Application Note, V1. 4, Sep 2012 I CE 3 A R xx8 0 C J Z CoolSET® F3R80CCM (DIP-7) brownout & CCM version Design Guide Power Management & Supply N e v e r s t o p t h i n k i n g . Published by Infineon Technologies AG 81726 Munich, Germany © 2012 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. ICE3ARxx80CJZ Revision History: Previous Version: Page 20 2012-09 V1.4 1.3 Subjects (major changes since last revision) typo error CoolSET® F3R80CCM (DIP-7) brownout & CCM version Design Guide: License to Infineon Technologies Asia Pacific Pte Ltd Kyaw Zin Min Wang Zan Kok Siu Kam Eric We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected] AN-PS0070 ICE3ARxx80CJZ Table of Contents Page 1 Introduction .............................................................................................................................. 5 2 List of Features ........................................................................................................................ 5 3 Package .................................................................................................................................... 5 4 Block Diagram .......................................................................................................................... 6 5 Typical Application Circuit ...................................................................................................... 7 6 6.1 6.1.1 6.2 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.4 6.4.1 6.4.2 6.4.3 6.5 6.6 6.6.1 6.6.2 6.6.3 6.6.4 6.6.5 6.6.6 Functional description and component design ...................................................................... 8 Startup time ............................................................................................................................... 8 Vcc capacitor ............................................................................................................................. 8 Soft Start .................................................................................................................................... 9 Low standby power - Active Burst Mode ..................................................................................... 9 Entering Active Burst Mode with selectable burst entry level ....................................................... 9 Working in Active Burst Mode................................................................................................... 11 Leaving Active Burst Mode ....................................................................................................... 12 Minimum VCC supply voltage during burst mode ....................................................................... 13 Remarks for the selection of entry/exit burst level ..................................................................... 13 Low EMI noise ......................................................................................................................... 14 Frequency jittering.................................................................................................................... 14 Soft gate drive and gate turn on resistor ................................................................................... 14 Other suggestions to solve EMI issue ....................................................................................... 14 Tight control in maximum power – (Combined OPP curve considering propagation delay & slope compensation) ......................................................................................................................... 15 Protection Features .................................................................................................................. 16 Odd skip auto restart protection mode ...................................................................................... 16 Non switch auto restart mode ................................................................................................... 16 Blanking Time for over load protection ...................................................................................... 17 Brownout Mode ........................................................................................................................ 17 User defined protection by latch enable (BRL) pin .................................................................... 19 Fast AC reset ........................................................................................................................... 20 7 Input power curve .................................................................................................................. 21 8 Layout Recommendation ....................................................................................................... 