MC10E1652 D

MC10E1652
5V, -5V Dual ECL Output
Comparator with Latch
The MC10E1652 is fabricated using ON Semiconductor’s advanced
MOSAIC III process and is output compatible with 10H logic devices.
In addition, the device is available in a 20-pin surface mount package.
However, the MC10E1652 provides user programmable hysteresis.
The latch enable (LENa and LENb) input pins operate from standard
ECL 10H logic levels. When the latch enable is at a logic high level,
the MC10E1652 acts as a comparator; hence, Q will be at a logic high
level if V1 > V2 (V1 is more positive than V2). Q is the complement
of Q. When the latch enable input goes to a low logic level, the outputs
are latched in their present state, providing the latch enable setup and
hold time constraints are met. The level of input hysteresis is
controlled by applying a bias voltage to the HYS pin.
Features
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
MARKING
DIAGRAM
1 20
20 1
PLCC−20
FN SUFFIX
CASE 775
MC10E
1652FNG
AWLYYWW
Typical 3.0 dB Bandwidth > 1.0 GHz
A
WL
YY
WW
G
Typical V to Q Propagation Delay of 775 ps
Typical Output Rise/Fall of 350 ps
Common Mode Range −2.0 V to +3.0 V
Individual Latch Enables
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
Differential Outputs
Operating Mode: VCC = 5.0 V, VEE = −5.2 V, GND = 0 V
ORDERING INFORMATION
Programmable Input Hysteresis
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
No Internal Input Pulldown Resistors
ESD Protection: Human Body Model; > 2 kV,
Machine Model; > 100 V
Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
•
• Moisture Sensitivity Level 3
For Additional Information, see Application Note AND8003/D
• Flammability Rating: UL 94 V−O @ 0.125 in,
Oxygen Index: 28 to 34
Transistor Count = 85 devices
•
• These are Pb−Free Devices*
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2013
April, 2013 − Rev. 10
1
Publication Order Number:
MC10E1652/D
MC10E1652
Qb LENb NC
18
17
16
V1b
V2b
15
14
Qb
19
13
VCC
GND
20
12
HYS
NC
1 Pinout: 20-Lead PLCC 11
NC
GND
2
10
VEE
Qa
3
9
VCC
(Top View)
4
5
6
Qa LENa NC
7
8
V2a
V1a
* All VCC and VCCO pins are NOT tied together on the die.
Warning: All VCC, GND, and VEE pins must be externally
connected to Power Supply to guarantee proper operation.
Figure 1. Logic Diagrams and Pinout Assignments
V1a
Qa
V2a
LENa
Qa
HYS
V1b
Qb
V2b
Qb
LENb
VEE = -5.2 V
VCC = +5.0 V
Figure 2. Logic Diagram
Table 2. FUNCTION TABLE
Table 1. PIN DESCRIPTION
PIN
FUNCTION
Qa, Qa
ECL Differential Outputs (a)
Qb, Qb
ECL Differential Outputs (b)
LENa, LENb
ECL Latch Enable
V1a, V1b
Input Comparator 1
V2a, V2b
Input Comparator 2
HYS
Hysteresis Bias Voltage Control Input
VCC
Positive Supply
VEE
Negative Supply
NC
No Connect
GND
Ground
LEN
V1, V2
Function
H
H
L
V1 > V2
V1 < V2
X
H
L
Latched
http://onsemi.com
2
MC10E1652
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Units
|VEE| + |VCC|
12.0
V
|V1 − V2|
3.7
V
VEE v VI v VCC
V
50
100
mA
mA
± 0.5
mA
VSUP
Total Supply Voltage
VPP
Differential Input Voltage
VI
Input Voltage
Iout
Output Current
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction to Ambient)
0 LFPM
500 LFPM
28 PLCC
28 PLCC
qJC
Thermal Resistance (Junction to Case)
std bd
28 PLCC
VEE
Operating Range
GND = 0 V
Tsol
Wave Solder
Continuous
Surge
Pb−Free
0 to +85
°C
−65 to +150
°C
63.5
43.5
°C/W
°C/W
22 to 26
°C/W
−4.2 to −5.7
V
265
°C
v 3 sec @ 260°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. DC CHARACTERISTICS VCC = +5.0 V ±5%; VEE = −5.2 V ±5%, VCC = 0 V (Note 1)
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
Min
Typ
85°C
Max
Min
Typ
Max
Unit
VOH
Output HIGH Voltage (Note 2)
−1020
−840
−980
−810
−920
−735
mV
VOL
Output Low Voltage (Note 2)
−1950
−1630
−1950
−1630
−1950
−1600
mV
VIL
Input LOW Voltage (LEN)
−1.95
−1.48
−1.95
−1.48
−1.95
−1.45
mV
VIH
Input HIGH Voltage (LEN)
−1.17
−0.84
−1.13
−0.81
−1.07
−0.735
mV
II
IIH
Input Current (V1, V2)
Input HIGH Current (LEN)
65
150
65
150
65
150
mA
ICC
IEE
Positive Supply Current
Negative Supply Current
50
−55
50
−55
50
−55
mA
VCMR
Common Mode Range (Note 3)
3.0
V
Hys
Hysteresis (Note 4)
Vskew
Hysteresis Skew (Note 5)
Cin
Input Capacitance
−2.0
3.0
−2.0
3.0
−2.0
27
27
30
mV
−1.0
−1.0
0
mV
PLCC
2
2
2
pF
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input VIL and VIH parameters vary 1:1 with VCC. Output VOH and VOL parameters vary 1:1 with GND.
