Single, Dual, Quad General Purpose Micropower, RRIO Operational Amplifier ISL28113, ISL28213, ISL28413 Features The ISL28113, ISL28213, and ISL28413 are single, dual, and quad channel general purpose micropower, rail-to-rail input and output operational amplifiers with supply voltage range of 1.8V to 5.5V. Key features are a low supply current of 130µA maximum per channel at room temperature, a low bias current and a wide input voltage range, which enables the ISL28x13 devices to be excellent general purpose op-amps for a wide range of applications. • Low Current Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . 130µA The ISL28113 is available in the SC70-5 and SOT23-5 packages, the ISL28213 is in the MSOP8, SOIC8, SOT23-8 packages, and the ISL28413 is in the TSSOP14, SOIC14 packages. All devices operate over the extended temperature range of -40°C to +125°C. • Wide Supply Range . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 5.5V • Gain Bandwidth Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2MHz • Input Bias Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20pA, Max. • Operating Temperature Range. . . . . . . . . . . . .-40°C to +125°C • Packages - ISL28113 (Single) . . . . . . . . . . . . . . . . . . . . . SC70-5, SOT23-5 - ISL28213 (Dual). . . . . . . . . . . . . . . . MSOP8, SOIC8, SOT23-8 - ISL28413 (Quad) . . . . . . . . . . . . . . . . . . . . . SOIC14, TSSOP14 Applications • Power Supply Control/Regulation Related Literature • Process Control • See AN1519 for “ISL28213/14SOICEVAL2Z Evaluation Board User’s Guide” • Signal Gain/Buffers • See AN1520 for “ISL28113/14SOT23EVAL1Z Evaluation Board User’s Guide” • Current Shunt Sensing • See AN1542 for “ISL28213/14MSOPEVAL2Z Evaluation Board User’s Guide” • Active Filters • Trans-impedance Amps RF 100kΩ LOAD RINRSENSE IN- 10kΩ RIN+ IN+ +5V - VOUT V+ ISL28x13 V- + 10kΩ GAIN = 10 RREF+ 100kΩ VREF SINGLE-SUPPLY, LOW-SIDE CURRENT SENSE AMPLIFIER FIGURE 1. TYPICAL APPLICATION June 9, 2011 FN6728.5 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2009-2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL28113, ISL28213, ISL28413 Ordering Information PART NUMBER (Notes 2, 3) PART MARKING PACKAGE (Pb-Free) PKG. DWG. # ISL28113FEZ-T7 (Note 1) BJA 5 Ld SC-70 P5.049 ISL28113FEZ-T7A (Note 1) BJA 5 Ld SC-70 P5.049 ISL28113FHZ-T7 (Note 1) BCYA 5 Ld SOT-23 P5.064A ISL28113FHZ-T7A (Note 1) BCYA 5 Ld SOT-23 P5.064A ISL28213FUZ 8213Z 8 Ld MSOP M8.118A ISL28213FUZ-T7 (Note 1) 8213Z 8 Ld MSOP M8.118A ISL28213FBZ 28213 FBZ 8 Ld SOIC M8.15E ISL28213FBZ-T7 (Note 1) 28213 FBZ 8 Ld SOIC M8.15E ISL28213FBZ-T13 (Note 1) 28213 FBZ 8 Ld SOIC M8.15E Coming Soon ISL28213FHZ-T7 (Note 1) TBD 8 Ld SOT-23 P8.064 Coming Soon ISL28213FHZ-T7A (Note 1) TBD 8 Ld SOT-23 P8.064 ISL28413FVZ 28413 FVZ 14 Ld TSSOP MDP0044 ISL28413FVZ-T7 (Note 1) 28413 FVZ 14 Ld TSSOP MDP0044 ISL28413FVZ-T13 (Note 1) 28413 FVZ 14 Ld TSSOP MDP0044 ISL28413FBZ 28413 FBZ 14 Ld SOIC MDP0027 ISL28413FBZ-T7 (Note 1) 28413 FBZ 14 Ld SOIC MDP0027 ISL28413FBZ-T13 (Note 1) 28413 FBZ 14 Ld SOIC MDP0027 ISL28113SOT23EVAL1Z Evaluation Board ISL28213MSOPEVAL2Z Evaluation Board ISL28213SOICEVAL2Z Evaluation Board Coming Soon ISL28413TSSOPEVAL1Z Evaluation Board NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL28113, ISL28213, ISL28413. For more information on MSL please see Techbrief TB363. Pin Configurations ISL28113 (5 LD SC-70) TOP VIEW IN+ 1 VS- 2 IN- 3 5 4 ISL28113 (5 LD SOT-23) TOP VIEW VS+ OUT 2 OUT 1 VS- 2 IN+ 3 5 4 ISL28213 (8 LD MSOP, 8 LD SOIC, 8 LD SOT-23) TOP VIEW VS+ IN- OUT_A 1 8 VS+ IN-_A 2 7 OUT_B IN+_A 3 6 IN-_B VS- 4 5 IN+_B FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Pin Configurations (Continued) ISL28413 (14 LD TSSOP, 14 LD SOIC) TOP VIEW 14 OUT_D OUT_A 1 IN-_A 2 13 IN-_D IN+_A 3 12 IN+_D 11 VS- VS+ 4 IN+_B 5 10 IN+_C IN-_B 6 9 IN-_C 8 OUT_C OUT_B 7 Pin Descriptions PIN NUMBER PIN NAME OUT OUT_A OUT_B OUT_C OUT_D 5 LD SC-70 