22 9 Product portfolio of CoolSET F3R80CCM (DIP-7) brownout & CCM version .................... 22 10 Useful formula for the SMPS design ..................................................................................... 23 11 Design calculation example................................................................................................... 25 12 References ............................................................................................................................. 28 13 Appendix 1 – reference circuit to solve output OVP by external voltage short .................. 29 ® Application Note 4 2012-09-27 ICE3ARxx80CJZ 1 Introduction The CoolSET®-F3R80CCM, ICE3ARxx80CJZ is the latest development of the CoolSET® in continuous conduction mode (CCM) operation. It is a PWM controller with power MOSFET and startup cell in a DIP-7 package. The switching frequency is running at 100 kHz and it targets for DVD player, set-top box, portable game console, white goods, auxiliary power supply for server/PC, etc. The ICE3ARxx80CJZ adopts the BiCMOS technology and provides a wider Vcc operating range up to ® 24.7V. It inherits the proven good features of CoolSET -F3R such as Active Burst Mode, propagation delay compensation, soft gate drive, auto restart protection for major faults (Vcc over voltage, over load, open loop Vcc under voltage, short optocoupler and over temperature), it also has the selectable entry and exit burst mode level, brownout feature, built-in soft start time, built-in blanking time for short duration peak power, frequency jitter feature, slope compensation for CCM operation, external latch enable and fast AC reset, etc. The particular features need to be stressed are 800V MOSFET, CCM/DCM operation, fixed voltage Brownout detect/reset, fast AC reset, the best-in-class low standby power and the good EMI performance. 2 List of Features 800V avalanche rugged CoolMOS® with Startup Cell Active Burst Mode for lowest Standby Power Slope compensation for CCM operation Selectable entry and exit burst mode level 100kHz internally fixed switching frequency with jittering feature Auto Restart Protection for Over load, Open Loop, VCC Under/Over voltage and Over temperature External latch enable pin and fast AC reset Over temperature protection with 50°C hysteresis Built-in 10ms Soft Start Built-in 40ms blanking time for short duration peak power Propagation delay compensation for both maximum load and burst mode Brownout feature BiCMOS technology for low power consumption and wide VCC voltage range Soft gate drive with 50Ω turn on resistor 3 Package The package for F3R80CCM ICE3ARxx80CJZ brownout and frequency jitter mode product is DIP-7. Figure 1 Pin configuration Application Note Pin Name 1 BRL Brownout, fast AC Reset & Latch enable 2 FBB Feedback & Burst entry/exit control 3 CS Current Sense/800V CoolMOS Source 4 n.c not connected 5 Drain 6 - 7 VCC Controller Supply Voltage 8 GND Controller Ground 5 Description ® ® 800V CoolMOS Drain (no pin) 2012-09-27 ICE3ARxx80CJZ 4 Block Diagram Figure 2 Application Note Block Diagram of ICE3ARxx80CJZ 6 2012-09-27 ICE3ARxx80CJZ 5 Typical Application Circuit (circuit with output OVP latch, brownout and fast AC reset features, etc.) Figure 3 Application Note Typical application circuit with ICE3AR10080CJZ 10W 5V 7 2012-09-27 ICE3ARxx80CJZ 6 Functional description and component design 6.1 Startup time Startup time is counted from applying input voltage to IC turn on. ICE3ARxx80CJZ has a startup cell which is connected to input bulk capacitor. When there is input voltage, the startup cell will act as a constant current source to charge up the Vcc capacitor and supply energy to the IC. When the Vcc capacitor reaches the Vcc_on threshold 17V, the IC turns on. Then the startup cell is turned off and the Vcc is supplied by the auxiliary winding. Start up time is independent from the AC line input voltage and it can be calculated by the equation (1). Figure 4 shows the start up time of 85Vac line input. where, IVCCcharge : average current of IVCCcharge2 and IVCCcharge3 ( 0.875mA ), VVCCon : IC turns on threshold ( 17V ), CVCC : Vcc capacitor Please refer to the datasheet for the symbol used in the equation. 250ms Channel Channel Channel Channel 1; C1 : Drain voltage (VD) 2; C2 : Supply voltage (VCC) 3; C3 : Feedback voltage (VFBB) 4; C4 : BRL voltage (VBRL) Measured startup time = 0.25s Entry/exit burst selection (Level 2) Startup @ 85Vac & max. load Figure 4 The startup delay time at AC line input voltage of 85Vac Pre-caution : For a typical application, start up should be VCC ramps up first, other pin (such as FBB pin) voltage will follow VCC voltage to ramp up. It is recommended not to have any voltage on other pins (such as FBB; BRL and CS) before VCC ramps up. In addition, the dummy load in the Vcc pin should be larger than 150KΩ. Otherwise, it would have a risk of delay startup. 