-isolated VIP(TM) (Vertically Integrated PNP) process which produces fast PNP's that complement the standard NPN's. Industry Part Number NS Part Numbers LM6118 LM6118E/883 * LM6118J/883 ** Prime Die LM6118 Controlling Document 5962-9156501M2A*, MPA** Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 12 13 14 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Settling time at Settling time at Settling time at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 Features - Low offset voltage 0.2mV 0.01% setting time 400nS Slew rate Av = -1 140V/uS Slew rate Av = +1 75V/uS Gain bandwidth 17MHz Total supply current 5.5mA Output drives 50 Ohm load (+1V) Applications - D/A converters - Fast integrators - Active filters 2 MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 (Absolute Maximum Ratings) (Note 1) Total Supply Voltage 42V Input Voltage (V+ - 1V) to (V-) Differential Input Current (Note 2) +10mA Output Current (Note 3) Internally Limited Power Dissipation (Note 4) 500mW ESD Tolerance (C = 100pF, R = 1.5k Ohm) Junction Temperature +4kV 150 C Storage Temperature Range -65 C to +150 C Lead Temperature (Soldering, 10 seconds) Note 1: Note 2: Note 3: Note 4: 300 C Absolute Maximum Ratings indicate limits beyond which damage to the device DC and AC electrical specifications do not apply when operating the device rated operating conditions. The inputs are shunted with three series-connected diodes back-to-back for differential clamping. Therefore differential input voltages greater than will cause excessive current to flow unless limited to less than 10mA. Current limiting protects the output from a short to ground or any voltage the supplies. With a continuous overload, the package dissipation must be account and heat sinking provided when necessary. Devices must be derated using a thermal resistance (Tja) of 90 C/W for the C/W for the E package, and Tjc of 12 C/W for both packages. Recommended Operating Conditions Operating Temperature Range LM6118 -55 C to +125 C 3 may occur. beyond its input about 1.8V less than taken into J and 80 MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +5V < Vs < +20V, Vcm = 0V, Vout = 0V, Iout = 0A, RS = 10K SYMBOL Vio Iio Iib CMRR PSRR+ PSRR- PSI Ios AV PARAMETER Input Offset Voltage CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vs = +15V -1.0 1.0 mV 1 Vs = +15V -2.0 2.0 mV 2, 3 V- + 3V < Vcm < V+ - 3.5V -1.5 1.5 mV 1 V- + 3V < Vcm < V+ - 3.5V -2.5 2.5 mV 2, 3 V- + 3V < Vcm < V+ - 3.5V -50 50 nA 1 V- + 3V < Vcm < V+ - 3.5V -250 250 nA 2, 3 V- + 3V < Vcm < V+ - 3.5V (Positive) -10 350 nA 1 V- + 3V < Vcm < V+ - 3.5V (Positive) -10 950 nA 2, 3 V- + 3V < Vcm < V+ - 3.5V (Negative) -350 10 nA 1 V- + 3V < Vcm < V+ - 3.5V (Negative) -950 10 nA 2, 3 V- + 3V < Vcm < V+ - 3.5V, Vs = +20V 90 dB 1 V- + 3V < Vcm < V+ - 3.5V, Vs = +20V 85 dB 2, 3 Positive Power Supply Rejection Ratio V- = 15V, 5V < V+ < 20V 90 dB 1 V- = 15V, 5V < V+ < 20V 85 dB 2, 3 Negative Power Supply Rejection Ratio V+ = 15V, -20V < V- < -5V 90 dB 1 V+ = 15V, -20V < V- < -5V 85 dB 2, 3 Total Supply Current Vs = +15V 0.6 7 mA 1 Vs = +15V 0.6 7.5 mA 2, 3 Vs = +15V, Pulsed (Sink) 10 100 mA 1 Vs = +15V, Pulsed (Source) -100 -10 mA 1 Vout = +16V, RL = 10K, Vs = +20V 150 V/mV 4 Vout = +16V, RL = 10K, Vs = +20V 100 V/mV 5, 6 Vout = +10V, RL = 500, Vs = +15V, (+20mA) 50 V/mV 4 Vout = +10V, RL = 500, Vs = +15V, (+20mA) 30 V/mV 5, 6 Input Offset Current Input Bias Current Input Common Mode Rejection Ratio Output Current Limit Large Signal Voltage Gain 4 MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 Electrical Characteristics AC PARAMETERS SYMBOL SR+ SR- GBW PARAMETER Slew Rate, Positive Slew Rate, Negative Gain-Bandwidth Product 0.01% Setting Time AV = -1 Note 1: CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = +1 50 V/uS 4 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = +1 30 V/uS 5, 6 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = -1 100 V/uS 4 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = -1 50 V/uS 5, 6 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = +1 50 V/uS 4 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = +1 30 V/uS 5, 6 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = -1 100 V/uS 4 Vs = +15V, Vout = +10V, RS = RF = 2K, CF = 10pF, AV = -1 50 V/uS 5, 6 Vs = +15V, fo = 200KHz 14 MHz 4 Vs = +15V, fo = 200KHz 10 MHz 5, 6 Delta Vout = 10V, Vs = +15V, RS=RF=2K, CF = 10pF 1 600 nS 4 Delta Vout = 10V, Vs = +15V, RS=RF=2K, CF = 10pF 1 750 nS 5, 6 Setting time separate insertion separate program. 