NCP5369 D

NCP5369
Integrated Driver and
MOSFET
The NCP5369 integrates a MOSFET driver, high−side MOSFET
and low−side MOSFET into a 6 mm x 6 mm 40−pin QFN package.
The driver and MOSFETs have been optimized for high−current
DC−DC buck power conversion applications. The NCP5369
integrated solution greatly reduces package parasitics and board space
compared to a discrete component solution.
www.onsemi.com
MARKING
DIAGRAM
Features
•
•
•
•
•
•
•
1
Capable of Switching Frequencies Up to 1 MHz
Capable of Output Currents Up to 35 A
Internal Bootstrap Diode
Zero Current Detection
Undervoltage Lockout
Internal Thermal Warning / Thermal Shutdown
These are Pb−Free Devices
5V
NCP5369
AWLYYWWG
1 40
QFN40
MN SUFFIX
CASE 485AZ
A
WL
YY
WW
G
12−20 V
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
Thermal
Warning
5V
ORDERING INFORMATION
VIN
THWN
Device
VCIN
ZCD_EN#
ZCD Enable
DISB#
VSWH
Vout
PWM
PWM
CGND
Shipping†
NCP5369MNR2G
QFN40
2500/Tape & Reel
(Pb−Free)
NCP5369MNTWG
QFN40
2500/Tape & Reel
(Pb−Free)
PHASE
Output
Disable
Package
BOOT
PGND
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
Figure 1. Application Schematic
© Semiconductor Components Industries, LLC, 2015
April, 2015 − Rev. 5
1
Publication Order Number:
NCP5369/D
NCP5369
BOOT
VCIN
GH
VIN
3.4 V
97k
PWM
PHASE
187k
Logic
VSWH
ZCD_EN#
Anti−Cross
Conduction
VCIN
PGND
DISB#
UVLO
THWN/THDN
THWN
GL
Figure 2. Simplified Block Diagram
www.onsemi.com
2
BOOT
NC
VCIN
ZCD_EN#
4
2
1
3
GH
CGND
5
PHASE
6
THWN
14
37
CGND
VSWH
15
36
GL
PGND
16
35
VSWH
PGND
17
34
VSWH
PGND
18
33
VSWH
PGND
19
32
VSWH
PGND
20
31
VSWH
PGND 28
VSWH 29
VSWH 30
VSWH
FLAG43
PGND 27
VIN
7
DISB#
38
PGND 25
PGND 26
13
VIN
NC
PWM
39
CGND
FLAG41
PGND 24
VIN
8
40
VIN
FLAG42
PGND 23
12
PGND 22
11
VIN
PGND 21
VIN
9
10 VIN
NCP5369
Figure 3. Pin Connections (Top View)
Table 1. PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1
ZCD_EN#
2
VCIN
3, 8
NC
4
BOOT
Bootstrap Voltage
5, 37, FLAG 41
CGND
Control Signal Ground
6
GH
7
PHASE
Enable Zero Current Detection
Control Input Voltage
No Connect
High Side FET Gate Access
Provides a return path for the high side driver of the internal IC. Place a high frequency ceramic capacitor of 0.1 uF to 1.0 uF from this pin to BOOT pin.
9−14, FLAG 42
VIN
15, 29−35,
FLAG 43
VSWH
Input Voltage
Switch Node Output
16−28
PGND
Power Ground
36
GL
38
THWN
Thermal Warning
39
DISB#
Output Disable Pin
40
PWM
PWM Drive Logic
Low Side FET Gate Access
www.onsemi.com
3
NCP5369
Table 2. ABSOLUTE MAXIMUM RATINGS
Symbol
Pin Name / Rating
Min
Max
Unit
VCIN
Control Input Voltage
−0.3
7
V
VIN
Power Input Voltage
−0.3
30
V
−0.3 V wrt/VSWH
35 V wrt/PGND
40 V < 50 ns wrt/PGND
7 V wrt/VSWH
V
−5 V
−10 V < 200 ns
35 V
40 V < 50 ns
V
Zero Current Detection
−0.3
6.5
V
PWM
PWM Drive Logic
−0.3
6.5
V
DISB#
Output Disable
−0.3
6.5
V
THWN
Thermal Warning
−0.3
6.5
V
Continuous Output Current, FSW = 300 kHz,
VIN = 12 V, VOUT = 1.2 V (Note 1)
−
35
A
Peak Output Current, FSW = 300 kHz, VIN = 12 V, VOUT
= 1.2 V, Duration = 10 ms, Period = 1 sec. (Note 1)
−
50
A
BOOT
Bootstrap Voltage
VSWH
Switch Node Output
ZCD_EN#
TJ
Junction Temperature
−55 to 150
°C
TS
Storage Temperature
−55 to 150
°C
RqJPCB
Thermal Resistance, High−Side FET
13
°C/W
RqJPCB
Thermal Resistance, Low−Side FET
5
°C/W
Moisture Sensitivity Level
3
MSL
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. IOUT rating is based on using a 3 x 3 sq. in. PCB, 6−layer, 1 oz. Copper, TA = 25°C, natural convection.
