MA-COM MASW-005100

Monolithic PIN SP5T Diode Switch
MASW-005100-1194
Rev 1
FEATURES
•
•
•
•
•
•
Ultra Broad Bandwidth: 50MHz to 26GHz
1.0 dB Insertion Loss
30 dB Isolation at 20GHz
Reliable.
Fully Monolithic
Glass Encapsulated Construction
DESCRIPTION
The MASW-005100-1194 is a SP5T Series-Shunt
broad band switch made with M/A-COM’s HMICTM
(Heterolithic Microwave Integrated Circuit) process,
US Patent 5,268,310. This process allows the
incorporation of silicon pedestals that form series and
shunt diodes or vias by imbedding them in a low loss,
low dispersion glass. This hybrid combination of
Silicon and Glass gives HMIC Switches exceptional
low loss and remarkable high isolation through low
millimeter-wave frequencies.
APPLICATIONS
These high performance switches are suitable for the
use in multi-band ECM, Radar, and instrumentation
control circuits where high isolation to insertion loss
ratios are required. With a standard +5 V/-5 V, TTL
controlled PIN diode driver, 50ns switching speeds are
achieved.
ABSOLUTE MAXIMUM RATINGS
TAMB = +25°C ( Unless otherwise specified )
PARAMETER
OPERATING TEMPERATURE
STORAGE TEMPERATURE
RF C.W. INCIDENT POWER
(± 20 mA )
BIAS CURRENT
( FORWARD )
APPLIED VOLTAGE
( REVERSE )
VALUE
- 65°C to +150°C
- 65°C to +175°C
+33dBm
± 20mA
- 25V
Note:
Exceeding any of these values may result in permanent
damage.
Maximum operating conditions for combination of
RF power, D.C. bias and temperature: +30dBm C.W.,
15mA per diode @+85°C
1
SP5T Monolithic Pin Diode Switch
005100-1194
MASWRev 1
TYPICAL DRIVER CONNECTIONS
CONTROL LEVEL ( DC CURRENT )
CONDITION OF RF OUTPUT
J2
J3
J4
J5
J6
J2-J1
J3-J1
J4-J1
J5-J1
J6-J1
-20 mA
+20 mA
+20 mA
+20 mA
+20 mA
Low Loss
Isolation
Isolation
Isolation
Isolation
+20 mA
-20 mA
+20 mA
+20 mA
+20 mA
Isolation
Low Loss
Isolation
Isolation
Isolation
+20 mA
+20 mA
-20 mA
+20 mA
+20 mA
Isolation
Isolation
Low Loss
Isolation
Isolation
+20 mA
+20 mA
+20 mA
-20 mA
+20 mA
Isolation
Isolation
Isolation
Low Loss
Isolation
+20 mA
+20 mA
+20 mA
+20 mA
-20 mA
Isolation
Isolation
Isolation
Isolation
Low Loss
Electrical Specifications @ TAMB = 25°C, ± 20 mA bias current
(on-wafer measurements)
RF SPECIFICATIONS
PARAMETER
FREQUENCY
INSERTION LOSS
20GHz
ISOLATION
20GHz
INPUT RETURN LOSS
MIN
28
TYP
MAX
UNITS
0.9
1.4
dB
38
dB
20GHz
22
dB
OUTPUT RETURN LOSS
20GHz
23
dB
SWITCHING SPEED
10GHz
50
nS
1
Note:
1.) Typical switching speed is measured from 10% to 90% of the detected RF voltage driven by a
TTL compatible driver. Driver output parallel RC network uses a capacitor between 390pF - 560pF
and a resistor between 150Ω - 220Ω to achieve 50ns rise and fall times.
2
SP5T Monolithic Pin Diode Switch
MASW-005100-1194
Rev 1
Typical Microwave
Performance
INSERTION LOSS
LOSS ( dB )
0.000
-0.200
-0.400
-0.600
-0.800
-1.000
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
16.0
18.0
20.0
FREQUENCY ( GHz )
J2
J3
J4
J5
J6
ISOLATION ( dB )
ISOLATION
0
-10
-20
-30
-40
-50
-60
-70
-80
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
FREQUENCY ( GHz )
J2
J3
3
J4
J5
J6
SP5T Monolithic Pin Diode Switch
MASW-005100-1194
Rev 1
Typical Microwave
Performance
LOSS ( dB )
OUTPUT RETURN LOSS
0.000
-5.000
-10.000
-15.000
-20.000
-25.000
-30.000
-35.000
-40.000
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
FREQUENCY ( GHz )
J2
J3
J4
J5
J6
INPUT RET URN LO SS
0.
