NB3V63143G D

NB3V63143G
1.8 V Programmable
OmniClock Generator
with Single Ended (LVCMOS) and Differential
(LVDS/HCSL) Outputs with Individual Output
Enable and Individual VDDO
The NB3V63143G, which is a member of the OmniClock family, is
a one−time programmable (OTP), low power PLL−based clock
generator that supports any output frequency from 8 kHz to 200 MHz.
The device accepts fundamental mode parallel resonant crystal or a
single ended (LVCMOS) reference clock as input. It generates either
three single ended (LVCMOS) outputs, or one single ended output and
one differential (LVDS/HCSL) output. The output signals can be
modulated using the spread spectrum feature of the PLL
(programmable spread spectrum type, deviation and rate) for
applications demanding low electromagnetic interference (EMI).
Individual output enable pins OE[2:0] are available to enable/disable
the outputs. Individual output voltage pins VDDO[2:0] are available
to independently set the output voltage of each output. Up to four
different configurations can be written into the device memory. Two
selection pins (SEL[1:0]) allow the user to select the configuration to
use. Using the PLL bypass mode, it is possible to get a copy of the
input clock on any or all of the outputs. The device can be powered
down using the Power Down pin (PD#). It is possible to program the
internal input crystal load capacitance and the output drive current
provided by the device. The device also has automatic gain control
(crystal power limiting) circuitry which avoids the device overdriving
the external crystal.
Features
• Member of the OmniClock Family of Programmable
•
•
•
•
•
•
•
•
January, 2016 − Rev. 2
1
QFN16
CASE 485AE
MARKING DIAGRAM
3V631
43Gxx
ALYWG
G
3V63143G
xx
A
L
Y
W
G
= Specific Device Code
= Specific Program Code (Default
‘00’ for Unprogrammed Part)
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information on page 20 of
this data sheet.
• Programmable Internal Crystal Load Capacitors
• Programmable Output Drive Current for Single Ended
Clock Generators
Operating Power Supply: 1.8 V ± 0.1 V
I/O Standards
♦ Inputs: LVCMOS, Fundamental Mode Crystal
♦ Outputs: 1.8 V LVCMOS
♦ Outputs: LVDS and HCSL
3 Programmable Single Ended (LVCMOS) Outputs
from 8 kHz to 200 MHz
1 Programmable Differential Clock Output up to
200 MHz
Input Frequency Range
♦ Crystal: 3 MHz to 50 MHz
♦ Reference Clock: 3 MHz to 200 MHz
Configurable Spread Spectrum Frequency Modulation
Parameters (Type, Deviation, Rate)
Individual Output Enable Pins
Independent Output Voltage Pins
© Semiconductor Components Industries, LLC, 2016
www.onsemi.com
•
•
•
•
•
•
•
Outputs
Power Saving Mode through Power Down Pin
Programmable PLL Bypass Mode
Programmable Output Inversion
Programming and Evaluation Kit Available for Field
Programming and Quick Evaluation
Temperature Range −40°C to 85°C
Packaged in 16−pin QFN
These are Pb−Free Devices
Typical Applications
• eBooks and Media Players
• Smart Wearables, Smart Phones, Portable Medical and
•
1
Industrial Equipment
Set Top Boxes, Printers, Digital Cameras and
Camcorders
Publication Order Number:
NB3V63143G/D
NB3V63143G
BLOCK DIAGRAM
VDD
PD#
SEL0
SEL1
Input
Decoder
Output control
Crystal/Clock Control
Configuration
Memory
VDDO0
Frequency
and SS
Reference XIN/ CLKIN
Clock
Crystal
XOUT
Output
Divider
PLL Block
CMOS/
DIFF
buffer
OE0
Clock Buffer/
Crystal
Oscillator And
AGC
Phase
Detector
Charge
Pump
VDDO1
VCO
Output
Divider
CMOS/
DIFF
buffer
Feedback
Divider
VDDO2
PLL Bypass Mode
Notes:
1. CLK0 and CLK1 can be configured to be one LVDS or HCSL output, or two single ended LVCMOS outputs.
2. Dotted lines are the programmable control signals to internal IC blocks.
3. OE[2:0], SEL[1:0] have internal pull up resistors. PD# has internal pull down resistor.
Figure 1. Simplified Block Diagram
XOUT
2
SEL0
SEL1
VDDO2
CLK2
PIN FUNCTION DESCRIPTION
1
16
15
14
13
NB3V63143G
12
VDD
11
VDDO1
GNDO
(EPAD)
10
CLK1
GND
4
9
CLK0
OE1
OE0
6
7
8
VDDO0
3
OE2
PD#
5
Figure 2. Pin Connections (Top View) − QFN16 (with EPAD)
www.onsemi.com
2
CMOS
buffer
CLK2
OE2
GNDO
XIN/CLKIN
CLK1
OE1
Output
Divider
GND
CLK0
NB3V63143G
Table 1. PIN DESCRIPTION
Pin No.
Pin Name
Pin Type
1
XIN/CLKIN
Input
3 MHz to 50 MHz crystal input connection or an external single ended reference
input clock between 3 MHz and 200 MHz.
Description
2
XOUT
Output
Crystal output. Float this pin when external reference clock is connected at XIN.
3
PD#
Input
4
GND
Ground
5, 6, 7
OE[2:0]
Input
8
VDDO0
Power
9
CLK0
SE/DIFF Output
Supports 8 kHz to 200 MHz Single Ended (LVCMOS) signals or Differential
(LVDS/HCSL) signals. Using PLL Bypass mode, the output can also be a copy of
the input clock. The single ended output will be LOW and differential outputs will be
complementary LOW/HIGH until the PLL has locked and the frequency has
stabilized.
10
CLK1
SE/DIFF Output
Supports 8 kHz to 200 MHz Single Ended (LVCMOS) signals or Differential
(LVDS/HCSL) signals. Using PLL Bypass mode, the output can also be a copy of
the input clock. The single ended output will be LOW and differential outputs will be
complementary LOW/HIGH until the PLL has locked and the frequency has
stabilized.