2. Outputs are terminated through a 50 ohm resistor to GND−2 volts.
3. VCMR Min varies 1:1 with VEE; Max varies 1:1 with VCC.
4. The HYS pin programming characterization information is shown in Figure 2. The hysteresis values indicated in the data sheet are for the
condition in which the voltage on the HYS pin is set to VEE.
5. Hysteresis skew (Vskew) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
27 mV and the Vskew value indicates that the hysteresis was skewed from the reference level by 1 mV in the negative direction. Hence the
hysteresis window ranged from 14 mV below the reference level to 13 mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0 mV. The hysteresis skew values apply over the programming range shown in Figure 2.
http://onsemi.com
3
MC10E1652
40
-1.0
HYSTERESIS, (mV)
Q, OUTPUT VOLTAGE (V)
-0.8
HYSTERESIS
-1.2
-1.4
-1.6
-1.8
-20 -16 -12 -8
-4 Vref
4
8
12
16
30
T=
25°C
20
T = 0°C
10
0
-0.2
20
Vin, DIFFERENTIAL INPUT VOLTAGE (mV)
T=
85°C
-0.1
0.0
0.1
0.2
0.3
0.4
0.5
PROGRAMMING VOLTAGE (VOLTAGE ABOVE VEE)
Figure 3. Typical Hysteresis Curve
Figure 4. Hysteresis Programming Voltage
Table 5. AC CHARACTERISTICS VCC = +5.0 V ±5%; VEE = −5.2 V ±5%, VCC = 0 V (Note 6)
0°C
Symbol
Characteristic
Min
fMAX
Maximum Toggle Frequency
tPLH
tPHL
Propagation Delay to Output (Note 7)
ts
Setup Time
th
Enable Hold Time
tpw
Minimum Pulse Width
tskew
Within Device Skew (Note 8)
tJITTER
Cycle−to−Cycle Jitter
TDE
Delay Dispersion
TDL
Delay Dispersion
VPP
Differential Input Voltage
tr
tf
Rise/Fall Times
(20-80%)
Typ
25°C
Max
Min
TBD
Typ
85°C
Max
Min
> 1.0
Typ
Max
TBD
Unit
GHz
ps
V to Q
LEN to Q
750
550
900
725
V
450
V
−50
LEN
400
1050
900
775
550
925
750
300
450
−250
−50
1075
900
850
650
1025
825
300
550
350
−250
−100
−250
1200
1000
ps
ps
ps
400
400
15
15
15
ps
TBD
TBD
TBD
ps
ps
(ECL Levels) (Notes 9 10)
(Notes 9, 11)
100
60
(TTL Levels) (Notes 12, 13)
(Notes 11, 12)
350
100
ps
|V1 − V2|
3.7
3.7
3.7
V
ps
225
325
475
225
325
475
250
375
500
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
6. Input VIL and VIH parameters vary 1:1 with VCC. Output VOH and VOL parameters vary 1:1 with GND.
7. The propagation delay is measured from the crosspoint of the input signal and the threshold value to the crosspoint of the Q and Q output
signals. For propagation delay measurements the threshold level (VTHR) is centered about an 850 mV input logic swing with a slew rate of
0.75 V/NS. There is an insignificant change in the propagation delay over the input common mode range.
8. tskew is the propagation delay skew between comparator A and comparator B for a particular part under identical input conditions.
9. Refer to Figure 4 and note that the input is at 850 mV ECL levels with the input threshold range between the 20% and 80% points. The delay
is measured from the crosspoint of the input signal and the threshold value to the crosspoint of the Q and Q output signals.
10. The slew rate is 0.25 V/NS for input rising edges.
11. The slew rate is 0.75 V/NS for input rising edges.
12. Refer to Figure 5 and note that the input is at 2.5 V TTL levels with the input threshold range between the 20% and 80% points. The delay
is measured from the crosspoint of the input signal and the threshold value to the crosspoint of the Q and Q output signals.
13. The slew rate is 0.3 V/NS for input rising edges.
http://onsemi.com
4
MC10E1652
APPLICATIONS INFORMATION
The timing diagram (Figure 5.) is presented to illustrate
the MC10E1652’s compare and latch features. When the
signal on the LEN pin is at a logic high level, the device is
operating in the “compare mode,” and the signal on the input
arrives at the output after a nominal propagation delay (tPHL,
tPLH). The input signal must be asserted for a time, ts, prior
to the negative going transition on LEN and held for a time,
th, after the LEN transition. After time th, the latch is
operating in the “latch mode,” thus transitions on the input
do not appear at the output. The device continues to operate
in the “latch mode” until the latch is asserted once again.