5 LD SOT-23 4 1 8 LD MSOP, 8 LD SOIC, 8 LD SOT-23 14 LD TSSOP, 14 LD SOIC DESCRIPTION Output 1 7 V+ 1 7 8 14 OUT VCIRCUIT 1 VS- 2 2 4 11 Negative supply voltage V+ CAPACITIVELY TRIGGERED ESD CLAMP VCIRCUIT 2 IN+ IN+_A IN+_B IN+_C IN+_D 1 ININ-_A IN-_B IN-_C IN-_D 3 VS+ 5 Positive Input 3 3 5 3 5 10 12 V+ IN- IN+ Negative Input 4 2 6 5 8 3 2 6 9 13 4 VCIRCUIT 3 Positive supply voltage See “CIRCUIT 2” FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V Supply Turn-on Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . .V- - 0.5V to V+ + 0.5V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V- - 0.5V to V+ + 0.5V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V Machine Model ISL28113, ISL28213 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350V ISL28413. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000V Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 5 Ld SC-70 (Notes 4, 5) . . . . . . . . . . . . . . . . 250 N/A 5 Ld SOT-23 (Notes 4, 5) . . . . . . . . . . . . . . . 225 N/A 8 Ld MSOP (Notes 4, 5) . . . . . . . . . . . . . . . . 180 100 8 Ld SOIC Package (Notes 4, 5) . . . . . . . . . 126 90 8 Ld SOT-23 (Notes 4, TBD) . . . . . . . . . . . . 240 TBD 14 Ld TSSOP Package (Notes 4, 5) . . . . . . 120 40 14 Ld SOIC Package (Notes 4, 5). . . . . . . . 90 50 Ambient Operating Temperature Range . . . . . . . . . . . . . . -40°C to +125°C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. For θJC, the “case temp” location is the top of the package. Electrical Specifications VS+ = 5V, VS- = 0V, RL = Open, VCM = VS/2, TA = +25°C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C, unless otherwise specified. PARAMETER DESCRIPTION CONDITIONS MIN (Note 6) TYP MAX (Note 6) UNIT -5 0.5 5 mV 6 mV 2 10 µV/°C 1 30 pA 3 20 pA 100 pA 20 pA -50 50 pA - 0.1V +5.1V V DC SPECIFICATIONS VOS Input Offset Voltage -6 TCVOS Input Offset Voltage Temperature Coefficient IOS Input Offset Current IB Input Bias Current -40°C to +125°C ISL28113 -20 -100 ISL28213, ISL28413 Common Mode Input Voltage Range -20 3 ZIN Input Impedance 1012 Ω CIN Input Capacitance 1 pF CMRR Common Mode Rejection Ratio VCM = -0.1V to 5.1V 72 dB -40°C to +125°C 70 dB VS = 1.8V to 5.5V 71 dB -40°C to +125°C 70 dB 4.993 V PSRR VOH Power Supply Rejection Ratio Output Voltage Swing, High RL = 10kΩ 4.985 4.98 VOL V+ Output Voltage Swing, Low Supply Voltage 4 RL = 10kΩ V 13 1.8 15 mV 20 mV 5.5 V FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Electrical Specifications VS+ = 5V, VS- = 0V, RL = Open, VCM = VS/2, TA = +25°C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +125°C, unless otherwise specified. (Continued) PARAMETER IS DESCRIPTION Supply Current per Amplifier CONDITIONS RL = OPEN MIN (Note 6) TYP MAX (Note 6) UNIT 90 130 µA 170 µA ISC+ Output Source Short Circuit Current RL = 10Ω to V- -22 mA ISC- Output Sink Short Circuit Current RL = 10Ω to V+ 16 mA GBWP Gain Bandwidth Product VS = ±2.5V AV = 100, RF = 100kΩ, RG = 1kΩ, RL = 10kΩ to VCM 2 MHz eN VP-P Peak-to-Peak Input Noise Voltage VS = ±2.5V f = 0.1Hz to 10Hz 14 µVP-P eN Input Noise Voltage Density VS = ±2.5V f = 1kHz 55 nV/√(Hz) iN Input Noise Current Density VS = ±2.5V f = 1kHz 5 fA/√(Hz) Cin Differential Input Capacitance VS = ±2.5V f = 1MHz 1.0 pF 1.3 pF 1 V/µs 100 ns 115 ns 7.5 µs AC SPECIFICATIONS Common Mode Input Capacitance TRANSIENT RESPONSE SR Slew Rate 20% to 80% VOUT VOUT = 0.5V to 4.5V tr, tf, Small Signal Rise Time, tr 10% to 90% VS = ±2.5V AV = +1, VOUT = 0.05VP-P, RF = 0Ω, RL = 10kΩ, CL = 15pF Fall Time, tf 10% to 90% ts Settling Time to 0.1%, 4VP-P Step VS = ±2.5V AV = +1, RF = 0Ω, RL = 10kΩ, CL = 1.2pF NOTE: 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 5 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Typical Performance Curves VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified. 