Table 3. RECOMMENDED OPERATING RANGES
Rating
Control Input Voltage
Input Voltage
Symbol
Min
Typ
Max
Unit
VCIN
4.5
5
5.5
V
VIN
4.5
12
25
V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
www.onsemi.com
4
NCP5369
ELECTRICAL CHARACTERISTICS (Note 2) (VCIN = 5 V, VIN = 12 V, TA = −10°C to +100°C, unless otherwise noted)
Parameter
Symbol
Condition
VCIN Current (normal mode)
−
VCIN Current (shutdown mode)
−
Min
Typ
Max
Unit
DISB# = 5 V, PWM = OSC,
FSW = 400 kHz
14
20
mA
DISB# = GND
15
30
mA
SUPPLY CURRENT
UNDERVOLTAGE LOCKOUT
UVLO Startup
−
3.8
4.35
4.5
V
UVLO Hysteresis
−
150
200
250
mV
0.1
0.4
0.6
V
BOOTSTRAP DIODE
Forward Voltage
−
VCIN = 5 V, forward bias current = 2 mA
PWM INPUT
VPWM_HI
3.6
−
−
V
PWM Input Voltage Mid−State
VPWM_MID
1.3
−
3.0
V
PWM Input Voltage Low
VPWM_LO
−
−
0.7
V
PWM Input Voltage High
Tri−State Shutdown Holdoff Time
tholdoff
250
ns
PWM Input Resistance
63
kW
PWM Input Bias Voltage
2.2
V
OUTPUT DISABLE
Output Disable Input Voltage High
VDISB#_HI
2.0
−
−
V
Output Disable Input Voltage Low
VDISB#_LO
−
−
0.8
V
−
−
500
−
mV
−
20
40
ns
Output Disable Hysteresis
Output Disable Propagation Delay
ZERO CROSS DETECT
Zero Cross Detect High
VZCD_EN#_HI
2.0
−
−
V
Zero Cross Detect Low
VZCD_EN#_LO
−
−
0.8
V
Zero Cross Detect Threshold
−6
mV
ZCD Blanking Timer
250
ns
150
°C
Thermal Warning Hysteresis
15
°C
Thermal Shutdown Temperature
180
°C
Thermal Shutdown Hysteresis
25
°C
THERMAL WARNING/SHUTDOWN
Thermal Warning Temperature
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Performance guaranteed over the indicated operating temperature range by design and/or characterization tested at TJ = TA = 25°C. Low
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
www.onsemi.com
5
NCP5369
APPLICATIONS INFORMATION
Theory of Operation
The NCP5369 prevents cross conduction by monitoring
the status of the MOSFETs and applying the appropriate
amount of “dead−time” or the time between the turn off of
one MOSFET and the turn on of the other MOSFET.
When the PWM input pin goes high, the gate of the
low−side MOSFET (GL pin) will go low after a propagation
delay (tpdlGL). The time it takes for the low−side MOSFET
to turn off (tfGL) is dependent on the total charge on the
low−side MOSFET gate. The NCP5369 monitors the gate
voltage of both MOSFETs and the switchnode voltage to
determine the conduction status of the MOSFETs. Once the
low−side MOSFET is turned off an internal timer will delay
(tpdhGH) the turn on of the high−side MOSFET.
Likewise, when the PWM input pin goes low, the gate of
the high−side MOSFET (GH pin) will go low after the
propagation delay (tpdlGH). The time to turn off the
high−side MOSFET (tfGH) is dependent on the total gate
charge of the high−side MOSFET. A timer will be triggered
once the high−side MOSFET has stopped conducting, to
delay (tpdhGL) the turn on of the low−side MOSFET.
The NCP5369 is an integrated driver and MOSFET
module designed for use in a synchronous buck converter
topology. A single PWM input signal is all that is required
to properly drive the high−side and low−side MOSFETs.
Low−Side Driver
The low−side driver is designed to drive a
ground−referenced low RDS(on) N−Channel MOSFET. The
voltage rail for the low−side driver is internally connected to
VCIN and PGND.
High−Side Driver
The high−side driver is designed to drive a floating low
RDS(on) N−channel MOSFET. The gate voltage for the
high side driver is developed by a bootstrap circuit
referenced to Switch Node (VSWH) pin.
