KBJ4005G THRU KBJ410G

SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
CURRENT
•
•
•
4.4-4.8
3.4-3.8
.1
φ3
-3 .
4
1.5-1.9
0.8-1.0
Case: molded plastic body
Terminal: Plated leads solderable per MIL-STD-750
Method 2026
Mounting position: Any (Note 4)
Mounting Torque: 6 in – 1bs max.
Weight: 0.15 ounce,4.0 gram
2.8-3.2
17.2-17.8
MECHANICAL DATA
•
•
24.8-25.2
O
9.3-9.7
3.0×45
3.6 14.7-15.3
Plastic package has UL Flammability
Glassification 94V-0
Glass passivated chip junctions
High case dielectric strength of 1500 VRMS
High surge current capability
High temperature soldering guaranteed
260℃/10 seconds, 0.375”(9.5mm) lead length
3.3-3.7
•
•
•
•
4.0 Amperes
KBJ
FEATURES
•
50 to 1000 Volts
VOLTAGE RANGE
KBJ4005G THRU KBJ410G
0.6-0.8
0.9-1.1
7.3-7.7 7.2-7.7 7.3-7.7
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
•
•
•
Ratings at 25℃ ambient temperature unless otherwise specified
Single Phase, half wave, 60Hz, resistive or inductive load
For capacitive load derate current by 20%
KBJ
SYMBOLS KBJ
VRRM
VRMS
VDC
Maximum Reverse Peak Repetitive Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward
T C=100℃(Note
Rectified Current, At
TA=40℃(Note
Peak Forward Surge Current
8.3ms single half sine wave superimposed on
rated load (JEDEC Method)
Rating for Fusing (t<8.3ms)
Maximum Instantaneous Forward Voltage drop
Per leg at 2.0A
Maximum DC Reverse Current at
rated DC blocking voltage per element
TA=25℃
TA=125℃
Typical Junction Capacitance, per let (Note 3)
Typical Thermal Resistance (Note 1)
Operating Junction Temperature Range
Storage Temperature Range
1)
2)
KBJ
KBJ
KBJ
KBJ
KBJ
4005G
401G
402G
404G
406G
408G
410G
50
35
50
100
70
100
200
140
200
400
280
400
4.0
3.0
600
420
600
800
560
800
1000
700
100
I(AV)
UNIT
Volts
Volts
Volts
Amps
IFSM
120
Amps
I2 t
60
A2s
VF
1.0
Volts
IR
5.0
500
μA
CJ
RJA
TJ
TSTG
100.0
45.0
22.0
(-55 to +150)
(-55 to +150)
Notes: 1. Unit mounted on 1.6×1.6×0.06” thick (4.0×4.0×0.15cm) AL. plate
2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length
3. Measured at 1.0 MHz and applied reverse voltage of 4.0 V
4. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum
Heat transfer with #6 screws
Web Site: www.hkmic.com
pF
℃/W
℃/W
℃
SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER
50 to 1000Volts
VOLTAGE RANGE
KBJ4005G THRU KBJ410G
CURRENT
4.0 Amperes
RATINGS AND CHARACTERISTIC CURVES KBJ4005G THRU KBJ410G
FIG. 1- DERATING CURVE
OUTPUT RECTIFIED CURRENT
150
Heat-Sink Mounting, Tc
1.6×1.6×0.06"Thk
(4.0×4.0×0.15cm) AL. Plate
PEAK FORWARD SURGE,
CURRENT,(A)
AVERAGE FORWARD OUTPUT,CURRENT
(A)
4.0
FIG. 2- MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
3.0
2.0
1.0
P.C.B. Mounting, TA
0.47×0.47" (12×12mm) Copper pads
0.375"(9.5mm) lead length
60 Hz Resistive or Inductive Load
100
50
1.0 CYCLE
0
0
0
50
100
100
NUMBER OF CYCLES AT 60 Hz
FIG. 3- TYPICAL FORWORD CHARACTERISTICS
PER LGE
FIG. 4- TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
500
INSTANTANEOUS REVERSE
CURRENT, (A)
INSTANTANEOUS FORWARD
CURRENT, (A)
10
1
150
TEMPERATURE, ℃
100
10
TJ=25℃
Pulse width=300μ
1% Duty Cycle
1
0.1
0.01
0.4
0.6
0.8
1.0
1.2
1.4
50-400V
600-1000V
100
T J =125℃
10
1
0.1
0.01
1.6
T J =25℃
0
20
40
60
80
100
INSTANTANEOUS FORWARD VOLTAGE,(V)
PERCENT OF RATED PEAK REVERSE VOLTAGE,(V)
FIG. 5- TYPICAL JUNCTION CAPACITANCE
PER LEG
FIG. 6- TYPICAL TRANSIENT THERMAL
IMPEDANCE
100
1000
T j =25℃
f=1.0MHz
Vsig=50mVp-p
TRANSIENT THERMAL IMPEDANCE
(℃/W)
JUNCTION CAPACITANCE, (pF)
TJ = T J max.
Single Sine-Wave
(JEDEC Method)
100
50-400V
600-1000V
10
0.1
1
10
1
0.1
10
100
REVRESE VOLTAGE,(V)
Web Site: www.hkmic.com
0.01
0.1
1
10
T, HEATING TIME (SEC.)
100