AMIS 42770 D

AMIS-42770
Dual High Speed CAN
Transceiver
General Description
Controller Area Network (CAN) is a serial communication protocol,
which supports distributed real−time control and multiplexing with high
safety level. Typical applications of CAN−based networks can be found
in automotive and industrial environments.
The AMIS−42770 Dual−CAN transceiver is the interface between
up to two physical bus lines and the protocol controller and will be
used for serial data interchange between different electronic units at
more than one bus line. It can be used for both 12 V and 24 V systems.
The circuit consists of following blocks:
• Two differential line transmitters
• Two differential line receivers
• Interface to the CAN protocol handler
• Interface to expand the number of CAN busses
• Logic block including repeater function and the feedback suppression
• Thermal shutdown circuit (TSD)
Due to the wide common−mode voltage range of the receiver inputs,
the AMIS−42770 is able to reach outstanding levels of electromagnetic
susceptibility (EMS). Similarly, extremely low electromagnetic
emission (EME) is achieved by the excellent matching of the output
signals.
Key Features
Function of the Bus Topology)
• Allows Low Transmit Data Rate in Networks Exceeding 1 km
• Ideally Suited for 12 V and 24 V Industrial and Automotive
•
•
•
•
•
•
SOIC 20
IC SUFFIX
CASE 751AQ
20
AMIS42770
ICAW−N
AWLYYWWG
1
• Fully Compatible with the ISO 11898−2 Standard
• Certified “Authentication on CAN Transceiver Conformance (d1.1)”
• Wide Range of Bus Communication Speed (up to 1 Mbit/s in
•
•
http://onsemi.com
Applications
Low EME: Common−mode−choke is No Longer Required
Differential Receiver with Wide Common−mode Range (±35 V) for
High EMS
No Disturbance of the Bus Lines with an Un−powered Node
Prolonged Dominant Time−out Function Allowing Communication
Speeds Down to 1 kbit/s
Thermal Protection
Bus Pins Protected against Transients
Short Circuit Proof to Supply Voltage and Ground
This is a Pb−Free Device*
A
WL
YY
WW
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2014
November, 2014 − Rev. 4
1
Publication Order Number:
AMIS−42770/D
AMIS−42770
ORDERING INFORMATION
Part Number
Package
Shipping Configuration
Temperature Range
AMIS42770ICAW1G
SOIC−20 300
(Pb−Free, Green)
38 / Tube
−40°C to 125°C
AMIS42770ICAW1RG
SOIC−20 300
(Pb−Free, Green)
1500 / Tape & Reel
−40°C to 125°C
Table 1. TECHNICAL CHARACTERISTICS
Symbol
Min.
Max.
Unit
VCANHx
DC voltage at pin CANH1/2
Parameter
0 < VCC < 5.25 V; no time limit
−45
+45
V
VCANLx
DC voltage at pin CANL1/2
0 < VCC < 5.25 V; no time limit
−45
+45
V
Differential bus output voltage in dominant state
42.5 W < RLT < 60 W
1.5
3
V
CM−range
Input common−mode range for comparator
Guaranteed differential receiver
threshold and leakage current
−35
+35
V
VCM−peak
Common−Mode peak
See Figures 10 and 11 (Note 1)
−1000
+1000
mV
VCM−step
Common−Mode step
See Figures 10 and 11 (Note 1)
−250
+250
mV
Vo(dif)(bus_dom)