50 10,000 40 10 0 -10 -20 -30 SIMULATION -50 -40 -20 0 20 40 60 80 100 120 140 1000 100 10 1 10 100 TEMPERATURE (°C) 10k 100k FIGURE 3. INPUT NOISE VOLTAGE SPECTRAL DENSITY FIGURE 2. INPUT BIAS CURRENT vs TEMPERATURE 20 120 20 100 0 100 0 -20 80 GAIN 60 -40 40 -60 20 -80 0 -100 -20 V+ = ±0.9V RL = 100k -40 CL = 10pF -60 SIMULATION -80 0.1 1 10 -120 PHASE -140 -160 100 1k 10k 100k FREQUENCY (Hz) 1M -180 10M 100M 80 -20 GAIN 60 -60 20 -80 0 -100 -20 V+ = ±2.5V RL = 100k -40 CL = 10pF -60 SIMULATION -80 0.1 80 70 70 60 60 50 50 30 20 10 SIMULATION 0 0.01 0.1 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) 10M 100M FIGURE 6. CMRR vs FREQUENCY, VS = ±2.5 6 1 10 -120 PHASE -140 -160 100 1k 10k 100k FREQUENCY (Hz) 1M -180 10M 100M FIGURE 5. OPEN-LOOP GAIN, PHASE vs FREQUENCY, RL = 100kΩ, CL = 10pF, VS = ±2.5V 80 40 -40 40 PSRR (dB ) CMRR (dB) FIGURE 4. OPEN-LOOP GAIN, PHASE vs FREQUENCY, RL = 100kΩ, CL = 10pF, VS = ±0.9V OPEN LOOP GAIN (dB) 120 PHASE (°) OPEN LOOP GAIN (dB) 1k FREQUENCY (Hz) PHASE (°) IBIAS (pA) 20 -40 V+ = ±2.5V AV = 1 INPUT NOISE VOLTAGE (nV/√Hz) 30 PSRR- VS = ±2.5V PSRR- VS = ±0.9V PSRR+ VS = ±0.9V 40 30 PSRR+ VS = ±2.5V RL = INF 20 C = 4pF L 10 AV = +1 VCM = 100mVP-P 0 100 1k 10k 100k FREQUENCY (Hz) 1M 10M FIGURE 7. PSRR vs FREQUENCY, VS = ±0.9V, ±2.5V FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Typical Performance Curves 70 GAIN (dB) V+ = ±2.5V CL = 4pF RL = 10k VOUT = 50mVP-P AV = 100 30 20 AV = 10 Rg = 10k, Rf = 100k 10 0 0 Rg = 1k, Rf = 100k 50 40 1 Rg = 100, Rf = 100k AV = 1000 NORMALIZED GAIN (dB) 60 VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified. (Continued) AV = 1 1k 100 -2 -3 VOUT = 10mVP-P -4 VOUT = 50mVP-P VOUT = 100mVP-P -5 VS = ±2.5V -6 10k 100k 1M FREQUENCY (Hz) 10M -7 -9 100 100M 1 6 0 5 RL = 49.9k -2 RL = 10k -3 -4 RL = 4.99k -5 -6 -7 -8 V+ = ±2.5V RL = 1k CL = 4pF AV = +1 VOUT = 50mVP-P -9 100 1k RL = 499 RL = 100 10k 100k FREQUENCY (Hz) 1M 1k 10k 100k FREQUENCY (Hz) 1M 10M 10M CL = 1004pF 3 CL = 474pF 2 CL = 224pF 1 0 CL = 104pF -1 VS = ±2.5V RL = 10k -2 AV = +1 -3 VOUT = 50mVP-P -4 10k 1k CL = 26pF CL = 4pF 100k FREQUENCY (Hz) 1M 10M FIGURE 11. GAIN vs FREQUENCY vs CL 1 140 0 120 -1 CROSS-TALK (dB) NORMALIZED GAIN (dB) VOUT = 1VP-P 4 FIGURE 10. GAIN vs FREQUENCY vs RL -2 -3 -4 -5 VS = ±2.5V -6 CL = 4pF RL = 10k -7 AV = +1 -8 VOUT = 50mVP-P VS = ±1.75V -9 10k VOUT = 500mVP-P FIGURE 9. FREQUENCY RESPONSE vs VOUT NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) FIGURE 8. FREQUENCY RESPONSE vs CLOSED LOOP GAIN -1 VOUT = 200mVP-P CL = 4pF AV = +1 RL = 10k -8 Rg = OPEN, Rf = 0 -10 10 -1 VS = ±1.25V 10M FIGURE 12. GAIN vs FREQUENCY vs SUPPLY VOLTAGE 7 80 60 40 20 VS = ±0.9V 100k 1M FREQUENCY (Hz) 100 0 10 VS = ±2.5V RL-DRIVER = INF RL-RECEIVER = 10k CL = 4pF AV = +1 VSOURCE = 1VP-P 100 1k 10k 100k FREQUENCY (Hz) 1M 10M FIGURE 13. CROSSTALK, VS = ±2.5V FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 VS = ±2.5V, VCM = 0V, RL = Open, unless otherwise specified. (Continued) 30 3 20 2 LARGE SIGNAL (V) 10 VS = ±2.5V RL = 10k CL = 15pF AV = +1 VOUT = 50mVP-P 0 -10 -20 -30 1 VS = ±0.9V 0 RL = 10k CL = 15pF AV = +1 VOUT = RAIL -1 -2 0 200 400 600 -3 800 1000 1200 1400 1600 1800 2000 TIME (ns) 0.5 0 RL = INF CL = 15pF AV =10 Rf = 9.09k, Rg = 1k -0.1 -0.2 -0.3 0.5 -0.5 0.4 -1.5 OUTPUT @ VS=±0.9V OUTPUT @ VS = ±2.5V -0.4 0 -1.0 -0.5 2 4 6 8 10 12 TIME (ms) 14 16 18 0.6 INPUT (V) INPUT OUTPUT (V) 0.1 0 20 FIGURE 15. LARGE SIGNAL TRANSIENT RESPONSE vs RL VS = ±0.9V, ±2.5V FIGURE 14. SMALL SIGNAL TRANSIENT RESPONSE, VS = ±2.5V INPUT (V) VS = ±2.5V 3.0 OUTPUT @ VS = ±2.5V RL = INF CL = 15pF AV =10 Rf = 9.09k, Rg = 1k 0.2 0.1 -2.5 0 2.0 OUTPUT @ VS=±0.9V 0.3 -2.0 2.5 1.5 1.0 OUTPUT (V) SMALL SIGNAL (mV) Typical Performance Curves 0.5 0 INPUT -0.6 0 1 2 3 4 5 6 TIME (ms) 7 8 9 -3.0 10 -0.1 FIGURE 16. NEGATIVE OUTPUT OVERLOAD RESPONSE TIME, VS = ±0.9V, ±2.5V 0 1 2 3 4 5 6 TIME (ms) 7 8 9 -0.5 10 FIGURE 17. POSITIVE OUTPUT OVERLOAD RESPONSE TIME, VS = ±0.9V, ±2.5V 90 O T O T VE R O 20 SH 30 O O 40 SH 50 + 60 O