11
VDDO1
Power
CLK1 Output power supply ≤ VDD
12
VDD
Power
1.8 V power supply.
13
CLK2
SE Output
14
VDDO2
Power
15, 16
SEL[1:0]
Input
EPAD
GNDO
Ground
Asynchronous LVCMOS input. Active Low Master Reset to disable the device and
set outputs Low. Internal pull−down resistor. This pin needs to be pulled High for
normal operation of the chip.
Power supply ground.
2−Level LVCMOS Inputs for Enabling/Disabling output clocks CLK[2:0] respectively.
Internal pull−up resistor.
CLK0 Output power supply ≤ VDD
Supports 8 kHz to 200 MHz Single Ended (LVCMOS) signals. Using PLL Bypass
mode, the output can also be a copy of the input clock. The single ended output will
be LOW until the PLL has locked and the frequency has stabilized.
CLK2 Output power supply ≤ VDD
2−Level LVCMOS Inputs for Configuration Selection. Configuration parameters
include individual output frequencies, spread spectrum configuration, enable/disable
status of each output, output type, internal crystal load capacitance configuration,
etc. Configuration can be switched dynamically, but may require the PLL to re−lock.
Internal pull−up resistor.
Power supply ground for Outputs.
Table 2. OUTPUT CONFIGURATION SELECT
FUNCTION TABLE
Table 4. OUTPUT ENABLE FUNCTION TABLE
SEL1
SEL0
Output Configuration
L
L
I
L
H
II
H
L
III
H
H
IV
OE[2:0]
Function
0
CLK Disabled
1
CLK Enabled
TYPICAL CRYSTAL PARAMETERS
Crystal: Fundamental Mode Parallel Resonant
Frequency: 3 MHz to 50 MHz
Table 3. POWER DOWN FUNCTION TABLE
Table 5. MAX CRYSTAL LOAD CAPACITORS
RECOMMENDATION
PD#
Function
0
Device Powered Down
Crystal Frequency Range
Max Cap Value
1
Device Powered Up
3 MHz − 30 MHz
20 pF
30 MHz − 50 MHz
10 pF
Shunt Capacitance (C0): 7 pF (Max)
Equivalent Series Resistance 150 W (Max)
www.onsemi.com
3
NB3V63143G
FUNCTIONAL DESCRIPTION
The NB3V63143G is a 1.8 V programmable, single
ended/differential clock generator, designed to meet the
timing requirements for consumer and portable markets. It
has a small package size and it requires low power during
operation and while in standby. This device provides the
ability to configure a number of parameters as detailed in the
following section. The One−Time Programmable memory
allows programming and storing of up to four configurations
in the memory space.
1.8 V
VDDO0
R (Optional)
0.1 mF
R (Optional)
0.01 mF
0.1 mF
0.01 mF
VDD
Crystal or
Reference
Clock Input
VDDO0
XIN/CLKIN
VDDO1
XOUT
VDDO1
R (Optional)
0.1 mF
0.01 mF
VDDO2
R (Optional)
VDDO2
0.1 mF
NB3V63143G
0.01 mF
SEL0
GND
GNDO
CLK2
SEL1
Single Ended Clock
CLK1
CLK0
Single Ended Clocks
or
Differential Clock
LVDS/HCSL
PD# OE0 OE1 OE2
Figure 3. Power Supply and Output Supply Noise Suppression
Power Supply
power supply can be as high as VDD. This feature removes
the need for external voltage converters for each of the
outputs thus reducing component count, saving board space
and facilitating board design. In order to suppress power
supply noise it is recommended to connect decoupling
capacitors of 0.1 mF and 0.01 mF close to each VDDO pin as
shown in Figure 3.
Device Supply
The NB3V63143G is designed to work with a 1.8 V VDD
power supply. For VDD operation of 3.3 V/2.5 V, refer to
the NB3H63143G datasheet. In order to suppress power
supply noise it is recommended to connect decoupling
capacitors of 0.1 mF and 0.01 mF close to the VDD pin as
shown in Figure 3.
Output Power Supply
Each output CLK[2:0] has a separate output power supply
VDDO[2:0] pin to control its output voltage. The output
www.onsemi.com
4
NB3V63143G
Clock Input
maintain a good quality input clock signal level. This feature
takes care of low clock swings fed from external reference
clocks and ensures proper device operation. It also enables
maximum compatibility with crystals from different
manufacturers, processes, quality and performance. AGC
also takes care of power dissipation in the crystal; avoids
overdriving the crystal and thus extending the crystal life. In
order to calculate the AGC gain accurately and avoid
increasing the jitter on the output clocks, the user needs to
provide the crystal load capacitance as well as other crystal
parameters like ESR and shunt capacitance (C0).
Input Frequency
The clock input block can be programmed to use
a fundamental mode crystal from 3 MHz to 50 MHz or
a single ended reference clock source from 3 MHz to
200 MHz. When using output frequency modulation for
EMI reduction, for optimal performance, it is recommended
to use crystals with a frequency greater than 6.75 MHz as
input. Crystals with ESR values of up to 150 W are
supported. While using a crystal as input, it is important to
set crystal load capacitor values correctly to achieve good
performance.
Programmable Clock Outputs
Programmable Crystal Load Capacitors
Output Type and Frequency
The provision of internal programmable crystal load
capacitors eliminates the necessity of external load
capacitors for standard crystals. The internal load capacitors
can be programmed to any value between 4.36 pF and
20.39 pF with a step size of 0.05 pF. Refer to Table 5 for
recommended maximum load capacitor values for stable
operation. There are three modes of loading the crystal −
with internal chip capacitors only, with external capacitors
only or with the both internal and external capacitors. Check
with the crystal vendor’s load capacitance specification for
setting of the internal load capacitors. The minimum value
of 4.36 pF internal load capacitor need to be considered
while selecting external capacitor value. The internal load
capacitors will be bypassed when using an external
reference clock.
The NB3V63143G provides three independent single
ended LVCMOS outputs, or one single ended LVCMOS
output and one LVDS/HCSL differential output. The device
supports any single ended output or differential output
frequency from 8 kHz up to 200 MHz with or without
frequency modulation. All outputs have individual output
enable pins (refer to the Output Enable/Disable section on
page 7). It should be noted that certain combinations of
output frequencies and spread spectrum configurations may
not be recommended for optimal and stable operation.
