672D www.vishay.com Vishay Sprague Aluminum Capacitors +105 °C, Miniature, Radial Lead FEATURES • Original SMPS output capacitors • Minimal ESR change Available • High ripple current capability • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 RIPPLE CURRENT MULTIPLIERS TEMPERATURE QUICK REFERENCE DATA DESCRIPTION VALUE AMBIENT TEMPERATURE MULTIPLIERS 0.5 Nominal case size Ø D x L in inches [mm] 0.394 x 0.472 [10.0 x 12.0] to 0.709 x 1.575 [18.0 x 40.0] +105 °C +85 °C 1.0 Operating temperature -55 °C to +105 °C +75 °C 1.25 Rated capacitance range, CR 4.7 μF to 3300 μF Tolerance on CR Rated voltage range, UR Termination Life validation test Shelf life at 105 °C DC leakage current (after 2 min charge) Revision: 14-Mar-16 FREQUENCY (Hz) -10 %, +50 % WVDC 6.3 WVDC to 250 WVDC 0 to 75 0.60 0.70 0.75 0.80 76 to 100 0.40 0.55 0.70 0.80 101 to 250 0.25 0.35 0.45 0.65 2 and 3 radial leads and axial mount. 4000 h at +105 °C ( 13.0 mm dia.): 3000 h at +105 °C (10.0 mm dia.): CAP 20 % from initial measurement. ESR 1.15 x initial specified limit. DCL initial specified limit. 500 h: CAP 10 % from initial measurement. ESR 1.15 x initial specified limit. DCL 2 x initial specified limit, (6.3 WVDC to 100 WVDC); 3 x initial specified limit, (150 WVDC to 250 WVDC). I = 0.03 CV (6.3 VDC to 100 VDC) I = 0.01 CV (150 VDC to 250 VDC) I in μA, C in μF, V in Volts 50 TO 60 100 TO 120 300 TO 400 1K TO 19K LOW TEMPERATURE PERFORMANCE CAPACITANCE RATIO C-55 °C/C+25 °C MINIMUM AT 120 Hz MAXIMUM CAPACITANCE CHANGE MAXIMUM IMPEDANCE CHANGE VOLTAGE MULTIPLIER 6.3 V to 100 V 0.75 150 V to 250 V 0.70 VOLTAGE MULTIPLIER 6.3 V to 100 V 2.5 150 V to 250 V 2.0 ESL (TYPICAL VALUES AT 1 MHz TO 10 MHz) NOMINAL DIAMETER TYPICAL ESL (nH) 0.394 [10.0] 0.512 [13.0] 0.630 [16.0] 0.709 [18.0] 4.0 7.0 10.0 12.0 Document Number: 42054 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague BULK SPECIFICATIONS in millimeters TERMINAL CODE C TERMINAL CODE D 9.5 min. S W 20 min. S L + D L W + D - - 15 min. Sleeve 7.1 min. Sleeve TERMINAL CODE J (1) TERMINAL CODE O (2) 25 min. S W L 9.5 ± 1.6 25 min. S T + D + D - NC - NC 25 min. L W 5.0 ± 1.6 Sleeve Third lead may fall within ± 20° of CL Sleeve 7.1 ± 1.6 Notes + Positive terminal - Negative terminal NC No charge potential (1) Available for 12.5 mm, 16 mm, and 18 mm diameter units (2) Available for 12.5 mm, 16 mm, and 18 mm diameter units with epoxy end-seal DIMENSIONS in inches [millimeters] CASE CODE NOMINAL D STYLES 2 AND 4 L D (max.) L (max.) STYLES 3 AND 5 D (max.) L (max.) LEAD SPACING S ± 0.024 [0.60] LEAD DIAMETER T ± 0.020 [0.50] NOMINAL AWG CC 0.394 [10.0] 0.512 [13.0] 0.413 [10.5] 0.563 [14.3] 0.413 [10.5] 0.630 [16.0] 0.197 [5.0] n/a 0.025 [0.63] 22 CD 0.394 [10.0] 0.630 [16.0] 0.413 [10.5] 0.669 [17.0] 0.413 [10.5] 0.740 [18.8] 0.197 [5.0] n/a 0.025 [0.63] 22 CG 0.394 [10.0] 0.787 [20.0] 0.413 [10.5] 0.846 [21.5] 