VE R OVERSHOOT (%) VS = ±2.5V 80 RL = 10k AV = 1 70 V OUT = 50mVP-P 10 0 10 100 1k CAPACITANCE (pF) 10k FIGURE 18. % OVERSHOOT vs LOAD CAPACITANCE, VS = ±2.5V 8 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Applications Information Power Dissipation Functional Description It is possible to exceed the +125°C maximum junction temperatures under certain load, power supply conditions and ambient temperature conditions. It is therefore important to calculate the maximum junction temperature (TJMAX) for all applications to determine if power supply voltages, load conditions, or package type need to be modified to remain in the safe operating area. These parameters are related using Equation 1: The ISL28113, ISL28213 and ISL28413 are single, dual and quad, CMOS rail-to-rail input, output (RRIO) micropower operational amplifiers. They are designed to operate from single supply (1.8V to 5.5V) or dual supply (±0.9V to ±2.75V). The parts have an input common mode range that extends 100mV above and below the power supply voltage rails. The output stage can swing to within 15mV of the supply rails with a 10kΩ load. Input ESD Diode Protection where: All input terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails (see “Pin Descriptions Circuit 1” on page 3). For applications where the input voltage may exceed either power supply voltage by 0.5V or more, an external series resistor must be used to ensure the input currents never exceed 20mA (see Figure 19). V+ VIN- RIN- - RIN+ + (EQ. 1) T JMAX = T MAX + θ JA xPD MAXTOTAL • PDMAXTOTAL is the sum of the maximum power dissipation of each amplifier in the package (PDMAX) • PDMAX for each amplifier can be calculated using Equation 2: V OUTMAX PD MAX = V S × I qMAX + ( V S - V OUTMAX ) × -----------------------R (EQ. 2) L where: • TMAX = Maximum ambient temperature RF • θJA = Thermal resistance of the package • PDMAX = Maximum power dissipation of 1 amplifier • VS = Total supply voltage RL RG V- FIGURE 19. INPUT ESD DIODE CURRENT LIMITING Output Phase Reversal Output phase reversal is a change of polarity in the amplifier transfer function when the input voltage exceeds the supply voltage. The ISL28113, ISL28213 and ISL28413 are immune to output phase reversal, even when the input voltage is 1V beyond the supplies. Unused Channels If the application requires less than all amplifiers one channel, the user must configure the unused channel(s) to prevent it from oscillating. The unused channel(s) will oscillate if the input and output pins are floating. This will result in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to short the output to the inverting input and ground the positive input (as shown in Figure 20). • IqMAX = Maximum quiescent supply current of 1 amplifier • VOUTMAX = Maximum output voltage swing of the application • RL = Load resistance ISL28113, ISL28213 and ISL28413 SPICE Model Figure 21 shows the SPICE model schematic and Figure 22 shows the net list for the SPICE model. The model is a simplified version of the actual device and simulates important AC and DC parameters. AC parameters incorporated into the model are: 1/f and flatband noise, Slew Rate, CMRR, Gain and Phase. The DC parameters are IOS, total supply current and output voltage swing. The model uses typical parameters given in the “Electrical Specifications” Table beginning on page 4. The AVOL is adjusted for 85dB with the dominate pole at 100Hz. The CMRR is set 72dB, f = 35kHz). The input stage models the actual device to present an accurate AC representation. The model is configured for ambient temperature of +25°C. Figures 23 through 32 show the characterization vs simulation results for the Noise Voltage, Closed Loop Gain vs Frequency, Large Signal 5V Step Response, CMRR and Open Loop Gain Phase. + FIGURE 20. PREVENTING OSCILLATIONS IN UNUSED CHANNELS 9 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 LICENSE STATEMENT The