Conditions
1. The parameters VCM−peak and VCM−step guarantee low EME.
VCC
12
POR
Thermal
shutdown
AMIS−42770
14
Feedback Suppression
CANL1
Driver
control
Timer
Ri(cm)
VCC/2
−
+
COMP
VCC
Ri(cm)
VCC
19
Driver
control
Feedback Suppression
13
CANH1
2 x timer
clock
Logic
Unit
Timer
10
3
VREF
ENB1
Text
Ri(cm)
VCC/2
+
−
COMP
VCC
VCC
8
4
7
Tx0 Rx0
9
Rint
Figure 1. Block Diagram
http://onsemi.com
2
18
2
ENB2
Ri(cm)
5
6 15 16 17
GND
CANH2
CANL2
AMIS−42770
TYPICAL APPLICATION
Application Description
AMIS−42770 is especially designed to provide the link
between a CAN controller (protocol IC) and two physical
busses. It is able to operate in three different modes:
• Dual CAN
• A CAN−bus extender
• A CAN−bus repeater
Application Schematics
VBAT
CAN BUS 1
CAN BUS 2
5 V−reg
CD
100 nF
VCC
EN1
EN2
Rx0
Tx0
Text
Rint
10
Vref
8 13 CANH1
12
2
14
7
AMIS−42770
4
19
CANL1
CANH2
3
9
5
18
6 15 16 17
RLT
60 W
CANL2
RLT
60 W
GND
Figure 2. Application Diagram CAN−bus Repeater
CAN BUS 1
VBAT
5 V−reg
CD
100 nF
CD
100 nF
VCC
Vref
VCC
EN1
EN2
Rx0
mC
Tx0
CAN
controller
Text
Rint
10
8 13 CANH1
12
2
14
7
AMIS−42770
4
19
CANL1
CANH2
3
9
5
18
6 15 16 17
CANL2
GND
GND
Figure 3. Application Diagram Dual−CAN
http://onsemi.com
3
RLT
60 W
RLT
60 W
CAN BUS 2
AMIS−42770
CAN BUS 1
VBAT
CAN BUS 2
5 V−reg
CD
100 nF
CD
100 nF
VCC
Vref
VCC
EN1
EN2
10
2
Rx0
mC
Tx0
CAN
controller
8 13 CANH1
12
Text
Rint
14
7
AMIS−42770
4
19
CANL1
CANH2
3
9
5
18
6 15 16 17
RLT
60 W
CANL2
RLT
60 W
GND
GND
isolated +5
CAN BUS 3
Dual
OptoCoupler
CD
100 nF
Vref
VCC
EN1
EN2
Rx0
Tx0
Text
Rint
10
8 13 CANH1
12
2
14
7
CANL1
AMIS−42770
4
CANH2
19
3
9
5
6 15 16 17
18
RLT
60 W
CANL2
RLT
60 W
GND
Figure 4. Application Diagram CAN−bus Extender
1
20 NC
EN2
2
19 CANH2
Text
3
18 CANL2
Tx0
4
17 GND
GND
5
GND
6
Rx0
7
14 CANL1
Vref1
8
13 CANH1
Rint
9
12 VCC
EN1
10
11 NC
AMIS−42770
NC
16 GND
15 GND
Figure 5. Pin Out (top view)
http://onsemi.com
4
CAN BUS 4
AMIS−42770
Table 2. PIN DESCRIPTION
Pin
Name
Description
1
NC
2
ENB2
3
Text
Multi−system transmitter Input; internal pull−up
4
Tx0
Transmitter input; internal pull−up
5
GND
Ground connection (Note 2)
6
GND
Ground connection (Note 2)
7
Rx0
Receiver output
8
VREF1
9
Rint
10
ENB1
11
NC
12
VCC
13
CANH1
CANH transceiver I/O bus system 1
14
CANL1
CANL transceiver I/O bus system 1
15
GND
Ground connection (Note 2)
16
GND
Ground connection (Note 2)
17
GND
Ground connection (Note 2)
18
CANL2
CANL transceiver I/O bus system 2
19
CANH2
CANH transceiver I/O bus system 2
20
NC
Not connected
Enable input, bus system 2; internal pull−up
Reference voltage
Multi−system receiver output
Enable input, bus system 1; internal pull−up
Not connected
Positive supply voltage
Not connected
2. In order to ensure the chip performance, all these pins need to be connected to GND on the PCB.
FUNCTIONAL DESCRIPTION
AMIS−42770 can be also used for only one bus system. If
the connections for the second bus system are simply left
open it serves as a single transceiver for an electronic unit.