6.1.1 Vcc capacitor The minimum value of the Vcc capacitor is determined by voltage drop during the soft start time. The formula is expressed in equation (2). where, IVCCsup2_max tss VCChys Application Note : supply current with active gate ( 4.8mA for ICE3AR10080CJZ) : soft start time ( 10ms ) : Vcc turn-on/off hysteresis voltage ( 6.5V ) 8 2012-09-27 ICE3ARxx80CJZ Therefore, the minimum Vcc capacitance can be 4.9μF. In order to give more margins, 10uF is taken for the design. The startup time tStartUp is then 0.19s. The measured start up time is 0.25s (Figure 4). A 0.1uF filtering capacitor is always needed to add as near as possible to the Vcc pin to filter the high frequency noise. 6.2 Soft Start When the IC is turned on after the startup time, a digital soft start circuit is activated. A gradually(32 steps) increased soft start voltage is emitted by the digital soft start circuit, which in turn releases the duty cycle gradually increase from zero. The duty cycle increases to maximum (which is limited by the transformer design) at the end of the soft start period. When the soft start time ends, IC goes into normal mode and the duty cycle is controlled by the FB signal. The soft start time is set at 10ms for maximum load. The soft start time is load dependent; shorter soft start time with lighter load. Figure 5 shows the soft start behavior at 85Vac input and maximum load. The primary peak current increases slowly to the maximum in the soft start period. 9.5ms Channel Channel Channel Channel 1; C1 : Current sense voltage (VCS) 2; C2 : Supply voltage (VCC) 3; C3 : Feedback voltage (VFBB) 4; C4 : BRL voltage (VBRL) Soft Start time = 9.5ms(32 steps) Soft start @ Vin=85Vac & max. load Figure 5 6.3 Soft start at AC line input voltage of 85 Vac & full load Low standby power - Active Burst Mode The IC will enter Active Burst Mode function at light load condition which enables the system to achieve the lowest standby power requirement of less than 100mW. Active Burst Mode means the IC is always in the active state and can therefore immediately response to any changes on the FB signal, VFB. 6.3.1 Entering Active Burst Mode with selectable burst entry level Because of the current mode control scheme, the feedback voltage VFB actually controls the power delivery to output. An important relationship between the VCS and the VFB is expressed in equation (3). VFB (VMc Vcs ) Av VOffset Ramp ( M C ton Rcs Ip ) Av VOffset Ramp where, VCS AV VOffset-Ramp :current sense voltage :PWM OP gain (3.25) :voltage ramp offset (0.6V) MC :slope compensation rate (50mV/µs) ton :switch on time Rcs Ip :current sense resistor Application Note (3) :transformer primary current 9 2012-09-27 ICE3ARxx80CJZ When the output load reduces, the feedback voltage VFB drops. If the VFB stays below VFB_burst for 20ms, the IC enters into the Active Burst Mode. The threshold power to enter burst mode is expressed in equation (4). where, Lp : transformer primary inductance IP _ burst : transformer primary current to enter burst mode fs where, : switching frequency Vdc VFB_burst :dc input voltage : feedback level to enter burst mode Figure 6 Burst mode detect and adjust ® In enhancement to CoolSET -F3R, user can select the burst mode entry and exit level in CoolSET® F3R80CCM, according to the application by adding different values of Rsel (R113) resistor at FBB pin. The IC would detect the voltage level at the FBB pin within the VCC charging time from 8V to 17V. During that detection time, the current source Isel (3.5µA) current will charge the Rsel (R113) resistor. Based on the voltage level, the IC will select burst mode entry and exit level. There are 3 different levels of burst mode available and the following table is the recommended resistance range of the Rsel (R113) resistor for the entry and exit burst level. Entry level Level Rsel VFBB 1 2 3 <405kΩ 685kΩ~900kΩ >1530kΩ VFBB < Vref1 (1.8V) Vref1 (1.8V) <VFBB < Vref2 (4V) VFBB > Vref2 (4V) % of Pin_max 5% 10% 15% VFB_burst 1.29V 1.61V 1.84V Exit level % of Pin_max 11% 20% 27% Vcsth_burst 0.21V 0.29V 0.34V Figure 7 shows the waveform with the load drops from nominal load to light load. After the 20ms blanking time IC goes into burst mode. Application Note 10 2012-09-27 ICE3ARxx80CJZ Channel Channel Channel Channel 19ms 1; C1 : Current sense voltage (VCS) 2; C2 : Supply voltage (VCC) 3; C3 : Feedback voltage (VFBB) 4; C4 : BRL voltage (VBRL) Entering Active Burst mode with built-in blanking time 20ms when load changes from full to light @ Vin=85Vac Figure 7 Entering active burst mode 6.3.2 Working in Active Burst Mode In the active burst mode, the IC is constantly