information in this SPICE model is protected under the United States copyright laws. Intersil Corporation hereby grants users of this macro-model hereto referred to as “Licensee”, a nonexclusive, nontransferable licence to use this model as long as the Licensee abides by the terms of this agreement. Before using this macro-model, the Licensee should read this license. If the Licensee does not accept these terms, permission to use the model is not granted. The Licensee may not sell, loan, rent, or license the macro-model, in whole, in part, or in modified form, to anyone outside the Licensee’s company. The Licensee may modify the macro-model to suit his/her specific applications, and the Licensee may make copies of this macro-model for use within their company only. This macro-model is provided “AS IS, WHERE IS, AND WITH NO WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED, INCLUDING BUY NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.” In no event will Intersil be liable for special, collateral, incidental, or consequential damages in connection with or arising out of the use of this macro-model. Intersil reserves the right to make changes to the product and the macro-model without prior notice. 10 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 En Vin+ + Voltage Noise Stage + R21 800E3 28 V++ 29 DN D13 + + - 0.00035V En R22 5E11 + CinDiff R23 5E11 - 2 + - R2 R1 1.0004 1.0004 3 Vc Vmid 1 In+ 9 M16 5 M14 R3 10 R4 10 11 R7 1 M15 Cin1 Cin2 1.26pF 1.26pF + - 100 25E-12 - V-- 4 15 DX D2 5 RA2 1 G2A +1E-6V IOS DX D1 R9 14 13 I1 5E-3 R10 1E9 RA1 1 M17 R8 1 7 Vin- G1A R6 10 12 R5 10 6 10 8 4 EOS 1.02pF I2 5E-3 V1 1E-6V Vc + - V9 Vmid V2 V-VCM 1ST Gain Stage Input Stage V++ G1 17 + - 4 5 D3 DX + V3 - 0.61V G3 19 + - R11 1 318.329E3 D5 DX + V5 G5 R13 - 0.604V + - C2 5.0nF 4.5474 R15 1E6 Vmid Vc Vg R12 1 G2 + - 18 - V4 0.61V + - + G4 D4 DX V-- 20 C3 0.604V + V6 5.0nF - R14 D6 DX R16 1E6 G6 E4 + - Vg Vmid 22 + - Vmid V++ 21 16 Vc L1 + - L2 4.5474 318.329E3 V-VCM VCM 1ST Gain Stage (Cont) 2nd Gain Stage Mid Supply Ref Common Mode Gain Stage V++ + - + - E2 D9 DX D10 DX 26 R17 5305.32 ISY 90uA Vg C4 10pF D7 DX 27 24 G11 + V7 + + - 0.08V V8 25 + DX - D8 R18 V-- + E3 V- C3 G8 Supply Isolation Stage 10pF Pole Stage 0.08V G12 5305.32 + VOUT VOUT 23 Vmid V- + R19 50 D11 DY + - + - G9 D12 DY R20 50 + - V+ - G7 V+ G10 Output Stage FIGURE 21. SPICE SCHEMATIC 11 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 * source ISL28113_SPICEmodel * Revision D, LaFontaine February 22, 2010 Improved noise performance * Model for Noise, supply currents, CMRR 72dB f=35kHz, AVOL 85dB f=100Hz * SR = 1.0V/us, GBWP 2MHz, 2nd pole 3MHz Output voltage clamp and short ckt I limit *Copyright 2009 by Intersil Corporation *Refer to data sheet “LICENSE STATEMENT” Use of *this model indicates your acceptance with the *terms and provisions in the License Statement. * Connections: +input * | -input * | | +Vsupply * | | | -Vsupply * | | | | output * | | | | | .subckt ISL28113subckt Vin+ Vin- V+ VVOUT * source ISL28113_DS rev1 * *Voltage Noise E_En VIN+ EN 28 0 1 D_D13 29 28 DN V_V9 29 0 0.45 R_R21 28 0 30 * *Input Stage M_M14 3 1 5 5 NCHANNELMOSFET M_M15 4 VIN- 6 6 NCHANNELMOSFET M_M16 11 VIN- 9 9 PMOSISIL M_M17 12 1 10 10 PMOSISIL I_I1 7 V-- DC 5e-3 I_I2 V++ 8 DC 5e-3 I_IOS VIN- 1 DC 25e-12 G_G1A V++ 14 4 3 1404 G_G2A V-- 14 11 12 1404 V_V1 V++ 2 1e-6 V_V2 13 V-- 1e-6 R_R1 3 2 1.0004 R_R2 4 2 1.0004 R_R3 5 7 10 R_R4 7 6 10 R_R5 9 8 10 R_R6 8 10 10 R_R7 13 11 1 R_R8 13 12 1 R_RA1 14 V++ 1 R_RA2 V-- 14 1 C_CinDif VIN- EN 1.02E-12 C_Cin1 V-- EN 1.26e-12 C_Cin2 V-- VIN- 1.26e-12 * *1st Gain Stage G_G1 V++ 16 15 VMID 334.753e-3 G_G2 V-- 16 15 VMID 334.753e-3 V_V3 17 16 .61 V_V4 16 18 .61 D_D1 15 VMID DX D_D2 VMID 15 DX D_D3 17 V++ DX D_D4 V-- 18 DX R_R9 15 14 100 R_R10 15 VMID 1e9 R_R11 16 V++ 1 R_R12 V-- 16 1 * *2nd Gain Stage G_G3 V++ VG 16 VMID 24.893e-3 G_G4 V-- VG 16 VMID 24.893e-3 V_V5 19 