Setup menu General information The optional user settings of the hand-held transmitter are configured in the Setup menu. EASY Hybrid Remote B F1 F2 F3 C D F4 Calling up the Setup menu Press buttons F1+F2 simultaneously and hold for at least 5 s until the Setup symbol (5) appears on the display (B). Navigating and configuring Select menu item/setting: Use the jog wheel (D) Confirm selection: Central button (C) 1 2 3 4 Cancel and return: Press button F4 briefly 5 6 7 8 Leave the Setup menu A B C D Press button F4 and hold for at least 3 s or select the „Exit“ menu item. Parameter settings The menu items for configuration are described below. Default or reset settings are highlighted in bold. Menu item Backlight 5 IR LEARN SETUP RF B B. color Colour (1…12) B. brightn. Brightness (off, low, mid, high) B. timeout Switch-off delay time or time to return to standby (3 s, 5 s, 10 s) Nightlight Orientation lighting for the central button (external power supply required) Jog wheel basic function Default Hand-held transmitter Configuration Brightness Changing the brightness Color Change the colour/colour temperature Scenes Call up scenes Last func. Function selected last None Switch On To last state Scene 1…16 To scene A1…A16 3-channel colour control RGB+ white 3-channel colour control with white channel Warm/Cold 2-channel colour temperature control Ch-1 = warm-white channel Ch-3 = cold-white channel Scene 1…8 Scene 9…16 Sequence Sequence A…D Speed set OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg Germany All channels to 100% Channel control RGB 8-Ch. … 1-Ch. Scene set Scenes 1-8 Scenes 9-16 Scenes EASY-Hybrid-Remote_ko0908en_we1.01.indd None Switch on Last state 100% Channel set VIII 2009 Function Background lighting 8-channel/8-group- … 1-channel/1-group control Scene range A1-A8 A9-A16 Scenes that can be called up from the scene range (see "Scene set") A1…A8 (enabled=available / disabled = not available) A9…A16 Sequence A...D can be called up/cannot be called up via F3 button Speed setting Fade Time Via fade time Multiplier Via speed factor Disabled Buttons F1-Color F2-Bright F3-Play F4-Stop Jog wheel C1-On/Off Service Demo Mode Reset Exit Disabled Buttons enabled/disabled F1 F2 F3 F4 Jog wheel On/off button Start demo mode Reset the hand-held transmitter to the default settings Leave the Setup menu Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 www.osram.com www.osram.de 40083214217394 4008321421739 Page 1 of 2 A B C G D Basic settings Via DIP switches 1, 2 and 4 in the battery compartment (J). Do not change DIP switches 5-8. Function DIP switch Signal transmission type Scene storage J K Access to user settings 1 ON 2 3 4 5 6 7 Radio 1 ON ... Wired (via wall bracket) 1 OFF ... Enable 4 ON ... Disable 4 OFF ... Enable 2 ON ... Disable 2 OFF ... 8 OFF Default setting 1 ON 2 RESET of control units 3 4 5 6 7 Reset the connected control units to the default setting. 8 Set DIP switch 3 in the battery compartment (G) to OFF. OFF Press central button (C). Set DIP switch 3 to ON again. G Appendix Technical data Power supply Batteries: 3x AA/LR6 (alkaline type) 22 mm 88 mm External: 10-24 V DC / 6 VA Operating temperature 0 °C ... +40 °C Radio signal Frequency band 868.3 MHz FSK digital signal (OSRAM-specific coding) Functional range: • In the open air: Approx. 100 m 187 mm 148 mm • Building: Approx. 30 m Transmission power: Max. 10 mW Infrared signal Inference-free 38 kHz RC6 digital signal (OSRAM-specific coding) Functional range: Approx. 10-15 m 33 mm 57 mm Permissible conductor cross-section when connected via terminals Single and fine-wire conductors: 0.5 - 1.5 mm² (AWG 30 - AWG 14) Protection class III Protection type IP 20 Weight Hand-held transmitter: Approx. 120 g (without batteries) 23 mm Wall bracket: 120 g Dimensions (L x W x H) Hand-held transmitter: 187 x 57 x 23 mm Wall bracket: 148 x 33 x 88 mm Conformity with the relevant EU directives is confirmed by the CE symbol. Page 2 of 2