monitoring the output voltage by feedback pin, VFBB, which controls burst duty cycle and burst frequency. The burst “ON” starts when VFB reaches 3.5V and it stops when VFB is dropped to 3.2V. During burst “ON”, the primary current limit is reduced to Vcsth_burst ( 27% ~ 44% of maximum peak current ) to reduce the conduction losses and to avoid audible noise. The FB voltage is swinging like a saw tooth between 3.2V and 3.5V. The corresponding secondary output ripple (peak to peak) is controlled to be small. It can be calculated by equation (6). where, Ropto Rfb Gopto GTL431 :series resistor with opto-coupler at secondary side (e.g. R22 in Figure 3) :IC internal pull up resistor connected to FB pin (Rfb=15.4KΩ) :current transfer gain of opto-coupler :voltage transfer gain of the loop compensation network (e.g. R22, R211, R24, R25, R26, R27, C25, C26 in Figure 3) Vfb : feedback voltage change (0.3V) Figure 8 is the output ripple waveform of the 10W 5V demo board. The burst ripple voltage is about 19mV. Channel 1; C1 : Output ripple voltage (Vo) Channel 2; C2 : Output current (Io) Vripple_pk_pk=19mV Probe terminal end with decoupling capacitor of 0.1uF(ceramic) & 1uF(electrolytic), 20MHz filter Output ripple voltage @ 85Vac and 1W load Figure 8 Application Note Output ripple during Active Burst Mode at light load 11 2012-09-27 ICE3ARxx80CJZ 6.3.3 Leaving Active Burst Mode When the output load increases to be higher than the maximum exit level of burst mode, Vout will drop a little and VFB will rise up fast to exceed 4.0V. The system leaves burst mode immediately when VFB reaches 4.0V. Once system leaves burst mode, the current sense voltage limit is set to Vcsth1 or Vcsth2 according the input AC line voltage, the feedback voltage VFBB swings back to the normal control level. The leaving burst power threshold (i.e. maximum power to be handled during burst operation) is expressed in equation (7). However, the actual power can be higher as it would include propagation delay time. where, Vcsth _ burst : peak current in the burst mode Vcsth : maximum current limit threshold at CS pin Pin_max : maximum input power RCS : current sense resistor Lp : primary inductance of transformer The leave burst mode timing diagram is shown in Figure 9. 4.0V 3.5V V FB 3.2V Vout Vout_AV Vout_drop_max Vcsth V CSth_burst Figure 9 Vout_drop during leaving burst mode The maximum output drop during the transition can be estimated in equation (8). Figure 10 is the captured waveform when there is a load jump from light load to full load. The output ripple drop during the transition is about 71mV. Application Note 12 2012-09-27 ICE3ARxx80CJZ Channel 1; C1 : Current sense voltage (VCS) Channel 3; C3 : FB voltage (VFBB) Channel 4; C4 : Output ripple voltage (Vo) 71mV Leaving Active Burst mode when load change from light to full @ Vin=85Vac Figure 10 Leaving burst mode waveform 6.3.4 Minimum VCC supply voltage during burst mode It is particularly important that the Vcc voltage must stay above VVCCoff (i.e. 10.5V). Otherwise, the expected low standby power cannot be achieved. The IC will go into auto-restart mode instead. A reference Vcc circuit is presented in Figure 3. This is for a low cost transformer design where the transformer coupling is not too good. Thus the circuit R13 and ZD11 is added to clamp the Vcc voltage exceeding 25.5V in extreme case such as high load and the Vcc OVP protection is triggered. If the transformer coupling is good, this circuit is not needed. 6.3.5 Remarks for the selection of entry/exit burst level The selection of the entry/exit burst level will depend on the actual application. The below table is the remarks for the selection. Rsel <405kΩ 685kΩ<900kΩ >1530kΩ Application Note Remarks Lowest entry/exit burst level: good for very small standby load. It needs to take care CS pin noise to be as small as possible as it would have a chance of unstable burst mode (rapid entry and exit burst mode). In case of unstable, it is better to add noise filtering capacitor (e.g., 100nF ceramic cap) in between CS (pin 3) and Gnd (pin 8). However, adding filtering cap would increase maximum overload power and widen the burst mode entry and exit power. Besides, it can also be improved by reducing the loop gain by increasing the opto-coupler biasing resistor, R22. However, if the gain is too low, it would result in higher output ripple. 