VG .604 V_V6 VG 20 .604 D_D5 19 V++ DX D_D6 V-- 20 DX R_R13 VG V++ 318.329e3 R_R14 V-- VG 318.329e3 C_C2 VG V++ 5E-09 C_C3 V-- VG 5E-09 * *Mid supply Ref E_E4 VMID V-- V++ V-- 0.5 E_E2 V++ 0 V+ 0 1 E_E3 V-- 0 V- 0 1 I_ISY V+ V- DC 90e-6 * *Common Mode Gain Stage with Zero G_G5 V++ VC VCM VMID 0.25118 G_G6 V-- VC VCM VMID 0.25118 E_EOS 1 EN VC VMID 1 R_R15 VC 21 0.001 R_R16 22 VC 0.001 R_R22 EN VCM 5e11 R_R23 VCM VIN- 5e11 L_L1 21 V++ 4.547418E-09 L_L2 22 V-- 4.547418E-09 * *Pole Stage G_G7 V++ 23 VG VMID 0.18849 G_G8 V-- 23 VG VMID 0.18849 R_R17 23 V++ 5.30532 R_R18 V-- 23 5.30532 C_C4 23 V++ 1e-8 C_C5 V-- 23 1e-8 * *Output Stage with Correction Current Sources G_G9 26 V-- VOUT 23 0.02 G_G10 27 V-- 23 VOUT 0.02 G_G11 VOUT V++ V++ 23 0.02 G_G12 V-- VOUT 23 V-- 0.02 V_V7 24 VOUT .08 V_V8 VOUT 25 .08 D_D7 23 24 DX D_D8 25 23 DX D_D9 V++ 26 DX D_D10 V++ 27 DX D_D11 V-- 26 DY D_D12 V-- 27 DY R_R19 VOUT V++ 50 R_R20 V-- VOUT 50 .model pmosisil pmos (kp=16e-3 vto=-0.6) .model NCHANNELMOSFET nmos (kp=3e-3 vto=0.6) .model DN D(KF=6.69e-9 AF=1) .MODEL DX D(IS=1E-12 Rs=0.1) .MODEL DY D(IS=1E-15 BV=50 Rs=1) .ends ISL28113subckt FIGURE 22. SPICE NET LIST 12 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Characterization vs Simulation Results 10,000 V+ = ±2.5V AV = 1 INPUT NOISE VOLTAGE (nV/√Hz) INPUT NOISE VOLTAGE (nV/√Hz) 10,000 1000 100 10 1 10 100 1k FREQUENCY (Hz) 10k 1000 100 10 100k AV = 1000 GAIN (dB) AV = 100 AV = 10 20 40 20 Rg = 10k, Rf = 100k 10 AV = 1 -10 10 0 Rg = OPEN, Rf = 0 10k 100k 1M FREQUENCY (Hz) 1k 100 100M 10M FIGURE 25. CHARACTERIZED CLOSED LOOP GAIN vs FREQUENCY -10 100 VS = ±2.5V LARGE SIGNAL (V) VS = ±0.9V RL = 10k CL = 15pF AV = +1 VOUT = RAIL -1 -2 0 2 4 6 8 10 12 14 16 18 TIME (ms) FIGURE 27. CHARACTERIZED LARGE SIGNAL TRANSIENT RESPONSE vs RL, VS = ±0.9V, ±2.5V 13 10k 100k 1.0M FREQUENCY (Hz) 20 10M 100M VOUT 2 1 0 1.0k (A) AC sims.dat (active) 3 2 LARGE SIGNAL (V) 10 FIGURE 26. SIMULATED CLOSED LOOP GAIN vs FREQUENCY 3 -3 100k 60 V+ = ±2.5V CL = 4pF RL = 10k VOUT = 50mVP-P 30 0 10k Rg = 1k, Rf = 100k 50 40 100 1k FREQUENCY (Hz) (A) AC sims.dat (active) 70 Rg = 100, Rf = 100k GAIN (dB) 60 10 FIGURE 24. SIMULATED INPUT NOISE VOLTAGE FIGURE 23. CHARACTERIZED INPUT NOISE VOLTAGE 70 1 VS = ±2.5V 1 VIN -0 -1 RL = 10k -2 CL = 15pF AV = +10 VOUT = RAIL -3 0 5 10 15 TIME (µs) 20 25 30 FIGURE 28. SIMULATED LARGE SIGNAL TRANSIENT RESPONSE vs RL, VS = ±0.9V, ±2.5V FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 20 100 0 80 -20 GAIN 60 -40 40 -60 20 -80 0 -100 -20 V+ = ±2.5V RL = 100k -40 CL = 10pF -60 SIMULATION -80 0.1 1 10 -120 PHASE -140 -160 100 1k 10k 100k FREQUENCY (Hz) 1M -180 10M 100M FIGURE 29. SIMULATED (DESIGN) OPEN-LOOP GAIN, PHASE vs FREQUENCY OPEN LOOP GAIN (dB)/PHASE (°) 120 PHASE (°) OPEN LOOP GAIN (dB) Characterization vs Simulation Results (Continued) (A) AC sims.dat (active) 200 160 120 80 40 0 0.01 0.1 1.0 10 100 1.0k 10k 100k 1.0M 10M 100M FREQUENCY (Hz) FIGURE 30. SIMULATED (SPICE) OPEN-LOOP GAIN, PHASE vs FREQUENCY (A) AC sims.dat (active) 80 80 70 60 50 CMRR (dB ) CMRR (dB) 60 40 30 20 20 10 0 0.01 40 SIMULATION 0.1 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) FIGURE 31. SIMULATED (DESIGN) CMRR 14 10M 100M 0 0.01 0.1 1.0 10 100 1.0k 10k 100k 1.0M 10M 100M FREQUENCY (Hz) FIGURE 32. SIMULATED (SPICE) CMRR FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to Web to make sure you have the latest Rev. DATE REVISION CHANGE 5/18/11 FN6728.5 - On page 2, Ordering Information table: ISL28113FHZ-T7 & -T7A PKG DWG # changed from MDP0038 (Obsoleted) to P5.064A. Removed ISL28213FHZ and added “Coming Soon” to parts ISL28213FHZ-T7A and ISL28413TSSOPEVAL1Z. - On page 3, Pin Descriptions: Circuit 3 diagram, removed anti-parallel diodes from the IN+ to IN- terminals. - On page 4, Absolute Maximum Ratings: changed Differential Input Voltage from "0.5V" to "V- - 0.5V to V+ + 0.5V". - On page 4, updated CMRR and PSRR parameters