ACTS630MS Radiation Hardened EDAC (Error Detection and Correction) January 1996 Features Pinouts • Devices QML Qualified in Accordance with MIL-PRF-38535 • Detailed Electrical and Screening Requirements are Contained in SMD# 5962-96721 and Intersil’s QM Plan 28 PIN CERAMIC DUAL-IN-LINE, MIL-STD-1835 DESIGNATOR CDIP-T28, LEAD FINISH C TOP VIEW • 1.25 Micron Radiation Hardened SOS CMOS DEF 1 28 VCC • Total Dose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >300K RAD (Si) DB0 2 27 SEF DB1 3 26 S1 DB2 4 25 S0 DB3 5 24 CB0 23 CB1 -10 • Single Event Upset (SEU) Immunity: <1 x 10 (Typ) Errors/Bit/Day • SEU LET Threshold . . . . . . . . . . . . . . . . . . . . . . . >100 MEV-cm2/mg 11 RAD (Si)/s, 20ns Pulse DB4 6 12 RAD (Si)/s, 20ns Pulse DB5 7 22 CB2 DB6 8 21 CB3 DB7 9 20 CB4 DB8 10 19 CB5 DB9 11 18 DB15 DB10 12 17 DB14 DB11 13 16 DB13 GND 14 15 DB12 • Dose Rate Upset . . . . . . . . . . . . . . . . >10 • Dose Rate Survivability . . . . . . . . . . . >10 • Latch-Up Free Under Any Conditions • Military Temperature Range . . . . . . . . . . . . . . . . . . -55oC to +125oC • Significant Power Reduction Compared to ALSTTL Logic • DC Operating Voltage Range . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V • Input Logic Levels - VIL = 0.8V Max - VIH = VCC/2 Min • Input Current ≤ 1µA at VOL, VOH • Fast Propagation Delay . . . . . . . . . . . . . . . . 37ns (Max), 24ns (Typ) Description The Intersil ACTS630MS is a Radiation Hardened 16-bit parallel error detection and correction circuit. It uses a modified Hamming code to generate a 6-bit check word from each 16-bit data word. The check word is stored with the data word during a memory write cycle; during a memory read cycle a 22-bit word is taken form memory and checked for errors. Single bit errors in the data words are flagged and corrected. Single bit errors in check words are flagged but not corrected. The position of the incorrect bit is pinpointed, in both cases, by the 6-bit error syndrome code which is output during the error correction cycle. The ACTS630MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of a radiation hardened, high-speed, CMOS/SOS Logic Family. 28 PIN CERAMIC FLATPACK, MIL-STD-1835 DESIGNATOR CDFP3-F28, LEAD FINISH C TOP VIEW DEF DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC SEF S1 S0 CB0 CB1 CB2 CB3 CB4 CB5 DB15 DB14 DB13 DB12 The ACTS630MS is supplied in a 28 lead Ceramic Flatpack (K suffix) or a 28 Lead Ceramic Dual-In-Line Package (D suffix). Ordering Information PART NUMBER TEMPERATURE RANGE 5962F9672101VXC -55oC 5962F9672101VYC -55oC SCREENING LEVEL PACKAGE to +125oC MIL-PRF-38535 Class V 28 Lead SBDIP to +125oC MIL-PRF-38535 Class V 28 Lead Ceramic Flatpack ACTS630D/Sample 25oC Sample 28 Lead SBDIP ACTS630K/Sample 25oC Sample 28 Lead Ceramic Flatpack ACTS630HMSR 25oC Die Die CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 1 Spec Number File Number 518786 3204.1 ACTS630MS Function Tables Control Functions CONTROL ERROR FLAGS MEMORY CYCLE S1 S0 WRITE Low Low Generates Checkword Input Data READ Low High Read Data and Checkword READ High High READ High Low EDAC FUNCTION DATA I/O CHECKWORD SEF DEF Output Checkword Low Low Input Data Input Checkword Low Low Latch and Flag Error Latch Data Latch Checkword Enabled Enabled Correct Data Word and Generate Syndrome Bits Output Corrected Data Output Syndrome Bits Enabled Enabled 12 14 Check Word Generation 16-BIT DATA WORD CHECKWORD BIT 0 1 CB0 X X CB1 X X CB2 CB3 2 X X X X X CB4 3 4 X X 5 X 6 X X X 7 X 9 10 X X X X X 11 X X X X X X X X 15 X X CB5 13 X X X X 8 X X X X X X X X X X X X X NOTE: The six check bits are parity bits derived from the matrix of data bits as indicated by “x” for each bit Error Syndrome Codes ERROR LOCATIONS SYNDROME ERROR CODE 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 NO ERROR CB0 L L H L L H H H L L L H H L H H L H H H H H H CB1 L H L L H L L H L H H L H H L H H L H H H H H CB2 H L L H L L H L H L H H L H H L H H L H H H H CB3 L L L H H H L L H H L L L H H H H H H L H H H CB4 H H H L L L L L H H H H H L L L H H H H L H H CB5 H H H H H H H H L L L L L L L L H H H H H L H DB CB Error Functions TOTAL NUMBER OF ERRORS ERROR FLAGS 16-BIT DATA 6-BIT CHECKWORD SEF DEF DATA CORRECTION 0 0 Low Low Not Applicable 1 0 High Low Correction 0 1 High Low Correction 1 1 High High Interrupt 2 0 High High Interrupt 0 2 High High Interrupt Spec Number 2 518786 ACTS630MS Die Characteristics DIE DIMENSIONS: 171 mils x 159 mils 6.7µm x 6.3µm METALLIZATION: Type: Al/Si/ Metal 1 Thickness: 7.125kÅ ±1.125kÅ Metal 2 Thickness: 9kÅ ±1kÅ GLASSIVATION: Type: SiO2 Thickness: 8kÅ ±1kÅ WORST CASE CURRENT DENSITY: < 2.0 x 105A/cm2 BOND PAD SIZE: 110µm x 110µm 4.3 mils x 4.3 mils Metallization Mask Layout ACTS630MS DB2 DB1 DB0 DEF VCC SEF S1 (4) (3) (2) (1) (28) (27) (26) DB3 (5) (25) S0 DB4 (6) (24) CB0 DB5 (7) (23) CB1 DB6 (8) (22) CB2 DB7 (9) (21) CB3 DB8 (10) (20) CB4 DB9 (11) (19) CB5 (12) (13) (14) (15) (16) (17) (118) DB10 DB11 GND DB12 DB13 DB14 DB15 Spec Number 3 518786 ACTS630MS All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 Spec Number 4