Moreover, the LEN pulse must meet the minimum pulse
width (tpw) requirement to effect the correct input-output
relationship. Note that the LEN waveform in Figure 5.
shows the LEN signal swinging around a reference labeled
VBBINT; this waveform emphasizes the requirement that
LEN follow typical ECL 10KH logic levels because
VBBINT is the internally generated reference level, hence is
nominally at the ECL VBB level.
Finally, VOD is the input voltage overdrive and represents
the voltage level beyond the threshold level (VTHR) to which
the input is driven. As an example, if the threshold level is
set on one of the comparator inputs as 80 mV and the input
signal swing on the complementary input is from zero to 100
mV, the positive going overdrive would be 20 mV and the
negative going overdrive would be 80 mV. The result of
differing overdrive levels is that the devices have shorter
propagation delays with greater overdrive because the
threshold level is crossed sooner than the case of lower
overdrive levels. Typically, semiconductor manufactures
refer to the threshold voltage as the input offset voltage
(VOS) since the threshold voltage is the sum of the
externally supplied reference voltage and inherent device
offset voltage.
VBBINT
LEN
tpw
ts
V
VIN
th
VOD
VTHR
tPLH(LEN)
tPHL
Q
Q
Figure 5. Input/Output Timing Diagram
http://onsemi.com
5
MC10E1652
DELAY DISPERSION
Under a constant set of input conditions comparators have
a specified nominal propagation delay. However, since
propagation delay is a function of input slew rate and input
voltage overdrive the delay dispersion parameters, TDE and
TDT, are provided to allow the user to adjust for these
variables (where TDE and TDT apply to inputs with standard
ECL and TTL levels, respectively).
Figure 6. and Figure 7. define a range of input conditions
which incorporate varying input slew rates and input voltage
overdrive. For input parameters that adhere to these
constraints the propagation delay can be described as:
TNOM ± TDE (or TDT)
where TNOM is the nominal propagation delay. TNOM
accounts for nonuniformity introduced by temperature and
voltage variability, whereas the delay dispersion parameter
takes into consideration input slew rate and input voltage
overdrive variability. Thus a modified propagation delay can
be approximated to account for the effects of input conditions
that differ from those under which the parts where tested. For
example, an application may specify an ECL input with a
slew rate of 0.25 V/NS, an overdrive of 17 mV and a
temperature of 25°C, the delay dispersion parameter would
be 100 ps. The modified propagation delay would be
775 ps ± 100 ps
-0.9 V
- 1.07 V
INPUT
THRESHOLD
RANGE
2.5 V
2.0 V
SLEW RATE =
0.25 V/NS
INPUT
THRESHOLD
RANGE
SLEW RATE = 0.75 V/NS
- 1.58 V
- 1.75 V
SLEW RATE =
0.30 V/NS
SLEW RATE = 0.75 V/NS
0.5 V
0V
Figure 6. ECL Dispersion Test Input Conditions
Figure 7. TTL Dispersion Test Input Conditions
http://onsemi.com
6
MC10E1652
Zo = 50 W
Q
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = GND − 2.0 V
Figure 8. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020 − Termination of ECL Logic Devices.)
ORDERING INFORMATION
Package
Shipping†
MC10E1652FNG
PLCC−20
(Pb−Free)
46 Units / Rail
MC10E1652FNR2G
PLCC−20
(Pb−Free)
500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
http://onsemi.com
7
MC10E1652
PACKAGE DIMENSIONS
20 LEAD PLLC
CASE 775−02
ISSUE F
B
0.007 (0.180)
Y BRK
−N−
M
T L-M
0.007 (0.180)
U
M
N
S
T L-M
S
G1
0.010 (0.250)
S
N
S
D
−L−
−M−
Z
W
20
D
1
X
V
S
T L-M
S
N
S
VIEW D−D
A
0.007 (0.180)
M
T L-M
S
N
S
R
0.007 (0.180)
M
T L-M
S
N
S
Z
C
H
−T−
VIEW S
G1
0.010 (0.250) S T L-M
SEATING
PLANE
F
0.007 (0.180)
VIEW S
S
N
T L-M
S
N
S
K
0.004 (0.100)
J
M
K1
E
G
0.007 (0.180)
S
NOTES:
1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M,
1982.
2. DIMENSIONS IN INCHES.
3. DATUMS −L−, −M−, AND −N− DETERMINED WHERE TOP
OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD
PARTING LINE.
4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT
DATUM −T−, SEATING PLANE.
5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH.
ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE.
6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER
THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE
BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY
MISMATCH BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION
TO BE GREATER THAN 0.037 (0.940). THE DAMBAR
INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO
BE SMALLER THAN 0.025 (0.635).
http://onsemi.com
8
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.021
0.050 BSC
0.026
0.032
0.020
−−−
0.025
−−−
0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
−−− 0.020
2_
10 _
0.310
0.330
0.040
−−−
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.53
1.27 BSC
0.66
0.81
0.51
−−−
0.64
−−−
8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
−−−
0.50
2_
10 _
7.88
8.38
1.02
−−−
M
T L-M
S
N
S
MC10E1652
ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10E1652/D