in Electrical Specifications table with test condition specifiying -40°C to 125°C typical parameter. - On page 5, updated Note 6 (“over-temp” note) referenced in MIN and MAX column headings of Electrical Specifications table from "Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested." to new standard "Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design." - On page 9, under “Input ESD Diode Protection,” removed “They also contain back to-back diodes across the input terminals.” Changed “For applications where the input differential voltage is expected to exceed 0.5V, an external series resistor...” to “For applications where the input differential voltage may exceed either power supply voltage by 0.5V or more, an external series resistor...”. Removed “Although the amplifier is fully protected, high input slew rates that exceed the amplifier slew rate (±1V/µs) may cause output distortion.” - On page 9, Figure 19: updated circuit schematic by removing back-to-back input protection diodes. - On page 18, replaced Package Outline Drawing MDP0038 (obsolete) with P5.064A. 3/23/10 FN6728.4 Page 1, 2nd paragraph - Added “...SOT23-8 packages...” and changed “SO8” to “SOIC8”. Also global, changed S08 to SOIC8 Pg 2, Ordering Information table: Part # ISL28213FEZ changed to ISL28213FHZ and Part Marking changed to "TBD" -Added Related Literature on page 1, updated ordering information by adding Eval boards. -Added to ordering information part number ISL28213FHZ 8 Ld SOT-23 Package as coming soon. -Replaced Figure 24 Simulated Input Noise Voltage with following changes: Y-axis from “10 to 100” to “10,000 to 10” Removed (A) AC sims.dat (active) from top of graph Curve changed to improve noise performance Made changes to Spice Net List as follows: -Changed Revision from “C” to “D” and added improved noise performance to Revision line. -Changed in Voltage Noise “V_V9 29 0 .00035” to “V_V9 29 0 0.45” “R_R21 28 0 800E3 TC=0,0” to “R_R21 28 0 30” -Removed TC=0 in Input Stage from R_R1 through C_Cin2 -Removed TC=0 in 1st Gain Stage from R_R9 through R_R12 -Removed TC=0 in 2nd Gain Stage from R_R13 through C_C3 -Changed in Common Mode Gain Stage with Zero “G_G5 V++ VC VCM VMID 2.5118E-10” to “G_G5 V++ VC VCM VMID 0.25118” “G_G6 V-- VC VCM VMID 2.5118E-10” to “G_G6 V-- VC VCM VMID 0.25118” Removed TC=0 from R_R16 through R_R23 -Changed in Pole Stage “G_G7 V++ 23 VG VMID 188.49e-6” to ‘G_G7 V++ 23 VG VMID 0.18849” “G_G8 V-- 23 VG VMID 188.49e-6” to “G_G8 V-- 23 VG VMID 0.18849” Removed TC=0 from R_R17 through C_C5 Removed TC=0 in Output Stage with Correction Current Sources from R_R19 and R_R20 Made changes to Spice Schematic Figure 21 as follows: -Input Stage - Modified connection to the EOS (voltage control voltage source) -Added to Thermal Information 8 LD SOT-23 as TBD -Added to pin configuration for the ISL28213 8 Ld SOT-23 12/16/09 FN6728.3 Removed “Coming Soon” from MSOP package options in the “Ordering Information” on page 2. Updated the Theta JA for the MSOP package option from 170°C/W to 180°C/W on page 4. 11/17/09 FN6728.2 Removed “Coming Soon” from SC70 and SOT-23 package options in the “Ordering Information” on page 2. 11/12/09 FN6728.1 Changed theta Ja to 250 from 300. Added license statement (page 10) and reference in spice model (page 12). 10/26/09 FN6728.0 Initial Release 15 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. *For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL28113, ISL28213, ISL28413 To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff FITs are available from our website at http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Small Outline Transistor Plastic Packages (SC70-5) P5.049 D VIEW C e1 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE INCHES 5 SYMBOL 4 E CL 1 2 CL 3 e E1 b CL 0.20 (0.008) M C C CL A A2 SEATING PLANE A1 -C- PLATING b1 0.043 0.80 1.10 - 0.004 0.00 0.10 - A2 0.031 0.039 0.80 1.00 - b 0.006 