MEDICAL PM110 Series 7 2 - 1 1 0 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T FEATURES • Low safety ground leakage current • Wide input range 85 to 264Vac • Input surge current protection • Overvoltage protection • Overcurrent protection • Open PCB construction • 100% burn-in at full rated load SPECIFICATIONS INPUT OPERATING Input voltage 85–264Vac wide input MTBF 400,000 hrs @ 25°C Frequency 47Hz–67Hz Efficiency 66%–75% Input current 3.2A (rms) for 115Vac. 1.8A (rms) for 230Vac. 90µA max. @ 115Vac. 60Hz. 150µA max. @ 230Vac. 50Hz. Input – Output: 4000VAC Input – Ground: 1500VAC Output – Ground: 500VAC Leakage current Isolation Inrush current 15A @ 115V, 30A @ 230V OUTPUT Output voltage ENVIRONMENTAL Operating temperature 0°C to 70°C Derating Derate to 50% at 70°C Storage temperature -40°C to 85°C Relative humidity 5%–95% non-condensing STANDARDS AND APPROVALS Safety UL 60601-1, CSA C22.2 No. 601.1, TÜV EN 60601-1, UL 60950-1, CSA C22.2 No. 60950-1, TÜV EN 60950-1 See table Output voltage adjustment V1 ±10% Output current See table C-Tick AS/NZS CISPR11 Group1, Class A Ripple & noise 1% peak to peak EMC standards Line regulation ±0.5% maximum at full load. Load regulation Transient response See table Max. deviation 4% recovering to 1% within 500µs after 25% load charge Provided on V1 only. Set at 110%–132% of nominal All outputs protected for short circuit conditions IEC60601-1-2, EN55011 / EN55022 and FCC, VCCI: Class B conducted . class B radiated EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11 Overvoltage protection Overcurrent protection 402 Temperature coefficient All outputs ±0.04% per °C Holdup time Typically 12mS at 110VAC PFD signal Power fail detection signal. TTL logic low upon loss of input power. Immunity standards MECHANICAL Dimensions 177.8x108x47mm Weight 640 grams. Doc. No. PBC9 Rev.C 28-4-11 PM110 Series SELECTION TABLE OUTPUT #1 (2) MODEL (1) PM110-10-1A PM110-10A PM110-12A PM110-13A PM110-14A PM110-16A PM110-23A PM110-31A PM110-32A PM110-40A PM110-41A PM110-42A PM110-45A PM110-45-1A PM110-45-2A PM110-46A V1 3.3 V 5.0 V 12 V 15 V 24 V 30 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V +5.1 V OUTPUT #2 IMIN. IMAX TOL. . 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 2A 0A 0A 22 A 22 A 9.0 A 7.5 A 4.5 A 3.6 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A 10 A ±3% ±3% ±2% ±2% ±2% ±3% ±3% ±3% ±3% ±3% ±3% ±3% ±3% ±3% ±3% ±3% V2 +12 V +12 V +15 V +12 V +15 V +12 V +12 V +12 V +24 V +15 V OUTPUT #3 IPEAK( TOL. IMIN. IMAX 4) . 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) 5A 5A 4A 5A 4A 5A 5A 5A 3A 4A V3 OUTPUT #4 IMIN. IMAX TOL. . (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) 9.0 A ±3% (NA) 9.0 A ±3% -12 V 0 A 1 A 7.5 A ±3% -15 V 0 A 1A 9.0 A ±3% -12 V 0 A 1A 7.5 A ±3% -15 V 0 A 1A 9.0 A ±3% -12 V 0 A 1A 9.0 A ±3% -12 V 0 A 1A 9.0 A ±3% -12 V 0 A 1A 5.0 A ±3% -12 V 0 A 1A 7.5 A ±3% -15 V 0 A 1A ±4% +4% +4% +4% +4% +4% +4% +4% +4% V4 -5 V +24 V +12 V +24 V +24 V +12 V -5 V IMIN. IMAX TOL. . (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (NA) 0A 1A 0A 1A 0A 1A 0A 1A 1.5 A 3 A 0A 1A 0A 1A ±4% +4% +4% +4% +4% +4% +4% MAX. OUTPUT POWER(3) 60 W / 72 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W 80 W / 110 W MEDICAL 7 2 - 1 1 0 W AT T S - A C / D C S I N G L E & M U LT I P L E O U T P U T NOTES: 1. Safety agency approvals are for the above listed models in PCB format. To order a model with a metallic L-bracket or box, change suffix “A” to “B” for L-bracket format, to “C” for enclosed form with cover, e.g. PM110-14C. (mechanical details shown in Annex H) 2. The output #1 of model PM110-45-1A needs a minimum current of 2A to support the other outputs at their maximum rated load. 3. 110 watts maximum at 25 CFM forced air cooling or 80 watts maximum at convection cooling, except model PM110-10-1A which is rated at 60 watts maximum at convection cooling or 72 watts maximum at 25 CFM forced air cooling. 4. Peak output current with 10% maximum duty cycle for less than 60 seconds. Total peak power must not exceed 130 watts. 5. All models may be operated at no-load. At no-load, output voltage tolerance increases to ±10%. 6. Ripple and noise is maximum peak-to-peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 µF tantalum capacitor in parallel with a 0.1 µF ceramic capacitor across the output. MECHANICAL SPECIFICATIONS OUTPUT POWER DERATING CURVE NOTES: 1. 2. 3. 4. 5. 6. Dimensions shown in inches [mm] Tolerance 0.02 [0.5] maximum Connector P1: Molex header 09-65-2058 or equivalent, mating with Molex housing 09-50-1051 or equivalent. Connector P2 mates with Molex 09-50-3131 or equivalent. The copper pad of the mounting hole near P1 is for system grounding through a metallic stand-off to system chassis. Weight：640 grams (1.408 lbs.) PIN CHART MODEL/PIN 1,2,3 4,5 6,7 8,9 10 11 12 13 +V1 V1 Return V1 Return +V1 P.F.D. N.C. Key N.C. V1 Common Return Common Return Common Return Common Return V2 P.F.D. N.C. Key N.C. V2 P.F.D. V33 Key N.C. Common Return Common Return V2 P.F.D. V3 Key V4 PM110-10-1A PM110-10A PM110-12A PM110-23A PM110-13A PM110-14A PM110-16A PM110-31A PM110-32A V1 PM110-40A PM110-41A PM110-42A PM110-45A PM110-45-1A PM110-45-2A PM110-46A V1 Doc. No. PBC9 Rev.C 28-4-11 Powering Progress – www.powerbox.com.au 403