LTC3896 150V Low IQ, Synchronous Inverting DC/DC Controller Features Description Wide VIN + |VOUT– | Range: 4V to 140V (150V Abs Max) nn Wide Output Voltage Range: –60V to –0.8V nn Ground-Referenced Control / Interface Pins nn Adjustable Gate Drive Level 5V to 10V (OPTI-DRIVE) nn Integrated Bootstrap Diode nn Low Operating I : 40μA (Shutdown = 10μA) Q nn Selectable Gate Drive UVLO Thresholds nn Onboard LDO or External NMOS LDO for DRV CC nn EXTV LDO Powers Drivers from Output CC nn Phase-Lockable Frequency (75kHz to 850kHz) nn Programmable Fixed Frequency (50kHz to 900kHz) nn Selectable Continuous, Pulse-Skipping or Low Ripple Burst Mode® Operation at Light Loads nn Adjustable Burst Clamp and Current Limit nn Power Good Output Voltage Monitor nn Programmable Input Overvoltage Lockout nn 38-Lead TSSOP High Voltage Package The LTC®3896 is a high performance inverting DC/DC switching regulator controller that drives an all N-channel synchronous power MOSFET stage. It converts a wideranging positive input voltage source to a regulated negative output that can be as much as 60V below ground. The input can operate from a voltage as low as 4V and as high as 140V – |VOUT–|. nn Applications Automotive and Industrial Power Systems nn Telecommunications Power Supplies nn Distributed Power Systems The LTC3896 contains true ground-referenced RUN, PLLIN and PGOOD pins, eliminating the need for external discrete level-shifting components to interface with the LTC3896. A constant frequency current mode architecture allows a phase-lockable frequency of up to 850kHz. The low 40μA no-load quiescent current extends operating run time in battery-powered systems. OPTI-LOOP® compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3896 features a precision 0.8V reference and power good output indicator. The soft-start (SS) pin ramps the output voltage during start-up. L, LT, LTC, LTM, Linear Technology, the Linear logo, Burst Mode and OPTI-LOOP are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5481178, 5705919, 5929620, 6144194, 6177787, 6580258. nn Typical Application High Efficiency 36V–72V to –48V/2A Inverting Regulator Efficiency and Power Loss vs Load Current VIN 36V to 72V 100k 100 0V 0.1µF ×3 BOOST PGOOD NDRV 80 0.1µF GND VOUT– –48V 2A SW LTC3896 47µH DRVCC 4.7µF INTVCC 0.1µF SENSE+ DRVSET 301k 10mΩ DRVUV SENSE– SS 100pF 4.99k 15nF FREQ VOUT– VFB 10k 70 60 50 30 20 0 0.0001 590k 1k POWER LOSS 40 VIN = +48V VOUT– = –48V 10 BG ITH 0.1µF 4.7µF 100V 2220 ×4 EFFICIENCY FIGURE 16 CIRCUIT 0.001 0.01 0.1 LOAD CURRENT (A) 1 10 POWER LOSS (mW) 100k 90 TG PLLIN 0V 5V VIN RUN EFFICIENCY (%) 47µF 100 10 3896 TA01b 10k 3896 TA01a 3896f For more information www.linear.com/LTC3896 1 LTC3896 Absolute Maximum Ratings All pins with respect to VOUT– unless otherwise noted (Note 1). Input Supply Voltage (VIN)........................ –0.3V to 150V Top Side Driver Voltage BOOST............... –0.3V to 150V Switch Voltage (SW) .................................. –5V to 150V DRVCC, (BOOST – SW) Voltages................. –0.3V to 11V BG, TG................................................................ (Note 8) GND Voltage............................................... –0.3V to 65V RUN Voltage................................... (GND–0.3V) to 150V (PLLIN – GND) Voltage................................. –0.3V to 6V (PGOOD – GND) Voltage............................... –0.3V to 6V SENSE+, SENSE– Voltages.......................... –0.3V to 65V MODE, DRVUV Voltages............................... –0.3V to 6V ILIM, VPRG, FREQ, PHASMD Voltages......... –0.3V to 6V DRVSET Voltage........................................... –0.3V to 6V NDRV.................................................................. (Note 9) EXTVCC Voltage.......................................... –0.3V to 14V ITH, VFB Voltages......................................... –0.3V to 6V SS, OVLO Voltages...................................... –0.3V to 6V Operating Junction Temperature Range (Notes 2, 3) LTC3896E, LTC3896I......................... –40°C to 125°C LTC3896H.......................................... –40°C to 150°C Storage Temperature Range.................. –65°C to 150°C Pin Configuration TOP VIEW OVLO 1 38 INTVCC VPRG 2 37 ILIM SENSE+ 3 36 PHASMD SENSE– 4 SS 5 VFB 6 ITH 7 MODE 8 VOUT– 9 – VOUT 10 CLKOUT 11 34 RUN 32 EXTVCC 39 30 VIN – VOUT 28 NDRV GND 12 PLLIN 13 26 DRVCC PGOOD 14 VOUT– 15 24 BG NC 16 FREQ 17 22 BOOST DRVSET 18 21 SW DRVUV 19 20 TG FE PACKAGE 38-LEAD PLASTIC TSSOP TJMAX = 150°C, θJA = 28°C/W EXPOSED PAD (PIN 39) IS VOUT–, MUST BE SOLDERED TO PCB FOR RATED ELECTRICAL AND THERMAL CHARACTERISTICS Order Information http://www.linear.com/product/LTC3896#orderinfo LEAD FREE FINISH TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3896EFE#PBF LTC3896EFE#TRPBF LTC3896FE 38-Lead Plastic TSSOP –40°C to 125°C LTC3896IFE#PBF LTC3896IFE#TRPBF LTC3896FE 38-Lead Plastic TSSOP –40°C to 125°C LTC3896HFE#PBF LTC3896HFE#TRPBF LTC3896FE 38-Lead Plastic TSSOP –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on nonstandard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2 3896f For more information www.linear.com/LTC3896 LTC3896 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, VRUN = 5V with respect to GND, EXTVCC = 0V, VDRVSET = 0V, VPRG = FLOAT unless otherwise noted. All pin voltages with respect to VOUT–, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN – VIN Input Supply Operating Voltage Range (VIN + |VOUT–|) (Note 10) DRVUV = VOUT VOUT– Regulated Output Voltage Set Point VIN + |VOUT–| ≤ 140V VFB Regulated Feedback Voltage (Note 4); ITH Voltage = 1.2V 0°C to 85°C, VPRG = FLOAT VPRG = FLOAT VPRG = VOUT– VPRG = INTVCC IFB Feedback Current 4 140 V –60 –0.8 V 0.800 0.800 3.300 5.000 0.808 0.812 3.380 5.125 V V V V –0.006 4 ±0.050 6 µA µA 0.792 0.788 3.220 4.875 Reference Voltage Line Regulation (Note 4) VIN = 4.5V to 150V 0.002 0.02 %/V (Note 4) Measured in Servo Loop, ∆ITH Voltage = 1.2V to 0.7V l 0.01 0.1 % (Note 4) Measured in Servo Loop, ∆ITH Voltage = 1.2V to 1.6V l –0.01 –0.1 % Transconductance Amplifier gm (Note 4) ITH = 1.2V, Sink/Source 5µA Input DC Supply Current (Note 5) VDRVSET = VOUT– 2.2 Pulse-Skipping or Forced Continuous Mode VFB = 0.83V (No Load) 2.5 VFB = 0.83V (No Load) 40 55 µA Shutdown RUN = 0V with Respect to GND 10 20 µA Undervoltage Lockout DRVCC Ramping Up DRVUV = VOUT– DRVUV = INTVCC, DRVSET = INTVCC l l 4.0 7.5 4.2 7.8 V V DRVCC Ramping Down DRVUV = VOUT– DRVUV = INTVCC, DRVSET = INTVCC l l 3.6 6.4 3.8 6.7 4.0 7.0 V V VRUN Rising with Respect to GND l 1.1 1.2 1.3 V VOVLO Rising with Respect to VOUT– l 1.1 1.2 RUN Pin ON Threshold RUN Pin Hysteresis OVLO Overvoltage Lockout Threshold OVLO Hysteresis Feedback Overvoltage Protection ISS mA 80 OVLO Delay ISENSE+ ISENSE– mmho Sleep Mode VRUN Hyst OVLO Hyst UNITS Output Voltage Load Regulation gm VRUN ON MAX (Note 4) VPRG = FLOAT VPRG = VOUT– or INTVCC IQ UVLO l l l TYP Measured at VFB, Relative to Regulated VFB 7 mV 1.3 V 100 mV 1 µs 10 SENSE+ Pin Current 13 % ±1 µA ±1 µA µA SENSE– Pin Current SENSE– < VINTVCC – 0.5V SENSE– > VINTVCC + 0.5V Maximum Duty Factor FREQ = VOUT– 98 99 Soft-Start Charge Current VSS = 0V 8 10 12 µA 66 43 90 75 50 100 84 57 109 mV mV mV VSENSE(MAX) Maximum Current Sense Threshold 850 VFB = 0.7V, VSENSE– = 3.3V ILIM = FLOAT ILIM = VOUT– ILIM = INTVCC l l l % Gate Driver TG Pull-Up On-Resistance TG Pull-Down On-Resistance VDRVSET = INTVCC 2.2 1.0 Ω Ω 3896f For more information www.linear.com/LTC3896 3 LTC3896 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, VRUN = 5V with respect to GND, EXTVCC = 0V, VDRVSET = 0V, VPRG = FLOAT unless otherwise noted. All pin voltages with respect to VOUT–, unless otherwise noted. SYMBOL tON(MIN) PARAMETER CONDITIONS MIN TYP MAX UNITS BG Pull-Up On-Resistance BG Pull-Down On-Resistance VDRVSET = INTVCC 2.0 1.0 Ω Ω BOOST to DRVCC Switch On-Resistance VSW = 0V, VDRVSET = INTVCC 11 Ω TG Transition Time: Rise Time Fall Time (Note 6) VDRVSET = INTVCC CLOAD = 3300pF CLOAD = 3300pF 25 15 ns ns BG Transition Time: Rise Time Fall Time (Note 6) VDRVSET = INTVCC CLOAD = 3300pF CLOAD = 3300pF 25 15 ns ns Top Gate Off to Bottom Gate On Delay Synchronous Switch-On Delay Time CLOAD = 3300pF each driver, VDRVSET = INTVCC 55 ns Bottom Gate Off to Top Gate On Delay Top Switch-On Delay Time CLOAD = 3300pF each driver, VDRVSET = INTVCC 50 ns TG Minimum On-Time (Note 7) VDRVSET = INTVCC 80 ns DRVCC LDO Regulator DRVCC Voltage from NDRV LDO Regulator NDRV Driving External NFET, VEXTVCC = 0V 7V < VIN < 150V, DRVSET = VOUT– 11V < VIN < 150V, DRVSET = INTVCC DRVCC Load Regulation from NDRV LDO Regulator NDRV Driving External NFET ICC = 0mA to 50mA, VEXTVCC = 0V DRVCC Voltage from Internal VIN LDO NDRV = DRVCC (NDRV LDO Off), VEXTVCC = 0V 7V < VIN < 150V, DRVSET = VOUT– 11V < VIN < 150V, DRVSET = INTVCC DRVCC Load Regulation from VIN LDO ICC = 0mA to 50mA, VEXTVCC = 0V DRVSET = VOUT DRVSET = INTVCC DRVCC Voltage from Internal EXTVCC LDO 7V < VEXTVCC < 13V, DRVSET = VOUT– 11V < VEXTVCC < 13V, DRVSET = INTVCC DRVCC Load Regulation from Internal EXTVCC LDO ICC = 0mA to 50mA DRVSET = VOUT–, VEXTVCC = 8.5V DRVSET = INTVCC, VEXTVCC = 13V EXTVCC LDO Switchover Voltage EXTVCC Ramping Positive DRVUV = VOUT– DRVUV = INTVCC, DRVSET = INTVCC 5.8 9.6 5.6 9.5 5.8 9.6 4.5 7.4 EXTVCC Hysteresis Programmable DRVCC RDRVSET = 50kΩ, NDRV Driving External NFET, VEXTVCC = 0V Programmable DRVCC RDRVSET = 70kΩ, NDRV Driving External NFET, VEXTVCC = 0V Programmable DRVCC RDRVSET = 90kΩ, NDRV Driving External NFET, VEXTVCC = 0V 6.4 6.0 10.0 6.2 10.4 V V 0 1.0 % 5.85 9.85 6.1 10.3 V V 1.4 0.9 2.5 2.0 % % 6.0 10.0 6.2 10.4 V V 0.7 0.5 2.0 2.0 % % 4.7 7.7 4.9 8.0 V V 250 mV 5.0 V 7.0 7.6 9.0 V V INTVCC LDO Regulator VINTVCC INTVCC Voltage ICC = 0mA to 2mA 4.7 5.0 375 440 5.2 V 505 kHz Oscillator and Phase-Locked Loop 4 Programmable Frequency RFREQ = 25kΩ, PLLIN = DC Voltage Programmable Frequency RFREQ = 65kΩ, PLLIN = DC Voltage Programmable Frequency RFREQ = 105kΩ, PLLIN = DC Voltage 105 835 kHz kHz 3896f For more information www.linear.com/LTC3896 LTC3896 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, VRUN = 5V with respect to VOUT–, EXTVCC = 0V, VDRVSET = 0V, VPRG = FLOAT unless otherwise noted. All pin voltages with respect to VOUT–, unless otherwise noted. SYMBOL fSYNC PARAMETER CONDITIONS –, PLLIN = DC Voltage MIN TYP MAX UNITS 320 350 380 kHz 485 535 Low Fixed Frequency VFREQ = VOUT High Fixed Frequency VFREQ = INTVCC, PLLIN = DC Voltage Synchronizable Frequency PLLIN = External Clock l 75 PLLIN Input High Level PLLIN Input Low Level PLLIN = External Clock with Respect to GND PLLIN = External Clock with Respect to GND l l 2.8 585 kHz 850 kHz 0.5 V V PGOOD Output VPGL PGOOD Voltage Low IPGOOD = 2mA, VPGL with Respect to GND IPGOOD PGOOD Leakage Current VPGOOD = 3.3V PGOOD Trip Level VFB with Respect to Set Regulated Voltage VFB Ramping Negative Hysteresis –13 VFB with Respect to Set Regulated Voltage VFB Ramping Positive Hysteresis 7 Delay for Reporting a Fault 0.02 0.04 V 10 µA –10 2.5 –7 % % 10 2.5 13 % % 40 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3896 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3896E is guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3896I is guaranteed over the –40°C to 125°C operating junction temperature range and the LTC3896H is guaranteed over the –40°C to 150°C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. High temperatures degrade operating lifetimes; operating lifetime is derated for junction temperatures greater than 125°C. The junction temperature (TJ, in °C) is calculated from the ambient temperature (TA, in °C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD • θJA) where θJA = 28°C/W for the TSSOP package. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. µs Note 4: The LTC3896 is tested in a feedback loop that servos VITH to a specified voltage and measures the resultant VFB. The specification at 85°C is not tested in production and is assured by design, characterization and correlation to production testing at other temperatures (125°C for the LTC3896E and LTC3896I, 150°C for the LTC3896H). For the LTC3896I and LTC3896H, the specification at 0°C is note tested in production and is assured by design, characterization and correlation to production testing at –40°C. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. See the Applications Information section. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: The minimum on-time condition is specified for an inductor peak-to-peak ripple current >40% of IMAX (see Minimum On-Time Considerations in the Applications Information section). Note 8: Do not apply a voltage or current source to these pins. They must be connected to capacitive loads only, otherwise permanent damage may occur. Note 9: Do not apply a voltage or current source to the NDRV pin, other than tying NDRV to DRVCC when not used. If used it must be connected to capacitive loads only (see DRVCC Regulators (OPTI-DRIVE) in the Applications Information section), otherwise permanent damage may occur. Note 10: The minimum input supply (VIN + |VOUT–|) operating range is dependent on the DRVCC UVLO thresholds as determined by the DRVUV pin setting. 3896f For more information www.linear.com/LTC3896 5 LTC3896 Typical Performance Characteristics VIN and VOUT– with respect to GND. All other voltages with respect to VOUT–, unless otherwise noted. Efficiency and Power Loss vs Load Current BURST EFFICIENCY PS EFFICIENCY 60 FCM LOSS 50 PS LOSS 40 30 100 90 98 80 96 70 94 10k 70 POWER LOSS (mW) EFFICIENCY (%) 80 FCM EFFICIENCY BURST LOSS 20 0 0.0001 100 FIGURE 16 CIRCUIT VIN = +48V VOUT– = –48V 10 0.001 0.01 0.1 LOAD CURRENT (A) 1 1k 10 60 50 40 30 20 FIGURE 16 CIRCUIT 10 VOUT– = –48V 0 0.0001 0.001 0.01 0.1 LOAD CURRENT (A) 10 Efficiency vs Input Voltage 100 EFFICIENCY (%) 90 Efficiency vs Load Current 100k EFFICIENCY (%) 100 3896 G01 90 88 86 84 VIN = 36V VIN = 48V VIN = 72V 1 92 FIGURE 16 CIRCUIT VOUT– = –48V ILOAD = 1.5A 82 80 10 35 Load Step Burst Mode Operation 45 50 55 60 65 INPUT VOLTAGE (V) VOUT– 100mV/DIV AC-COUPLED VOUT– 100mV/DIV AC-COUPLED IL 1A/DIV IL 1A/DIV IL 1A/DIV 3896 G05 200µs/DIV VOUT– = –48V LOAD STEP = 0A to 1A FIGURE 16 CIRCUIT Inductor Current at Light Load 75 Load Step Forced Continuous Mode Load Step Pulse-Skipping Mode 3896 G04 70 3896 G03 VOUT– 100mV/DIV AC-COUPLED 200µs/DIV VOUT– = –48V LOAD STEP = 0A to 1A FIGURE 16 CIRCUIT 40 3896 G02 – = –48V 3896 G06 200µs/DIV VOUT LOAD STEP = 0A to 1A FIGURE 16 CIRCUIT Regulated Feedback Voltage vs Temperature Soft Start-Up FORCED CONTINUOUS MODE GND BURST MODE OPERATION 2A/DIV GND – PULSESKIPPING MODE VOUT 20V/DIV 10µs/DIV VOUT– = –48V ILOAD = 1mA FIGURE 16 CIRCUIT 3896 G07 1ms/DIV VOUT– = –48V FIGURE 16 CIRCUIT 3896 G08 REGULATED FEEDBACK VOLTAGE (V) 808 RUN 2V/DIV 806 804 802 800 798 796 794 792 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G09 6 3896f For more information www.linear.com/LTC3896 LTC3896 Typical Performance Characteristics VIN and VOUT– with respect to GND. All other voltages with respect to VOUT–, unless otherwise noted. 6.5 5.5 VIN LDO (No NDRV FET), EXTVCC = 0V EXTVCC = 8.5V 5.0 20 5.0 EXTVCC RISING 9.5 9.0 8.5 8.0 40 60 80 LOAD CURRENT (mA) 4.0 –75 –50 –25 100 3896 G11 SENSE– Pins Input Current vs VSENSE Voltage Undervoltage Lockout Threshold vs Temperature 8.0 900 900 7.5 800 800 SENSE– CURRENT (µA) 1000 500 400 300 600 500 400 300 200 200 100 100 0 100 90 60 50 40 30 ILIM = FLOAT ILIM = GND ILIM = INTVCC 0 0 100 200 300 400 500 600 700 800 FEEDBACK VOLTAGE (mV) 3896 G16 CURRENT SENSE VOLTAGE (mV) MAXIMUM CURRENT SENSE VOLTAGE (mV) 100 10 5.5 5.0 4.5 RISING 0 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G15 RUN Threshold vs Temperature 5% DUTY CYCLE 80 PULSE–SKIPPING 60 Burst Mode OPERATION 40 20 ILIM = GND 0 ILIM = FLOAT –20 –40 FORCED CONTINUOUS 0 0.2 0.4 0.6 0.8 VITH (V) ILIM = INTVCC 1.0 DRVUV = 0V FALLING 3.0 –75 –50 –25 Maximum Current Sense Threshold vs ITH Voltage 70 FALLING 6.0 3896 G14 Foldback Current Limit 20 6.5 3.5 VOUT ≤ INTVCC – 0.5V 3896 G13 80 DRVUV = INTVCC 4.0 0 –75 –50 –25 0 5 10 15 20 25 30 35 40 45 50 55 60 65 VSENSE COMMON MODE VOLTAGE (V) RISING 7.0 DRVCC VOLTAGE (V) 600 VOUT ≥ INTVCC + 0.5V 1.2 1.4 3896 G17 RUN PIN VOLTAGE REFERENCED TO GND (V) SENSE– CURRENT (µA) 1000 700 EXTVCC FALLING 3896 G12 SENSE– Pin Input Bias Current vs Temperature 700 EXTVCC RISING DRVUV = DRVSET = INTVCC 7.0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G10 NDRV LDO (NDRV NFET) EXTVCC = 0V VIN LDO (No NDRV NFET) EXTVCC = 0V 7.5 EXTVCC FALLING DRVUV = DRVSET = 0V DRVUV = DRVSET = 0V 0 NDRV LDO (NDRV FET) EXTVCC = 0V VIN LDO (No NDRV FET) EXTVCC = 0V 5.5 4.5 EXTVCC = 5V 4.5 EXTVCC = 8.5V 10.0 6.0 DRVCC VOLTAGE (V) DRVCC VOLTAGE (V) 10.5 EXTVCC = 8.5V NDRV LDO (NDRV FET), EXTVCC = 0V 6.0 4.0 EXTVCC Switchover and DRVCC Voltages vs Temperature DRVCC VOLTAGE (V) 6.5 EXTVCC Switchover and DRVCC Voltages vs Temperature DRVCC vs Load Current 1.40 1.35 1.30 1.25 1.20 RUN RISING 1.15 1.10 RUN FALLING 1.05 1.00 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G18 3896f For more information www.linear.com/LTC3896 7 LTC3896 Typical Performance Characteristics VIN and VOUT– with respect to GND. All other voltages with respect to VOUT–, unless otherwise noted. 18 DRVSET = INTVCC 10 DRVCC VOLTAGE (V) 20 9 NDRV FET 8 No NDRV FET 7 DRVSET = 0V 6 30 VIN = 12V 25 16 SHUTDOWN CURRENT (µA) EXTVCC = 0V 14 12 10 8 6 4 0 15 30 45 60 75 90 105 120 135 150 INPUT VOLTAGE (V) 0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G19 VIN = 6.3V 0 0 15 30 45 60 75 90 105 120 135 150 INPUT VOLTAGE (V) 3896 G21 600 VIN – VOUT– = 12V 90 Burst Mode OPERATION 550 80 FREQ = INTVCC DRVSET = 70kΩ FREQUENCY (kHz) QUIESCENT CURRENT (µA) 10 Oscillator Frequency vs Temperature 100 60 15 3896 G20 Quiescent Current vs Temperature 70 20 5 2 5 Shutdown Current vs Input Voltage Shutdown Current vs Temperature SHUTDOWN CURRENT (µA) 11 DRVCC Line Regulation DRVSET = INTVCC 50 40 DRVSET = 0V 30 20 500 450 400 350 FREQ = 0V 10 0 –75 –50 –25 300 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G22 3896 G23 SS Pull-Up Current vs Temperature OVLO Threshold vs Temperature OVLO PIN VOLTAGE REFERENCED TO VOUT- (V) 12.0 11.5 SS CURRENT (µA) 11.0 10.5 10.0 9.5 9.0 8.5 8.0 –75 –50 –25 0 25 50 75 100 125 150 TEMPERATURE (°C) 1.40 1.35 1.30 1.25 1.20 1.15 1.10 1.05 1.00 –75 –50 –25 3896 G24 8 OVLO RISING OVLO FALLING 0 25 50 75 100 125 150 TEMPERATURE (°C) 3896 G25 3896f For more information www.linear.com/LTC3896 LTC3896 Pin Functions OVLO (Pin 1): Overvoltage Lockout Input. A voltage on this pin above 1.2V with respect to VOUT– disables switching of the controller. The DRVCC and INTVCC supplies maintain regulation during an OVLO event. Exceeding the OVLO threshold triggers a soft-start reset. If the OVLO function is not used, connect this pin to VOUT–. VPRG (Pin 2): Output Voltage Control Pin. This pin sets the regulator in adjustable output mode using external feedback resistors or fixed –5V/–3.3V output mode. Floating this pin allows the output to be programmed from –0.8V to –60V with an external resistor divider on the VFB pin, regulating VFB to 0.8V with respect to VOUT–. Tying this pin to INTVCC or VOUT– programs the output to –5V or –3.3V, respectively, through an internal resistor divider on VFB. In fixed –5V/–3.3V output mode, VFB should connect to GND, which is the positive terminal of the output. SENSE+ (Pin 3): The (+) Input to the Differential Current Comparator. The ITH pin voltage and controlled offsets between the SENSE– and SENSE+ pins in conjunction with RSENSE set the current trip threshold. SENSE– (Pin 4): The (–) Input to the Differential Current Comparator. When SENSE– is greater than INTVCC, the SENSE– pin supplies power to the current comparator. SS (Pin 5): Soft-Start Input. The LTC3896 regulates the VFB voltage with respect to VOUT– to the smaller of 0.8V or the voltage on the SS pin. An internal 10μA pull-up current source is connected to this pin. A capacitor to VOUT– at this pin sets the ramp time to final regulated output voltage. The SS pin is also used for the Regulator Shutdown (REGSD) feature. A 5μA/1μA pull-down current can be connected on SS depending on the state of the EXTVCC LDO and the voltage on SS. See Regulator Shutdown (REGSD) section in the Operation section for more information. To defeat the REGSD feature, place a 330kΩ or smaller resistor between INTVCC and SS. See Soft-Start Pin in the Applications Information section for more information on defeating REGSD. VFB (Pin 6): Feedback Input. If the VPRG pin is floating, the VFB pin receives the remotely sensed feedback voltage from an external resistor divider across the output. If VPRG is tied to VOUT– or INTVCC, the VFB pin should connect to the GND pin. ITH (Pin 7): Error Amplifier Output and Switching Regulator Compensation Point. The current comparator trip point increases with this control voltage. MODE (Pin 8): Mode Select and Burst Clamp Adjust Input. This input determines how the LTC3896 operates at light loads. Pulling this pin to VOUT– selects Burst Mode operation with the burst clamp level defaulting to 25% of VSENSE(MAX). Tying this pin to a voltage between 0.5V and 1.0V with respect to VOUT– selects Burst Mode operation and adjusts the burst clamp between 10% and 60%. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.4V and less than INTVCC –1.3V (with respect to VOUT–) selects pulse-skipping operation. VOUT– (Pins 9, 15, Exposed Pin 39): Negative Terminal of Output Voltage. This serves as a virtual ground return for most of the LTC3896’s circuits. Most pins and components are referenced to VOUT–, which can operate at up to 60V (65V Abs Max) below the GND pin. The exposed pad must be soldered to the PCB for rated electrical and thermal performance. VOUT– (Pin 10): This pin must be externally tied to the other VOUT– pins (Pin 9, e.g.) but is not internally electrically connected to them. CLKOUT (Pin 11): Output Clock Signal. This signal is available to daisy-chain other controller ICs for additional MOSFET driver stages/phases. The output levels swing from INTVCC to VOUT–. GND (Pin 12): Ground. This pin should be externally tied to the true ground (e.g., ground terminal of the positive input supply connected to VIN). The RUN, PLLIN, and PGOOD pins are referenced to this GND pin. 3896f For more information www.linear.com/LTC3896 9 LTC3896 Pin Functions PLLIN (Pin 13): External Synchronization Input to Phase Detector. When an external clock is applied to this pin, the phase-locked loop will force the rising TG signal to be synchronized with the rising edge of the external clock. If the MODE pin is set to Forced Continuous Mode or Burst Mode operation, then the regulator operates in Forced Continuous Mode when synchronized. If the MODE pin is set to pulse-skipping mode, then the regulator operates in pulse-skipping mode when synchronized. The PLLIN pin is referenced to the GND pin, allowing the LTC3896 to be used with a true ground-referenced external clock source with no level shifters needed. PGOOD (Pin 14): Open-Drain Logic Output. PGOOD is pulled to GND when the voltage on the VFB pin is not within ±10% of its set point. PGOOD is referenced to GND to allow it to interface with external true ground-referenced components with no level shifters needed. NC (Pin 16): No connect. Float this pin or connect to GND or VOUT–. TG (Pin 20): High Current Gate Drives for Top N-Channel MOSFET. This is the output of floating high side driver with a voltage swing equal to DRVCC superimposed on the switch node voltage SW. SW (Pin 21): Switch Node Connection to Inductor. BOOST (Pin 22): Bootstrapped Supply to the Topside Floating Driver. A capacitor is connected between the BOOST and SW pins. Voltage swing at the BOOST pin is from approximately DRVCC to (VIN + DRVCC). BG (Pin 24): High Current Gate Drive for Bottom (Synchronous) N-Channel MOSFET. Voltage swing at this pin is from VOUT– to DRVCC. DRVCC (Pin 26): Output of the Internal or External Low Dropout Regulators. The gate drivers are powered from this voltage source. The DRVCC voltage is set by the DRVSET pin. Must be decoupled to VOUT– with a minimum of 4.7µF ceramic or other low ESR capacitor, as close as possible to the IC. Do not use the DRVCC pin for any other purpose. FREQ (Pin 17): Frequency Control Pin for the Internal VCO. Connecting the pin to VOUT– forces the VCO to a fixed low frequency of 350kHz. Connecting the pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. Other frequencies between 50kHz and 900kHz can be programmed by using a resistor between FREQ and VOUT–. An internal 20µA pull-up current develops the voltage to be used by the VCO to control the frequency. NDRV (Pin 28): Drive Output for External Pass Device of the NDRV LDO Linear Regulator for DRVCC. Connect this pin to the gate of an external NMOS pass device. To disable this external NDRV LDO, tie NDRV to DRVCC. DRVSET (Pin 18): DRVCC Regulation Program Pin. This pin sets the regulated output voltage of the DRVCC linear regulator. Tying this pin to VOUT– sets DRVCC to 6.0V. Tying this pin to INTVCC sets DRVCC to 10V. Other voltages between 5V and 10V can be programmed by placing a resistor (50k to 100k) between the DRVSET pin and VOUT–. An internal 20µA pull-up current develops the voltage to be used as the reference to the DRVCC LDO. EXTVCC (Pin 32): External Power Input to an Internal LDO linear regulator Connected to DRVCC. This LDO supplies DRVCC power from EXTVCC, bypassing the internal LDO powered from VIN or the external NDRV LDO whenever EXTVCC is higher than its switchover threshold (4.7V or 7.7V referenced to VOUT– depending on the DRVUV pin). See the EXTVCC Connection section in the Applications Information section. Do not exceed 14V with respect to VOUT– on this pin. Do not connect EXTVCC to a voltage greater than VIN. Connect to VOUT– if not used. DRVUV (Pin 19): DRVCC UVLO Program Pin. This pin determines the higher or lower DRVCC UVLO and EXTVCC switchover thresholds, as listed on the Electrical Characteristics table. Connecting DRVUV to VOUT– chooses the lower thresholds whereas tying DRVUV to INTVCC chooses the higher thresholds. Do not float this pin. 10 VIN (Pin 30): Main Supply Pin. A bypass capacitor should be tied between this pin and the GND pin. An additional bypass capacitor between the VIN and VOUT– pins is recommended. 3896f For more information www.linear.com/LTC3896 LTC3896 Pin Functions RUN (Pin 34): Run Control Input. Forcing this pin below 1.12V (with respect to GND) shuts down the controller. Forcing this pin below 0.7V shuts down the entire LTC3896, reducing quiescent current to approximately 10µA. The RUN pin is referenced to the GND pin, allowing the LTC3896 to be used with a true ground-referenced external signal or logic with no level shifters needed. This pin can be tied to VIN for always-on operation. Do not float this pin. PHASMD (Pin 36): Control Input to Phase Selector. This pin determines the CLKOUT phase relationships with respect to TG. Pulling this pin to VOUT– forces CLKOUT to be out of phase 90° with respect to TG. Connecting this pin to INTVCC forces CLKOUT to be out-of-phase 120° with respect to TG. Floating this pin forces CLKOUT to be out of phase 180° with respect to TG. ILIM (Pin 37): Current Comparator Sense Voltage Range Input. Tying this pin to VOUT– or INTVCC or floating it sets the maximum current sense threshold to one of three different levels (50mV, 100mV, and 75mV, respectively). INTVCC (Pin 38): Output of the Internal 5V (referenced to VOUT–) Low Dropout Regulator. CLKOUT and many of the low voltage analog and digital circuits are powered from this voltage source. A low ESR 0.1µF ceramic bypass capacitor should be connected between INTVCC and VOUT–, as close as possible to the IC. 3896f For more information www.linear.com/LTC3896 11 LTC3896 Block Diagram PGOOD 0.88V LVLSHFT DRVCC EA– GND VOUT– 0.72V OVLO RUN 15M GND + 1.2V S 3V PHASMD FREQ Q TG TOP DROPOUT DETECT R MODE CLKOUT VIN BOOST VOUT– + 1.2V CINA BOT INTVCC DRVCC BG BOT VOUT– VOUT– 0.425V CLK VCO 20µA VOUT– SLEEP IR ICMP L COUT PFD SENSE+ 2mV VOUT– PLLIN 100k VOUT ILIM DRVSET 1.8V BCLAMP EA 0.80V SS CURRENT LIMIT 20µA VFB R1 EA– SLOPE COMP – VOUT– VOUT– 0.88V 2.0V 1.2V VPRG DRVCC LDO/UVLO CONTROL CHARGE PUMP INTVCC VOUT– ∞ 200k 200k RC VOUT– 4.7V/ 7.7V VOUT– SS EXTVCC LDO CSS REGSD R R2 EN EN VIN LDO NDRV LDO DRVCC CC2 10µA SHDN EN R1 CC1 3.5V VIN VOUT– VPRG FLOAT ADJUSTABLE 0 VOUT– –3.3V FIXED 625k INTVCC –5V FIXED 1.05M ITH EXTVCC NDRV RB RA R2 DRVUV VIN RSENSE SENSE– SYNC DET LVLSHFT CINB SW SWITCH LOGIC TOP ON CB INTVCC LDO 4R VOUT– 5µA/1µA VOUT– VOUT– 3896 BD * ALL VOLTAGES WITH RESPECT TO VOUT– UNLESS OTHERWISE NOTED. 12 3896f For more information www.linear.com/LTC3896 LTC3896 Operation Main Control Loop The LTC3896 uses a constant frequency, current mode control architecture. During normal operation, the external top MOSFET is turned on when the clock sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier, EA. The error amplifier compares the output voltage feedback signal at the VFB pin (which is generated with an external resistor divider connected across ground (GND) to the negative output voltage, VOUT–) to the internal 0.800V reference voltage (referenced to VOUT–). When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. After the top MOSFET is turned off each cycle, the bottom MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. DRVCC/EXTVCC/INTVCC Power Power for the top and bottom MOSFET drivers is derived from the DRVCC pin. The DRVCC supply voltage can be programmed from 5V to 10V referenced to VOUT– by setting the DRVSET pin. Two separate LDOs (low dropout linear regulators) can provide power from VIN to DRVCC. The internal VIN LDO uses an internal P-channel pass device between the VIN and DRVCC pins. To prevent high on-chip power dissipation in high input voltage applications, the LTC3896 also includes an NDRV LDO that utilizes the NDRV pin to supply power to DRVCC by driving the gate of an external N-channel MOSFET acting as a linear regulator with its source connected to DRVCC and drain connected to VIN. The NDRV LDO includes an internal charge pump that allows NDRV to be driven above VIN for low dropout performance. When the EXTVCC pin is tied to a voltage below its switchover voltage (4.7V or 7.7V with respect to VOUT–, depending on the DRVUV pin), the VIN and NDRV LDOs are enabled and one of them supplies power from VIN to DRVCC. The VIN LDO has a slightly lower regulation point than the NDRV LDO. If the NDRV LDO is being used with an external N-channel MOSFET, the gate of the MOSFET tied to the NDRV pin is driven such that DRVCC regulates above the VIN LDO regulation point, causing all DRVCC current to flow through the external N-channel MOSFET, bypassing the internal VIN LDO pass device. If the NDRV LDO is not being used, all DRVCC current flows through the internal P-channel pass device between the VIN and DRVCC pins. If EXTVCC is taken above its switchover voltage, the VIN and NDRV LDOs are turned off and an EXTVCC LDO is turned on. Once enabled, the EXTVCC LDO supplies power from EXTVCC to DRVCC. Using the EXTVCC pin allows the DRVCC power to be derived from a high efficiency external source such as the LTC3896 switching regulator output. The top MOSFET driver is biased from the floating bootstrap capacitor, CB, which normally recharges during each cycle through an internal switch whenever SW goes low. The INTVCC supply powers most of the other internal circuits in the LTC3896. The INTVCC LDO regulates to a fixed value of 5V (with respect to VOUT–) and its power is derived from the DRVCC supply. Shutdown and Start-Up (RUN, SS Pins) The LTC3896 can be shut down using the RUN pin. Connecting the RUN pin below 1.12V (with respect to GND) shuts down the main control loop. Connecting the RUN pin below 0.7V disables the controller and most internal circuits, including the DRVCC and INTVCC LDOs. In this state, the LTC3896 draws only 10μA of quiescent current. The RUN pin has no internal pull-up current, so the pin must be externally pulled up or driven directly by logic. The RUN pin can tolerate up to 150V (with respect to VOUT–), so it can be conveniently tied to VIN in always-on applications where the controller is enabled continuously and never shut down. The start-up of the controller’s output voltage VOUT– is controlled by the voltage on the SS pin. When the voltage on the SS pin is less than the 0.8V internal reference (with respect to VOUT–), the LTC3896 regulates the VFB voltage to the SS pin voltage instead of the 0.8V reference. This allows the SS pin to be used to program a soft-start by connecting an external capacitor from the SS pin to VOUT–. 3896f For more information www.linear.com/LTC3896 13 LTC3896 Operation An internal 10μA pull-up current charges this capacitor creating a voltage ramp on the SS pin. As the SS voltage rises linearly from VOUT– to 0.8V above VOUT– (and beyond), the output voltage VOUT– descends smoothly from zero to its final negative value. Light Load Current Operation (Burst Mode Operation, Pulse-Skipping or Forced Continuous Mode) (MODE Pin) The LTC3896 can be enabled to enter high efficiency Burst Mode operation, constant frequency pulse-skipping mode, or forced continuous conduction mode at light load currents. To select Burst Mode operation, tie the MODE pin to VOUT– or a voltage between 0.5V and 1.0V (with respect to VOUT–). To select forced continuous operation, tie the MODE pin to INTVCC. To select pulse-skipping mode, tie the MODE pin to a DC voltage greater than 1.4V and less than INTVCC – 1.3V (with respect to VOUT–). This can be done with a simple resistor divider between INTVCC and VOUT–, with both resistors being 100kΩ. When the controller is enabled for Burst Mode operation, the minimum peak current in the inductor (burst clamp) is adjustable and can be programmed by the voltage on the MODE pin. Tying the MODE pin to VOUT– sets the default burst clamp to approximately 25% of the maximum sense voltage even when the voltage on the ITH pin indicates a lower value. A voltage between 0.5V and 1.0V (with respect to VOUT–) on the MODE pin programs the burst clamp linearly between 10% and 60% of the maximum sense voltage. In Burst Mode operation, if the average inductor current is higher than the load current, the error amplifier, EA, will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V (with respect to VOUT–), the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. The ITH pin is then disconnected from the output of the EA and parked at 0.450V. In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current that the LTC3896 draws to only 40μA. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA’s output begins to rise. When the output voltage 14 drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the top external MOSFET on the next cycle of the internal oscillator. When the controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator (IR) turns off the bottom external MOSFET just before the inductor current reaches zero, preventing it from reversing and going positive. Thus, the controller operates discontinuously. In forced continuous operation, the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantage of lower output voltage ripple and less interference to audio circuitry. In forced continuous mode, the output ripple is independent of load current. When the MODE pin is connected for pulse-skipping mode, the LTC3896 operates in PWM pulse-skipping mode at light loads. In this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator, ICMP, may remain tripped for several cycles and force the external top MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. At greater |VOUT–| voltages, the efficiency in pulse-skipping mode is comparable to forced continuous mode. If the PLLIN pin is clocked by an external clock source to use the phase-locked loop (see Frequency Selection and Phase-Locked Loop section), then the LTC3896 operates in forced continuous operation when the MODE pin is set to forced continuous or Burst Mode operation. The controller operates in pulse-skipping mode when clocked by an external clock source with the MODE pin set to pulse-skipping mode. 3896f For more information www.linear.com/LTC3896 LTC3896 Operation Frequency Selection and Phase-Locked Loop (FREQ and PLLIN Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. The switching frequency of the LTC3896 can be selected using the FREQ pin. If the PLLIN pin is not being driven by an external clock source, the FREQ pin can be tied to VOUT–, tied to INTVCC or programmed through an external resistor to VOUT–. Tying FREQ to VOUT– selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and VOUT– allows the frequency to be programmed between 50kHz and 900kHz, as shown in Figure 15. A phase-locked loop (PLL) is available on the LTC3896 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN pin. The LTC3896’s phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of the external top MOSFET to the rising edge of the synchronizing signal. The VCO input voltage is prebiased to the operating frequency set by the FREQ pin before the external clock is applied. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock’s to the rising edge of TG. The ability to prebias the loop filter allows the PLL to lock-in rapidly without deviating far from the desired frequency. The typical capture range of the LTC3896’s phase-locked loop is from approximately 55kHz to 1MHz, with a guarantee to be between 75kHz and 850kHz. In other words, the LTC3896’s PLL is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. It is recommended that the external clock source swing from GND (0V) to at least 2.8V. PolyPhase Applications (CLKOUT and PHASMD Pins) The LTC3896 features two pins (CLKOUT and PHASMD) that allow other controller ICs to be daisy-chained with the LTC3896 in PolyPhase applications. The clock output signal on the CLKOUT pin, which swings from VOUT– to INTVCC, can be used to synchronize additional power stages in a multiphase power supply solution feeding a single, high current output or multiple separate outputs. See the application circuit in Figure 17 for an example of how to configure two LTC3896 ICs to produce a twophase inverting regulator. Pay particular attention to the RUN, PLLIN and GND connections on the slave LTC3896. The PHASMD pin is used to adjust the phase of the CLKOUT signal. Pulling this pin to VOUT– forces CLKOUT to be out-of-phase 90° with respect to TG. Connecting this pin to INTVCC forces CLKOUT to be out of phase 120° with respect to TG. Floating this pin forces CLKOUT to be out-of-phase 180° with respect to TG. VIN + |VOUT–| Overvoltage Lockout (OVLO Pin) The LTC3896 implements a protection feature that inhibits switching when the total voltage between input and output (VIN + |VOUT–|) rises above a programmable operating range. By using a resistor divider from the input supply to VOUT–, the OVLO pin serves as a precise voltage monitor. Switching is disabled when the OVLO pin rises above 1.2V with respect to VOUT–, which can be configured to limit switching to a specific range of total voltage applied to the external MOSFETs. When switching is disabled, the LTC3896 can safely sustain VIN + |VOUT–| voltages up to the absolute maximum rating of 150V. Overvoltage events trigger a soft-start reset, which results in a graceful recovery from an input supply transient. Negative Output Overvoltage Protection An overvoltage comparator guards against transient overshoots as well as other more serious conditions that may overvoltage (in the negative direction) the output. When the VFB pin rises by more than 10% above its regulation point of 0.800V with respect to VOUT–, the top MOSFET is turned off and the bottom MOSFET is turned on until the negative overvoltage condition is cleared. 3896f For more information www.linear.com/LTC3896 15 LTC3896 Operation Power Good Pin Regulator Shutdown (REGSD) The PGOOD pin is connected to an open drain of an internal N-channel MOSFET with its drain connected to GND. The MOSFET turns on and pulls the PGOOD pin low when the VFB pin voltage is not within ±10% of the 0.8V reference voltage with respect to VOUT–. The PGOOD pin is also pulled low when the RUN pin is low (shut down). When the VFB pin voltage is within the ±10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6V with respect to GND. PGOOD is referenced to GND to allow it to interface with other external true ground-referenced components with no level shifters needed. High input voltage applications typically require using the EXTVCC LDO to keep power dissipation low. Fault conditions where the EXTVCC LDO becomes disabled (EXTVCC below the switchover threshold) for an extended period of time could result in overheating of the IC (or overheating the external N-channel MOSFET if the NDRV LDO is used). In the cases where EXTVCC is powered from the output, this event could happen during overload conditions such as a VOUT– short to ground. The LTC3896 includes a regulator shutdown (REGSD) feature that shuts down the regulator to substantially reduce power dissipation and the risk of overheating during such events. Foldback Current When the output voltage (|VOUT–|) falls to less than 70% of its nominal level, foldback current limiting is activated, progressively lowering the peak current limit in proportion to the severity of the overcurrent or short-circuit condition. Foldback current limiting is disabled during the soft-start interval (as long as the VFB voltage is keeping up with the SS voltage). Foldback current limiting is intended to limit power dissipation during overcurrent and short-circuit fault conditions. Note that the LTC3896 continuously monitors the inductor current and prevents current runaway under all conditions. SHORT-CIRCUIT EVENT The REGSD circuit monitors the EXTVCC LDO and the SS pin to determine when to shut down the regulator. Refer to the timing diagram in Figure 1. Whenever SS is above 2.2V with respect to VOUT– and the EXTVCC LDO is not switched over (the EXTVCC pin is below the switchover threshold), the internal 10μA pull-up current on SS turns off and a 5μA pull-down current turns on, discharging SS. Once SS discharges to 2.0V and the EXTVCC pin remains below the EXTVCC switchover threshold, the pull-down current reduces to 1μA and the regulator shuts down, eliminating all DRVCC switching current. Switching stays off until the SS pin discharges to approximately 200mV, at which point the 10μA pull-up current turns back on and the regulator re-enables switching. If the short-circuit persists, the regulator cycles on and off at a low duty cycle interval of about 12%. EXTVCC SWITCHOVER THRESHOLD (FALLING) SHORT REMOVED FROM VOUT– EXTVCC VOUT– ISS = –5µA (SINK) 2.2V 2.0V SS 0.8V 0.2V VOUT– TG/BG ISS = 10µA (SOURCE) ISS = –1µA (SINK) ISS = 10µA (SOURCE) START-UP INTO SHORT-CIRCUIT 3896 F01 Figure 1. Regulator Shutdown Operation 16 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information The Typical Application on the first page is a basic LTC3896 application circuit. LTC3896 can be configured to use either DCR (inductor resistance) sensing or low value resistor sensing. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs are selected. Finally, input and output capacitors are selected. Filter components mutual to the sense lines should be placed close to the LTC3896, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 2). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If DCR sensing is used (Figure 4), resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. TO SENSE FILTER NEXT TO THE CONTROLLER COUT CURRENT FLOW Current Limit Programming The ILIM pin is a three-state logic input which sets the maximum current limit of the controller. When ILIM is tied to VOUT–, the maximum current limit threshold voltage of the current comparator is programmed to be 50mV. When ILIM is floated, the maximum current limit threshold is 75mV. When ILIM is tied to INTVCC, the maximum current limit threshold is set to 100mV. SENSE+ and SENSE– Pins The SENSE+ and SENSE– pins are the inputs to the current comparator. The common mode voltage range on these pins is 0V to 65V with respect to VOUT– (absolute maximum), enabling the LTC3896 to regulate output voltages down to a nominal set point of –60V with respect to GND (allowing margin for tolerances and transients). The SENSE+ pin is high impedance over the full common mode range, drawing at most ±1μA. This high impedance allows the current comparators to be used with inductor DCR sensing. The impedance of the SENSE– pin changes depending on the common mode voltage. When SENSE– is less than INTVCC – 0.5V (with respect to VOUT–), a small current of less than 1μA flows out of the pin. When SENSE– is above INTVCC + 0.5V, a higher current (≈850μA) flows into the pin. Between INTVCC – 0.5V and INTVCC + 0.5V, the current transitions from the smaller current to the higher current. INDUCTOR OR RSENSE 3896 F02 Figure 2. Sense Lines Placement with Inductor or Sense Resistor Low Value Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 3. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX) determined by the ILIM setting. The current comparator threshold voltage sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, ΔIL. To calculate the sense resistor value, use the equation: RSENSE = VSENSE(MAX) ΔI IMAX + L 2 Normally in high duty cycle conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion operating at greater than 50% duty factor. The LTC3896, however, uses a proprietary circuit to nullify the effect of slope compensation on the current limit performance. 3896f For more information www.linear.com/LTC3896 17 LTC3896 Applications Information across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers’ data sheets for detailed information. VIN BOOST TG VOUT– SW LTC3896 SENSE+ C1* RSENSE SENSE– Using the inductor ripple current value from the Inductor Value Calculation section, the target sense resistor value is: BG VOUT– * PLACE C1 NEAR SENSE PINS RSENSE(EQUIV) = 3896 F03 Figure 3. Using a Resistor to Sense Current VIN BOOST TG VOUT– SW LTC3896 R1** R2 SENSE– DCR INDUCTOR BG To scale the maximum inductor DCR to the desired sense resistor value (RD), use the divider ratio: VOUT– * PLACE C1 NEAR SENSE PINS ** PLACE R1 NEAR INDUCTOR To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for VSENSE(MAX) in the Electrical Characteristics table. Next, determine the DCR of the inductor. When provided, use the manufacturer’s maximum value, usually given at 20°C. Increase this value to account for the temperature coefficient of copper resistance, which is approximately 0.4%/°C. A conservative value for TL(MAX) is 100°C. L SENSE+ C1* (R1||R2)C1 = L/DCR RSENSE(EQ) = DCR[R2/(R1+R2)] 3896 F04 Figure 4. Using the Inductor DCR to Sense Current Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3896 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 4. The DCR of the inductor represents the small amount of DC winding resistance of the copper, which can be less than 1mΩ for today’s low value, high current inductors. In a high current application requiring such an inductor, power loss through a sense resistor would cost several points of efficiency compared to inductor DCR sensing. If the external (R1||R2) • C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop 18 VSENSE(MAX) ΔI IMAX + L 2 RD = RSENSE(EQUIV) DCRMAX at TL(MAX) C1 is usually selected to be in the range of 0.1μF to 0.47μF. This forces R1|| R2 to around 2k, reducing error that might have been caused by the SENSE+ pin’s ±1μA current. The equivalent resistance R1|| R2 is scaled to the temperature inductance and maximum DCR: R1|| R2 = L (DCR at 20°C) • C1 The values for R1 and R2 are: R1= R1|| R2 R1• RD ; R2 = RD 1−RD 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: PLOSS R1= VIN(MAX) • |VOUT – | R1 Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. So why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET switching and gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current, ΔIL, decreases with higher inductance or higher frequency: ΔIL = ⎛ |V – | ⎞ 1 OUT ⎟ VIN ⎜⎜ (f)(L) ⎝ VIN +|VOUT – | ⎟⎠ (For more information see the Burst Clamp Programming section.) Lower inductor values (higher ΔIL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance value selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite designs have very low core loss and are preferred for high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates hard, which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET Selection Two external power MOSFETs must be selected for the LTC3896 controller: one N-channel MOSFET for the top (main) switch, and one N-channel MOSFET for the bottom (synchronous) switch. Accepting larger values of ΔIL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is ΔIL = 0.3(IMAX). The maximum ΔIL occurs at the maximum input voltage. The peak-to-peak drive levels are set by the DRVCC voltage. This voltage can range from 5V to 10V depending on configuration of the DRVSET pin. Therefore, both logiclevel and standard-level threshold MOSFETs can be used in most applications depending on the programmed DRVCC voltage. Pay close attention to the BVDSS specification for the MOSFETs as well. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below the burst clamp, which can be programmed between 10% and 60% of the current limit determined by RSENSE. The LTC3896’s ability to adjust the gate drive level between 5V to 10V (OPTI-DRIVE) allows an application circuit to be precisely optimized for efficiency. When adjusting the gate drive level, the final arbiter is the total input current for the regulator. If a change is made and the input 3896f For more information www.linear.com/LTC3896 19 LTC3896 Applications Information current decreases, then the efficiency has improved. If there is no change in input current, then there is no change in efficiency. Selection criteria for the power MOSFETs include the on-resistance RDS(ON), Miller capacitance CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers’ data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS to the gate charge curve specified VDS. When the IC is operating in continuous mode the duty cycles for the top and bottom MOSFETs are given by: |VOUT–| Main Switch Duty Cycle = VIN + |VOUT – | Synchronous Switch Duty Cycle = VIN For a given VOUT–, the maximum duty cycle occurs at minimum VIN. The MOSFET power dissipations at maximum output current are given by: PMAIN = ( ) (I OUT(MAX) VIN 2 ) 2 (1+ δ) – 3 IN + |VOUT | (V + ) ⎛ IOUT(MAX) ⎞ ⎜ ⎟(RDR )(CMILLER ) VIN 2 ⎝ ⎠ ⎡ 1 ⎤ 1 + •⎢ ⎥(f) ⎣ VDRVCC − VTHMIN VTHMIN ⎦ •RDS(ON) PSYNC = 2 VIN + |VOUT–| IOUT(MAX) (1+ δ)RDS(ON) VIN ( The term (1+ δ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs temperature curve, but δ = 0.005/°C can be used as an approximation for low voltage MOSFETs. CIN and COUT Selection VIN + |VOUT–| |VOUT –| VIN + |VOUT –| Both MOSFETs have I2R losses while the main N-channel equations include an additional term for transition losses, which are highest at high input to output differential voltages. For (VIN + |VOUT–|) < 20V the high current efficiency generally improves with larger MOSFETs, while for (VIN + |VOUT–|) > 20V the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. ) The input and output capacitance, CIN /COUT, are required to filter the square wave current through the top and bottom MOSFETs respectively. Use a low ESR capacitor sized to handle the maximum RMS current. ICIN(RMS) = ICOUT(RMS) = IOUT • |VOUT– | VIN The formula shows that the RMS current is greater than the maximum IOUT when |VOUT–| is greater than VIN. Choose capacitors with higher RMS rating with sufficient margin. Note that ripple current ratings from capacitor manufacturers are often based on only 2000 hours of life, which makes it advisable to derate the capacitor. The selection of COUT is primarily determined by the ESR required to minimize voltage ripple and load step transients. The ∆VOUT is approximately bounded by: ΔVOUT – ≤ IL(PEAK) • ESR + IOUT f • COUT where δ is the temperature dependency of RDS(ON) and RDR (approximately 2Ω) is the effective driver resistance at the MOSFET’s Miller threshold voltage. VTHMIN is the typical MOSFET minimum threshold voltage. 20 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information where IL(PEAK) is the peak inductor current and it’s given as: IL(PEAK) = + – IOUT (VIN + |VOUT |) VIN VIN • |VOUT –| 2 • L • f • (VIN + |VOUT –|) Since IL(PEAK) reach its maximum values at minimum VIN, the output voltage ripple is highest at minimum VIN and maximum IOUT. Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering and has the necessary RMS current rating. Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, specialty polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Specialty polymer capacitors offer very low ESR but have lower specific capacitance than other types. Tantalum capacitors have the highest specific capacitance, but it is important to only use types that have been surge tested for use in switching power supplies. Aluminum electrolytic capacitors have significantly higher ESR, but can be used in cost-sensitive applications provided that consideration is given to ripple current ratings and longterm reliability. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient and audible piezoelectric effects. The high Q of ceramic capacitors with trace inductance can also lead to significant ringing. When used as input capacitors, care must be taken to ensure that ringing from inrush currents and switching does not pose an overvoltage hazard to the power switch and controller. To dampen input voltage transients, add a small 5μF to 40μF aluminum electrolytic capacitor with an ESR in the range of 0.5Ω to 2Ω. High performance through-hole capacitors may also be used, but an additional ceramic capacitor in parallel is recommended to reduce the effect of lead inductance. During shutdown and startup conditions, the output capacitor can experience a small reverse voltage (a positive voltage on VOUT– with respect to GND) as the result of IC quiescent current and/or capacitor charging current flowing into the VOUT– node while VOUT– is not being actively driven negative by the converter. This reverse voltage, which is typically clamped to a diode drop above ground by the reverse diode of the external bottom MOSFET, should be carefully considered when choosing the output capacitor. Certain polarized capacitors can be permanently damaged given enough reverse voltage. If considering a polarized capacitor at the output, always consult the manufacturer if there is any question regarding reverse voltage on the capacitor. Alternatively, an all ceramic capacitor solution at the output would make the reverse voltage a non-issue Setting Output Voltage The LTC3896 output voltage is set by an external feedback resistor divider carefully placed across the output, as shown in Figure 5. The regulated output voltage is determined by: ⎛ R ⎞ VOUT – = –0.8V ⎜1+ B ⎟ ⎝ RA ⎠ To improve the frequency response, a feedforward capacitor, CFF, may be used. Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. The LTC3896 also has the option to be programmed to a fixed –5V or –3.3V output through control of the VPRG pin. Figure 6 shows how the VFB pin is used to sense ground in fixed output mode. Tying VPRG to INTVCC or VOUT– programs VOUT– to –5V or –3.3V, respectively. Floating VPRG sets VOUT– to adjustable output mode using external resistors. RB LTC3896 CFF VFB RA VOUT– 3896 F05 Figure 5. Setting Adjustable Output Voltage LTC3896 INTVCC /VOUT– VPRG VFB COUT 3896 F06 VOUT– –5V/–3.3V Figure 6. Setting Output to Fixed –5V/–3.3V Voltage 3896f For more information www.linear.com/LTC3896 21 LTC3896 Applications Information RUN Pin The LTC3896 is enabled using the RUN pin. It has a rising threshold of 1.2V with respect to GND with 80mV of hysteresis. The RUN pin is referenced to the GND pin, allowing the LTC3896 to be used with a true groundreferenced external signal or logic with no level shifters needed. Pulling the RUN pin below 1.12V shuts down the main control loop. Pulling it below 0.7V disables the controller and most internal circuits, including the DRVCC and INTVCC LDOs. In this state the LTC3896 draws only 10μA of quiescent current. The RUN pin is high impedance below 3V and must be externally pulled up/down or driven directly by logic. The RUN pin can tolerate up to 150V (absolute maximum), so it can be conveniently tied to VIN in always-on applications where the controller is enabled continuously and never shut down. Above 3V, the RUN pin has approximately a 15MΩ impedance to an internal 3V clamp. The RUN pin can be configured as an undervoltage (UVLO) lockout on the VIN supply with a resistor divider from VIN to GND, as shown in Figure 7. VIN RB LTC3896 OVLO RA VOUT– 3896 F08 Figure 8. Programming the OVLO Pin The rising and falling OVLO thresholds are calculated using the OVLO pin thresholds: ⎛ R ⎞ VOVLO(RISING) = 1.2V ⎜1+ B ⎟ ⎝ RA ⎠ ⎛ R ⎞ VOVLO(FALLING) = 1.1V ⎜1+ B ⎟ ⎝ RA ⎠ where VOVLO is the total voltage between VIN and VOUT–. VIN LTC3896 to VOUT– (Figure 8), the OVLO pin serves as a precise voltage monitor. Switching is disabled when the OVLO pin rises above 1.2V with respect to VOUT–, which can be configured to limit switching to a specific range of total voltage applied to the external switching MOSFETs. Soft-Start (SS) Pin RB RUN RA 3891 F07 Figure 7. Using the RUN Pin as a UVLO The rising and falling UVLO thresholds, referenced to ground, are calculated using the RUN pin thresholds: The start-up of VOUT– is controlled by the voltage on the SS pin. When the voltage on the SS pin is less than the internal 0.8V reference (with respect to VOUT–), the LTC3896 regulates the VFB pin voltage to the voltage on the SS pin instead of the internal reference. The SS pin can be used to program an external soft-start function. Soft-start is enabled by simply connecting a capacitor from the SS pin to VOUT–, as shown in Figure 9. An internal 10μA current source charges the capacitor, providing a linear ramping voltage at the SS pin with respect to VOUT–. The LTC3896 will regulate its feedback voltage (and hence ⎛ R ⎞ VUVLO(RISING) = 1.2V ⎜1+ B ⎟ ⎝ RA ⎠ ⎛ R ⎞ VUVLO(FALLING) = 1.12V ⎜1+ B ⎟ ⎝ RA ⎠ Overvoltage Lockout Pin (OVLO) LTC3896 The LTC3896 implements a protection feature that inhibits switching when the total voltage between input and output (VIN + |VOUT–|) rises above a programmable operating range. By using a resistor divider from the input supply 22 SS VOUT– CSS VOUT– 3896 F09 Figure 9. Using the SS Pin to Program Soft-Start 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information VOUT–) according to the voltage on the SS pin, allowing VOUT– to fall smoothly from 0V to its final regulated value. The total soft-start time will be approximately: tSS = CSS • 0.8V 10µA The SS pin also controls the timing of the regulator shutdown (REGSD) feature (as discussed in Regulator Shutdown of the Operation section). If the application does not require the use of the EXTVCC LDO (the EXTVCC pin is tied to VOUT–), the REGSD feature must be defeated with a pull-up resistor between SS and INTVCC, as shown in Figure 10. Any resistor 330kΩ or smaller between SS and INTVCC defeats the 5μA pull-down current on SS that turns on once SS reaches 2.2V with respect to VOUT– (with the EXTVCC LDO not enabled), preventing SS from discharging to 2.0V and shutting down the regulator. Note the current through this pull-up resistor adds to the internal 10μA SS pull-up current at start-up, causing the total soft-start time to be shorter than what it is calculated without the pull-up resistor. The total soft-start time with the pull-up resistor is approximately: tSS ≈ CSS • 0.8V ⎛ 4.6V ⎞ ⎜10µA + ⎟ RSS ⎠ ⎝ where RSS is the value of the resistor between the SS and INTVCC pins. INTVCC RSS LTC3896 SS CSS VOUT – VOUT– DRVCC Regulators (OPTI-DRIVE) The LTC3896 features three separate low dropout linear regulators (LDO) that can supply power at the DRVCC pin. The internal VIN LDO uses an internal P-channel pass device between the VIN and DRVCC pins. The internal EXTVCC LDO uses an internal P-channel pass device between the EXTVCC and DRVCC pins. The NDRV LDO utilizes the NDRV pin to drive the gate of an external N-channel MOSFET acting as a linear regulator with its drain connected to VIN. Note the return path for the DRVCC regulators is the VOUT– pin. The NDRV LDO provides an alternative method to supply power to DRVCC from the input supply without dissipating the power inside the LTC3896 IC. It includes an internal charge pump that allows NDRV to be driven above the VIN supply, allowing for low dropout performance. The VIN LDO has a slightly lower regulation point than the NDRV LDO, such that all DRVCC current flows through the external N-channel MOSFET (and not through the internal P-channel pass device) once DRVCC reaches regulation. When laying out the PC board, care should be taken to route NDRV away from any switching nodes, especially SW, TG, and BOOST. Coupling to the NDRV node could cause its voltage to collapse and the NDRV LDO to lose regulation. If this occurs, the internal VIN LDO would take over and maintain DRVCC voltage at a slightly lower regulation point. However, internal heating of the IC would become a concern. High frequency noise on the drain of the external NFET could also couple into the NDRV node (through the gateto-drain capacitance of the NDRV NFET) and adversely affect NDRV regulation. The following are methods that could mitigate this potential issue (refer to Figure 11a). 1.Add local decoupling capacitors to VOUT– right next to the drain of the external NDRV NFET in the PCB layout. EXTVCC 3896 F10 Figure 10. Using the SS Pin to Program Soft-Start with EXTVCC Unused/Tied to VOUT– 2.Insert a resistor (~100Ω) in series with the gate of the NDRV NFET. 3.Insert a small capacitor (~1nF) between the gate and source of the NDRV NFET. 3896f For more information www.linear.com/LTC3896 23 LTC3896 Applications Information When testing the application circuit, be sure the NDRV voltage does not collapse over the entire input voltage and output current operating range of the buck regulator. If the NDRV LDO is not being used, connect the NDRV pin to DRVCC (Figure 11b). VIN VIN NDRV R1* C2* LTC3896 C1* DRVCC VOUT– VOUT– *R1, C1, AND C2 ARE OPTIONAL 3896 F11a Figure 11a. Configuring the NDRV LDO The DRVCC supply is regulated between 5V to 10V with respect to VOUT–, depending on how the DRVSET pin is set. The internal VIN and EXTVCC LDOs can supply a peak current of at least 50mA. The DRVCC pin must be bypassed to VOUT– with a minimum of 4.7μF ceramic capacitor. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers. The DRVSET pin programs the DRVCC supply voltage and the DRVUV pin selects different DRVCC UVLO and EXTVCC switchover threshold voltages. Table 1 summarizes the different DRVSET pin configurations along with the voltage settings that go with each configuration. Table 2 summarizes the different DRVUV pin settings. Tying the DRVSET pin to INTVCC programs DRVCC to 10V. Tying the DRVSET pin to VOUT– programs DRVCC to 6V. Placing a 50kΩ to 100kΩ resistor between DRVSET and VOUT– the programs DRVCC between 5V to 10V, as shown in Figure 12. Table 1 VIN DRVSET PIN VIN 6V VOUT INTVCC 10V Resistor to VOUT– 50k to 100k 5V to 10V NDRV LTC3896 DRVCC VOUT– DRVCC VOLTAGE – Table 2 VOUT DRVUV PIN DRVCC UVLO RISING/ FALLING THRESHOLDS EXTVCC SWITCHOVER RISING/FALLING THRESHOLD VOUT– 4.0V/3.8V 4.7V/4.45V INTVCC 7.5V/6.7V 7.7V/7.45V – 3896 F11b Figure 11b. Disabling the NDRV LDO Figure 11. – All voltages with respect to VOUT 10.5 10.0 9.5 DRVCC VOLTAGE (V) 9.0 8.5 NDRV LDO or EXTVCC LDO 8.0 7.5 7.0 6.5 Internal VIN LDO 6.0 5.5 5.0 4.5 50 55 60 65 70 75 80 85 90 95 100 105 DRVSET PIN RESISTOR (kΩ) 3896 F12 Figure 12. Relationship Between DRVCC Voltage and Resistor Value at DRVSET Pin 24 Large VIN + |VOUT–| applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3896 to be exceeded. The DRVCC current, which is dominated by the gate charge current, may be supplied by the VIN LDO, NDRV LDO or the EXTVCC LDO. When the voltage on the EXTVCC pin is less than its switchover threshold (4.7V or 7.7V with respect to VOUT–, as determined by the DRVUV pin described above), the VIN and NDRV LDOs are enabled. Power dissipation in this case is highest and is equal to (VIN + |VOUT–|) • IDRVCC. If the NDRV LDO is not being used, this power is dissipated inside the IC. The gate charge current is dependent on operating frequency 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 2 of the Electrical Characteristics. For example, if DRVCC is set to 6V, the DRVCC current is limited to less than 49mA if VIN + |VOUT–| is 40V when not using the EXTVCC or NDRV LDOs at a 70°C ambient temperature: TJ = 70°C + (49mA)(40V)(28°C/W) = 125°C To prevent the maximum junction temperature from being exceeded, the VIN supply current must be checked while operating in forced continuous mode (MODE = INTVCC) at maximum VIN + |VOUT–|. When the voltage applied to EXTVCC rises above its switchover threshold (with respect to VOUT–), the VIN and NDRV LDOs are turned off and the EXTVCC LDO is enabled. The EXTVCC LDO remains on as long as the voltage applied to EXTVCC remains above the switchover threshold minus the comparator hysteresis. The EXTVCC LDO attempts to regulate the DRVCC voltage to the voltage as programmed by the DRVSET pin, so while EXTVCC is less than this voltage, the LDO is in dropout and the DRVCC voltage is approximately equal to EXTVCC. When EXTVCC with respect to VOUT– is greater than the programmed DRVCC voltage, up to an absolute maximum of 14V, DRVCC is regulated to the programmed voltage. Using the EXTVCC LDO allows the MOSFET driver and control power to be derived from the output (4.7V/7.7V ≤ |VOUT–| ≤ 14V) during normal operation and from the VIN or NDRV LDO when the output is out of regulation (e.g., start-up, short-circuit). If more current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the EXTVCC and DRVCC pins. In this case, do not apply more than 10V between the EXTVCC and VOUT– pins and make sure that EXTVCC ≤ VIN. Significant efficiency and thermal gains can be realized by powering DRVCC from the output using the EXTVCC LDO, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/ (Switcher Efficiency). For –5V to –14V regulator outputs, this means connecting the EXTVCC pin directly to ground. Tying the EXTVCC pin to ground with an –8.5V output supply reduces the junction temperature in the previous example from 125°C to: TJ = 70°C + (49mA)(8.5V)(28°C/W) = 82°C However, for –3.3V and other low voltage outputs, additional circuitry is required to derive DRVCC power from the output. The following list summarizes the four possible connections for EXTVCC: 1.EXTVCC tied to VOUT–. This will cause DRVCC to be powered from the internal VIN or NDRV LDO resulting in an efficiency penalty of up to 10% at high input voltages. If EXTVCC is tied to VOUT–, the REGSD feature must be defeated with a pull-up resistor 330kΩ or smaller between SS and INTVCC. 2.EXTVCC connected directly to ground. This is the normal connection for a –5V to –14V regulator and provides the highest efficiency. 