0.413 [10.5] 0.906 [23.0] 0.197 [5.0] n/a 0.025 [0.63] 22 DG 0.492 [12.5] 0.787 [20.0] 0.512 [13.0] 0.846 [21.5] 0.512 [13.0] 0.906 [23.0] 0.197 [5.0] 0.098 [2.5] 0.032 [0.81] 20 DK 0.492 [12.5] 0.984 [25.0] 0.512 [13.0] 1.043 [26.5] 0.512 [13.0] 1.142 [29.0] 0.197 [5.0] 0.098 [2.5] 0.032 [0.81] 20 DM 0.492 [12.5] 1.043 [26.5] 0.512 [13.0] 1.102 [28.0] 0.512 [13.0] 1.161 [29.5] 0.197 [5.0] 0.098 [2.5] 0.032 [0.81] 20 DT 0.492 [12.5] 1.319 [33.5] 0.512 [13.0] 1.346 [34.2] 0.512 [13.0] 1.417 [36.0] 0.197 [5.0] 0.098 [2.5] 0.032 [0.81] 20 DS 0.492 [12.5] 1.673 [42.5] 0.512 [13.0] 1.720 [43.7] 0.512 [13.0] 1.791 [45.5] 0.197 [5.0] 0.098 [2.5] 0.032 [0.81] 20 EK 0.630 [16.0] 0.984 [25.0] 0.650 [16.5] 1.031 [26.2] 0.650 [16.5] 1.098 [27.9] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 EN 0.630 [16.0] 1.260 [32.0] 0.650 [16.5] 1.319 [33.5] 0.650 [16.5] 1.417 [36.0] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 ER 0.630 [16.0] 1.417 [36.0] 0.650 [16.5] 1.476 [37.5] 0.650 [16.5] 1.575 [40.0] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 ET 0.630 [16.0] 1.319 [33.5] 0.650 [16.5] 1.347 [34.2] 0.650 [16.5] 1.417 [36.0] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 EU 0.630 [16.0] 1.575 [40.0] 0.650 [16.5] 1.642 [41.7] 0.650 [16.5] 1.669 [42.4] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 FR 0.709 [18.0] 1.417 [36.0] 0.728 [18.5] 1.476 [37.5] 0.728 [18.5] 1.575 [40.0] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 FV 0.709 [18.0] 1.575 [40.0] 0.728 [18.5] 1.653 [42.0] 0.728 [18.5] 1.693 [43.0] 0.295 [7.5] 0.150 [3.8] 0.032 [0.81] 20 Revision: 14-Mar-16 Document Number: 42054 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague TAPE AND REEL, SPECIFICATIONS TO EIA-468D in inches [millimeters] Formed Leads P K H H0 F W0 W L1 P d D0 DIMENSIONS in inches [millimeters] AND PACKAGING QUANTITIES CASE SIZE F LEAD SPACING STD. QTY/REEL 0.236 x 0.453 [6.0 x 11.0] 0.197 [5.0] 800 0.315 x 0.472 [8.0 x 12.0] 0.197 [5.0] 700 Unformed (Straight) Leads P H F W0 W L1 d P0 D0 f DIMENSIONS in inches [millimeters] AND PACKAGING QUANTITIES CASE SIZE F LEAD SPACING STD. QTY/REEL 0.236 x 0.453 [6.0 x 11.0] 0.098 [2.5] 800 0.315 x 0.472 [8.0 x 12.0] 0.140 [3.5] (1) 700 0.394 x 0.512 [10.0 x 13.0] 0.197 [5.0] 500 0.394 x 0.630 [10.0 x 16.0] 0.197 [5.0] 500 0.394 x 0.787 [10.0 x 20.0] 0.197 [5.0] 500 Note (1) Available as special order. Revision: 14-Mar-16 Document Number: 42054 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague DIMENSIONS in inches [millimeters] ITEM d - Lead-wire diameter P - Pitch of component P0 - Feed hole pitch F - Lead-to-lead distance K - Clinch height H - Height of component from tape center H0 - Lead-wire clinch height W - Tape width W0 - Hold down tape width D0 - Feed hole diameter f - Total tape thickness L1 - Maximum lead protrusion 0.236 x 0.433 [6.0 x 11.0] 0.025 [0.63] 0.500 [12.7] 