-5.
-10.
-15.
LO SS -20.
(dB)
-25.
-30.
-35.
-40.
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
FREQ UENCY ( G Hz )
J2
J3
4
J4
J5
J6
18.0
20.0
SP5T Monolithic Pin Diode Switch
MASW-005100-1194
Rev 1
ASSEMBLY INSTRUCTIONS
Cleanliness
These chips should be handled in a clean environment free of organic contamination.
Electro-Static Sensitivity
The MASW-00 Series PIN switches are ESD, Class 1A sensitive (HBM). The proper ESD handling
procedures must be used.
Wire Bonding
Thermosonic wedge wire bonding using 0.003” x 0.00025” ribbon or 0.001” diameter gold wire is
recommended. A stage temperature of 150°C and a force of 18 to 22 grams should be used.
Ultrasonic energy should be adjusted to the minimum required. RF bonds should be kept as short as
possible to minimize inductance.
Mounting
These chips have Ti-Pt-Au back metal. They can be die mounted with a 80Au/20Sn or electrically
conductive Ag epoxy. Mounting surface must be flat and clean of oils and contaminants.
Eu Eutectic Die Attachment
An 80/20 gold-tin eutectic solder preform is recommended with a work surface temperature of 255°C
and a tool tip temperature of 265°C. When hot gas is applied, the tool tip temperature should be
290°C. The chip should not be exposed to temperatures greater than 320°C for more than 10
seconds. No more than three seconds should be required for the die attachment.
Epoxy Die Attachment
Assembly should be preheated to 125°C-150°C. A Controlled thickness of 2 mils is recommended for
best electrical and thermal conductivity. A thin epoxy fillet should be visible around the perimeter of the
chip after placement to ensure complete coverage. Cure epoxy per manufacturer’s recommended
schedule.
5
SP5T Monolithic Pin Diode Switch
MASW-005100-1194
Rev 1
Operation of the MASW-005100-1194 Switch
The simultaneous application of negative DC current to the Low Loss Port and positive DC current
to the remaining Isolated Ports as shown in Figure 1 achieves operation of the
MASW-005100-1194 diode switch. The backside area of the die is the RF and DC return ground
plane. The DC return is achieved on common Port J1. Constant current sources should supply the
DC control currents. The voltages at these points will not exceed + 1.5 volts (1.2 volts typical) for
supply currents up to ± 20 mA. In the Low Loss state, the Series Diode must be forward biased and
the Shunt Diode reverse biased. For all the isolated ports, the Shunt Diode is forward biased and
the Series Diode is reverse biased. The bias network design should yield >30 dB RF to DC
isolation. Best Insertion Loss, P1dB, IP3, and switching speed are achieved by using a voltage pull-up
resistor in the DC return path, ( J1 ). A minimum value of | -2V | is recommended at this return node, which is
achievable with a standard , 65V TTL controlled PIN diode driver. A typical DC bias schematic for 2-18 GHz
operation is shown in Figure 1.
2 – 18 GHz Bias Network Schematic
J1
39 pF
22 pF
DC Bias
39 pF
22 nH
100 Ω
22 nH
HMIC Switch Die
J6
22 pF
J5
J4
Fig. 1
6
J3
J2
SP5T Monolithic Pin Diode Switch
MASW-005100-1194
Rev 1
MASW-005100-1194
Chip Dimensions
A
Nominal Chip Dimensions
B
C
G
D
F
E
ORDERING INFORMATION
Part Number
Package
MASW-005100-11940W
Waffle Pack
7
DIM
INCHES
µM
A
0.068
1730
B
0.034
865
C
0.058
1480
D
0.037
945
E
0.030
750
F
0.030
750
G
0.033
825
All Pads
.005 X .005
120 X 120
Thickness
0.005
120