3.EXTVCC connected to an external supply. If an external supply is available in the range 5V to 14V above VOUT–, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. Ensure that EXTVCC ≤ VIN. 4.EXTVCC connected to ground through an external Zener diode. If the output voltage is more negative than –14V, a Zener diode can be used to drop the necessary voltage between ground and EXTVCC such that EXTVCC with respect to VOUT– remains below 14V (Figure 13). In this configuration, a bypass capacitor from EXTVCC to VOUT– of at least 0.1μF is recommended. An optional resistor between EXTVCC and VOUT– can be inserted to ensure adequate bias current through the Zener diode. LTC3896 EXTVCC EXTVCC – VOUT– < 14V 0.1µF VOUT– |VOUT–| > 14V 3896 F13 Figure 13. Using a Zener Diode Between EXTVCC and Ground 3896f For more information www.linear.com/LTC3896 25 LTC3896 Applications Information INTVCC Regulator Burst Clamp Programming An additional P-channel LDO supplies power at the INTVCC pin from the DRVCC pin. Whereas DRVCC powers the gate drivers, INTVCC powers much of the LTC3896’s internal circuitry. The INTVCC supply must be bypassed with a 0.1μF ceramic capacitor to VOUT–. INTVCC is also used as a pull-up to bias other pins, such as MODE, ILIM, VPRG, etc. Burst Mode operation is enabled if the voltage on the MODE pin is 0V (with respect to VOUT–) or in the range between 0.5V to 1V. The burst clamp, which sets the minimum peak inductor current, can be programmed by the MODE pin voltage. If the MODE pin is grounded, the burst clamp is set to 25% of the maximum sense voltage (VSENSE(MAX)). A MODE pin voltage between 0.5V and 1V varies the burst clamp linearly between 10% and 60% of VSENSE(MAX) through the following equation: Topside MOSFET Driver Supply (CB) An external bootstrap capacitor CB connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. The LTC3896 features an internal 11Ω switch between DRVCC and the BOOST pin. This internal switch eliminates the need for an external bootstrap diode between DRVCC and BOOST. Capacitor CB in the Functional Diagram is charged through this internal switch from DRVCC when the SW pin is low. When the topside MOSFET is to be turned on, the driver places the CB voltage across the gate-source of the MOSFET. This enhances the top MOSFET switch and turns it on. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the BOOST voltage is above the input supply: VBOOST = VIN + VDRVCC. The value of the boost capacitor, CB, needs to be 100 times that of the total input capacitance of the topside MOSFET(s). Burst Clamp = VMODE − 0.4V • 100 1V where VMODE is the voltage on the MODE pin (with respect to VOUT–) and burst clamp is the percentage of VSENSE(MAX). The burst clamp level is determined by the desired amount of output voltage ripple at low output loads. As the burst clamp increases, the sleep time between pulses and the output voltage ripple increase. The MODE pin is high impedance and VMODE can be set by a resistor divider from the INTVCC pin to VOUT– (Figure 14a). Alternatively, the MODE pin can be tied directly to the VFB pin to set the burst clamp to 40% (VMODE = 0.8V), or through an additional divider resistor (R3). As shown in Figure 14b, this resistor can be placed below VFB to program the burst clamp between 10% and 40% (VMODE= 0.5V to 0.8V) or above VFB to program the burst clamp between 40% and 60% (VMODE = 0.8V to 1.0V). USING INTVCC TO PROGRAM THE BURST CLAMP USING VFB TO PROGRAM THE BURST CLAMP R2 LTC3896 MODE LTC3896 R2 VMODE = 0.5V TO 1.0V MODE LTC3896 R3 VMODE = 0.5V TO 0.8V VOUT– VOUT– VMODE = 0.8V TO 1.0V R3 VFB R1 R1 VOUT– R2 MODE VFB INTVCC R1 VOUT– VOUT– BURST CLAMP = 10% to 60% BURST CLAMP = 10% to 40% BURST CLAMP = 40% to 60% (14a) (14b) (14c) VOUT– 3896 F14 Figure 14. Programming the Burst Clamp 26 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information The LTC3896 includes current foldback to help limit load current when the output is overloaded or shorted to ground. If the output voltage (|VOUT–|) falls below 70% of its nominal level, then the maximum sense voltage is progressively lowered from 100% to 45% of its maximum selected value. Under short-circuit conditions with very low duty cycles, the LTC3896 will begin cycle skipping in order to limit the short-circuit current. In this situation the bottom MOSFET will be dissipating most of the power but less than in normal operation. The short-circuit ripple current is determined by the minimum on-time, tON(MIN), of the LTC3896 (≈80ns), the input voltage and inductor value: ⎛V ⎞ ΔIL(SC) = tON(MIN) ⎜ IN ⎟ ⎝ L ⎠ The resulting average short-circuit current is: 1 ISC = 45% •ILIM(MAX) − ΔIL(SC) 2 Fault Conditions: Overtemperature Protection At higher temperatures, or in cases where the internal power dissipation causes excessive self heating on chip, the overtemperature shutdown circuitry will shut down the LTC3896. When the junction temperature exceeds approximately 175°C, the overtemperature circuitry disables the DRVCC LDO, causing the DRVCC supply to collapse and effectively shutting down the entire LTC3896 chip. Once the junction temperature drops back to the approximately 155°C, the DRVCC LDO turns back on. Long term overstress (TJ > 125°C) should be avoided as it can degrade the performance or shorten the life of the part. provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. If the external clock frequency is greater than the internal oscillator’s frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP, holds the voltage at the VCO input. Note that the LTC3896 can only be synchronized to an external clock whose frequency is within range of the LTC3896’s internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. The LTC3896 is guaranteed to synchronize to an external clock that swings up to at least 2.8V and down to 0.5V or less with respect to GND. 1000 900 800 FREQUENCY (kHz) Fault Conditions: Current Limit and Current Foldback 700 600 500 400 300 200 Phase-Locked Loop and Frequency Synchronization The LTC3896 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a lowpass filter, and a voltage-controlled oscillator (VCO). This allows the turn-on of the top MOSFET to be locked to the rising edge of an external clock signal applied to the PLLIN pin. The phase detector is an edge sensitive digital type that 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (kΩ) 3896 F15 Figure 15. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin 3896f For more information www.linear.com/LTC3896 27 LTC3896 Applications Information Rapid phase-locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO’s input voltage is prebiased at a frequency corresponding to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase lock and synchronization. Although it is not required that the freerunning frequency be near the external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. The minimum on-time for the LTC3896 is approximately 80ns. However, the peak sense voltage decreases the minimum on-time gradually increases up to about 130ns. This is of particular concern in forced continuous applications with low ripple current at light loads. If the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with correspondingly larger current and voltage ripple. Table 3 summarizes the different states in which the FREQ pin can be used. When synchronized to an external clock, the LTC3896 operates in forced continuous mode at light loads if the MODE pin is set to Burst Mode operation or forced continuous operation. If the MODE pin is set to pulse-skipping operation, the LTC3896 maintains pulseskipping operation when synchronized. The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percent efficiency can be expressed as: Table 3 FREQ PIN PLLIN PIN FREQUENCY VOUT– DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor to VOUT– DC Voltage 50kHz to 900kHz Any of the Above External Clock 75kHz to 850kHz Phase Locked to External Clock Minimum On-Time Considerations Minimum on-time tON(MIN) is the smallest time duration that the LTC3896 is capable of turning on the top MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: tON(MIN) < |VOUT – | VIN +|VOUT – 1 | f • If the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. The output voltage will continue to be regulated, but the ripple voltage and current will increase. 28 Efficiency Considerations %Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3896 circuits: 1) IC VIN current, 2) DRVCC regulator current, 3) I2R losses, 4) Topside MOSFET transition losses. 1.The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 2.DRVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from DRVCC to VOUT–. The resulting dQ/dt is a current out of DRVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information Supplying DRVCC from the output through EXTVCC will scale the VIN current required for the driver and control circuits by a factor of (Duty Cycle)/(Efficiency). For example, in a 15V to –5V application, 10mA of DRVCC current results in approximately 2.5mA of VIN current. This reduces the midcurrent loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 3.I2R losses are predicted from the DC resistances of the fuse (if used), MOSFET, inductor, current sense resistor and input and output capacitor ESR. In continuous mode the average output current flows through L and RSENSE, but is chopped between the topside MOSFET and the synchronous MOSFET. If the two MOSFETs have approximately the same RDS, then the resistance of one MOSFET can simply be summed with the resistances of L, RSENSE and ESR to obtain I2R losses. For example, if each RDS(ON) = 30mΩ, RL = 50mΩ, RSENSE = 10mΩ and RESR = 40mΩ (sum of both input and output capacitance losses), then the total resistance is 130mΩ. 4.Transition losses apply only to the top MOSFET(s) and become significant only when operating at high VIN + |VOUT–| voltages (typically 20V or greater). Transition losses can be estimated from: Transition Loss = (1.7) • (VIN +|VOUT – |)3 VIN •IO(MAX) • CRSS • f Other hidden losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these system level losses during the design phase. The internal battery and fuse resistance losses can be minimized by making sure that CIN has adequate charge storage and very low ESR at the switching frequency. A 25W supply will typically require a minimum of 20μF to 40μF of capacitance having a maximum of 20mΩ to 50mΩ of ESR. Other losses including Schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT– shifts by an amount equal to ΔILOAD (ESR), where ESR is the effective series resistance of COUT. ΔILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT– to its steady-state value. During this recovery time VOUT– can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTILOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in Figure 16 circuit will provide an adequate starting point for most applications. The ITH series RC -CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly to optimize transient response once the final PC layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1μs to 10μs will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the 3896f For more information www.linear.com/LTC3896 29 LTC3896 Applications Information bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. For an inverting buck-boost converter in continuous conduction mode, the average inductor current and the inductor ripple current can be determined by the following equations: The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. ⎛ V +|V – | ⎞ IL(AVG) = IOUT ⎜⎜ IN OUT ⎟⎟ VIN ⎠ ⎝ ⎛ |V – | ⎞ 1 OUT ⎟ ΔIL = VIN ⎜ (f)(L) ⎜⎝ VIN +|VOUT – | ⎟⎠ A second, more severe transient is caused by switching in loads with large (>1μF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT–. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 • CLOAD. Thus a 10μF capacitor would require a 250μs rise time, limiting the charging current to about 200mA. Design Example As a design example, assume VIN = 7V to 22V, VOUT– = –5V, IOUT(MAX) = 5A, VSENSE(MAX) = 75mV and f = 350kHz. Tie the FREQ pin to VOUT– to program 350kHz operation. Float the ILIM pin to program a maximum current sense threshold of 75mV. From these two equations and taking a starting point of 30% ripple current at maximum inductor ripple current (at maximum VIN), the following equation can be used to calculate the inductor value: (VIN(MAX) )2 (|VOUT– |) 1 L= • (f)(0.3)(IOUT(MAX) ) (VIN(MAX) +|VOUT– |)2 = 1 (22V)2 (5V) • (350kHz)(0.3)(5A) (22V + 5V)2 ≈ 6.32µH Select a standard value of 6.2µH inductor. The resulting ripple current at minimum VIN is: ΔIL = 1 (7V)(5V) • ≈ 1.34A (350kHz)(6.2µH) (7V + 5V) The peak inductor current will be the maximum average inductor current plus one half of the ripple current. This occurs at minimum VIN and full load: IL(PEAK _ MAX) = (5A) (7V + 5V) 1.34A + ≈ 9.24A 7V 2 The minimum on-time occurs at maximum VIN: 30 tON(MIN) = |VOUT – | VIN(MAX) +|VOUT – 1 • = 529ns | f 3896f For more information www.linear.com/LTC3896 LTC3896 Applications Information The equivalent RSENSE resistor value can be calculated by using the minimum value for the maximum current sense threshold (66mV): RSENSE ≤ 66mV ≈ 0.007Ω 9.24A Choosing 1% resistors with VPRG floating: RA = 68.1kΩ and RB = 357kΩ yields an output voltage of –4.99V. Alternatively, VPRG can be connected to INTVCC and VFB tied to GND to program the –5V fixed output. The power dissipation on the topside MOSFET can be easily estimated. Choosing a Fairchild FDS6982S dual MOSFET results in: RDS(ON) = 0.035Ω/0.022Ω, CMILLER = 215pF. At maximum input voltage with T(estimated) = 50°C: PMAIN = (5V)(27V) 2 (22V) (5A)2 [1+(0.005)(50°C − 25°C)] (27V)3 5A (2.5Ω)(215pF) • 22V 2 ⎡ 1 1 ⎤ ⎢⎣ 6V − 2.3V + 2.3V ⎥⎦(350kHz) = 571mW (0.035Ω)+ A short-circuit to ground will result in a folded back current of: ISC = 34mV 1 ⎛ 80ns(22V) ⎞ − ⎜ ⎟ = 4.72A 0.007Ω 2 ⎝ 6.2µH ⎠ with a typical value of RDS(ON) and δ = (0.005/°C)(25°C) = 0.125. The resulting power dissipated in the bottom MOSFET is: PSYNC = (4.72A)2 (1.125)(0.022Ω) = 551mW which is less than under full-load conditions. CIN is chosen for an RMS current rating of at least 4.3A at temperature. COUT is chosen based on the ESR that is required to satisfy the output voltage ripple requirement. The selected COUT must support the maximum RMS operating current of 4.3A at minimum VIN. PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. 1.Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CDRVCC must return to the combined COUT (–) terminals. The path formed by the top N-channel MOSFET, bottom N-channel MOSFET and the CIN and COUT capacitors should have short leads and PC trace lengths. 2. Does the LTC3896 VFB pin’s resistive divider connect to the (-) terminal of COUT? The resistive divider must be connected between the (–) terminal of COUT and signal ground. The feedback resistor connections should not be along the high current feeds from the input or output capacitors. 3. Are the SENSE– and SENSE+ leads routed together with minimum PC trace spacing? The filter capacitor between SENSE+ and SENSE– should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the SENSE resistor. 4. Is the DRVCC and decoupling capacitor connected close to the IC, between the DRVCC and the VOUT– pin? This capacitor carries the MOSFET drivers’ current peaks. 5. Keep the SW, TG, and BOOST nodes away from sensitive small-signal nodes. All of these nodes have very large and fast moving signals and therefore should be kept on the output side of the LTC3896 and occupy minimum PC trace area. 6. Use a modified star virtual ground technique for VOUT–: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the DRVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the VOUT– pin of the IC. 3896f For more information www.linear.com/LTC3896 31 LTC3896 Applications Information PC Board Layout Debugging It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold—typically 25% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, 32 look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, the top MOSFET and the bottom MOSFET to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the GND pin of the IC. An embarrassing problem, which can be missed in an otherwise properly working switching regulator, results when the current sensing leads are hooked up backwards. The output voltage under this improper hookup will still be maintained but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor—don’t worry, the regulator will still maintain control of the output voltage. 3896f For more information www.linear.com/LTC3896 LTC3896 Typical Applications VIN 36V to 72V CINA 47µF CINB 2.2µF ×2 RPGOOD 100k MNDRV CINC 0.1µF ×3 GND PGOOD ILIM VPRG NDRV RSS 301k CINTVCC 0.1µF BG L1 47µH CSS 0.1µF FREQ OVLO EXTVCC VOUT– –48V 2A SENSE+ RSENSE 10mΩ CSNS 1nF ITH RB 590k VFB SS COUT 4.7µF 100V 2220 ×8 SW SENSE– DRVSET DRVUV MODE INTVCC MBOT CB 0.1µF LTC3896 DRVCC CDRVCC 4.7µF MTOP ×2 TG BOOST PLLIN 0V 5V VIN RUN 0V VOUT– VOUT– VOUT– VOUT– RA 10k CITHB 100pF RITH 4.99k CITHA 15nF 3896 F16 MTOP: BSC520N15NS3G MBOT: BSC019N15NS3G MNDRV: IPD320N20N3G L1: WURTH 7443634700 CINA: SUNCON 100CE47LX COUT: TDK C5750X7R2A475M230KA PINS NOT USED IN THIS CIRCUIT CLKOUT PHASMD Figure 16. High Efficiency 35V – 72V to –48V/2A Inverting Regulator 3896f For more information www.linear.com/LTC3896 33 LTC3896 Typical Applications VIN 36V to 72V CINA1 47µF CINB1 2.2µF ×2 VIN RUN 0V MTOP1 ×2 TG BOOST PLLIN COUT1 6.8µF 50V 1812 ×4 SW BG LTC3896 MNDRV1 SENSE+ DRVCC CDRV1 4.7µF RFREQ1 36.5k INTVCC_M RSS 100k SS CINT1 0.1µF CLKOUT_M CSS 0.1µF PHASMD ILIM VPRG PGOOD SENSE– FREQ EXTVCC INTVCC_M CLKOUT_M VOUT– RSENSE1 7mΩ CSNS1 1nF DEXT 12V 1W INTVCC DRVSET DRVUV MODE ITH VFB VOUT– VOUT– VOUT– VOUT– SS CLKOUT OVLO CEXT 0.1µF EXTVCC VOUT– VFB ITH RB 309k CITHB1 100pF RA 10.7k VIN RUN MTOP2 ×2 TG BOOST PLLIN MBOT2 CB2 0.1µF GND SW BG LTC3896 MNDRV2 DRVCC CDRV2 4.7µF RFREQ2 36.5k PHASMD ILIM VPRG PGOOD FREQ INTVCC DRVSET DRVUV MODE MTOP1, MTOP2: BSC440N10NS3G MBOT1, MBOT2: BSC079N10NSG MNDRV1, MNDRV2: BSC440N10NS3G L1, L2: WURTH 7443642200 CINA: SUNCON 100CE47LX COUT1, COUT2: TDK C4532X7R1H685M250kB CINT2 0.1µF L2 22µH NDRV CINC2 2.2µF SS SS CLKOUT OVLO RITH1 2k CITHA1 220nF MASTER VOUT– CINB2 2.2µF ×2 L1 22µH NDRV CINC1 2.2µF VOUT– –24V 10A MBOT2 CB1 0.1µF GND COUT2 6.8µF 50V 1812 ×4 SENSE+ SENSE– EXTVCC CSNS2 1nF EXTVCC ITH VFB VOUT– VOUT– VOUT– VOUT– RSENSE2 7mΩ ITH VFB CITHB2 100pF SLAVE 3896 F17 Figure 17. High Efficiency 2-Phase 36V–72V to –24V/10A Inverting Regulator 34 3896f For more information www.linear.com/LTC3896 LTC3896 Package Description Please refer to http://www.linear.com/product/LTC3896#packaging for the most recent package drawings. FE Package Package Variation: FE38 (31) 38-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1865 Rev B) Exposed Pad Variation AB 4.75 REF 38 9.60 – 9.80* (.378 – .386) 4.75 REF (.187) 20 6.60 ±0.10 4.50 REF 2.74 REF SEE NOTE 4 6.40 2.74 REF (.252) (.108) BSC 0.315 ±0.05 1.05 ±0.10 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.50 – 0.75 (.020 – .030) 0.09 – 0.20 (.0035 – .0079) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 19 PIN NUMBERS 23, 25, 27, 29, 31, 33 AND 35 ARE REMOVED 0.25 REF 1.20 (.047) MAX 0° – 8° 0.50 (.0196) BSC 0.17 – 0.27 (.0067 – .0106) TYP 0.05 – 0.15 (.002 – .006) FE38 (AB) TSSOP REV B 0910 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3896f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection its circuits as described herein will not infringe on existing patent rights. Forof more information www.linear.com/LTC3896 35 LTC3896 Typical Application High Efficiency 7V–72V to –12V/5A Inverting Regulator VIN 7V to 72V CINA 100µF CINB 2.2µF ×3 RPGOOD 100k 5V MNDRV CINC 2.2µF ×2 VIN RUN RNDRV 100 GND SW PGOOD VPRG DRVSET DRVUV INTVCC L1 10µH RFREQ 47.5k COUTA 22µF 25V 1812 ×8 SENSE+ RSENSE 3mΩ CSNS 1nF SENSE– PINS NOT USED IN THIS CIRCUIT: CLKOUT PHASMD PLLIN EXTVCC ITH SS FREQ CSS 0.1µF COUTB 10µF 16V 1210 ×2 BG NDRV CDRVCC 4.7µF VOUT– –12V 5A MBOT CB 0.1µF LTC3896 DRVCC CINTVCC 0.1µF MTOP TG BOOST ILIM MODE OVLO RB 140k VFB RITH 5.11k VOUTVOUTVOUTVOUT- RA 10k CITHB 47pF CITHA 4.7nF MTOP: BSC070N10NS5 MBOT: BSC040N10NS5 MNDRV: IRFR120NTRPBF L1: WURTH 7443631000 CINA: UNITED CHEMI-CON EMVY101ARA101MKE0S COUTA: TDK C4532X7R1E226M250KC COUTB: AVX 1210YD106KAT2A 3896 TA02 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3863 60V Low IQ, Inverting DC/DC Controller Fixed Frequency 50kHz to 850kHz, 3.5V ≤ VIN ≤ 60V, Negative VOUT from –0.4V to Beyond –150V , IQ = 70μA, MSOP-12E, 3mm × 4mm DFN-12 LTC7149 60V, 4A Synchronous Step-Down Regulator PLL Fixed Frequency 300kHz to 3MHz, 3.4V ≤ VIN ≤ 60V, for Inverting Outputs 0V ≤ VOUT ≤ –28V, 28-Lead (4mm × 5mm) QFN and TSSOP Packages LT8710 80V Synchronous SEPIC/ Inverting/Boost Controller Fixed Frequency Up to 750kHz, 4.5V ≤ VIN ≤ 80V, with Output Current Control TSSOP-20 Package LTC3704 Wide Input Range, No RSENSE Positive-to-Negative DC/DC Controller PLL Fixed Frequency 50kHz to 1MHz, 2.5V ≤ VIN ≤ 36V, MSOP-10 LTC3895 150V Low IQ, Synchronous Step-Down DC/DC Controller PLL Fixed Frequency 50kHz to 900kHz, 4V ≤ VIN ≤ 140V, 0.8V ≤ VOUT ≤ 60V, IQ = 40μA LTC3892/ LTC3892-1 60V Low IQ, Dual, 2-Phase Synchronous Step-Down PLL Fixed Frequency 50kHz to 900kHz, 4V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 0.99VIN, DC/DC Controller with 99% Duty Cycle Adjustable 5V to 10V Gate Drive, IQ = 29μA LTC3639 High Efficiency, 150V 100mA Synchronous StepDown Regulator Integrated Power MOSFETs, 4V ≤ VIN ≤ 150V, 0.8V ≤ VOUT ≤ VIN, IQ = 12μA, MSOP-16(12) LTC7138 High Efficiency, 140V 400mA Step-Down Regulator Integrated Power MOSFETs, 4V ≤ VIN ≤ 140V, 0.8V ≤ VOUT ≤ VIN, IQ = 12μA, MSOP-16(12) LTC3891 60V, Low IQ, Synchronous Step-Down DC/DC Controller with 99% Duty Cycle PLL Fixed Frequency 50kHz to 900kHz 4V ≤ VIN ≤ 60V, 0.8V ≤ VOUT ≤ 24V, IQ = 50μA LTC3810 100V Synchronous Step-Down DC/DC Controller Constant On-time Valley Current Mode 4V ≤ VIN ≤ 100V, 0.8V ≤ VOUT ≤ 0.93VIN, SSOP-28 LTC3638 High Efficiency, 140V 250mA Step-Down Regulator Integrated Power MOSFETs, 4V ≤ VIN ≤ 140V, 0.8V ≤ VOUT ≤ VIN, IQ = 12μA, MSOP-16(12) LTC7812 38V Synchronous Boost+Buck Controller Low EMI and Low Input/Output Ripple 4.5V (Down to 2.5V After Start-up) ≤ VIN ≤ 38V, Boost VOUT Up to 60V, 0.8V ≤ Buck VOUT ≤ 24V, IQ = 33μA, 5mm × 5mm QFN-32 LT8631 100V, 1A Synchronous Micropower Step-Down Regulator PLL Fixed Frequency 100kHz to 1MHz, 3V ≤ VIN ≤ 100V, 0.8V ≤ VOUT ≤ 60V, TSSOP-20 Package with High Voltage Spacing 36 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC3896 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LTC3896 3896f LT 0416 • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2016