For differential clocking, CLK0 and CLK1 can be
configured as LVDS or HCSL. While using differential
signaling format at the output, it is required to use only
VDDO1 as output supply and use only the OE1 pin for the
output enable function. (refer to the Application Schematic
in Figure 4). When all 3 outputs are single ended, VDDO0
and OE0 have normal functionality.
Automatic Gain Control (AGC)
The Automatic Gain Control (AGC) feature adjusts the
gain to the input clock based on its signal strength to
VDDO2 ≤ VDD
Crystal or
Reference
Clock Input
VDDO2
XIN/CLKIN
CLK2
XOUT
NB3V63143G
Single Ended Clock
VDDO1 ≤ VDD
VDDO1
VDDO0
CLK1
CLK0
OE2
PD#
Differential Clock
LVDS/HCSL
OE0
OE1
Figure 4. Application Setup for Differential Output Configuration
Programmable Output Drive
provides further load drive and signal conditioning as per the
application requirement.
The drive strength or output current of each of the
LVCMOS clock outputs is programmable independently.
For each VDDO supply voltage, four distinct levels of
LVCMOS output drive strengths can be selected as
mentioned in DC Electrical Characteristics. This feature
PLL BYPASS Mode
PLL Bypass mode can be used to buffer the input clock on
any of the outputs or all of the outputs. Any of the clock
outputs can be programmed to generate a copy of the input
clock.
www.onsemi.com
5
NB3V63143G
Output Inversion
modulates the output of its PLL in order to “spread” the
bandwidth of the synthesized clock, decreasing the peak
amplitude at the center frequency and at the frequency’s
harmonics. This results in significantly lower system EMI
compared to the typical narrow band signal produced by
oscillators and most clock generators. Lowering EMI by
increasing a signal’s bandwidth is called ‘spread spectrum
modulation’.
All output clocks of the NB3V63143G can be phase
inverted relative to each other. This feature can also be used
in conjunction with the PLL BYPASS mode.
Spread Spectrum Frequency Modulation
Spread spectrum is a technique using frequency
modulation to achieve lower peak electromagnetic
interference (EMI). It is an elegant solution compared to
techniques of filtering and shielding. The NB3V63143G
Figure 5. Frequency Modulation or Spread Spectrum Clock for EMI Reduction
For example, the minimum recommended reference
frequency for a modulation rate of 30 kHz would be
30 kHz * 225 = 6.75 MHz. For 27 MHz, the maximum
recommended
modulation
rate
would
be
27 MHz / 225 = 120 kHz
The outputs of the NB3V63143G can be programmed to
have either center spread from ±0.125% to ±3% or down
spread from −0.25% to −4%. The programmable step size
for spread spectrum deviation is 0.125% for center spread
and 0.25% for down spread respectively. Additionally, the
frequency modulation rate is also programmable.
Frequency modulation from 30 kHz to 130 kHz can be
selected. Spread spectrum, when on, applies to all the
outputs of the device but not to output clocks that use the
PLL bypass feature. There exists a tradeoff between the
input clock frequency and the desired spread spectrum
profile. For certain combinations of input frequency and
modulation rate, the device operation could be unstable and
should be avoided. For spread spectrum applications, the
following limits are recommended:
Fin (Min) = 6.75 MHz
Fmod (range) = 30 kHz to 130 kHz
Fmod (Max) = Fin / 225
Control Inputs
Configuration Space Selection
The SEL[1:0] pins are used to select one of the
pre−programmed configurations statically or dynamically
while the device is powered on. These pins are 2−level
LVCMOS. Up to four configurations can be stored in the
memory space of the device. Clock outputs can be
independently enabled or disabled through the
configuration space. To have a given clock output enabled,
it must be enabled in both the configuration space and
through its respective output enable pin.
The PLL re−locking and stabilization time must be taken
into consideration when dynamically changing the
configurations. Table 6 shows an example of four
configurations.
For any input frequency selected, the above limits must be
observed for a good spread spectrum profile.
Table 6. EXAMPLE CONFIGURATION SPACE SETTINGS
Configuration
Selection
Input
Frequency
Output
Frequency
VDD
VDDO
SS%
SS Mod
Rate
Output
Drive
Output
Inversion
Output
Enable
PLL
Bypass
I
25 MHz
CLK0=100 MHz
CLK1=8 kHz
CLK2=25 MHz
1.8 V
VDDO0=1.8 V
VDDO1=1.8 V
VDDO2=1.8 V
−0.5%
110 kHz
CLK0=8mA
CLK1=4mA
CLK2=2mA
CLK0=N
CLK1=N
CLK2=Y
CLK0=Y
CLK1=Y
CLK2=Y
CLK0=N
CLK1=N
CLK2=Y
CLK2
Ref clk
II
40 MHz
CLK0=125 MHz
CLK1=40 MHz
CLK2=10 MHz
1.8 V
VDDO0=1.8 V
VDDO1=1.8 V
VDDO2=1.8 V
±0.25%
30 kHz
CLK0=4mA
CLK1=4mA
CLK2=4mA
CLK0=N
CLK1=N
CLK2=N
CLK0=Y
CLK1=Y
CLK2=Y
CLK0=N
CLK1=Y
CLK2=N
CLK1
Ref clk
III
100 MHz
CLK0=100 MHz
CLK1=100 MHz
CLK2=100 MHz
1.8 V
VDDO0=1.8 V
VDDO1=1.8 V
VDDO2=1.8 V
No SS
NA
CLK0=8mA
CLK1=4mA
CLK2=2mA
CLK0=N
CLK1=Y
CLK2=Y
CLK0=Y
CLK1=Y
CLK2=Y
CLK0=Y
CLK1=Y
CLK2=Y
All Three
Outputs
are Ref
clks
IV
25 MHz
CLK0=100 MHz
CLK1=100 MHz
CLK2=48 MHz
1.8 V
VDDO0=NA
VDDO1=1.8 V
VDDO2=1.8 V
−1%
100 kHz
CLK2=8mA
CLK0=NA
CLK1=NA
CLK2=N
CLK0=NA
CLK1=Y
CLK2=Y
CLK0=NA
CLK1=N
CLK2=N
CLK[1:0] is
Differential
Output
www.onsemi.com
6
Notes
NB3V63143G
Output Enable/Disable
device functions are disabled by default and when the PD#
pin is pulled high the device functions are activated.
