INTERSIL HA7

HA-5142/883
TM
Dual, Ultra Low Power Operational Amplifier
July 1994
Features
Description
• This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
The HA-5142/883 dual, ultra-low power operational amplifier
provides AC and DC performance characteristics similar to,
or better than most general purpose amplifiers while only
drawing 1/30 of the supply current of most general purpose
amplifiers. This amplifier is well suited to applications which
require low power dissipation and good electrical characteristics.
• Low Supply Current at VS = +5V. . . .(+25oC) 160µA (Max)
(Full) 200µA (Max)
• Wide Supply Voltage Range . . . . . . Single 3V to 30V or
Dual ±1.5 to ±15V
The HA-5142/883 provides accurate signal processing by
virtue of their low input offset voltage (6mV), low input bias
current (100nA), high open loop gain (20kV/V) and low noise
(20nV/√Hz). These characteristics coupled with a 1.5V/µs
slew rate and a 24kHz bandwidth make the HA-5142/883
ideal for use in low power instrumentation, audio amplifier
and active filter designs.
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 0.8V/µs (Min)
1.5V/µs (Typ)
• High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . 20kV/V (Min)
75kV/V (Typ)
• Low Noise (1kHz) . . . . . . . . . . . . . . . . . . 20nV/√Hz (Typ)
• 100% Tested at ±15V and +5V, 0V Power Supplies
Ordering Information
• Unity Gain Stable
• Dielectric Isolation
PART
NUMBER
Applications
HA7-5142/883
• Portable Instruments
HA2-5142/883
• Meter Amplifiers
HA4-5142/883
TEMPERATURE
RANGE
-55oC
to
PACKAGE
+125oC
o
8 Lead CerDIP
o
-55 C to +125 C
-55
oC
to
8 Pin Can
+125oC
20 Lead Ceramic LCC
• Telephone Headsets
• Microphone Amplifiers
• Instrumentation
• For Further Design Ideas See Application Note AN544
Pinouts
+IN1
3
V- 4
1
2
6
+
5
-IN2
+IN2
2
V+
3
NC
OUT2
8
1 20 19
OUT1 1
18
NC
17
OUT2
16
NC
7
15
-IN2
8
14
NC
NC
4
-IN1
5
NC
6
+IN1
NC
1
-+
2
+ -
NC
9
10 11 12 13
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved
149
7
1
-IN1
- +
2
+IN1
OUT2
2
+ -
3
6
5
-IN2
+IN2
4
V-
NC
7
+IN2
2
OUT 1
-IN1
V+
NC
V+
NC
8
NC
1
V-
OUT1
+
HA-5142/883
(METAL CAN)
TOP VIEW
HA-5142/883
(CLCC)
TOP VIEW
HA-5142/883
(CERDIP)
TOP VIEW
Spec Number
511035-883
FN3732.1
Specifications HA-5142/883
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 35V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VOutput Current . . . . . . . . . . . . . . . . . . . .Full Short Circuit Protection
Output Current Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
One Amplifier Shorted to Ground
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
θJC
Thermal Resistance
θJA
CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W
28oC/W
Ceramic LCC Package . . . . . . . . . . . . . .