2nd highest entry/exit burst level: good for general application. It needs to take care CS pin noise to be as small as possible as it would have a chance of unstable burst mode (rapid entry and exit burst mode). In case of unstable, it is better to add noise filtering capacitor (e.g., 100nF ceramic cap) in between CS (pin 3) and Gnd (pin 8). However, adding filtering cap would increase maximum overload power and widen the burst mode entry and exit power. Besides, it can also be improved by reducing the loop gain by increasing the opto-coupler biasing resistor, R22. However, if the gain is too low, it would result in higher output ripple. Highest entry/exit burst level: highest burst power, good for larger standby load. It needs to take care of not having too high loop gain as it would have a chance of unstable burst mode (rapid entry and exit burst mode). In case of unstable, the easiest way is to reduce the loop gain by increasing the opto-coupler biasing resistor, R22. However, too low loop gain would result to higher output ripple. 13 2012-09-27 ICE3ARxx80CJZ 6.4 Low EMI noise 6.4.1 Frequency jittering The IC is running at a fixed frequency of 100kHz with jittering frequency at +/-4% in a switching modulation period of 4ms. This kind of frequency modulation can effectively help to obtain a low EMI noise level particularly for conducted EMI. The jittering frequency measured for ICE3AR10080CJZ is 96 KHz ~ 104 KHz (refer to Figure 11). Channel 1; C1 : Drain voltage (VD) 102kHz 3.8ms Frequency jittering from 95 kHz ~ 102 kHz, 95kHz Frequency jittering @ 85Vac and max. load Figure 11 Switching frequency jittering 6.4.2 Soft gate drive and gate turn on resistor The gate soft driving is to split the gate driving slope into two, so that the CoolMOS® turns on speed is relatively slower comparing to a single slope drive (see Figure 12). Besides soft gate drive, it is also implemented with 50Ω gate turn on resistor. In this way, the high ΔI/Δt noise is greatly reduced and the noise signal reflected in the EMI spectrum is also reduced. (internal) VGate typ. t = 160ns 4.6V t Figure 12 Soft gate drive waveform 6.4.3 Other suggestions to solve EMI issue Some more suggestions to improve the EMI performance are listed below. 1. Add RCD clamper circuit to the primary winding of the transformer: RCD clamper circuit (D11, R11 & C15) can absorb the current due to leakage inductance of transformer during switch off time of the MOSFET, so voltage spike of the drain can clamp to desired voltage level and suppress the EMI noise (refer to Figure 3). 2. Add capacitor (CDS) at the drain source pin: CDS (C110) can slow down the turn off speed of the MOSFET and the high ΔV/Δt noise will be reduced and so is the EMI noise. The drawback is more energy will be dissipated due to slower turn off speed of MOSFET (refer to Figure 3). 3. Add snubber circuit to the output rectifier: Most of the radiated EMI noise comes out from the output of the system especially for a system with output cable. Adding snubber circuit (R21 and C21) to the output rectifier is a more direct way to suppress those EMI noise (refer to Figure 3). Application Note 14 2012-09-27 ICE3ARxx80CJZ 4. Reduce the reflection voltage: if the secondary to primary reflection voltage is reduced, the switching voltage at drain can also be reduced. Hence the voltage switching noise is reduced and so is the EMI noise. The drawback is the reverse voltage of the secondary rectifier will increase. 6.5 Tight control in maximum power – (Combined OPP curve considering propagation delay & slope compensation) The maximum power of the system is changed with the different AC line input voltage, the higher the input AC line voltage, the higher the maximum power and vice versa. This is due to the propagation delay of the IC for DCM converters and the propagation delay plus CCM characteristic for CCM converters. In this ICE3ARxx80CJZ, two different types of compensation have implemented to reduce maximum power difference between low and high line. One is for switch on time lower than 4µs (DCM) and the other one is for switch on time higher than 4µs (CCM). The propagation delay compensation is realized by means of a dynamic threshold voltage. In case of a steeper slope, the switch off time of the driver is earlier to compensate the delay. Figure 13 Propagation delay compensation curve Figure 14 Application Note Dynamic voltage threshold 15 2012-09-27 ICE3ARxx80CJZ 6.6 Protection Features Protection is one of the major factors to determine whether the system is safe and robust. Therefore sufficient protection is necessary. ICE3ARxx80CJZ provides two kinds of protection mode; odd skip auto restart mode and non switch auto restart mode. A list of protections and the failure conditions are shown in the following table. Protection function Failure condition Protection Mode VCC over voltage VCC > 25.5V & last for 120µs Odd skip auto restart Over load VFBB > 4.5V & 40ms blanking time Odd skip auto restart Open loop Same as over load Odd skip auto restart VCC under voltage VCC < 10.5V Normal auto restart Short opto-coupler -> VCC under voltage Normal auto restart Over temperature (controller