For correct operation, it is necessary to terminate the open
bus by the proper termination resistor.
Overall Functional Description
AMIS−42770 is specially designed to provide the link
between the protocol IC (CAN controller) and two physical
bus lines. Data interchange between those two bus lines is
realized via the logic unit inside the chip. To provide an
independent switch−off of the transceiver units for both bus
systems by a third device (e.g. the °C), enable−inputs for the
corresponding driving and receiving sections are provided.
As long as both lines are enabled, they appear as one logical
bus to all nodes connected to either of them.
The bus lines can have two logical states, dominant or
recessive. A bus is in the recessive state when the driving
sections of all transceivers connected to the bus are passive.
The differential voltage between the two wires is
approximately zero. If at least one driver is active, the bus
changes into the dominant state. This state is represented by
a differential voltage greater than a minimum threshold and
therefore by a current flow through the terminating resistors
of the bus line. The recessive state is overwritten by the
dominant state.
In case a fault (like short circuit) is present on one of the
bus lines, it remains limited to that bus line where it occurs.
Data interchange from the protocol IC to the other bus
system and on this bus system itself can be continued.
Logic Unit and CAN Controller Interface
The logic unit inside AMIS−42770 provides data transfer
from/to the digital interface to/from the two busses and from
one bus to the other bus. The detailed function of the logic
unit is described in Table 3.
All digital input pins, including ENBx, have an internal
pull−up resistor to ensure a recessive state when the input is
not connected or is accidentally interrupted. A dominant state
on the bus line is represented by a low−level at the digital
interface; a recessive state is represented by a high−level.
Dominant state received on any bus (if enabled) causes a
dominant state on both busses, pin Rint and pin Rx0.
Dominant signal on any of the input pins Tx0 and Text causes
transmission of dominant on both bus lines (if enabled).
Digital inputs Tx0 and Text are used for connecting the
internal logic’s of several IC’s to obtain versions with more
than two bus outputs (see Figure 4). They have also a direct
logical link to pins Rx0 and Rint independently on the EN1x
pins – dominant on Tx0 is directly transferred to both Rx0
and Rint pins, dominant on Text is only transferred to Rx0.
http://onsemi.com
5
AMIS−42770
Transmitters
The driver control circuit ensures that the drivers are
switched on and off with a controlled slope to limit EME.
The driver control circuit will control itself by the thermal
protection circuit, the timer circuit and the logic unit.
The enable signal ENBx allows the transmitter to be
switched off by a third device (e.g. the °C). In the disabled
state (ENBx = high) the corresponding transmitter behaves
as in the recessive state.
The transceiver includes two transmitters, one for each bus
line, and a driver control circuit. Each transmitter is
implemented as a push and a pull driver. The drivers will be
active if the transmission of a dominant bit is required. During
the transmission of a recessive bit all drivers are passive. The
transmitters have a built−in current limiting circuit that
protects the driver stages from damage caused by accidental
short circuit to either positive supply voltage or to ground.
Additionally a thermal protection circuit is integrated.