0.012 0.15 0.30 - b1 0.006 0.010 0.15 0.25 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.009 0.08 0.20 6 D 0.073 0.085 1.85 2.15 3 E 0.071 0.094 1.80 2.40 - E1 0.045 0.053 1.15 1.35 3 e 0.0256 Ref 0.65 Ref - e1 0.0512 Ref 1.30 Ref - L2 c1 NOTES 0.031 0.010 0.018 0.017 Ref. 0.26 0.46 4 0.420 Ref. 0.006 BSC 0o N c MAX 0.000 α WITH MIN A L b MILLIMETERS MAX A1 L1 0.10 (0.004) C MIN - 0.15 BSC 8o 0o 5 8o - 5 5 R 0.004 - 0.10 - R1 0.004 0.010 0.15 0.25 Rev. 3 7/07 NOTES: BASE METAL 1. Dimensioning and tolerances per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC70 and JEDEC MO-203AA. 4X θ1 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. 5. “N” is the number of terminal positions. R GAUGE PLANE SEATING PLANE L C L1 α L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. 4X θ1 VIEW C 0.4mm 0.75mm 2.1mm 0.65mm TYPICAL RECOMMENDED LAND PATTERN 17 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Package Outline Drawing P5.064A 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 0, 2/10 1.90 0-3° D A 0.08-0.20 5 4 PIN 1 INDEX AREA 2.80 3 1.60 3 0.15 C D 2x 2 5 (0.60) 0.20 C 2x 0.95 SEE DETAIL X B 0.40 ±0.05 3 END VIEW 0.20 M C A-B D TOP VIEW 10° TYP (2 PLCS) 2.90 5 H 0.15 C A-B 2x C 1.45 MAX 1.14 ±0.15 0.10 C SIDE VIEW SEATING PLANE (0.25) GAUGE PLANE 0.45±0.1 0.05-0.15 4 DETAIL "X" (0.60) (1.20) NOTES: (2.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. This dimension is measured at Datum “H”. 6. Package conforms to JEDEC MO-178AA. (0.95) (1.90) TYPICAL RECOMMENDED LAND PATTERN 18 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Package Outline Drawing M8.118A 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP) Rev 0, 9/09 3.0±0.1 8 A 0.25 CAB 3.0±0.1 4.9±0.15 DETAIL "X" 1.10 Max PIN# 1 ID B SIDE VIEW 2 1 0.18 ± 0.05 2 0.65 BSC TOP VIEW 0.95 BSC 0.86±0.09 H GAUGE PLANE C 0.25 SEATING PLANE 0.33 +0.07/ -0.08 0.08 C A B 0.10 ± 0.05 3°±3° 0.10 C 0.55 ± 0.15 DETAIL "X" SIDE VIEW 1 5.80 NOTES: 4.40 3.00 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSE Y14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.25mm max per side are not included. 5. Dimensions “D” and “E1” are measured at Datum Plane “H”. 6. This replaces existing drawing # MDP0043 MSOP 8L. 0.65 0.40 1.40 TYPICAL RECOMMENDED LAND PATTERN 19 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 ± 0.10 A DETAIL "A" 0.22 ± 0.03 B 6.0 ± 0.20 3.90 ± 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45° 4° ± 4° 0.43 ± 0.076 1.27 0.25 M C A B SIDE VIEW “B” TOP VIEW 1.75 MAX 1.45 ± 0.1 0.25 GAUGE PLANE C SEATING PLANE 0.10 C 0.175 ± 0.075 SIDE VIEW “A 0.63 ±0.23 DETAIL "A" (0.60) (1.27) NOTES: (1.50) (5.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. 6. Reference to JEDEC MS-012. TYPICAL RECOMMENDED LAND PATTERN 20 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 21 FN6728.5 June 9, 2011 ISL28113, ISL28213, ISL28413 Thin Shrink Small Outline Package Family (TSSOP) MDP0044 0.25 M C A B D THIN SHRINK SMALL OUTLINE PACKAGE FAMILY A MILLIMETERS (N/2)+1 N SYMBOL 14 LD 16 LD 20 LD 24 LD 28 LD TOLERANCE PIN #1 I.D. E E1 1 (N/2) B 0.20 C B A 2X N/2 LEAD TIPS TOP VIEW 0.05 e C SEATING PLANE H A 1.20 1.20 1.20 1.20 1.20 Max A1 0.10 0.10 0.10 0.10 0.10 ±0.05 A2 0.90 0.90 0.90 0.90 0.90 ±0.05 b 0.25 0.25 0.25 0.25 0.25 +0.05/-0.06 c 0.15 0.15 0.15 0.15 0.15 +0.05/-0.06 D 5.00 5.00 6.50 7.80 9.70 ±0.10 E 6.40 6.40 6.40 6.40 6.40 Basic E1 4.40 4.40 4.40 4.40 4.40 ±0.10 e 0.65 0.65 0.65 0.65 0.65 Basic L 0.60 0.60 0.60 0.60 0.60 ±0.15 L1 1.00 1.00 1.00 1.00 1.00 Reference Rev. F 2/07 0.10 M C A B b 0.10 C N LEADS NOTES: 1. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15mm per side. SIDE VIEW 2. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm per side. SEE DETAIL “X” 3. Dimensions “D” and “E1” are measured at dAtum Plane H. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c END VIEW L1 A A2 GAUGE PLANE 0.25 L A1 0° - 8° DETAIL X 22 FN6728.5 June 9, 2011