junction) TJ > 130°C ( recovered with 50°C hysteresis) Non switch Auto restart External protection enable VBRL < 0.4V & last for 210 µs Latch 6.6.1 Odd skip auto restart protection mode When the failure condition meets the odd skip auto restart protection mode, the IC will enter into odd skip auto restart. The switching pulse will stop. Then the Vcc voltage will drop. When the Vcc voltage drops to 10.5V, the startup cell will turn on again. The Vcc voltage is then charged up until 17V. Unlike auto restart mode, there is no detect of fault and no switching pulse for the first (odd number) restart cycle. At the second (even number) of restart cycle, the fault detects and soft start switching pulses maintained. If the fault persists, it would continue the auto-restart mode. However, if the fault is removed, it can release to normal operation only at the even number auto restart cycle. The main purpose of the odd skip auto restart is to extend the restart time such that the power loss during auto restart protection can be reduced. This feature can allow adopting smaller VCC capacitor where the restart time is shorter. Figure 15 shows the odd skip auto restart switching waveform of the VCC and VCS. No detect of fault and no switching pulse for the first and odd restart cycle and there are fault detect and soft start switching pulses at the second and even restart cycle. VVCC Fault detected No detect Startup and detect No detect 17V 10.5V VCS t t Figure 15 Odd skip auto restart mode 6.6.2 Non switch auto restart mode Non switch auto restart mode is similar to odd skip auto restart mode except the start up switching pulses are also suppressed at the even number of the restart cycle. The detection of fault still remains at the even number of the restart cycle. When the fault is removed, the IC will resume to normal operation at the even number of the restart cycle (Figure 16). Application Note 16 2012-09-27 ICE3ARxx80CJZ Fault detected VVCC No detect Startup and detect No detect 17V 10.5V VCS t No switching t Figure 16 Non switch auto restart mode 6.6.3 Blanking Time for over load protection The IC controller provides a blanking window before entering into the odd skip auto restart mode due to output overload/short circuit. The purpose is to ensure that the system will not enter protection mode unintentionally. The built-in blanking time is set at 40ms. Channel Channel Channel Channel 1; C1 : Current sense voltage (VCS) 2; C2 : Supply voltage (VCC) 3; C3 : Feedback voltage (VFBB) 4; C4 : BRL voltage (VBRL) Blanking time =38.27ms built-in 40ms blanking Figure 17 Over load protection with built-in blanking time @ 85Vac blanking window for over load protection 6.6.4 Brownout Mode When the AC line input voltage is lower than the designed voltage range, brownout mode is detected by sensing the voltage level at BRL pin through the voltage divider resistors from the separate AC hold up circuit (to get the stabilize voltage at BRL pin, brownout sense voltage should not take from bulk capacitor directly as the ripple voltage of bulk capacitor is big and varied with load). Once the voltage level at BRL pin falls below 1V for 270µs, the controller stops switching and enters into brownout mode. It is until the input AC level goes up to the designed voltage range, BRL voltage is higher than 1.25V and the Vcc hits 17V, the brownout mode is released. Unlike DCM CoolSET® ICE3xRXX80JZ, which sense the voltage and charging current for hysteresis, this CCM CoolSET® ICE3ARXX80CJZ only sense the voltage level. As a result, the brownout resistors can be in bigger resistance and hence lower the standby power especially in high line. Note that there is no MOSFET switching but it always detect brownout level in every restart cycle during brownout mode (Figure 18). Figure 18 Application Note Brownout detection circuit and the waveform 17 2012-09-27 ICE3ARxx80CJZ Brownout sensing resistor RBO1 can be fixed to 9MΩ and RBO2 can be calculated as below. where VBO_L_max VBO_E_max = 1.36V (leave/reset brownout): brownout reference voltage for comparator C1a = 1.09V (enter/detect brownout): brownout reference voltage for comparator C1b VBO_L_DC : input DC voltage to leave/reset brownout (high point) VBO_E_DC : input DC voltage to enter/detect brownout (low point) RBO1 and RBO2 : Brownout resistors divider from input voltage to BRL pin For example, if brownout leave/reset voltage is 85Vac and assuming there is no ripple voltage at hold up capacitor, C14 (refer to Figure.3). By using the above brownout resistors RBO1=9MΩ & RBO2=105kΩ, brownout enter/detect voltage can be calculated as below. So, enter/detect brownout AC voltage is Note: minimum current at RBO1 should be higher than 10 times of BRL pin leakage current (0.5µA) to avoid malfunction. For