Output Enable pins (OE[2:0]) are LVCMOS input pins
that individually enable or disable the outputs CLK[2:0]
respectively. These inputs only disable the output buffers
thus not affecting the rest of the blocks on the device. When
using a differential output, only the OE1 pin must be used to
enable/disable the differential output (the OE0 pin will be
ignored). The hardware OE pins have an effect only when
the respective outputs are enabled in the configuration
space. The output disable state can be set to high impedance
(Hi−Z) or Low.
Default Device State
The
NB3V63143G
parts
shipped
from
ON Semiconductor are blank, with no inputs/outputs
programmed. The parts need to be programmed by the field
sales or by a distributor or by the users themselves before
they can be used. Programmable clock software
downloadable from the ON Semiconductor website can be
used along with the programming kit to achieve this
purpose. For mass production, parts can be factory
programmed with a customer qualified configuration and
sourced from ON Semiconductor as a dash part number (Eg.
NB3V63143G−01).
Power Down
Power saving mode can be activated though the power
down PD# input pin. This input is an LVCMOS active Low
Master Reset that disables the device and sets the outputs
Low. By default it has an internal pull−down resistor. The
Table 7. ATTRIBUTES
Characteristic
Value
ESD Protection − Human Body Model
2 kV
Internal Input Default State Pull Up/Down Resistor
50 kW
Moisture Sensitivity, Indefinite Time Out of Dry Pack
(Note 1)
MSL1
Flammability Rating − Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125in
Transistor Count
130k
Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
1. For additional information, see Application Note AND8003/D.
ABSOLUTE MAXIMUM RATINGS (Note 2)
Symbol
VDD
Parameter
Positive Power Supply with Respect to Ground
Rating
Unit
−0.5 to +4.6
V
VI
Input Voltage with Respect to Chip Ground
−0.5 to VDD + 0.5
V
TA
Operating Ambient Temperature Range (Industrial Grade)
−40 to +85
°C
TSTG
Storage Temperature
−65 to +150
°C
TSOL
Max. Soldering Temperature (10 sec)
265
°C
32.3
24.22
°C/W
°C/W
qJA
Thermal Resistance (Junction−to−Ambient) (Note 3)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction−to−Case)
3.6
°C/W
TJ
Junction Temperature
125
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and not valid simultaneously.
If stress limits are exceeded device functional operation is not implied, damage may occur and reliability may be affected.
3. JEDEC standard multilayer board − 2S2P (2 signal, 2 power). JESD51.7 type board. Back side Copper heat spreader area 100 sqmm, 2 oz
(0.070mm) copper thichness.
www.onsemi.com
7
NB3V63143G
RECOMMENDED OPERATING CONDITIONS
Symbol
Min
Typ
Max
Unit
Core Power Supply Voltage
1.8 V operation
1.7
1.8
1.9
V
Output Power Supply Voltage (Note 4)
1.8 V operation
1.7
1.8
1.9
V
Clock output load capacitance for
LVCMOS clock
fout < 100 MHz
fout ≥ 100 MHz
15
5
pF
Crystal Input Frequency
Reference Clock Frequency
Fundamental Crystal
Single ended clock input
50
200
MHz
CX
Xin / Xout pin stray capacitance
(Note 5)
4.5
CXL
Crystal load capacitance
(Note 6)
10
ESR
Crystal ESR
VDD
VDDO[2:0]
CL
fclkin
Parameter
Condition
3
3
pF
pF
150
W
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
4. The output power supply voltage VDDO[2:0] must always be less than or equal to core power supply voltage VDD.
5. The Xin/ Xout pin stray capacitance needs to be subtracted from crystal load capacitance (along with PCB and trace capacitance) while
selecting appropriate load for the crystal in order to get minimum ppm error.
6. Refer to XTAL parameters supplied by the vendor.
DC ELECTRICAL CHARACTERISTICS
(VDD = 1.8 V ± 0.1V, VDDO[2:0] = 1.8 V ± 0.1V; GND = 0 V, TA = −40°C to 85°C, Notes 7 & 16)
Parameter
Symbol
IDD_1.8 V
Condition
Min
Typ
Max
Power Supply Current for
Core
Configuration Dependent. VDD = 1.8 V,
TA = 25°C, XIN/CLKIN = 25 MHz
(XTAL), CLK[0:2] = 100 MHz, 8 mA
output drive
IPD
Power Down Supply Current
PD# is Low to Make All Outputs OFF
20
mA
VIH
Input HIGH Voltage
Pins XIN, SEL[1:0], OE[2:0]
0.65 VDD
VDD
V
Pin PD#
0.85 VDD
VDD
Pins XIN, SEL[1:0], OE[2:0]
0
0.35 VDD
Pin PD#
0
0.15 VDD
VIL
Input LOW Voltage
13
Unit
mA
V
Zo
Nominal Output Impedance
Configuration Dependent. 8 mA Drive
22
W
RPUP/PD
Internal Pull Up/ Pull Down
Resistor
VDD = 1.8 V
150
kW
Cprog
Programmable Internal
Crystal Load Capacitance
Configuration Dependent
4.36
Programmable Internal
Crystal Load Capacitance
Resolution
Cin
Input Capacitance
20.39
pF
6
pF
0.05
Pins PD#, SEL[1:0], OE[2:0]
4
LVCMOS OUTPUTS
VOH
VOL
Output HIGH Voltage
0.75xVDDO
VDDO = 1.8 V
IOH = 1 mA
IOH = 2 mA
IOH = 4 mA
IOH = 8 mA
VDDO = 1.8 V
IOL = 1 mA
IOL = 2 mA
IOL = 4 mA
IOL = 8 mA
Output LOW Voltage
V
0.25xVDDO
www.onsemi.com
8
V
NB3V63143G
DC ELECTRICAL CHARACTERISTICS (continued)
(VDD = 1.8 V ± 0.1V, VDDO[2:0] = 1.8 V ± 0.1V; GND = 0 V, TA = −40°C to 85°C, Notes 7 & 16)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
LVCMOS OUTPUTS
IDDO_LVCMOS
LVCMOS Output Supply
Current
Configuration Dependent. TA = 25°C,
CLK[0:2] = fout in PLL bypass mode
Measured on VDDO = 1.8 V
fout = 33.33 MHz, CL = 5 pF
fout = 100 MHz, CL = 5 pF
fout = 200 MHz, CL = 5 pF
mA
3
8
16
HCSL OUTPUTS (Note 8)
VOH_HCSL
VOL_HCSL
VCROSS
Output HIGH Voltage (Note 9)
mV
VDDO = 1.8 V
700
VDDO = 1.8 V
0
Output Low Voltage (Note 9)
mV
Crossing Point Voltage (Notes 10 and 11)
mV
VDDO = 1.8 V
Delta Vcross
Change in Magnitude of Vcross for HCSL Output (Notes 10 and 12)
VDDO = 1.8 V
IDDO_HCSL
Measured on VDDO0 = 1.8 V with
250
350
450
150
fout = 100 MHz, CL = 2 pF
fout = 200 MHz, CL = 2 pF
22
mV
mA
LVDS OUTPUTS (Notes 10 and 13)
VOD_LVDS
Differential Output Voltage
DeltaVOD_LVDS Change in Magnitude of VOD for Complementary Output States
VOS_LVDS
Offset Voltage
Delta
VOS_LVDS
Change in Magnitude of VOS for Complementary Output States
VOH_LVDS
Output HIGH Voltage (Note 14)
VDDO = 1.8 V
VOL_LVDS
Output LOW Voltage (Note 15)
VDDO = 1.8 V
250
450
mV
0
25
mV
VDDO = 1.8 V
IDDO_LVDS
fout = 100 MHz
fout = 200 MHz
900
0
1100
700
mV
25
mV
1250
mV
800
mV
14
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm.