Table 3. FUNCTION OF THE LOGIC UNIT (bold letters describe input signals)
EN1B
EN2B
TX0
TEXT
Bus 1 State
Bus 2 State
RX0
RINT
0
0
0
0
dominant
dominant
0
0
0
0
0
1
dominant
dominant
0
0
0
0
1
0
dominant
dominant
0
1
0
0
1
1
recessive
recessive
1
1
0
0
1
1
dominant (Note 3)
dominant
0
0
0
0
1
1
dominant
dominant (Note 3)
0
0
0
1
0
0
dominant
recessive
0
0
0
1
0
1
dominant
recessive
0
0
0
1
1
0
dominant
recessive
0
1
0
1
1
1
recessive
recessive
1
1
0
1
1
1
dominant (Note 3)
recessive
0
0
0
1
1
1
recessive
dominant (Note 3)
1
1
1
0
0
0
recessive
dominant
0
0
1
0
0
1
recessive
dominant
0
0
1
0
1
0
recessive
dominant
0
1
1
0
1
1
recessive
recessive
1
1
1
0
1
1
dominant (Note 3)
recessive
1
1
1
0
1
1
recessive
dominant (Note 3)
0
0
1
1
0
0
recessive
recessive
0
0
1
1
0
1
recessive
recessive
0
0
1
1
1
0
recessive
recessive
0
1
1
1
1
1
recessive
recessive
1
1
1
1
1
1
dominant (Note 3)
recessive
1
1
1
1
1
1
recessive
dominant (Note 3)
1
1
3. Dominant detected by the corresponding receiver.
Receivers
recessive state and does not depend on the bus voltage. In the
enabled state the receiver signal sent to the logic unit is
identical to the comparator output signal.
Two bus receiving sections sense the states of the bus
lines. Each receiver section consists of an input filter and a
fast and accurate comparator. The aim of the input filter is
to improve the immunity against high−frequency
disturbances and also to convert the voltage at the bus lines
CANHx and CANLx, which can vary from –12 V to +12 V,
to voltages in the range 0 to 5 V, which can be applied to the
comparators.
The output signal of the comparators is gated by the ENBx
signal. In the disabled state (ENBX = high), the output signal
of the comparator will be replaced by a permanently
Time−out Counter
To avoid that the transceiver drives a permanent dominant
state on either of the bus lines (blocking all communication),
time−out function is implemented. Signals on pins Tx0 and
Text as well as both bus receivers are connected to the logic
unit through independent timers. If the input of the timer
stays dominant for longer than 25 ms (see parameter tdom),
it is replaced by a recessive signal on the timer output.
http://onsemi.com
6
AMIS−42770
Feedback Suppression
exceeds thermal shutdown level. Because the transmitters
dissipate most of the total power, the transmitters will be
switched off only to reduce power dissipation and IC
temperature. All other IC functions continue to operate.
The logic unit described in Table 3 constantly ensures that
dominant symbols on one bus line are transmitted to the
other bus line without imposing any priority on either of the
lines. This feature would lead to an “interlock” state with
permanent dominant signal transmitted to both bus lines, if
no extra measure is taken.
Therefore feedback suppression is included inside the
logic unit of the transceiver. This block masks−out reception
on that bus line, on which a dominant is actively transmitted.
The reception becomes active again only with certain delay
after the dominant transmission on this line is finished.
Fault Behavior
A fault like a short circuit is limited to that bus line where
it occurs; hence data interchange from the protocol IC to the
other bus system is not affected.
When the voltage at the bus lines is going out of the normal
operating range (−12 V to +12 V), the receiver is not allowed
to erroneously detect a dominant state.
Power−on−Reset (POR)
Short Circuits
While Vcc voltage is below the POR level, the POR
circuit makes sure that:
• The counters are kept in the reset mode and stable state
without current consumption
• Inputs are disabled (don’t care)
• Outputs are high impedant; only Rx0 = high−level
• Analog blocks are in power down
• Oscillator not running and in power down
• CANHx and CANLx are recessive
• VREF output high impedant for POR not released
A current−limiting circuit protects the transmitter output
stage from damage caused by an accidental short−circuit to
either positive or negative supply voltage, although power
dissipation increases during this fault condition.
The pins CANHx and CANLx are protected from
automotive electrical transients (according to “ISO 7637”).
ELECTRICAL CHARACTERISTICS
Definitions
All voltages are referenced to GND. Positive currents
flow into the IC. Sinking current means that the current is
flowing into the pin. Sourcing current means that the current
is flowing out of the pin.