example, RBO1 =9MΩ, RBO2 =105kΩ, minimum current through RBO1 which is 20 times higher than leakage current at BRL pin. 93Vdc 115Vdc 115Vdc 90Vdc VC14 VC14 Vcs Vcs Vcc BRL Vcc BRL BRL VBRL VBRL BRL BRL Brownout reset: VC14= 115Vdc (82Vac), VBRL=1.26V Brownout detect: VC14= 93Vdc (66Vac), VBRL=1V Brownout mode with max. load Figure 19 Application Note BRL Brownout reset: Vbulk= 115Vdc (82Vac),VBRL=1.26V Brownout detect: Vbulk= 90Vdc (65Vac), VBRL=1V Brownout mode with no load Brownout mode waveform 18 2012-09-27 ICE3ARxx80CJZ If the brownout feature is not needed, it needs to tie the BRL pin to the Vcc pin through a current limiting resistor (R114), 5MΩ~10ΜΩ. The BRL pin cannot be in floating condition. Alternatively a lower cost brownout circuit connection can be achieved as shown in Figure 20. The C1 and C2 capacitors can be a low voltage capacitor as the resistor divider R1, R2 and R3 are in high impedance. However, since the IC brownout window is narrow, it needs to have another RC filter R4, R5 and C2 to reduce the ripple voltage. A design example for this design is as below. Leave brownout voltage = 70Vac, Enter brownout voltage = 55~60Vac R1=3.9MΩ, R2=1.5MΩ, R3=3MΩ, R4=215kΩ, R5=140kΩ, C1=47nF, C2=1nF R1 R2 R3 R4 BRL L R5 C1 N Figure 20 C2 Alternative brownout circuit connection 6.6.5 User defined protection by latch enable (BRL) pin Figure 21 D N G signal enable latch External ICE3ARXX80CJZ Although there are lots of pre-defined Auto Restart Protection is implemented in the IC, customer still can have some tailor-made protection for the application needs by pulling down the BRL pin to lower 0.4V for 210µs. When BRL pin is lower than 0.4V, the gate drive switching will be stopped and IC will enter to latch mode. User defined external latch enable circuit A simply output OVP circuit is shown in Figure 22. The output voltage is sensed by the auxiliary winding. When the pre-set OVP voltage is reached, the zener diode Z1 is triggered and the transistor T1 is on. The BRL pin is pulled down and latched off. D1 Auxiliary winding Figure 22 Application Note Z1 R1 R2 C1 T1 BRL R3 C2 Output OVP circuit by sensing the auxiliary winding 19 2012-09-27 ICE3ARxx80CJZ 6.6.6 Fast AC reset During the normal operation, the ICE3ARxx80CJZ can be latched by pulling down the BRL voltage as explained in section 6.6.5 and latch mode can be reset by the AC recycle. For the ordinary AC recycle, switch of the main AC power until the Vcc voltage below 8V and it will take quite a long time depending on the size of Vcc capacitor. To avoid this longer time to reset latch, “Fast AC reset” feature is implemented in the ICE3ARxx80CJZ, by sensing the BRL voltage rise time from 0.4V to 1V for at least 450µs after IC enter latch mode. Figure 23 Latch and fast AC reset Case a : not latched (solid line); the timing below 0.4V is 150s and is less than 210s. Case b : latched (dashed line); the timing below 0.4V is 450s which is larger than 210s. No latch reset as the rise time from 0.4V to 1V is 300s which is less than the 450s. Case c : latched and reset (dotted line); the timing below 0.4V is 710s which is larger than 210s. But the rise time from 0.4V to 1V is 560s which is larger than the latch reset blanking time of 450s. Figure 24 Latch and fast AC reset example Pre-caution: During the lightning surge test if the lightning surge noise is too much and strong, the latch protection voltage at BRL pin may mis-triggered and the system may enter into protection mode. To avoid this risk, R17 and C19 (refer to figure 3) can be selected to reduce the risk. In general, the design can be as below. The bigger the C19 capacitance, the longer the VBRL dip and it may enter to protection mode (recommended value for C19=100pF~1nF). The smaller the R17 resistance, the bigger the negative spike and it may malfunction the controller. On the other hand, the R17 resistance cannot be too large as it may couple the noise easily and the brownout/latch function may not work properly in normal operation (recommended value for R17=0Ω~2kΩ). Application Note 20 2012-09-27 ICE3ARxx80CJZ 7 Input power curve The purpose of the input power curve is to simplify the selection of the CoolSET ® device. The curve is a function of ambient temperature to the input power of the system in which the input filter loss, bridge rectifier loss and the MOSFET power loss are considered. The only information needed is the required output power, the input voltage range, the operating ambient temperature and the efficiency of the system. The required input power can then be calculated as equation (11). Pin Po (11) where Pin : input power, Po : output power, η : efficiency It then simply looks up the closed input power at the required ambient temperature from the input power curve. The input power curves for the CoolSET-F3R80CCM (DIP-7) family are listed below. ICE3AR2280CJZ : Vin=85Vac~265Vac Figure 25 ICE3AR2280CJZ : Vin=230Vac±15% Input power curve for ICE3AR2280CJZ ICE3AR10080CJZ : Vin=85Vac~265Vac Figure 26 Application Note ICE3AR10080CJZ : Vin=230Vac±15% Input power curve for ICE3AR10080CJZ 21 2012-09-27 ICE3ARxx80CJZ The major assumption for the calculation is listed below. 