0.500 [12.7] 0.197 [5.0] 0.098 [2.5] 0.728 [18.5] 0.630 [16.0] 0.709 [18.0] 0.591 [15.0] 0.157 [4.0] 0.028 [0.7] 0.118 [3.0] CASE SIZE (DIAMETER x LENGTH) 0.315 x 0.472 0.394 x 0.512 0.394 x 0.630 [8.0 x 12.0] [10.0 x 13.0] [10.0 x 16.0] 0.025 [0.63] 0.025 [0.63] 0.025 [0.63] 0.500 [12.7] 0.500 [12.7] 0.500 [12.7] 0.500 [12.7] 0.500 [12.7] 0.500 [12.7] 0.197 [5.0] 0.197 [5.0] 0.197 [5.0] 0.157 [4.0] n/a n/a 0.787 [20.0] 0.906 [23.0] 0.906 [23.0] 0.630 [16.0] n/a n/a 0.709 [18.0] 0.709 [18.0] 0.709 [18.0] 0.591 [15.0] 0.591 [15.0] 0.591 [15.0] 0.157 [4.0] 0.157 [4.0] 0.157 [4.0] 0.028 [0.7] 0.028 [0.7] 0.028 [0.7] 0.118 [3.0] 0.118 [3.0] 0.118 [3.0] 0.394 x 0.787 [10.0 x 20.0] 0.025 [0.63] 0.500 [12.7] 0.500 [12.7] 0.197 [5.0] n/a 0.906 [23.0] n/a 0.709 [18.0] 0.591 [15.0] 0.157 [4.0] 0.028 [0.7] 0.118 [3.0] Note • Positive leader is standard. Negative leader is available by special order. ORDERING EXAMPLE Electrolytic capacitor 672D series: 672D 336 F 100 DM 5 D DESCRIPTION CODE 672D 336 F 100 DM 5 D EXPLANATION Product type Capacitance value (33 μF) Tolerance (F = - 10 % / + 50 %) Voltage rating at 105 °C (100 = 100 V) Can size (see Dimensions table) Sleeve and sealing (5 = polyester sleeve w/epoxy end seal) Terminal code / packaging (D = bulk; straight leads) Note • For lead (Pb)-free / RoHS compliant products add suffix “E3” to part number. Example: 672D336F100DM5DE3 ELECTRICAL DATA AND ORDERING INFORMATION CAPACITANCE (μF) PART NUMBER 150.0 220.0 1000.0 1500.0 3300.0 672D157F6RCD5D 672D227F6RCG5D 672D108F6REK5D 672D158F6RET5D 672D338F6RFV5D 100.0 470.0 1000.0 2200.0 672D107F012CC5D 672D477F012DM5D 672D108F012DS5D 672D228F012FV5D 100.0 470.0 1000.0 672D107F015CD5D 672D477F015DT5D 672D108F015ET5D 100.0 470.0 1000.0 672D107F020CG5D 672D477F020EK5D 672D158F020FV5D Revision: 14-Mar-16 NOMINAL CASE SIZE DxL MAX. ESR AT +25 °C () 120 Hz 20 kHz 6.3 WVDC AT 105 °C, SURGE = 9 V 0.394 x 0.630 [10.0 x 16.0] 1.10 0.70 0.394 x 0.787 [10.0 x 20.0] 0.75 0.40 0.630 x 0.984 [16.0 x 25.0] 0.16 0.09 0.630 x 1.319 [16.0 x 33.5] 0.105 0.06 0.709 x 1.575 [18.0 x 40.0] 0.075 0.045 12 WVDC AT 105 °C, SURGE = 16 V 0.394 x 0.512 [10.0 x 13.0] 1.60 0.90 0.492 x 1.043 [12.5 x 26.5] 0.31 0.16 0.492 x 1.673 [12.5 x 42.5] 0.15 0.08 0.709 x 1.575[18.0 x 40.0] 0.08 0.05 15 WVDC AT 105 °C, SURGE = 20 V 0.394 x 0.630 [10.0 x 16.0] 1.35 0.70 0.492 x 1.319 [12.5 x 35.5] 0.25 0.12 0.630 x 1.319 [16.0 x 33.5] 0.12 0.06 20 WVDC AT 105 °C, SURGE = 30 V 0.394 x 0.787 [10.0 x 20.0] 1.25 0.40 0.630 x 0.984 [16.0 x 25.0] 0.24 0.09 0.709 x 1.575 [18.0 x 40.0] 0.09 0.05 MAX. RIPPLE AT +85 °C (A) 20 kHz TO 100 kHz MAX. IMPEDANCE AT +25 °C () 100 kHz 0.50 0.70 2.05 2.90 3.40 0.60 0.33 0.085 0.055 0.045 0.40 1.35 2.35 3.30 0.70 0.12 0.06 0.05 0.50 1.75 2.90 0.50 0.11 0.055 0.70 2.00 3.25 0.35 0.085 0.05 Document Number: 42054 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague ELECTRICAL DATA AND ORDERING INFORMATION CAPACITANCE (μF) PART NUMBER 47.0 330.0 470.0 1200.0 672D476F025CC5D 672D337F025DT5D 672D477F025DS5D 672D128F025FV5D 220.0 330.0 672D227F040EK5D 672D337F040ET5D 100.0 150.0 220.0 470.0 672D107F050DT5D 672D157F050EK5D 672D227F050ET5D 672D477F050FV5D 15.0 22.0 100.0 150.0 672D156F060CD5D 672D226F060CG5D 672D107F060EK5D 672D157F060ET5D 12.0 120.0 672D126F075CD5D 672D127F075ET5D 10.0 33.0 120.0 672D106F100CD5D 672D336F100DM5D 672D127F100ET5D 4.7 15.0 47.0 672D475F200CG5D 672D156F200DT5D 672D476F200FV5D 10.0 672D106F250DT5D NOMINAL CASE SIZE DxL MAX. ESR AT +25 °C () 120 Hz 20 kHz 25 WVDC AT 105 °C, SURGE = 35 V 0.394 x 0.512 [10.0 x 13.0] 2.35 0.90 0.492 x 1.319 [12.5 x 33.5] 0.29 0.12 0.492 x 1.673 [12.5 x 42.5] 0.22 0.08 0.709 x 1.575 [18.0 x 40.0] 0.10 0.05 40 WVDC AT 105 °C, SURGE = 55 V 0.630 x 0.984 [16.0 x 25.0] 0.48 0.14 0.630 x 1.319 [16.0 x 33.5] 0.32 0.12 50 WVDC AT 105 °C, SURGE = 75 V 0.492 x 1.319 [12.5 x 33.5] 0.80 0.26 0.630 x 0.984[16.0 x 25.0] 0.55 0.22 0.630 x 1.319 [16.0 x 33.5] 0.40 0.15 0.709 x 1.575 [18.0 x 40.0] 0.25 0.09 60 WVDC AT 105 °C, SURGE = 85 V 0.394 x 0.512 [10.0 x 13.0] 7.00 2.00 0.394 x 0.787 [10.0 x 20.0] 4.60 1.20 0.630 x 0.984 [16.0 x 25.0] 0.90 0.28 0.630 x 1.319 [16.0 x 33.5] 0.60 0.18 75 WVDC AT 105 °C, SURGE = 100 V 0.394 x 0.512 [10.0 x 13.0] 8.50 2.20 0.630 x 1.319 [16.0 x 33.5] 0.68 0.18 100 WVDC AT 105 °C, SURGE = 125 V 0.394 x 0.630 [10.0 x 16.0] 10.00 2.30 0.492 x 1.043 [12.5 x 26.5] 2.55 0.55 0.630 x 1.319 [16.0 x 33.5] 0.68 0.19 200 WVDC AT 105 °C, SURGE = 250 V 0.394 x 0.787 [10.0 x 20.0] 22.50 1.95 0.492 x 1.319 [12.5 x 33.5] 7.00 0.58 0.709 x 1.575 [18.0 x 40.0] 2.30 0.18 250 WVDC AT 105 °C, SURGE = 300 V 0.492 x 1.319 [12.5 x 33.5] 12.00 1.50 MAX. RIPPLE AT +85 °C (A) 20 kHz TO 100 kHz MAX. IMPEDANCE AT +25 °C () 100 kHz 0.40 1.75 2.35 3.20 0.85 0.10 0.07 0.055 1.65 2.25 0.12 0.08 1.15 1.30 1.85 2.40 0.22 0.18 0.12 0.095 0.28 0.40 1.20 1.65 1.70 1.00 0.24 0.15 0.26 1.50 1.75 0.16 0.26 0.72 1.50 1.80 0.39 0.17 0.31 0.76 1.90 1.75 0.55 0.165 0.48 1.60 ELECTRICAL DATA AND ORDERING INFORMATION - Original ratings CAPACITANCE (μF) 150.0 220.0 680.0 1000.0 1200.0 3300.0 100.0 150.0 680.0 1000.0 2700.0 CASE CODE 6.3 WVDC AT 105 °C, SURGE = 9 V CD CG DM EK DS FV 7.5 WVDC AT 105 °C, SURGE = 10 V CC CD DT ET FV PART NUMBER 672D157H6R3CD5C 672D227H6R3CG5C 672D687H6R3DM5C 672D108H6R3EK5C 672D158H6R3ET5C 672D338H6R3FV5C 672D107H7R5CC5C 672D157H7R5CD5C 672D687H7R5DT5C 672D108H7R5ET5C 672D278H7R5FV5C Note • Capacitance tolerance code H, -10 %, +100 %; lead code C, cut leads. C lead = negative lead: 0.281" [7.1 mm], ± 0.062" [1.6 mm]; positive lead: 0375" [9.5 mm], ± 0.062" [1.6 mm]. D lead = 1.0" [25.4 mm] minimum. Revision: 14-Mar-16 Document Number: 42054 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague ELECTRICAL DATA AND ORDERING