Over Temperature Detection
A thermal protection circuit is integrated to prevent the
transceiver from damage if the junction temperature
Table 4. ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Conditions
Supply voltage
Min.
Max.
Unit
−0.3
+7
V
VCANHx
DC voltage at pin CANH1/2
0 < VCC < 5.25 V; no time limit
−45
+45
V
VCANLx
DC voltage at pin CANL1/2
0 < VCC < 5.25 V; no time limit
−45
+45
V
VdigIO
DC voltage at digital IO pins (EN1B, EN2B,
Rint, Rx0, Text, Tx0)
−0.3
VCC + 0.3
V
VREF
DC voltage at pin VREF
−0.3
VCC + 0.3
V
Vtran(CANHx)
Transient voltage at pin CANH1/2
(Note 4)
−150
+150
V
Vtran(CANLx)
Transient voltage at pin CANL1/2
(Note 4)
−150
+150
V
ESD voltage at CANH1/2 and CANL1/2 pins
(Note 5)
(Note 7)
−4
−500
+4
+500
kV
V
ESD voltage at all other pins
(Note 5)
(Note 7)
−2
−250
+2
+250
kV
V
Static latch−up at all pins
(Note 6)
100
mA
Vesd(CANLx/CANHx)
Vesd
Latch−up
Tstg
Storage temperature
−55
+155
°C
Tamb
Ambient temperature
−40
+125
°C
Tjunc
Maximum junction temperature
−40
+150
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
4. Applied transient waveforms in accordance with “ISO 7637 part 3”, test pulses 1, 2, 3a, and 3b (see Figure 6)
5. Standardized human body model (HBM) ESD pulses in accordance to MIL883 method 3015. Supply pin 8 is ±2 kV.
6. Static latch−up immunity: static latch−up protection level when tested according to EIA/JESD78.
7. Standardized charged device model ESD pulses when tested according to EOS/ESD DS5.3−1993.
http://onsemi.com
7
AMIS−42770
Table 5. THERMAL CHARACTERISTICS
Symbol
Parameter
Conditions
Value
Unit
Rth(vj−a)
Thermal resistance from junction to ambient in SO20 package
In free air
85
K/W
Rth(vj−s)
Thermal resistance from junction to substrate of bare die
In free air
45
K/W
DC CHARACTERISTICS
Table 6. DC AND TIMING CHARACTERISTICS
(VCC = 4.75 to 5.25 V; Tjunc = −40 to +150°C; RLT = 60 W unless specified otherwise.)
Parameter
Conditions
ICC
Supply current, no loads on digital outputs, both busses enabled
Dominant transmitted
Recessive transmitted
PORL_VCC
Power−on−reset level on VCC
Symbol
Min.
Typ.
Max.