65oC/W
15oC/W
Metal Can Package . . . . . . . . . . . . . . . . . 155oC/W
67oC/W
Package Power Dissipation Limit at +75oC for TJ ≤ +175oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870mW
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W
Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW
Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7mW/oC
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC
Metal Can Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . ±1.5V to ±15V
or 3V to 30V
VINCM ≤ 1/2 (V+ - V-)
RL ≥ 50kΩ
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: R SOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
Subscript 1 Refers to Supply Voltages (V±) = ±15V, Subscript 2 Refers to V+ = 5.0, V- = 0V
PARAMETERS
Input Offset Voltage
SYMBOL
VIO1
VIO2
Input Bias Current
+IB1
-IB1
+IB2
-IB2
Input Offset Current
IIO1
IIO2
CONDITIONS
VCM = 0V
VCM = 0V,
VOUT = 1.4V
VCM = 0V,
+RS = 10kΩ,
-R S = 100Ω
VCM = 0V,
+RS = 100Ω,
-R S = 10kΩ
VCM = 0V, VOUT =
1.4V,
+RS = 10kΩ,
-R S = 100Ω
VCM = 0V, VOUT =
1.4V,
+RS = 100Ω,
-R S = 10kΩ
VCM = 0V,
+RS = 10kΩ,
-R S = 10kΩ
VCM = 0V, VOUT =
1.4V
+RS = 10kΩ,
-R S = 10kΩ
LIMITS
GROUP A
SUBGROUPS
TEMPERATURE
1
+25oC
-6
6
µV
2, 3
+125oC, -55oC
-8
8
µV
1
+25oC
-6
6
µV
-8
8
µV
2, 3
oC,
+125
-55oC
MIN
MAX
UNITS
1
+25oC
-100
100
nA
2, 3
+125oC, -55oC
-125
125
nA
1
+25oC
-100
100
nA
o
o
2, 3
+125 C, -55 C
-125
125
nA
1
+25oC
-100
100
nA
o
o
2, 3
+125 C, -55 C
-125
125
nA
1
+25oC
-100
100
nA
-125
125
nA
2, 3
oC,
+125
-55oC
1
+25oC
-10
10
nA
2, 3
+125oC, -55oC
-20
20
nA
1
+25oC
-10
10
nA
-20
20
nA
2, 3
oC,
+125
-55oC
Spec Number
150
511035-883
Specifications HA-5142/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: R SOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
Subscript 1 Refers to Supply Voltages (V±) = ±15V, Subscript 2 Refers to V+ = 5.0, V- = 0V
PARAMETERS
Common Mode
Range
SYMBOL
+CMR1
-CMR1
+CMR2
Large Signal Voltage
Gain
+AVOL1
-AVOL1
+AVOL2
Common Mode
Rejection Ratio
+CMRR1
-CMRR1
+CMRR2
Output Voltage
Swing
+VOUT1
-VOUT1
CONDITIONS
V+ = +5V,
V- = -25V
V+ = +25V,
V- = -5V
V+ = +5V to +2V,
V- = 0V to -3V,
VOUT = 1.4V to -1.6V
VOUT = 0V and +10V,
RL = 50kΩ
VOUT = 0V and -10V,
RL = 50kΩ
VOUT = 1.4V and 2.5V,
RL = 50kΩ
∆VCM = 10V,
V+ = 5V, V- = -25V,
V OUT = -10V
∆VCM = 10V,
V+ = 25V, V- = -5V,
V OUT = ¼+10V
∆VCM = 0V to 3V,
V+ = 2V, V- = -3V,
V OUT = ¼-1.6V
RL = 50kΩ
RL = 50kΩ
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
10
-
V
10
-
V
2, 3
-VOUT2
Quiescent Power
Supply Current
(Both Amplifiers)
+ICC1
-ICC1
-ICC2
RL = 50kΩ
Terminated at 2.5V
RL = 50kΩ
Terminated at 2.5V
VOUT = 0V, IOUT =
0mA
VOUT = 0V, IOUT =
0mA
VOUT = 1.4V,
IOUT = 0mA
oC,
+125
-55oC
1
+25oC
-
-10
V
2, 3
+125oC, -55oC
-
-10
V
1
+25oC
3
-
V
3
-
V
20
-
kV/V
2, 3
4
oC,
+125
-55oC
+25oC
o
o
5, 6
+125 C, -55 C
15
-
kV/V
4
+25oC
20
-
kV/V
15
-
kV/V
20
-
kV/V
5, 6
4
o
o
+125 C, -55 C
oC
+25
o
o
5, 6
+125 C, -55 C
15
-
kV/V
1
+25oC
77
-
dB
o
o
2, 3
+125 C, -55 C
77
-
dB
1
+25oC
77
-
dB
o
o
2, 3
+125 C, -55 C
77
-
dB
1
+25oC
77
-
dB
77
-
dB
2, 3
oC,
+125
-55oC
1
+25oC
10
-
V
2, 3
+125oC, -55oC
10
-
V
1
+25oC
-
-10
V
-
-10
V
2, 3
+VOUT2
LIMITS
GROUP A
SUBGROUPS
oC,
+125
-55oC
o
1
+25 C
3.8
-
V
2, 3
+125oC, -55oC
3.5
-
V
1
+25oC
-
1
V
-
1.2
V
2, 3
oC,
+125
-55oC
o
1
+25 C
-
300
µA
2, 3
+125oC, -55oC
-
400
µA
1
+25oC
-300
-
µA
-400
-
µA
2, 3
oC,
+125
-55oC
o
1
+25 C
-
160
µA
2, 3
+125oC, -55oC
-
200
µA
Spec Number
151
511035-883
Specifications HA-5142/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
Device Tested at: R SOURCE = 100Ω, RLOAD = 500kΩ, VOUT = 0V, Unless Otherwise Specified.