1. Reflection voltage from secondary side to primary side is 150V. 2. The assumed maximum power for the device is when the junction temperature of the integrated ® CoolMOS reaches 125°C. (With some margins to reach the over temperature protection of the device : 130°C). The maximum Rdson of the device at 125°C is taken for calculation. 3. There is no copper area as heat sink and the Rthja=96K/W (DIP-7) 4. Saturation current (Id_max @ 125°C) of the MOSFET is considered which is showed in below table. 5. The typical resistance of the EMI filter is listed in the below table. 6. The voltage drop for the bridge rectifier is assumed to be 1V. Rdson_125°C (Ω) Id_max @125°C (A) REMI_filter (Ω) VF_bridge (V) ICE3AR2280CJZ 5.80 2.87 2*2 2*1 ICE3AR10080CJZ 24.6 0.675 2*3 2*1 8 Layout Recommendation In order to get the optimized ruggedness of the IC to the transient surge events like ESD and lightning Surge test, the grounding of the PCB layout must be connected carefully. From the circuit diagram in Figure 3, it indicates that the grounding for the controller can be split into several groups; signal ground, Vcc ground, Current sense resistor ground and EMI return ground. All the split grounds should be “star” connected to the bulk capacitor ground directly. The split grounds are described as below. Signal ground includes all small signal grounds connecting to the controller GND pin such as filter capacitor ground, C17, C18, C19, C111, C115 and opto-coupler ground.. Vcc ground includes the Vcc capacitor ground, C16 and the auxiliary winding ground, pin 2 of the power transformer. Current Sense resistor ground includes current sense resistor R14 and R15. EMI return ground includes Y capacitor, C12. Product portfolio of CoolSET® F3R80CCM (DIP-7) brownout & CCM version 9 1 1 2 Device Package VDS Frequency / kHz Rdson /Ω 230Vac±15% 85-265Vax±15% ICE3AR10080CJZ PG-DIP-7 800V 100 10.0 22W 15W ICE3AR2280CJZ PG-DIP-7 800V 100 2.26 43W 28W 2 Typ @ 25°C 2 Calculated maximum input power rating at T a=50°C, Tj=125°C and without copper area as heat sink. Refer to the data sheet for input power curve of other Ta Application Note 22 2012-09-27 ICE3ARxx80CJZ 10 Useful formula for the SMPS design Transformer ( CCM flyback) , , Input data Turn ratio Duty maximum Primary Inductance Primary peak current Maximum DC voltage for CCM full load Primary rms current Primary turns Secondary turns Auxiliary turns Application Note 23 2012-09-27 ICE3ARxx80CJZ ICE3ARxx80CJZ other components Current sense resistor Soft start time Vcc capacitor Startup time Enter burst mode power Output ripple during burst mode Leave burst mode power Built-in blanking time for over load protection Brownout resistor , RBO1 & RBO2 Note: minimum current at RBO1 should be higher than 10 times of BRL pin leakage current (0.5µA) to avoid malfunction Input DC voltage to enter brownout mode Application Note 24 2012-09-27 ICE3ARxx80CJZ 11 Design calculation example Application Note 25 2012-09-27 ICE3ARxx80CJZ Application Note 26 2012-09-27 ICE3ARxx80CJZ Application Note 27 2012-09-27 ICE3ARxx80CJZ 12 References [1] Infineon Technologies, Datasheet “CoolSET®-F3R80 ICE3AR2280CJZ Off-Line SMPS Current Mode Controller with Integrated 800V CoolMOS® and Startup Cell (Brownout & CCM) in DIP-7” [2] Infineon Technologies, Datasheet “CoolSET®-F3R80 ICE3AR10080CJZ Off-Line SMPS Current Mode ® Controller with Integrated 800V CoolMOS and Startup Cell (Brownout & CCM) in DIP-7” [3] Kyaw Zin Min, Kok Siu Kam Eric, Infineon Technologies, Application Note “AN-EVAL3AR2280CJZ, 20W 5V SMPS Evaluation Board with CoolSET®-F3R80CCM ICE3AR2280CJZ” [4] Kyaw Zin Min, Kok Siu Kam Eric, Infineon Technologies, Application Note “AN-EVALICE3AR10080CJZ, ® 10W 5V SMPS Evaluation Board with CoolSET -F3R80CCM ICE3AR10080CJZ” Application Note 28 2012-09-27 ICE3ARxx80CJZ 13 Appendix 1 – reference circuit to solve output OVP by external voltage short If there is a high external output voltage shorted to the 5V output, the circuit in Figure 3 cannot react for the OVP protection. Additional circuit is needed to achieve the protection. 1. D22 and C28 : additional power to sustain the Vo OVP ckt as the switching will stop. 2. Q12, Q13, R117, R118, R119 and C113 : additional circuit to open the control loop and leave the active burst mode to normal load if the OVP happened at light load (burst mode). Application Note 29 2012-09-27