7. Measurement taken with single ended clock outputs terminated with test load capacitance of 5 pF and 15 pF and differential clock
terminated with test load of 2 pF. See Figures 6, 7 and 10.
8. Measurement taken with outputs terminated with RS = 0 W, RL = 50 W, with test load capacitance of 2 pF. See Figure 8. Guaranteed by
characterization.
9. Measurement taken from single ended waveform.
10. Measured at crossing point where the instantaneous voltage value of the rising edge of CLKx+ equals the falling edge of CLKx−.
11. Refers to the total variation from the lowest crossing point to the highest, regardless of which edge is crossing. Refers to all crossing points
for this measurement.
12. Defined as the total variation of all crossing voltage of rising CLKx+ and falling CLKx−. This is maximum allowed variance in the VCROSS
for any particular system.
13. LVDS outputs require 100 W receiver termination resistor between differential pair. See Figure 9.
14. VOHmax = VOSmax + 1/2 VODmax.
15. VOLmax = VOSmin − 1/2 VODmax.
16. Parameter guaranteed by design verification not tested in production.
www.onsemi.com
9
NB3V63143G
AC ELECTRICAL CHARACTERISTICS (VDD = 1.8 V ± 0.1 V, VDDO[2:0] = 1.8 V ± 0.1 V; VDDO ≤ VDD, GND = 0 V,
TA = −40°C to 85°C, Notes 16, 17, 20, 21 and 22)
Symbol
fout
fMOD
SS
SSstep
SSCRED
Parameter
Condition
Min
Single Ended Output
Frequency
Typ
Max
Unit
0.008
200
MHz
Spread Spectrum Modulation
Rate
fclkin ≥ 6.75 MHz
30
130
kHz
Percent Spread Spectrum
(deviation from nominal
frequency)
Down Spread
0
−4
%
Center Spread
0
±3
%
Percent Spread Spectrum
Change Step Size
Down Spread Step Size
0.25
%
Center Spread Step Size
0.125
%
Spectral Reduction,
3rd harmonic
@SS = −0.5%, fout = 100 MHz,
fclkin = 25 MHz Crystal, RES BW at
30 kHz, All Output Types
−10
dB
tPU
Stabilization Time from
Power−up
VDD = 1.8 V with Frequency
Modulation ON
3.0
ms
tPD
Stabilization Time from
Power Down
Time from falling edge on PD pin to
Tri−stated Outputs (Asynchronous)
3.0
ms
tSEL
Stabilization Time from
Change of Configuration
With Frequency Modulation ON
3.0
ms
tOE1
Output Enable Time
Time from rising edge on OE pin to
valid clock outputs (asynchronous)
2/fout
(MHz)
ms
tOE2
Output Disable Time
Time from falling edge on OE pin to
valid clock outputs (asynchronous)
2/fout
(MHz)
ms
Synthesis Error
Configuration Dependent
0
ppm
Eppm
SINGLE ENDED OUTPUTS (VDD = 1.8 V ± 0.1V, VDDO[2:0] = 1.8 V ± 0.1V; VDDO ≤ VDD, GND = 0 V, TA = −40 to 85°C) (Notes 16, 17,
20, 21 and 22)
tJITTER−1.8 V
tr / tf 1.8 V
tDC
Period Jitter Peak−to−Peak
25 MHz xtal input, fout = 100 MHz,
SS off, Configuration Dependent
(Note 22, see Figure 12)
100
Cycle−Cycle Jitter
25 MHz xtal input, fout = 100 MHz,
SS off, Configuration Dependent
(Note 22, see Figure 12)
100
Rise/Fall Time
Measured between 20% to 80% with
15 pF load, fout = 100 MHz,
VDD = VDDO = 1.8 V,
Max Drive
Min Drive
Output Clock Duty Cycle
VDD = 1.8 V; VDDO ≤ VDD
Duty Cycle of Ref clock is 50%
PLL Clock
Reference Clock
ps
ns
1
2
%
45
40
50
50
55
60
DIFFERENTIAL OUTPUT (CLK1, CLK0) (VDD = 1.8 V ± 0.1V, VDDO[2:0] = 1.8 V ± 0.1V; VDDO ≤ VDD, GND = 0 V, TA = −40 to 85°C)
(Notes 16, 17, 20, 21 and 22)
tJITTER−1.8 V
tr 1.8 V
Period Jitter Peak−to−Peak
Configuration Dependent. 25 MHz xtal
input, fout = 100 MHz, SS off, CLK2 =
OFF (Note 18, 20 and 22, see
Figure 12)
100
Cycle−Cycle Jitter
Configuration Dependent. 25 MHz xtal
input, fout = 100 MHz, SS off, CLK2 =
OFF (Note 19, 20 and 22, see
Figure 12)
100
Rise Time
Measured between 20% to 80%,
VDD = 1.8 V
175
LVDS
HCSL
www.onsemi.com
10
ps
700
ps
NB3V63143G
AC ELECTRICAL CHARACTERISTICS (continued)(VDD = 1.8 V ± 0.1 V, VDDO[2:0] = 1.8 V ± 0.1 V; VDDO ≤ VDD, GND = 0 V,
TA = −40°C to 85°C, Notes 16, 17, 20, 21 and 22)
Symbol
Parameter
Condition
Min
Typ
Max
Unit
DIFFERENTIAL OUTPUT (CLK1, CLK0) (VDD = 1.8 V ± 0.1V, VDDO[2:0] = 1.8 V ± 0.1V; VDDO ≤ VDD, GND = 0 V, TA = −40 to 85°C)
(Notes 16, 17, 20, 21 and 22)
tf 1.8 V
tDC
Fall Time
Measured between 20% to 80% with
2 pF load, VDD = 1.8 V
LVDS
HCSL
Output Clock Duty Cycle
VDD = 1.8 V;
Duty Cycle of Ref clock is 50%
PLL Clock
Reference Clock
175
700
ps
%
45
40
50
50
55
60
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board
with maintained transverse airflow greater than 500 lfpm.