Subscript 1 Refers to Supply Voltages (V±) = ±15V, Subscript 2 Refers to V+ = 5.0, V- = 0V
PARAMETERS
Power Supply
Rejection Ratio
SYMBOL
CONDITIONS
MIN
MAX
UNITS
1
+25oC
77
-
dB
77
-
dB
77
-
dB
77
-
dB
RL = 50kΩ
CS
-55oC
+125
+25oC
1
∆VSUP = +10V,
V+ = +5V, V- = 0V,
V+ = +15V, V- = 0V
-PSRR2
oC,
2, 3
∆VSUP = +10V,
V+ = +15V, V- = -10V,
V+ = +15V, V- = -20V
-PSRR1
Channel Separation
TEMPERATURE
∆VSUP = +10V,
V+ = +10V, V- = -15V,
V+ = +20V, V- = -15V
+PSRR1
LIMITS
GROUP A
SUBGROUPS
o
o
2, 3
+125 C, -55 C
1
+25oC
77
-
dB
2, 3
+125oC, -55oC
77
-
dB
1
+25oC
80
-
dB
80
-
dB
oC,
2, 3
-55oC
+125
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: RSOURCE = 50Ω, RLOAD = 50kΩ, CLOAD = 50pF, VOUT = 0V, AV = 1V/V, Unless Otherwise Specified. Subscript 1 Refers to
Supply
Voltages (V±) = ±15V; Subscript 2 Refers to V+ = 5.0V, V- = 0.0V.
PARAMETERS
Slew Rate
SYMBOL
CONDITIONS
GROUP A
SUBGROUPS
LIMITS
TEMPERATURE
MIN
MAX
UNITS
oC
+SR1
VOUT = -3V to +3V,
VIN S.R. ≤ 10V/µs
4
+25
0.8
-
V/µs
-SR1
VOUT = +3V to -3V,
VIN S.R. ≤ 10V/µs
4
+25oC
0.8
-
V/µs
+SR2
VOUT = 0V to +3V,
VIN S.R. ≤ 10V/µs
4
+25oC
0.8
-
V/µs
-SR2
VOUT = +3V to 0V,
VIN S.R. ≤ 10V/µs
4
+25oC
0.8
-
V/µs
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: RSOURCE = 50Ω, RLOAD = 50kΩ, CLOAD = 50pF, AV = 1V/V, Unless Otherwise Specified.
Subscript 1 Refers to Supply Voltages (V±) = ±15V; Subscript 2 Refers to V+ = 5.0V, V- = 0.0V.
LIMITS
PARAMETERS
Full Power Bandwidth
SYMBOL
FPBW1
FPBW2
Minimum Closed Loop
Stable Gain
Quiescent Power
Consumption
CLSG
CONDITIONS
VPEAK = 10V
VPEAK = 1.1V,
VREF = 2.5V
RL = 50kΩ, CL = 50pF
NOTES
TEMPERATURE
MIN
MAX
UNITS
1, 2
+25oC
12.7
-
kHz
1, 2
oC
115.8
-
kHz
+25
1
-55oC to +125oC
1
-
V/V
PC 1
VOUT = 0V, IOUT =
0mA
1, 3
-55oC to +125oC
-
12
mW
PC 2
VOUT = 1.4V,
IOUT = 0mA
1, 3
-55oC to +125oC
-
1
mW
NOTES:
1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation.
2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2πVPEAK).
Spec Number
3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.)
152
511035-883
HA-5142/883
Die Characteristics
DIE DIMENSIONS:
104 x 55 x 19 mils ± 1 mils
2650 x 1400 x 483µm ± 25.4µm
METALLIZATION:
Type: Al, 1% Cu
Thickness: 16kÅ ± 2kÅ
GLASSIVATION:
Type: Nitride (Si3N4) over Silox (SIO2, 5% Phos.)
Silox Thickness: 12kÅ ± 2kÅ
Nitride Thickness: 3.5kÅ ± 1.5kÅ
WORST CASE CURRENT DENSITY:
0.6 x 105A/cm 2
SUBSTRATE POTENTIAL (Powered Up): VTRANSISTOR COUNT: 72
PROCESS: Bipolar/JFET Dielectric Isolation
Metallization Mask Layout
HA-5142/883
V-
+IN2
+IN1
-IN2
OUT2
-IN1
OUT1
NC
V+
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
Spec Number
153
511035-883