5 MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 Graphics and Diagrams GRAPHICS# DESCRIPTION 06086HRC4 CERDIP (J), 8 LEAD (B/I CKT) 06192HRA4 LCC (E), TYPE C, 20 TERMINAL (B/I CKT) E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000016A CERDIP (J), 8 LEAD (PIN OUT) P000017A LCC (E), TYPE C, 20 TERMIAL (PIN OUT) See attached graphics following this page. 6 GENERAL NOTES: 1. GENERIC - INDUSTRY TYPE DEVICES THAT MAY BE USED WITH THIS CIRCUIT SHALL BE AS SPECIFIED IN NSC BURN-IN CIRCUIT LIST R512B-04. 2. ALL 1/4 AND 1/2 WATT RESISTORS SHALL BE METAL FILM. ALL 1, 2, AND 3 WATT RESISTORS SHALL BE WIRE WOUND. TOLERANCE SHALL BE +/-5% UNLESS OTHERWISE SPECIFIED. 3. ALL VOLTAGES SPECIFIED SHALL BE MEASURED AT THE “DEVICE UNDER TEST” PIN AND SHALL BE MINIMUM VALUES UNLESS OTHERWISE SPECIFIED. 4. WHEN APPLICABLE, CLOCK PULSES SPECIFIED SHALL HAVE 50% DUTY CYCLE. 5. THIS DRAWING COMPLIES WITH MIL-PRF-38535, WHEN APPLICABLE. ECN REV APPROVALS 05907 06590 07469 A1 B1 C1 C2 C3 C4 R Wallace P. Reid G. Wardwell G. Wardwell G. Wardwell T Trinh DATE 5/4/82 7/22/92 7/26/93 7/1/94 2/27/96 2/3/98 V+ 1 8 2 7 3 6 4 5 Note 7 vNote 7 C1 C1 Note 7 V+ = +15V, V- = -15V V+ = 7.5V, V- = -7.5V LMC6062, LMC6462 LMC6482, LM6142 LMC662, LPC662 LM6118, LM6172 DUT CONDITIONS SYMBOL V+ V- LIMITS MIN. MAX. +/+/- 0.5V 0.5V UNITS SYMBOL LIMITS MIN. MAX. UNITS COMPONENT REQUIREMENTS PER POSITION REF QTY DESCRIPTION DESIG. C1 (See Note 7) (See Note 7) 2 0.1 uF X7R +/- 20% NOTES: 6. LM6118, LMC662, LPC662, LMC6482 LMC6062, LMC6462, LM6142, LM6172 N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 CUSTOMER ORIGINATOR TXT DATE 2/3/98 OF SH BURN-IN CIRCUIT 1 PACKAGE TYPE CHECKED BY J8 MIL DATE NSC Note 6 TEST CONDITION DRAWING NUMBER 06086HR 1 A REV C4 GENERAL NOTES: 1. GENERIC - INDUSTRY TYPE DEVICES THAT MAY BE USED WITH THIS CIRCUIT SHALL BE AS SPECIFIED IN NSC BURN-IN CIRCUIT LIST R512B-04. 2. ALL 1/4 AND 1/2 WATT RESISTORS SHALL BE METAL FILM. ALL 1, 2, AND 3 WATT RESISTORS SHALL BE WIRE WOUND. TOLERANCE SHALL BE +/-5% UNLESS OTHERWISE SPECIFIED. 3. ALL VOLTAGES SPECIFIED SHALL BE MEASURED AT THE “DEVICE UNDER TEST” PIN AND SHALL BE MINIMUM VALUES UNLESS OTHERWISE SPECIFIED. 4. WHEN APPLICABLE, CLOCK PULSES SPECIFIED SHALL HAVE 50% DUTY CYCLE. 5. THIS DRAWING COMPLIES WITH MIL-PRF-38535, WHEN APPLICABLE. ECN REV APPROVALS DATE 06202 07573 07618 A1 A2 A3 A4 R Wallace G Wardwell J. GOMEZ J. GOMEZ 11/20/90 12/7/94 4/28/98 7/16/98 V+ 4 3 2 1 20 19 18 5 17 TOP VIEW 6 16 7 C1 15 8 9 10 11 +15V 12 14 13 V-15V C1 DUT CONDITIONS SYMBOL V+ V- LIMITS MIN. MAX. 14.5 15.5 -15.5 -14.5 UNITS SYMBOL LIMITS MIN. MAX. UNITS COMPONENT REQUIREMENTS PER POSITION REF QTY DESCRIPTION DESIG. C1 VOLTS VOLTS 2 0.1 uF X7R 20% NOTES: N MIL/AEROSPACE OPERATIONS CUSTOMER 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 ORIGINATOR J. GOMEZ DATE 7/16/98 OF SH BURN-IN CIRCUIT 1 PACKAGE TYPE CHECKED BY MIL E20 DATE NSC TEST CONDITION LM6118 DRAWING NUMBER 06192HR 1 A REV A4 OUT A -IN A +IN A V- 1 2 3 4 8 7 6 5 V+ OUT B -IN B +IN B LM6118J/883 CONNECTION DIAGRAM 8 LEAD DIP (TOP VIEW) P000016A V+ OUT A -IN A +IN A V- 4 5 6 7 8 3 2 1 20 19 18 TOP 17 16 VIEW 15 14 9 10 11 1213 OUT B -IN B +IN B LM6118E/883 CONNECTION DIAGRAM 20 LEAD LCC (TOP VIEW) P000017A MICROCIRCUIT DATA SHEET MNLM6118-X REV 0C1 Revision History Rev ECN # Originator Changes 0B0 M0001718 08/24/98 Rel Date Barbara Lopez Changed: MNLM6118-X Rev. 0A0 to MNLM6118-X Rev. 0B0. 0C1 M0002760 08/24/98 Rose Malone Update MDS: MNLM6118-X Rev. 0B0 to MNLM6118-X Rev. 0C1. Updated Burn-In graphics. Updated Subgroups to match SMD. 7