17. Measurement taken from single ended clock terminated with test load capacitance of 5 pF and 15 pF and differential clock terminated with
test load of 2 pF. See Figures 6, 7 and 10.
18. Measurement taken from single ended waveform.
19. Measurement taken from differential waveform.
20. AC performance parameters like jitter change based on the output frequency, spread selection, power supply and loading conditions of the
output. For application specific AC performance parameters, please contact ON Semiconductor.
21. Measured at fout = 100 MHz, No Frequency Modulation, fclkin = 25 MHz fundamental mode crystal and output termination as described in
Parameter Measurement Test Circuits
22. Period jitter Sampled with 10000 cycles, Cycle−cycle jitter sampled with 1000 cycles. Jitter measurement may vary. Actual jitter is dependent
on Input jitter and edge rate, number of active outputs, inputs and output frequencies, supply voltage, temperature, and output load.
www.onsemi.com
11
SEL1
SEL1
NB3V63143G
www.onsemi.com
12
OE0
1.8 V
1.8 V
VDDO1
VDDO0
VDD
−
−
VDD
1.8 V
VDDO2
1.8 V (LVDS/HCSL)
−
−
VDD
1.8 V
VDD
VDD
1.8 V
MIN
1.8 V
MAX
Differential Signal
OE2
1.8 V
OE1
MIN
Single Ended Signal
PD#
RL
Zo = 50 W
Optional
Optional
LVDS
HCSL
100
Open
RD
Open
Open
50
RL
Open
Open
2 pF
CL
Open
Differential Clock Termination
CL
CL
RD
Open
Open
RC
Open
Open
Open
RV
Open
Receiver
VCC
23. Receiver VCC must be at same supply potential as VDDO1 for differential clock outputs.
24. All resistor values are in ohms.
25. VDDO [2:0] <= VDD always
RS
Optional
Zo = 50 W
Zo = 50 W
Differential Clock
Single Ended Clock
Signaling Type
LVCMOS
RL
RS (Optional)
RS (Optional)
RS (Optional)
MAX
CLK0
CLK1
CLK2
PD# OE0 OE1 OE2 GND GNDO
SEL0
XOUT
VDDO1 VDDO0
VDDO1 VDDO2 VDDO0
VDDO2
XIN/CLKIN
VDD
SEL0
Reference
Clock
Input
or Crystal
1.8 V
NB3V63143G
SCHEMATIC FOR OUTPUT TERMINATION
Figure 6. Typical Termination for Single Ended and Differential Signaling Device Load
NB3V63143G
PARAMETER MEASUREMENT TEST CIRCUITS
CLKx
LVCMOS
Clock
Hi−Z Probe
CL
Measurement
Equipment
Figure 7. LVCMOS Parameter Measurement
CLK1
Hi−Z Probe
2 pF
HCSL
Clock
Measurement
Equipment
Hi−Z Probe
CLK0
50 W
2 pF
50 W
Figure 8. HCSL Parameter Measurement
CLK1
LVDS
Clock
Hi−Z Probe
Measurement
Equipment
100 W
Hi−Z Probe
CLK0
Figure 9. LVDS Parameter Measurement
www.onsemi.com
13
NB3V63143G
TIMING MEASUREMENT DEFINITIONS
t2
tDC = 100 * t1 / t2
t1
VDDO
80% of VDDO
50% of VDDO
20% of VDDO
LVCMOS
Clock Output
GND
tF
tR
Figure 10. LVCMOS Measurement for AC Parameters
t2
tDC = 100 * t1/t2
tPeriod = t2
t1
80%
80%
Vcross = 50% of output swing
20%
DVcross
20%
tR
tF
Figure 11. Differential Measurement for AC Parameters
tperiod−jitter
50% of CLK Swing
Clock
Output
tNcycle
t(N+1)cycle
50% of CLK Swing
Clock
Output
tCTC−jitter = t(N+1)cycle − tNcycle (over 1000 cycles)
Figure 12. Period and Cycle−Cycle Jitter Measurement
www.onsemi.com
14
NB3V63143G
Toutput enable
Toutput disable
OE
VIH
VIL
CLK Output
With Hi-Z in
disable mode
ÏÏÏÏÏÏ
High-Z
ÏÏÏÏÏÏ
CLK Output
with output
Low in disable
mode
Tpower-up
Tpower-down
PD#
VIH
VIL
CLK Output
Figure 13. Output Enable/ Disable and Power Down Functions
www.onsemi.com
15
NB3V63143G
APPLICATION GUIDELINES
Crystal Input Interface
Output Interface and Terminations
Figure 14 shows the NB3V63143G device crystal
oscillator interface using a typical parallel resonant
fundamental mode crystal. A parallel crystal with loading
capacitance CL = 18 pF would use C1 = 32 pF and C2 =
32 pF as nominal values, assuming 4 pF of stray capacitance
per line.