INFORMATION - Original ratings CAPACITANCE (μF) 100.0 150.0 470.0 680.0 1000.0 2200.0 100.0 150.0 470.0 680.0 820.0 1000.0 1800.0 68.0 100.0 330.0 470.0 560.0 680.0 1500.0 47.0 68.0 330.0 470.0 680.0 1200.0 47.0 220.0 330.0 390.0 820.0 22.0 100.0 150.0 180.0 220.0 470.0 15.0 22.0 68.0 100.0 120.0 150.0 390.0 CASE CODE 12 WVDC AT 105 °C, SURGE = 16 V CC CG DM DT DS FV 15 WVDC AT 105 °C, SURGE = 20 V CD CG DT EK DS ET FV 20 WVDC AT 105 °C, SURGE = 30 V CD CG DM EK DS ET FV 25 WVDC AT 105 °C, SURGE = 35 V CC CD DT DS EU FV 40 WVDC AT 105 °C, SURGE = 55 V CD EK ET DS FV 50 WVDC AT 105 °C, SURGE = 75 V CD DT EK DS ET FV 60 WVDC AT 105 °C, SURGE = 85 V CD CG DM EK DS ET FV PART NUMBER 672D107H012CC5C 672D157H012CG5C 672D477H012DM5C 672D687H012DT5C 672D108H012DS5C 672D228H012FV5C 672D107H015CD5C 672D157H015CG5C 672D477H015DT5C 672D687H015EK5C 672D827H015DS5C 672D108H015ET5C 672D188H015FV5C 672D868H020CD5C 672D107H020CG5C 672D337H020DM5C 672D477H020EK5C 672D567H020DS5C 672D687H020ET5C 672D158H020FV5C 672D476H025CC5C 672D686H025CD5C 672D337H025DT5C 672D477H025DS5C 672D687H025EU5C 672D128H025FV5C 672D476H040CD5C 672D227H040EK5C 672D337H040ET5C 672D397H040DS5C 672D827H040FV5C 672D226H050CD5C 672D107H050DT5C 672D157H050EK5C 672D187H050DS5C 672D227H050ET5C 672D477H050FV5C 672D156H060CD5C 672D226H060CG5C 672D686H060DM5C 672D107H060EK5C 672D127H060DS5C 672D157H060ET5C 672D397H060FV5C Note • Capacitance tolerance code H, -10 %, +100 %; lead code C, cut leads. C lead = negative lead: 0.281" [7.1 mm], ± 0.062" [1.6 mm]; positive lead: 0375" [9.5 mm], ± 0.062" [1.6 mm]. D lead = 1.0" [25.4 mm] minimum. Revision: 14-Mar-16 Document Number: 42054 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 672D www.vishay.com Vishay Sprague ELECTRICAL DATA AND ORDERING INFORMATION - Original ratings CAPACITANCE (μF) CASE CODE PART NUMBER 75 WVDC AT 105 °C, SURGE = 100 V 12.0 CD 672D126H075CD5C 18.0 CG 672D186H075CG5C 82.0 EK 672D826H075EK5C 120.0 ET 672D127H075ET5C 270.0 FV 672D277H075FV5C 100 WVDC AT 105 °C, SURGE = 125 V 8.2 CC 10.0 CD 672D825H100CC5C 672D106H100CD5C 33.0 DM 672D336H100DM5C 68.0 EK 672D686H100EK5C 120.0 ET 672D127H100ET5C 180.0 FV 672D187H100FV5C 150 WVDC AT 105 °C, SURGE = 200 V 6.8 CG 672D685H150CG5C 22.0 DT 672D226H150DT5C 39.0 ET 672D396H150ET5C 68.0 FV 672D686H150FV5C 200 WVDC AT 105 °C, SURGE = 250 V 4.7 CG 672D475H200CG5C 15.0 DT 672D156H200DT5C 27.0 ET 672D276H200ET5C 47.0 FV 672D476H200FV5C 250 WVDC AT 105 °C, SURGE = 300 V 8.2 DM 672D825H250DM5C 10.0 DT 672D106H250DT5C 22.0 ET 672D226H250ET5C 39.0 FV 672D396H250FV5C Note • Capacitance tolerance code H, -10 %, +100 %; lead code C, cut leads. C lead = negative lead: 0.281" [7.1 mm], ± 0.062" [1.6 mm]; positive lead: 0375" [9.5 mm], ± 0.062" [1.6 mm]. D lead = 1.0" [25.4 mm] minimum. Revision: 14-Mar-16 Document Number: 42054 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000