The bootstrap circuit is comprised of the internal diode
and an external bootstrap capacitor. When the NCP5369 is
starting up, the VSWH pin is at ground, so the bootstrap
capacitor will charge up to VCIN through the bootstrap
diode See Figure 1. When the PWM input goes high, the
high−side driver will begin to turn on the high−side
MOSFET using the stored charge of the bootstrap capacitor.
As the high−side MOSFET turns on, the VSWH pin will
rise. When the high−side MOSFET is fully on, the switch
node will be at 12 V, and the BST pin will be at 5 V plus the
charge of the bootstrap capacitor (approaching 17 V).
The bootstrap capacitor is recharged when the switch
node goes low during the next cycle.
Thermal Warning / Thermal Shutdown
When the temperature of the driver reaches 150°C, the
THWN pin will be pulled low indicating a thermal warning.
At this point, the part continues to function normally. When
the temperature drops below 135°C, the THWN will go
high.
If the driver temperature exceeds 180°C, the part will
enter thermal shutdown and turn off both MOSFETs. Once
the temperature falls below 155°C, the part will resume
normal operation. The THWN pin has a maximum current
capability of 30 mA.
Zero Current Detect
When ZCD_EN# is set high, the NCP5369 will operate in
normal PWM mode.
When ZCD_EN# is set low, zero current detect (ZCD)
will be enabled. If PWM goes high, GH will go high after the
non−overlap delay. If PWM goes low, GL will go high after
the non−overlap delay, and stay high for the duration of the
ZCD blanking timer. Once this timer has expired, VSWH
will be monitored for zero current detection, and will pull
GL low once detected. The threshold on VSWH to
determine zero current undergoes an auto-calibration cycle
every time DISB# is brought from low to high. This
auto-calibration cycle typically takes 55 ms to complete.
Power Supply Decoupling
The NCP5369 can source and sink relatively large current
to the gate pins of the MOSFETs. In order to maintain a
constant and stable supply voltage (VCIN) a low ESR
capacitor should be placed near the power and ground pins.
A 1 mF to 4.7 mF multi layer ceramic capacitor (MLCC) is
usually sufficient.
Bootstrap Circuit
The bootstrap circuit uses a charge storage capacitor
(CBST) and the internal diode. The bootstrap capacitor must
have a voltage rating that is able to withstand twice the
maximum supply voltage. A minimum 50 V rating is
recommended. A bootstrap capacitance greater than 100 nF
and a minimum 50 V rating is recommended. A good quality
ceramic capacitor should be used.
Safety Timer and Overlap Protection Circuit
It is very important that MOSFETs in a synchronous buck
regulator do not both conduct at the same time. Excessive
shoot−through or cross conduction can damage the
MOSFETs, and even a small amount of cross conduction
will cause a decrease in the power conversion efficiency.
www.onsemi.com
6
NCP5369
ZCD_EN#
PWM
GH
GL
IL
Figure 4. Zero Current Detection
PWM
GH
GL
tholdoff
tholdoff
Figure 5. Tri−State Operation
www.onsemi.com
7
tholdoff
NCP5369
PACKAGE DIMENSIONS
QFN40 6x6, 0.5P
MN SUFFIX
CASE 485AZ
ISSUE O
A B
D
ÉÉÉ
ÉÉÉ
ÉÉÉ
PIN ONE
LOCATION
2X
L1
DETAIL A
E
ALTERNATE
CONSTRUCTIONS
0.15 C
TOP VIEW
(A3)
DETAIL B
0.10 C
DIM
A
A1
A3
b
D
D2
D3
E
E2
E3
e
G
K
L
L1
MOLD CMPD
DETAIL B
ALTERNATE
CONSTRUCTION
A
43X
0.08 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSIONS: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30mm FROM TERMINAL
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
5. POSITIONAL TOLERANCE APPLIES TO ALL
THREE EXPOSED PADS.
ÉÉÉ
ÉÉÉ
EXPOSED Cu
2X
0.15 C
L
L
SIDE VIEW A1
C
NOTE 4
SEATING
PLANE
0.10 C A B
D3
D2
NOTE 5
G
DETAIL A
40X
MILLIMETERS
MIN
MAX
0.80
1.00
−−−
0.05
0.20 REF
0.18
0.30
6.00 BSC
2.30
2.50
1.40
1.60
6.00 BSC
4.30
4.50
1.90
2.10
0.50 BSC
2.20 BSC
0.20
−−−
0.30
0.50
−−−
0.15
L
SOLDERING FOOTPRINT
6.30
E3
4.56
E2
1.66
E3
1
K
1
G
40
e
40X
e/2
G
BOTTOM VIEW
b
0.10 C A B
0.05 C
40X
0.63
2.56
2.16
4.56
NOTE 3
6.30
2.16
PKG
OUTLINE
40X
0.50
PITCH
0.30
DIMENSIONS: MILLIMETERS
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP5369/D