The NB3V63143G consists of a unique Multi Standard
Output Driver to support LVCMOS, LVDS and HCSL
standards. Termination techniques required for each of these
standards are different to ensure proper functionality. From
the device it is possible to switch off one output driver and
turn on another output driver using the SEL[1:0] pins as part
of the Configuration Settings. The required termination
changes must be considered and taken care of by the system
designer.
C L + (C1 ) Cstray)ń2; C1 + C2
The frequency accuracy and duty cycle skew can be
fine−tuned by adjusting the C1 and C2 values. For example,
increasing the C1 and C2 values will reduce the operational
frequency. Note R1 is optional and may be 0 W.
LVCMOS Interface
LVCMOS output swings rail−to−rail up to VDDO supply
and can drive up to 15 pF load at higher drive stengths. The
output buffer’s drive is programmable up to four steps,
though the drive current will depend on the step setting as
well as the VDDO supply voltage. (See Figure 15 and
Table 8). Drive strength must be configured high for driving
higher loads. The slew rate of the clock signal increases with
higher output current drive for the same load. The software
lets the user choose the load drive current value per
LVCMOS output based on the VDDO supply selected.
Figure 14. Crystal Interface Loading
Table 8. LVCMOS DRIVE LEVEL SETTINGS
VDDO Supply
Load Current Setting 3
Max Load Current
Load Current Setting 2
Load Current Setting 1
Load Current Setting 0
Min Load Current
1.8 V
8 mA
4 mA
2 mA
1 mA
The IDDO current consists of the static current
component (varies with drive) and dynamic current
component. For any VDDO, the IDDO dynamic current
range per LVCMOS output can be approximated by the
following:
Cload includes the load capacitor connected to the output,
the pin capacitor posed by the output pin (typically 5 pF) and
the cap load posed by the receiver input pin. Cload = (CL +
Cpin+ Cin)
An optional series resistor Rs can be connected at the
output for impedance matching, to limit the overshoots and
ringings.
IDDO + f out * C load * VDDO
www.onsemi.com
16
NB3V63143G
VDD
Drive Strength
selection
CLKx
Drive Strength
selection
Figure 15. Simplified LVCMOS Output Structure
LVDS Interface
Differential signaling like LVDS has inherent advantage
of common mode noise rejection and low noise emission,
and thus a popular choice for clock distribution in systems.
TIA/EIA−644 or LVDS is a standard differential,
point−to−point bus topology that supports fast switching
speeds and has the benefit of low power consumption. The
driver consists of a low swing differential with constant
current of 3.5 mA through the differential pair, and
generates switching output voltage across a 100 W
terminating resistor (externally connected or internal to the
receiver). Power dissipation in LVDS standard ((3.5 mA)2 x
100 W = 1.2 mW) is thus much lower than other differential
signalling standards.
A fan−out LVDS buffer (like ON Semiconductor’s
NB6N1xS and NB6L1xS) can be used as an extension to
provide clock signal to multiple LVDS receivers to drive
multiple point−to−point links to receiving node.
VDDO
Iss
CLK 1
+
RT
100 W
Vout
_
CLK 0
+
Vin
_
Iss
Figure 16. Simplified LVDS Output Structure with Termination
www.onsemi.com
17
NB3V63143G
HCSL Termination
overshoot and ringing due to the rapid rise of current from
the output driver. The open source driver has high internal
impedance; thus a series resistor up to 33 W does not affect
the signal integrity. This resistor can be avoided for VDDO
supply (1.8 V) of operation, unless impedance matching
requires it.
HCSL is a differential signaling standard commonly used
in PCIe systems. The HCSL driver is typical 14.5 mA
switched current open source output that needs a 50 W
termination resistor to ground near the source, and generates
725 mV of signal swing. A series resistor (10 W to 33 W) is
optionally used to achieve impedance matching by limiting
14.5mA
2.6mA
CLK1
CLK0
50 W
50 W
Figure 17. Simplified HCSL Output Structure with Termination
Field Programming Kit and Software
depends on the trace length and the propogation delay. For
eg. On an FR4 PCB with approximately 150 ps/inch of
propogation rate on a 2 inch trace, the ripple frequency = 1
/ (150 ps * 2 inch * 5) = 666.6 MHz; [5 = number of times
the signal travels, 1 trip to receiver plus 2 additional round
trips].
PCB traces should be terminated when trace length >= tr/f
/ (2* tprate); tf/t = rise/ fall time of signal, tprate =
propagation rate of trace.
The NB3V63143G can be programmed by the user using
the ‘Clock Cruiser Programmable Clock Kit’. This device
uses the 16L daughter card on the hardware kit. To design a
new clock, ‘Clock Cruiser Software’ is required to be
installed from the ON Semiconductor website. The user
manuals for the hardware kit Clock Cruiser Programmable
Clock Kit and Clock Cruiser Software can be found
following this link www.onsemi.com.
ÌÌÑ
Recommendation for Clock Performance
Overshoot
(Positive)
Clock performance is specified in terms of Jitter in the
time domain. Details and measurement techniques of
Cycle−cycle jitter, period jitter, TIE jitter and Phase Noise
are explained in application note AND8459/D.
In order to have a good clock signal integrity for minimum
data errors, it is necessary to reduce the signal reflections.
The reflection coefficient can be zero only when the source
impedance equals the load impedance. Reflections are based
on signal transition time (slew rate) and due to impedance
mismatch. Impedance matching with proper termination is
required to reduce the signal reflections. The amplitude of
overshoots is due to the difference in impedance and can be
minimized by adding a series resistor (Rs) near the output
pin. Greater the difference in impedance, greater is the
amplitude of the overshoots and subsequent ripples. The
ripple frequency is dependant on the signal travel time from
the receiver to the source. Shorter traces results in higher
ripple frequency, as the trace gets longer the travel time
increases, reducing the ripple frequency. The ripple
frequency is independent of signal frequency, and only
Ringing
ÌÌÌÑ
Overshoot
(Negative)
Figure 18. Signal Reflection Components
www.onsemi.com
18
NB3V63143G
PCB Design Recommendation
source or the receiver. In an optimum layout all components
are on the same side of the board, minimizing vias through
other signal layers.