Unit
45
137.5
19.5
mA
4.7
V
SUPPLY (pin VCC)
2.2
DIGITAL INPUTS (Tx0, Text, EN1B, EN2B)
VIH
High−level input voltage
0.7 x VCC
−
VCC
V
VIL
Low−level input voltage
−0.3
−
0.3 x VCC
V
IIH
High−level input current
VIN = VCC
−5
0
+5
mA
IIL
Low−level input current
VIN = 0 V
−75
−200
−350
mA
Ci
Input capacitance
Not tested
−
5
10
pF
DIGITAL OUTPUTS (pin Rx0, Rint)
Ioh
High−level output current
Vo = 0.7 x VCC
−5
−10
−15
mA
Iol
Low−level output current
Vo = 0.3 x VCC
5
10
15
mA
Reference output voltage
−50 mA < IVREF < +50 mA
0.45 x VCC
0.50 x VCC
0.55 x VCC
V
Reference output voltage for
full common mode range
−35 V <VCANHx < +35 V;
−35 V <VCANLx < +35 V
0.40 x VCC
0.50 x VCC
0.60 x VCC
V
REFERENCE VOLTAGE OUTPUT (pin VREF1)
VREF
VREF_CM
BUS LINES (pins CANH1/2 and CANL1/2)
Vo(reces)(CANHx)
Recessive bus voltage at pin
CANH1/2
VTx0 = VCC; no load
2.0
2.5
3.0
V
Vo(reces)(CANLx)
Recessive bus voltage at pin
CANL1/2
VTx0 = VCC; no load
2.0
2.5
3.0
V
Io(reces) (CANHx)
Recessive output current at
pin CANH1/2
−35 V < VCANHx < +35 V;
0 V < VCC < 5.25 V
−2.5
−
+2.5
mA
Io(reces) (CANLx)
Recessive output current at
pin CANL1/2
−35 V < VCANLx < +35 V;
0 V < VCC < 5.25 V
−2.5
−
+2.5
mA
Vo(dom) (CANHx)
Dominant output voltage at pin
CANH1/2
VTx0 = 0 V
3.0
3.6
4.25
V
Vo(dom) (CANLx)
Dominant output voltage at pin
CANL1/2
VTx0 = 0 V
0. 5
1.4
1.75
V
Vo(dif) (bus)
Differential bus output voltage
(VCANHx − VCANLx)
VTx0 = 0 V; dominant;
42.5 W < RLT < 60 W
1.5
2.25
3.0
V
VTxD = VCC; recessive;
no load
−120
0
+50
mV
Io(sc) (CANHx)
Short circuit output current at
pin CANH1/2
VCANHx = 0 V;VTx0 = 0 V
−45
−70
−120
mA
Io(sc) (CANLx)
Short circuit output current at
pin CANL1/2
VCANLx = 36 V; VTx0 = 0 V
45
70
120
mA
http://onsemi.com
8
AMIS−42770
Table 6. DC AND TIMING CHARACTERISTICS
(VCC = 4.75 to 5.25 V; Tjunc = −40 to +150°C; RLT = 60 W unless specified otherwise.)
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
BUS LINES (pins CANH1/2 and CANL1/2)
Vi(dif)(th)
Differential receiver threshold
voltage
−5 V < VCANLx < +12 V;
−5 V < VCANHx < +12 V;
see Figure 7
0.5
0.7
0.9
V
Vihcm(dif) (th)
Differential receiver threshold
voltage for high common−
mode
−35 V < VCANLx < +35 V;
−35 V < VCANHx < +35 V;
see Figure 7
0.3
0.7
1.05
V
Vi(dif) (hys)
Differential receiver input voltage hysteresis
−35 V < VCANL < +35 V;
−35 V < VCANH < +35 V;
see Figure 7
50
70
100
mV
Ri(cm)(CANHx)
Common−mode input resistance at pin CANH1/2
15
26
37
KW
Ri(cm) (CANLx)
Common−mode input resistance at pin CANL1/2
15
26
37
KW
−3
0
+3
%
25
50
75
KW
Ri(cm)(m)
Ri(dif)
Matching between pin CANH1/2
and pin CANL1/2 common−
mode input resistance
VCANHx = VCANLx
Differential input resistance
Ci(CANHx)
Input capacitance at pin
CANH1/2
VTx0 = VCC; not tested
7.5
20
pF
Ci(CANLx)
Input capacitance at pin
CANL1/2
VTx0 = VCC; not tested
7.5
20
pF