For a clean clock signal waveform it is necessary to have
a clean power supply for the device. The device must be
isolated from system power supply noise. A 0.1 mF and a
2.2 mF decoupling capacitor should be mounted on the
component side of the board as close to the VDD pin as
possible. No vias should be used between the decoupling
capacitor and VDD pin. The PCB trace to VDD pin and the
ground via should be kept as thick and as short as possible.
All the VDD pins should have decoupling capacitors.
Stacked power and ground planes on the PCB should be
large. Signal traces should be on the top layer with minimum
vias and discontinuities and should not cross the reference
planes. The termination components must be placed near the
VDD
PD#
Device Applications
The NB3V63143G is targeted mainly for the Consumer
market segment and can be used as per the examples below.
Clock Generator
Consumer applications like a Set top Box, have multiple
sub−systems and standard interfaces and require multiple
reference clock sources at various locations in the system.
This part can function as a clock generating IC for such
applications generating a reference clock for interfaces like
USB, Ethernet, Audio/Video, ADSL, PCI etc.
SEL0 SEL1
Input
Decoder
Output control
Crystal /Clock Control
Configuration
Memory
VDDO0
Frequency
and SS
Reference
Clock XIN/CLKIN
Crystal
XOUT
Clock Buffer/
Crystal
Oscillator And
AGC
Output
Divider
PLL Block
25MHz
Phase
Detector
Charge
Pump
CMOS/
DIFF
buffer
27MHz
Video
48MHz
USB
25MHz
Ethernet
OE0
VDDO1
VCO
Output
Divider
CMOS /
DIFF
buffer
Feedback
Divider
CLK1
OE1
VDDO2
Output
Divider
PLL Bypass Mode
GND
CLK0
CMOS
buffer
CLK2
OE2
GNDO
Figure 19. Application as Clock Generator
Buffer and Logic/Level Translator
The NB3V63143G is useful as a simple CMOS Buffer in
PLL bypass mode. One or more outputs can use the PLL
Bypass mode to generate the buffered outputs. If the PLL is
configured to use spread spectrum, all outputs using PLL
Bypass feature will not be subjected to the spread spectrum.
The device can be simultaneously used as logic translator for
converting the LVCMOS input clock to LVDS, HCSL or
LVCMOS (with different output voltage level).
For instance in applications like an LCD monitor, for
converting the LVCMOS input clock to LVDS output.
www.onsemi.com
19
NB3V63143G
VDD
PD#
SEL0 SEL1
Input
Decoder
Output control
Crystal /Clock Control
Configuration
Memory
VDDO0
Frequency
and SS
Clock Buffer/
Crystal
Oscillator And
AGC
Reference XIN/CLKIN
Clock
XOUT
LVCMOS
PLL Block
Charge
Pump
Phase
Detector
CMOS/
DIFF
buffer
Output
Divider
CLK0
OE0
VDDO1
VCO
CMOS /
DIFF
buffer
Output
Divider
CLK1
Feedback
Divider
OE1
VDDO2
Output
Divider
CMOS
buffer
NOTE:
GNDO
LVCMOS
CLK2
PLL Bypass Mode
GND
LVDS
OE2
Figure 20. Application as Level Translator
Since the device requirement is VDDO ≤ VDD, LVCMOS signal level cannot be translated to a higher level of LVCMOS voltage.
EMI Attenuator
clock outputs (not bypass outputs) even if they are at
different frequencies. In Figure 21, CLK0 uses the PLL and
hence is subjected to the spread spectrum modulation while
CLK1 and CLK2 use the PLL Bypass mode and hence are
not subjected to the spread spectrum modulation.
Spread spectrum through frequency modulation
technique enables the reduction of EMI radiated from the
high frequency clock signals by spreading the spectral
energy to the nearby frequencies. While using frequency
modulation, the same selection is applied to all the PLL
VDD
PD#
SEL0 SEL1
Input
Decoder
Output control
Crystal /Clock Control
Configuration
Memory
VDDO0
Frequency
and SS
Reference
Clock XIN/CLKIN
Crystal
XOUT
Clock Buffer/
Crystal
Oscillator And
AGC
Output
Divider
PLL Block
Phase
Detector
Charge
Pump
CMOS/
DIFF
buffer
CMOS /
DIFF
buffer
Feedback
Divider
PLL Bypass Mode
GNDO
CPU
CLK1
12MHz
USB1
12MHz
USB2
OE1
VDDO2
Output
Divider
GND
12MHz +/- 0.375 %
OE0
VDDO1
VCO
Output
Divider
12MHz
CLK0
CMOS
buffer
CLK2
OE2
Figure 21. Application as EMI Attenuator
ORDERING INFORMATION
Type
Package
Shipping†
NB3V63143G00MNR2G
Blank Device
QFN−16
(Pb−Free)
3000 / Tape & Reel
NB3V63143GxxMNR2G
Factory Pre−programmed
Device
QFN−16
(Pb−Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
†Note: Please contact your ON Semiconductor sales representative for availability in tube.
www.onsemi.com
20
NB3V63143G
PACKAGE DIMENSIONS
QFN16 3x3, 0.5P
CASE 485AE
ISSUE B
D
A
B
ÇÇ
ÇÇ
PIN 1
LOCATION
L1
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
E
ÉÉÉ
ÉÉÉ
0.15 C
EXPOSED Cu
0.15 C
TOP VIEW
0.10 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. OUTLINE MEETS JEDEC DIMENSIONS PER
MO−220, VARIATION VEED−6.
L
L
A1
DETAIL B
(A3)
DETAIL B
MOLD CMPD
ÉÉ
ÉÉ
ÇÇ
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
A3
ALTERNATE
CONSTRUCTIONS
A
0.08 C
A1
SIDE VIEW
NOTE 4
C
SEATING
PLANE
D2
16X
L
RECOMMENDED
SOLDERING FOOTPRINT*
DETAIL A
5
8
3.30
9
4
16X
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
1.25
1.55
3.00 BSC
1.25
1.55
0.50 BSC
0.20
−−−
0.30
0.50
0.00
0.15
16X
0.65
PACKAGE
OUTLINE
E2
K
1
1
b
0.10 C A B
12
16
3.30
13
16X
0.05 C
NOTE 3
e
e/2
BOTTOM VIEW
16X
0.30
0.50
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
21
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB3V63143G/D