Differential input capacitance
VTx0 = VCC; not tested
3.75
10
pF
Ci(dif)
ILI(CANHx)
Input leakage current at pin
CANH1/2
VCC < PORL_VCC;
−5.25 V < VCANHx < 5.25 V
−350
170
350
mA
ILI(CANLx)
Input leakage current at pin
CANL1/2
VCC < PORL_VCC;
−5.25 V < VCANLx < 5.25 V
−350
170
350
mA
VCM−peak
Common−mode peak during
transition from dom → rec or
rec → dom
See Figure 11
−1000
1000
mV
VCM−step
Difference in common−mode
between dominant and recessive state
See Figure 11
−250
250
mV
THERMAL SHUTDOWN
Tj(sd)
Shutdown junction temperature
°C
150
TIMING CHARACTERISTICS (see Figures 8 and 9)
td(Tx−BUSon)
Delay Tx0/Text to bus active
40
85
120
ns
td(Tx−BUSoff)
Delay Tx0/Text to bus inactive
30
60
115
ns
td(BUSon−RX)
Delay bus active to Rx0/Rint
25
55
115
ns
td(BUSoff−RX)
Delay bus inactive to Rx0/Rint
65
100
145
ns
100
200
ns
4
10
35
ns
15
25
45
ms
300
ns
td(ENxB)
Delay from EN1B to bus active/inactive
td(Tx−Rx)
Delay from Tx0 to Rx0/Rint
and from Text to Rx0
(direct logical path)
tdom
td(FBS)
15 pF on the digital output
Time out counter interval
Delay for feedback suppression release
5+
td(BUSon−RX)
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
http://onsemi.com
9
AMIS−42770
Measurement Set−ups and Definitions
Schematics are given for single CAN transceiver.
+5V
100 nF
Vref
VCC
8 13 CANH1
12
Text
1 nF
Transient
Generator
3
Rint
14
9
AMIS−42770
Tx0
19
CANL1
1 nF
CANH2
4
Rx0
7
10
18
17 16 15 6 5
2
CANL2
GND
EN1
EN2
Figure 6. Test Circuit for Automotive Transients
VRxD
High
Low
Hysteresis
0,9
0,5
Vi(dif)(hys)
Figure 7. Hysteresis of the Receiver
+5 V
100 nF
Vref
VCC
12
Text
Rint
8 13
CANH1
RLT
3
14
9
AMIS−42770
Tx0
19
CANL1
7
10
RLT
2
17 16 15
6
18
5
CANL2
60 W
GND
EN1
EN2
Figure 8. Test Circuit for Timing Characteristics
http://onsemi.com
10
CLT
100 pF
CANH2
4
Rx0
60 W
CLT
100 pF
AMIS−42770
Tx0
Text
0,7 VCC
0,3 VCC
VCANHx−BUS
VCANHx
VCANLx
VDIFF =
VCANHx
− VCANLx
dominant
5V
0,9 V
0,9 V
0,5 V
0V
0,5 V
tPD(H)
recessive
0,7 VCC
Rx0
Rint
0,7 VCC
0,3 VCC
td(Tx−Rx)
0,3 VCC
td(Tx−Rx)
td(Tx−BUSoff)
td(Tx−BUSon)
td(BUSon−Rx)
td(BUSoff−Rx)
Figure 9. Timing Diagram for AC Characteristics
+5 V
100 nF
Vref
VCC
Rint
Active Probe
14
9
AMIS−42770
19
CANL1
7
10
2
17 16 15
6
18
5
6.2 kW
CANH2
30 W
4
Rx0
10 nF
3
Tx0
Gen
6.2 kW
8 13 CANH1
12
Text
Spectrum Anayzer
30 W
CANL2
47 nF
GND
EN1
EN2
Figure 10. Basic Test Set−up for Electromagnetic Measurement
http://onsemi.com
11
AMIS−42770
CANHx
CANLx
recessive
VCM−peak
VCM−peak
VCM = 0.5*
(VCANHx + VCANLx)
VCM−peak
Figure 11. Common−mode Voltage Peaks (see Measurement Set−up Figure 10)
Company or Product Inquiries
For more information about ON Semiconductor’s products or services visit our Web site at http://www.onsemi.com.
http://onsemi.com
12
AMIS−42770
PACKAGE DIMENSIONS
SOIC 20 W
CASE 751AQ
ISSUE O
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
AMIS−42770/D